Toptek Communications PA-200V Series VHF 144-148 MHz 200W Power Amplifiers PA-200V-H

4 out of 5 stars ( 1 )

Part Number: TEK-PA-200V-H

Not Available

Amplifier, VHF, 2m, 144-148 MHz, 200W Out Max., 5-50W In, FM, SSB, CW, RX Preamp, LED Meter, SWR Protect, PTT IN, SO-239, Req.13.8Vdc@25A min., Each
See More Specifications

Toptek Communications PA-200V Series VHF 144-148 MHz 200W Power Amplifiers PA-200V-H

Toptek Communications PA-200V Series VHF 144-148 MHz 200W Power Amplifiers PA-200V-H

TEK-PA-200V-H

4 out of 5 stars ( 1 )

Part Number: TEK-PA-200V-H

Not Available

Overview

Brand:
Manufacturer's Part Number:
PA-200V-H
Part Type:
Product Line:
DXE Part Number:
TEK-PA-200V-H

Toptek Communications PA-200V Series VHF 144-148 MHz 200W Power Amplifiers

Toptek Communications PA-200V Series VHF 144-148 MHz 200W Power Amplifiers are high-power linear amplifiers designed for Amateur Radio 2 Meter All-Mode operations on FM, SSB, and CW. Amplify your 2-meter transceiver to 200 watts maximum output.

The TEK-PA-200V/C operates with 5 to 50 watts input from your Mobile or Base Transceiver, with approximately 25 watts required for full output. They have a built-in low noise 15 dB GaAs FET receive pre-amplifier to increase weak incoming signals. These power amplifiers run on 13.8 V DC at 25 amps (power supply not included.) Output power is detected by a built-in precision micro-strip line coupler that is tied to a monolithic IC LED driver. The 5-segment LED bar graph indicates a Full Scale reading of 150-200 watt output. A sixth red LED segment serves as a Fault Protection Indicator. NOTE: This amplifier is not intended for FT8 or other digital mode continuous key-down operations.

PA-200V/C Series VHF Amplifiers have these important features:

* Front panel LED indication of output power
* Automatic fault protection for SWR over 2:1
* Built-in low-noise receive preamplifier, with nominal 15 dB gain
* Rear panel PTT Input for proper keyed operation in SSB, CW, and Digital Modes (3.5mm Tip=PTT Ground To TX; Sleeve-Ring=Shield-Chassis Ground; mono or stereo plug).
* RF sense keying for FM mode (PTT connection not required for FM)
* Mode switch for automatic SSB delay and peak power metering
* Amplifier Input Range and Standby Maximum Bypass:
-- PA-200V/C = 5 to 50 watts; 50 watts maximum bypass
* SO-239 UHF female connectors, 50 ohm input and output
* Permanently attached 24 in. (60cm) DC power cable, unterminated
* DC Input: 13.8 Vdc at 25 amp maximum at full output 200 watts (10.5 to 14.8 Vdc operational range)
* Dimensions (WHD) and weight:
PA-200V/C: 7.20 x 3.07 x 12.20 in. (183 x 78 x 310mm); 6.6 lbs. (3.0 kg)

NOTE: Legacy model PA-200V/H with 1-5W input is no longer available.

Documentation

Instruction Sheets for Part Number TEK-PA-200V-H

 Loading...
 Loading...

Reviews Write a Review

Some parts are not legal for use in California or other states with similar laws / regulations

Modal Header

Call To Order

This is a custom order part. You can order this part by Contacting Us.

CA Warning Icon

Cancer and Reproductive Harm -- www.P65Warnings.ca.gov

Email this page