Selected Filters


Availability


24 Results Found For "RG-400"

Part Groups

Results 1 - 24 of 24

DX Engineering RG-400 High Isolation Coaxial Cable Assemblies

DX Engineering RG-400 High Isolation Coaxial Cable Assemblies bring to your RF systems the same quality and capabilities that are demanded of military and aerospace installations. Here are few reasons why we offer these advanced RG-400 cables for your critical applications: - Extremely high isolation from noise and signals from adjacent cables - Very high power handling - 2.75 kW at 30 MHz - Stranded silver plated copper center conductor for extreme efficiency - PTFE dielectric for exceptional dimensional stability, low loss and very high power handling - Silver plated copper braided double shields for very high isolation - Tough, waterproof fluorinated ethylene propylene (FEP) - MIL-C-17 jacket DX Engineering RG-400 cable assemblies are terminated with the classic silver plated Amphenol 831SP PL-259 and UG-175 reducers or BNC Male connectors. DXE-RG400 is specifically recommended for short length cable assembly use in VHF/UHF duplex repeater applications. RG-400 may be the same size as RG-58A/U, but it is an aerospace-level performance cable with dramatically improved ratings in all categories. NOTE: RG-400 is a 0.195 in. diameter cable. RG-400 is NOT related in any way to DXE-400MAX or LMR-400 cables which are 0.405 in. diameter. Order DX Engineering RG-400 High Isolation Coaxial Cable Assemblies here.

5.0 out of 5 stars ( 18 )

$92.99

—

$141.99

RG-400 High-Isolation Double-Shield 50-ohm Coaxial Cable

RG-400 is a high-isolation 50-ohm coaxial cable that is ideal for critical, very low signal level, low noise applications as well as high power handling for RF equipment interconnections. Proper terminations on RG-400 cable assemblies provides extremely low crosstalk and very low noise ingress with a double-braid shielding effectiveness that results in over 100dB of isolation across HF frequencies. This cable is Mil-Spec equivalent to M17/128-RG400. RG-400 is compatible with N-type and PL-259 solder type connectors with UG-175S reducers for RG-58 size cables. NOTE: RG-400 has an OD of 0.195 inch and is NOT the same as DXE-400MAX which is 0.405 inch OD. RG-400 Specs: Center Conductor: Silver Plated Copper – 20AWG Center Conductor Diameter: 0.0384 in. (19 strands of 0.008 in.) Dielectric: PTFE (Polytetrafluoroethylene) Dielectric Diameter: 0.116 in. Shield Construction: Two Layers of Braided Silver Plated Copper Shield Outer Diameter: 0.156 in. Jacket: FEP (Fluorinated ethylene propylene) Cable Overall Diameter: 0.195 in. Minimum Bend Radius: 1.0 in. Weight (lbs. per 1,000 ft.): 50.0 Capacitance: 29.4 pF/ft. Maximum Voltage: 1,900 V Velocity factor (VF), nominal: 69.5% (0.695) Click "More Detail" for more information

5.0 out of 5 stars ( 11 )

$7.49

Amphenol RF Type N Male Crimp Connectors

Amphenol RF Type N Male Crimp Connectors are precision 50-ohm RF coaxial connectors that provide a positive, secure connection for your coaxial cable. Choose one of these different versions of the Type N connectors for your applications: 172102H-2 is our two-pack of the 172102-243 which has a larger center pin ID for DXE-400MAX and LMR-400. They work for 0.405 in. coaxial cables with larger 10 AWG through 11 AWG center conductor, including DXE-8U, some RG-8U, 8214, 9913, etc. 172102-2 is our two-pack of the 172102 that has the standard center pin that fits some RG-8U and RG-213 with smaller center conductors of 12 AWG, 12.5 AWG and 13 AWG. 172100-2 is our two-pack of the 172100 with the standard center pin for RG-58, LMR-195 and RG-400 (not 400MAX) size cables. N-Type connectors are designed to satisfy the need for a durable, weatherproof, medium-size RF connector with consistent performance through 11 GHz. Amphenol RF N-Type connectors feature threaded coupling mechanisms and are fully interchangeable with N-Type connectors made to the MIL-C-39012 specification. These connectors are used in all systems where excellent RF and mechanical performance is critical. Amphenol RF N-Type connectors have high-quality gold-plated center pins to ensure the best performance for any application. They are sold as a pair. Amphenol RF connector details: * Description: Coaxial connector, N-Male * Body Material: Brass * Body Plating: White Bronze * Body Style: Straight * Contact Material: Gold-plated brass * Maximum Frequency: 11 GHz * Dielectric: PTFE * Gender: male (Plug) * Impedance: 50 Ohms Choose the coaxial connectors you need from our wide selection of coax adapters and connectors. When you need Type- N Male connectors, Amphenol RF Type N Male Crimp Connectors are always a good choice. Order yours from DX Engineering today!

4.85 out of 5 stars ( 27 )

$16.99

—

$28.49

DX Engineering Ultra-Grip 2 Crimp Connector Hand Tools and Tool Kits

DX Engineering Ultra-Grip 2 Crimp Connector Hand Tools and Tool Kits are ready to help you make professional quality crimped coaxial cable assemblies, Powerpole® connections and many other popular-size wire terminations. Ultra-Grip 2 Crimp Tools are precision made heavy-duty commercial grade hand crimp tools. They are multi-purpose interchangeable-die tools made from high-quality carbon steel with a tough black-oxide finish for corrosion resistance and durability. These easy-to-use ratcheting crimpers are ergonomically shaped to produce extra manual power, with soft non-slip dual-color thermoplastic rubber grips for comfortable and positive connector crimping results. Ultra-Grip 2's integral ratcheting mechanism lets you make 'semi-automatic' perfect crimps, again and again, with any of the available dies for RF connectors and wire terminations. One of or DXE-UT-CRMP2 Crimp Tools is supplied with the DXE-UT-DIE-8U Crimp Die for RG-8U/213/LMR-400/400MAX size cable. The included 2.5 mm Allen wrench is used to change to one of the other optional die sets. Other sets cover the most popular sizes of coaxial cables with ten different Amphenol Connex crimp connectors in UHF Male/PL-259, Type N, BNC; Powerpole® connector sizes 15, 30 and 45 Ampere connectors, Molex connector pins, insulated crimp type connectors for 22-18/16-14/12-10 AWG and un-insulated crimp type connectors for 20-18/16-14/12-10 and 8 AWG. Our crimp tool and dies are compatible with major brand crimp tool manufacturers. DX Engineering Ultra-Grip 2 Crimp Connector Hand Tool Kits, model DXE-UT-KIT-CRMP2, provides a handsome, convenient carrying case furnished with the Ultra-Grip 2 Crimp Connector Hand Tool, cable shears, braid trimming tool and ALL FIVE CRIMP DIE SETS with a precut foam insert providing a home for each tool and die set. Coaxial cable connector crimping dies are cut to enable crimping both the ferrule and the center pin. DXE-UT-CRMP2 Crimp Tools, sold individually, include one set of DXE-UT-DIE-8U Crimp Dies for RG-8U/213/LMR-400 size cable. DXE-UT-KIT-CRMP2 Complete Kits contain: * DXE-UT-CRMP2 Ultra-Grip 2 Crimp Connector Hand Tool * DXE-UT-DIE-8U Crimp Die works on connectors for RG-8U/213/LMR-400 size cable * DXE-UT-DIE-8X Crimp Die works on connectors for RG-8X/LMR-240 AND RG-58/LMR-195 size cable * DXE-UT-DIE-PP Crimp Die for Powerpole® 15, 30, 45A contacts and Molex connector pins * DXE-UT-DIE-INS for insulated crimp style terminals 22-18/15-14/12-10 AWG * DXE-UT-DIE-UNIS for uninsulated crimp style terminals 20-28/26-24/12-10/8 AWG * CNL-911 Coaxial cable shears * DXE-170M Precision braid trimmers * 2.5 mm Allen Wrench * DXE-CRIMP-CASE Custom Tool Case Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Here is a link to a "how-to" video about using DX Engineering Cable Prep and Crimp Tools for Crimp Connectors by Randy, K7AGE: https://youtu.be/T6sYL_eJFaQ Not only are these DX Engineering Ultra-Grip 2 Crimp Connector Hand Tools and Tool Kits perfect for helping you make quality crimps and keeping track of your tools, but they also make it easy for you to duplicate quality crimps every time.

4.87 out of 5 stars ( 128 )

$40.99

—

$249.99

DX Engineering Coaxial Cable Grippers

DX Engineering Coaxial Cable Grippers are a great new way to hold coaxial cable firmly, while you prepare it for connectors. This pair of innovative tools was especially designed to provide a dramatically improved grip on DXE-8U, DXE-400MAX, DXE-11U, DXE-213U, standard RG-8 or other RG-8U size (0.405 in. nominal) coaxial cables. Our cable grippers are ideal for use with the DXE-UT-8213 Coaxial Cable Preparation Tool and the DXE-UT-80P and DXE-UT-80N Connector Installation Tools for two-piece solder-on PL-259 and Type N Connectors. On the outside of these tools their bumpy finish helps you maintain a sure grip on the coaxial cable being prepared. Inside, their grooved surfaces grab the coaxial cable safely and allow a sure, non-slip grip every time. The two halves of these tools fit together with hinges and a strong steel spring that aids in grip and alignment. These patent pending red DXE-CGH-8U cable grippers are custom made to fit around and help you hold RG-8U size coaxial cable (about 0.405 in. outside diameter) when using a wide variety of cable and connector tools as well as when soldering connectors. They are also excellent to use when installing crimp connectors. Our green patent pending DXE-CGH-8X cable gripper is excellent for gripping DXE-8X, RG-58 or any similar (about 0.240 in. outside diameter) cables. It's also a perfect match for our DXE-UT-808X cable stripper and DXE-UT-80P and DXE-UT-80N Connector Installation Tools. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Make it easy to hold the coax while you are preparing it for and installing connectors. Order these DX Engineering Coaxial Cable Grippers today and get a grip… on your coaxial cable!

4.74 out of 5 stars ( 43 )

$16.99

DX Engineering PL-259 Connector Assembly Tools

DX Engineering PL-259 Connector Assembly Tools are designed for threading solder-type PL-259 connector sleeves onto the vinyl jacket of RG-8/U, RG-213/U and other similar-sized 0.405 nominal diameter cables. First, properly prepare the coaxial cable and then place the threaded sleeve of the PL-259 connector over the end of the coaxial cable. Start the coaxial cable end into the body of the connector and make sure that all of the strands of the center conductor of the cable are inserted into the center pin. Use these patented* DX Engineering PL-259 connector assembly tools and thread the connector body onto the stripped cable end. Tighten them until the PL-259 connector is fully seated on the coaxial cable. A visual guide at the end allows for easy viewing of the cable center conductor for proper depth installation. When the PL-259 connector is fully seated on the coaxial cable, remove the tool from the assembly. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For a perfect and easy connector installation every time, order DX Engineering PL-259 Connector Assembly Tools! *US Patent # 8,701,278

4.94 out of 5 stars ( 17 )

$38.99

DX Engineering Coaxial Connector Crimp Rings

DX Engineering Coaxial Connector Crimp Rings come in packs of 10, so they will always be handy when you lose one, step on one, or otherwise find yourself short on crimp rings. These parts are a critical component for crimp shield connector assembly. Choose your part number based on cable size type: CRIMP240RING fits LMR-240 and 8X connectors CRIMP400RING fits LMR-400, 8U, 213U and 400MAX PL-259/UHF male connectors. If you use crimp coaxial connectors, you never want to be caught without enough crimp rings! Order DX Engineering Coaxial Connector Crimp Rings now so you will always have them on hand.

Not Yet Reviewed

$9.99

—

$10.99

DX Engineering Next Generation Crimp/Solder 8U PL-259 Connectors

DX Engineering proudly announces our new, ultra-high quality, PL-259 connector that is so different from previous designs that we have a Patent**! DX Engineering Next Generation Crimp/Solder 8U UHF Male Connectors are now available to build your custom coaxial cable assemblies. Engineering studies have confirmed that the absolute best RF connections for double-shielded cables like LMR-400 and DXE-400MAX are made by crimping the shield, not soldering. However, most PL-259 crimped center pins aren't large enough and don't have enough contact area, which affects reliability. DX Engineering has solved those issues with these custom-designed connectors that we introduced on DX Engineering DX Series Coaxial Cable Assemblies. These PL-259s have soldered center pins that are full length and full diameter, so they connect properly, even with worn SO-239s. DX Engineering Next Generation PL-259CS8U series connectors achieve exceptional RF performance and power handling with these features: * All silver-plated brass shell and body * Silver-plated center pin securely mounted in PTFE dielectric * Center pin accepts large conductors and scalloped-tip allows generous solder flow * Crimped shield connection provides maximum reliability for all cables * Deep, double-knurled threaded shells for secure finger tightening * Fits all RG-8U size cables with center conductors up to 10 AWG including DXE-400MAX and LMR-400 as well as RG-213U, RG-11U and many others, including Belden 7810A, 8214, 8267 and 8237, 9913 and 9913F7. * Available in packages of 6, 12 or 24 connectors NOTE: DX Engineering offers reasonably priced, professional grade cable prep and connector crimping tools for an entire range of cables and connectors. Click "More Details" and the "Suggested Parts" tab to see available related products. Now you don't have to use the same old PL-259s. These advanced-technology PL-259 connectors let you build the highest quality coaxial cable assemblies. We designed them to be strong and lightweight and they represent a landmark improvement over decades-old, unchanged connector designs. This time, new IS better! Order DX Engineering Next Generation Crimp/Solder 8U UHF Male Connectors today and take advantage of DX Engineering innovations in RF connectivity! **U.S. Patent D745849

4.95 out of 5 stars ( 234 )

$39.99

—

$114.99

DX Engineering Cable Mount Crimp/Solder SO-239 Coaxial Connectors

DX Engineering Cable Mount Crimp/Solder SO-239 Coaxial Connectors provide dependable performance for HF, VHF, and UHF applications. Each connector features a nickel-plated body and ferrule for durability and corrosion resistance, a gold-plated solder center pin, and a crimp-style shield termination. The PTFE dielectric ensures very low RF loss and exceptional electrical breakdown strength, making these connectors the preferred choice for many RF applications. Available for RG-8X/LMR®-240 and RG-8U/LMR®-400 cables, these connectors will let you connect two cables together with no adapters.

Not Yet Reviewed

$11.99

—

$29.99

Amphenol RF 31-4427 BNC Male Coaxial Connectors

Amphenol RF 31-4427 BNC Male Coaxial Connectors are high-quality 50 ohm BNC plugs that fit RG-400, RG-142 and DXE-58AU coaxial cables. These silver plated brass connectors are installed with a soldered gold plated brass center pin and the shield is crimped with the supplied silver plated copper ferrule. They have a PTFE dielectric and a silicone rubber internal gasket. DX Engineering offers the excellent Amphenol RF 31-4427 BNC Male Coaxial Connectors in a package of two.

Not Yet Reviewed

$37.99

DX Engineering Coaxial Connectors

The DX Engineering Coaxial Connectors shown here include two-part, silver-plated PL-259 and Type-N connectors designed to be crimped or soldered to the shield and soldered to the center conductor. These connectors deliver excellent performance for HF, VHF, and UHF applications. DX Engineering's PL-259 and Type-N connectors feature silver-plated brass throughout the outer and inner conductors and use PTFE dielectric—the best RF insulator—for very low loss and high electrical breakdown strength. Also available are DX Engineering Silver-Plated Reducers, which adapt standard solder-type PL-259 and Type-N connectors for use with single-shield RG-8X and RG-58U coaxial cables. While many types and grades of coaxial RF connectors are offered on the market, DX Engineering provides only top-quality connectors with silver-plated brass bodies and PTFE dielectric. These two-part solder-style connectors fit RG-213, RG-8U, RG-8X/LMR240 and other standard 0.405 in. single-braid shield coaxial cables intended for soldering*—but not 400MAX or LMR-400 double-shield cables. These solder-shield and solder-center connectors are the preferred choice for many Amateur Radio operators installing single-braid shield coaxial cables. Order your DX Engineering Coaxial Connectors and Reducers today! *NOTE: To prevent noise issues, modern engineering practice has determined that double shield cables that have one foil and one braid should not be soldered to the braid, including DXE-400MAX and LMR-400 style cables. Those cables should be terminated with crimp shield or clamp shield style connectors, also available from DX Engineering.

4.94 out of 5 stars ( 116 )

$11.99

—

$43.99

DX Engineering Bead Choke Standoff Kits

DX Engineering Bead Choke Standoff Kits bring a practical solution to a serious problem when ferrite chokes are placed directly onto the metal boom at the feedpoint of beam antennas. A number of Amateur Radio operators and antenna engineers have known for years about the superior choking function of many ferrite toroids beads placed directly on the coaxial cable, as compared to standard feedpoint baluns. A more recent revelation is that the proximity of ferrite beads on coax taped to the aluminum boom of the antenna drastically reduces their effectiveness. DX Engineering Bead Choke Standoff Kits are mounting systems, made of fiberglass or acetyl standoff rods (color varies), PVC carriers and stainless steel hardware, available in four versions. Two sizes of PVC cradle tubes handle two different types of RF bead chokes; 3/4 inch outside diameter (OD) ferrite beads on RG-400 size cable, and 1 inch OD ferrite beads on RG-213 size 0.405 in. coax cable. Each are offered with two different boom size clamps, 2 inch OD and 3 inch OD. Bead Choke Standoff Kits simply hold an RF bead choke and feedline 4 inches away from the metal beam antenna boom (or 4 inches away from the metal mast for a dipole). They maintain the optimal choking performance of ferrite beads on coax. Using DX Engineering Bead Choke Standoff Kits, ferrite bead chokes function at peak performance for these key results: • Prevent feedline radiation of RF • Preserve current balance for proper beam antenna pattern • Prevent feedline shield exterior collected noise and signals from entering the antenna and interior of the feedline, resulting in lower noise floor and enhanced reception The absolute superiority of RF chokes made of many beads on the feedline, over the traditional enclosure balun, is becoming better understood in Amateur Radio. They achieve the best possible RF isolation of the feedline from the antenna and provide completely balanced currents at the feedpoint. Plus, they provide quieter reception with reduction of common-mode noise. Keeping Bead RF Chokes away from metal preserves the optimal function of this method of antenna feedpoint current balance and isolation. This mechanical requirement is simple and practical with DX Engineering Bead Choke Standoff Kits.

5.0 out of 5 stars ( 3 )

$52.79

—

$65.99

DX Engineering UT-KIT4 Complete Coax Cable Tool Kits

DX Engineering DXE-UT-KIT4 Complete Coax Cable Tool Kits are cost-saving tool kits contained in a handsome, convenient carrying case. DXE-UT-KIT4 tool kits are designed to enable fast, easy installation of soldered PL-259 and Type N connectors on only single shield cables including RG-8U, RG-213 and RG-11U. These kits are furnished with our high-quality DX Engineering coaxial cable prep tools and accessories. Their lockable enclosure is fitted with a precut foam insert with a slot for each tool. Not only are these DX Engineering Complete Coax Cable Tool Kits perfect for helping you keep track of your DX Engineering tools, but they also make it easy for you to carry them from job to job. DXE-UT-KIT4 includes: - DXE-UT-8213* - Stripping tool for RG-213 or RG-8 size cable - DXE-UT-808X - Stripping tool for RG-8/X size cable - DXE-CGH-8U - Hinged Coaxial Cable Gripping Tool for RG-213 or RG-8 - DXE-CGH-8X - Hinged Coaxial Cable Gripping Tool for 8X sized cable - DXE-UT-80P - PL-259 assembly tool, (US Pat. 8,701,278) - DXE-UT-80N - Two-piece Type N connector assembly tool, (US Pat. 8,701,278 B2) - CNL-911 - Coaxial cable shears - DXE-170M - Precision braid trimmers - DXE-UT-RB-HD - Heavy duty stripping tool replacement blades - 7/64" Allen Wrench - Used for replacing the tool blades - DXE-UT-CASE - Custom made carry case with foam insert fitted with a precut foam insert with a specific position for each tool Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Whether you are a communications professional who prepares coaxial cables frequently or a Radio Amateur who likes the occasional job done right and easily, these DX Engineering Complete Coax Cable Tool Kits will make single shield coaxial cable preparation a snap. *IMPORTANT: The UT-8213 Prep Tool is NOT intended for use on dual shield coaxial cables including DXE-400MAX and LMR-400 series. Those cables require crimped shield connectors with different stripping dimension. For dual shield cables use the DXE-UT-405C-P1 Cable Prep Tool for DXE-PL259CS8U-6 Next Generation PL-259, or the DXE-UT-405C-N1 Cable Prep Tool for Type N model 172102H243. See the DXE-UT-KIT-CC1.

4.13 out of 5 stars ( 8 )

$349.99

DX Engineering DXE-8U-PREP-P Coax Cable Prep Tool Combos

DX Engineering DXE-8U-PREP-P Coax Cable Prep Tool Combos pair two of our most popular prep tools in one convenient package! Together for your convenience, here are the DXE-UT-8213 and the DXE-CGH-8U. DX Engineering UT-8213 cable strippers are the preferred method for preparing only single shield*, 0.405 in. size coaxial cables, including RG-8U, RG-213 and RG-11U, for standard PL-259 connectors with soldered center and shield. These strippers easily remove the outer jacket, shield and dielectric to prepare for soldered PL-259 coaxial cable connectors, including DXE-PL259-6 and AML-83-1SP-6. Included with the DXE-UT-8213 in this Prep Tool Combo is our DXE-CGH-8U hinged cable gripper; it is the perfect companion tool! These grippers allow you to have a much larger surface to hold onto while the gripper itself securely holds your cable for easy trimming. Please check the "Kit/Combo Contents" tab for more detailed individual-item information. *IMPORTANT: The UT-8213 Prep Tool is NOT intended for use on dual shield coaxial cables including DXE-400MAX and LMR-400 series. Those cables require crimped shield connectors with different stripping dimension. For dual shield cables use the DXE-UT-405C-P1 Cable Prep Tool for DXE-PL259CS8U-6 Next Generation PL-259, or the DXE-UT-405C-N1 Cable Prep Tool for Type N connector model 172102H243. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Make coax cable preparation for soldered PL-259s so much easier with the DXE-UT-8213 and the DXE-CGH-8U. Order them together in the DX Engineering DXE-8U-PREP-P Coax Cable Prep Tool Combo and get a better grip on coax preparation!

5.0 out of 5 stars ( 5 )

$92.98

DX Engineering Crimp Connector Tool Cases

If you have collected some or all of our Crimp Connector Tools and Dies, you can store them in one of these DX Engineering Crimp Connector Tool Cases. They will hold your crimp tools with a fitted, precut foam insert that has a specific position for each tool, die and your connectors. They are perfect for keeping everything together, ready to go! DX Engineering Crimp Connector Tool Cases can accommodate: -- DXE-UT-CRIMP Rugged Crimp Tool -- DXE-UT-DIE-8U Crimp Die for RG-8U/LMR-400 size cable -- DXE-UT-DIE-8X Crimp Die for RG-8X/LMR-240 size cable -- DXE-UT-DIE-PP Crimp Die for Powerpole® 15, 30, 45A contact -- CNL-911 Coaxial cable shears -- DXE-170M Precision braid trimmers -- 2.5 mm Allen wrench -- Extra compartment for connectors Note: These tools are not included with this case. For a complete kit with the tools and the case, order DXE-UT-KIT-CRIMP. Crimp connectors are sold separately.

5.0 out of 5 stars ( 2 )

$41.99

DX Engineering UT-KIT3 Basic Coax Cable Tool Kits

DX Engineering DXE-UT-KIT3 Basic Coax Cable Tool Kits are cost-saving tool kits contained in a handsome, convenient carrying case. They are designed to enable fast, easy installation of soldered PL-259 connectors on single shield cables including RG-8U, RG-213 and RG-11U. These kits are furnished with our high-quality DX Engineering coaxial cable prep tools and accessories. They feature a rugged, lockable enclosure that is fitted with a precut foam insert with a home for each tool. Not only are these DX Engineering Basic Coax Cable Tool Kits perfect for helping you keep track of your DX Engineering coaxial tools, but they also make it easy for you to carry them from job to job. UT-KIT3 includes: - DXE-UT-8213* - Stripping tool for RG-213 or RG-8 size cable - DXE-CG-8U - Coaxial Cable Gripping Tool - DXE-UT-80P - PL-259 assembly tool, (US Pat. 8,701,278 B2) - CNL-911 - Coaxial cable shears - DXE-UT-CASE - Custom made carry case with foam insert fitted with a precut foam insert with a specific position for each tool Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Whether you are a communications professional who prepares coaxial cables frequently or a Radio Amateur who likes the occasional job done right and easily, these DX Engineering Basic Coax Cable Tool Kits will make coax preparation for soldered PL-259s a snap! *IMPORTANT: The UT-8213 Prep Tool is NOT intended for use on dual shield coaxial cables including DXE-400MAX and LMR-400 series. Those cables require crimped shield connectors with different stripping dimension. For dual shield cables use the DXE-UT-405C-P1 Cable Prep Tool for DXE-PL259CS8U-6 Next Generation PL-259, or the DXE-UT-405C-N1 Cable Prep Tool for Type N model 172102H243. See the DXE-UT-KIT-CC1.

5.0 out of 5 stars ( 3 )

$181.99

Times Microwave Systems® WSB Series Weather Seal Boots

Times Microwave Systems® WSB Series Weather Seal Boots work with most of the popular Times Microwave EZ crimp connectors. These boots are available for LMR®-195, LMR®-200, LMR®-240/DXE-8X and equivalents, 0.405 in. diameter coax such as LMR®-400, RG-8, DXE-400Max, DXE-213 and equivalent, and LMR®-600 size coax. * Use TMV-WSB-195-200 for LMR®-195 or LMR®-200 * Use TMV-WSB-240 for LMR®-240 and equivalent * Use TMV-WSB-400 for LMR®-400 and equivalent * Use TMV-WSB-600 for LMR®-600 and equivalent These soft, silicone-boot weatherproofing kits replace older weatherproofing methods. They require no heat and only simple and easy hand assembly for valuable time saving in the field. Once installed, the boot provides strain relief to the crimp connection by reducing flexure. WSB kits are IP67 rated and both RoHS and REACH Compliant. Supplied in a convenient 10 pack, WSB kits contain four pouches of silicone lubricant to better facilitate installation of the boot. WSB Series weather seals: * Are ISO 9001 Certified * Provide combination weather seal and strain relief * Eliminate the need for a heat gun to shrink the standard heat shrink sleeve * Fit the most popular Times Microwave EZ connectors * Are IP-67 rated for water ingress Note: Whenever DX Engineering "Documentation" is available, please click for the associated files for additional product information. Weather is the worst enemy of your feedline. Order Times Microwave Systems® WSB Series Weather Seal Boots and give your coax the "seal" of approval! LMR® is a registered trademark of Times Microwave Systems®.

4.75 out of 5 stars ( 4 )

$30.95

DX Engineering Coaxial Cable Prep Tools for Crimp Connectors

DX Engineering Coaxial Cable Prep Tools for Crimp Connectors are an easy way to prepare cable ends for RF crimp connectors. These are the tools to use for dual shield cables that require crimp connectors, as well as on single shield cables when you want to use crimp connectors. - Please CLICK or TAP on the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation.

4.56 out of 5 stars ( 178 )

$44.99

—

$319.99

DX Engineering Crimp Tool Dies

DX Engineering Crimp Tool Dies are interchangeable dies designed for use with the DXE-UT-CRMP2 Crimp Tools and the legacy DXE-UT-CRIMP tool. Covering most popular sizes of coaxial cables, three DX Engineering Crimp Tool Dies handle ten different crimp connectors in BNC, Type N, and UHF Male/PL-259 and three Powerpole® connector sizes. Two additional interchangeable dies handle crimping Molex connector pins, insulated crimp type connectors for 22-18/16-14/12-10 AWG and uninsulated crimp type connectors for 20-18/16-14/12-10 and 8 AWG You can order your Crimp Tool Dies separately here, or all together in the models Ultra-Grip 2 Crimp Connector Hand Tools and Tool Kits, model DXE-UT-KIT-CRMP2 DX Engineering Coax and Powerpole® Crimp Tool Kits. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Order our DX Engineering Crimp Tool Dies and make wire and cable assembly much easier!

4.79 out of 5 stars ( 53 )

$31.99

Times Microwave Systems® Mid-span Coaxial Grounding Kits

Times Microwave Systems Mid-span Coaxial Grounding Kits let you ground the coaxial shield to any convenient location with a ground lug. This includes most grounding clamps, plates and fixtures. For towers, an additional tower leg clamp is usually required. After stripping the outer jacket with a mid-span stripping tool, a pre-formed metal strap is applied to the braid/shield and tightened down. This strap is then electrically and mechanically connected to the ground source with a ground lead assembly, providing an excellent ground for the shield. These mid-span shield-grounding kits include: (1) Pre-formed tinned copper ground strap (1) Ground lead assembly (2) 1/4 in. brass lock-washers (2) 1/4 in. brass nuts (1) Roll 2-1/2 in. x 24 in. (610mm) butyl mastic (1) Roll 3/4 in. x 20 ft. (6.1m) PVC tape (1) Heat shrink tube (1) Field-crimp 3/8 in. 2-hole lug (2) 3/8 in. x 1-1/4 in. slotted bolts (2) 3/8 in. lock-washers (2) 3/8 in. nuts (2) 3/8 in. flat-washers (1) Detailed assembly instructions Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Their included weatherproofing materials provide long-lasting environmental protection to help maintain a reliable ground for your coax. Shop DX Engineering for Times Microwave Systems Mid-span Coaxial Grounding Kits! LMR® is a registered trademark of Times Microwave Systems.

5.0 out of 5 stars ( 4 )

$45.99

COMTEK Current Feedline Chokes

The updated COMTEK CFC-50A 50 ohm Feedline Chokes consist of 75 heavy-duty mix-31 RF choke beads on a length of RG400 PTFE coax terminated at both ends with silver-plated PTFE PL-259/UHF male connectors and the correct length of heat-shrink tubing. COMTEK Current Feedline Chokes ensure that stray RF does not flow on the outside shield of your feedlines. They are typically installed at the antenna feedpoint connection. They may also be used where a long run of feedline leaves a remote antenna switch or a tower. They are also very effective at the shack end of a long run of on-the-ground or above-ground coaxial feedline, to block unwanted RF signals and noise picked up on the shield. These chokes provide excellent common mode impedance and handle up to 5 kW from 1.8 to 54 MHz. These chokes are assembled except for the tubing needs to be installed and heat-shrinked after the choke is positioned as it will be installed.

4.64 out of 5 stars ( 14 )

$131.49

Times Microwave Systems® Coaxial Cable Hoisting Grips

Times Microwave Systems Coaxial Cable Hoisting Grips provide an effective method for lifting coaxial cable to the top of a structure, where it may then be tied off to support the cable's weight. Cable hoisting grips will not crush or deform the cable being lifted, but easily release the cable when desired. They are available in several sizes to hoist a multitude of cable types. Don't risk dropping your coax or using destructive methods to loft it. Order Times Microwave Systems Coaxial Cable Hoisting Grips from DX Engineering and hoist your cable the easy way! LMR® is a registered trademark of Times Microwave Systems.

4.5 out of 5 stars ( 4 )

$28.99

DX Engineering Ferrite

DX Engineering Ferrites are partially magnetic metal and ceramic mixes available in a variety of forms, including toroid core, bead type and plastic-covered split-bead ferrite called snap-beads. They are used in a myriad of RF suppression applications to mitigate RFI (radio frequency interference) as well as to reduce pulse and other types of RF noise interference. Special ferrites are used for experimentation and electronic circuit building and for making transformers, RF chokes and antenna baluns. The variations of magnetic and non-magnetic metals and non-metal ceramics used to make ferrites are called "Mixes" and each has different radio frequency properties or ranges. Therefore, different mix number ferrites are typically used for different applications within those ranges, determined by decades of experiments by engineers and applications by hams. Each Mix has been assigned a color code to help identify the ferrite, so numerical labeling is not used on the metal. Color coded ferrite can be identified long after the numbered package is discarded or has disintegrated with time. How do they work? Simply use snap-on beads on a cable or wire. An even more effective choke takes a few to several turns of a wire or cable through and around a ferrite snap-on bead or toroid core. This mitigates RFI to, or from, the connected RF noise producing or noise affected electronic device. The results can be very surprising. Solving noise and RFI can be frustrating. Due to the nature of RF and noise interference suppression; the techniques of appropriate use of ferrites can take a bit of trial and error, but are often the best solution for a difficult problem. Use DX Engineering Ferrite for an incredible range of electronic circuits, noise abatement and RF suppression projects. The details of DX Engineering Ferrite mixes and types appear in each product description. Sizes and applications are discussed in "More Details" and in the literature available at the "Documentation" tab of each of these products.

4.88 out of 5 stars ( 198 )

$34.99

—

$46.99

DX Engineering Partsbox Storage Cases

DX Engineering Partsbox Storage Cases are almost self- explanatory. They're very cool, handy plastic cases with removable and adjustable dividers, lids with clasps, and carry handles. The cases are big enough that they can be used for parts and small hand tools. With the lid closed, parts and tools stay in their customized compartments when carried. And the best part—they can be used individually or as part of a system, because they fit right into the sliding shelves of the DX Engineering Storage Cabinets! Partsbox Cases are 13 1/2 x 2 1/8 x 9 1/2 in. (WHD). DX Engineering has brought to our market this great new system of Storage Cases that fit perfectly into the Storage Cabinets. We also offer Partsbox cases with a special selection of coaxial connectors or Anderson PowerPole connectors. See the Related Parts links and the Suggested Parts tab in the More Details page. DX Engineering Partsbox Storage Cases are the perfect answer for a well-organized workbench and ham radio shack. Order yours from DX Engineering.

4.33 out of 5 stars ( 3 )

$143.94

  • 1
  • Page 1 of 1