Instruction Sheets for Part Number SBM-FUSER-6-KIT
SOTAbeams Fuser 6 DC Distribution Boxes
DC Outlet Panel, Fuser-6 Fused PowerPole® Connector Box Kit, plus Enclosure, Each
See More Specifications
Estimated Ship Date: Tomorrow Would you rather pick it up?
Overview
Brand:
Manufacturer's Part Number:
FUSER-6-KIT
Part Type:
Product Line:
DXE Part Number:
SBM-FUSER-6-KIT
High Current Maximum:
25 A
High Current Power Poles:
Yes
High Current Power Pole Outputs:
2
High Current Binding Posts:
No
Low Current Output On/Off Switch:
No
Low Current Power Poles:
Yes
Low Current Power Pole Outputs:
3
Low Current Binding Posts:
No
Voltage Monitor:
No
Audible Voltage Alarm:
No
Built-In Voltmeter:
No
Programmable Fault Thresholds:
No
Input Cable Installed:
No
Fused Input:
Yes
Individually Fused Outputs:
Yes
Combined Fused Outputs:
No
Fuses Included:
Yes
Outlet Panel Width:
5.000 in.
Outlet Panel Height:
2.750 in.
Outlet Panel Depth:
1.600 in.
Outlet Panel Weight:
0.30 lbs.
Quantity:
Sold as a kit.
Notes:
Instructions may be downloaded from SOTAbeams.
SOTAbeams Fuser 6 DC Distribution Boxes
SOTAbeams Fuser 6 DC Distribution Boxes are the lightest PowerPole® distribution boxes… by far!
SOTABEAMS PowerPole® Fuser-6 boxes make light work of connecting five accessories to your power source (they have one input and 5 outputs). All of the connectors are individually fused. In a typical shack you might have a 100 Watt HF radio, a 50 watt 2m FM radio, an antenna tuner and a QRP rig all connected to your Fuser-6 - and still have a spare connector!
Fuser-6 boxes are supplied with three 25 Amp and three 5 Amp fuses. Standard automotive blade fuses make replacement easy - these are widely available with values from 1 to 30 Amps. Fuser-6 units incorporate a polarity warning system; lights GREEN for CORRECT and RED for REVERSE. It's handy when you have a battery connected to the system to help avoid damage to your equipment if you accidentally get the battery connections reversed.
Fuser-6 internal circuitry is rated at 25 Amps (30 Amp surge); no mean feat for a PCB design. To achieve SOTAbeams had to use a special PCB with double weight copper. They also use a clever design to further improve the current handling: ultra-wide copper tracks are used on both sides of the board. The boards are then roller tinned (on both sides) to reduce the resistance and handle heat even better. They use plated through holes, carefully located to ensure an even current distribution between each face of the board. Of course, Fuser-6 boards use genuine Anderson PCB contacts for lower contact resistance and improved reliability.
NOTE: For best kit results use a soldering iron of at least 50 Watts. Additional flux is also helpful to ensure a good result.
Additional details:
* 25 Amps continuous, 30 Amps surge (adjacent connectors)
* 1 input, 5 outputs
* Power Bus resistance typically less than 1.80 milliohms end to end
* Weight 135 g (less than 5 oz.)
* W 68 x L 130 x H 40 mm (excluding connectors) 2.75 x 5 x 1.6 in.
Whether you use one for your go kit, QRP setup or for use in the shack, these SOTAbeams Fuser 6 DC Distribution Boxes from DX Engineering are a handy DC power solution.
Documentation
Loading...
Applications
Loading...
Loading...
Some parts are not legal for use in California or other states with similar laws / regulations
Modal Header
Call To Order
This is a custom order part. You can order this part by Contacting Us.
Email this page