Filters
AALogic Parts and Accessories
AALogic MCI-102 Mic Control Interfaces
AA Logic MCI-102 Mic Control Interfaces allow you to use one microphone on two different radios, even if those radios are from different manufacturers. The MCI-102 also lets you use the same foot switch and amplifier key line on either radio, with no cable juggling, just the flip of a switch. The front panel features four switches: Power, Key Enable, Radio Select and Mic Select, LEDs to indicate status of the MCI-102 at a glance, as well as an RJ-45 and 8-pin foster connection. The rear panel features a pair of 8-pin foster connections, a 1/4-inch mono jack for a foot switch, a 1/8th inch stereo jack for a boom mic, and RCA connectors for key lines and ALC lines, common to an amplifier, and lines to each of the radios. Power is supplied via the included power adapter. Additional Feature and Specifications: • Microphone routing: M1 to Radio 1 or Radio 2 (R1/R2) • Boom microphone input, 3.5mm TRS (powered via selected tradio) • Foot switch input, 1/4″ TS • Switchable external amp keying • ALC routing or remote antenna switch control • Compatible with ICOM/Kenwood/Yaesu/Alinco (internal jumper configuration) • Cross radio compatible (ICOM Mic/Kenwood Radio, etc) • Full function MIC 1 to Radio 1 Only • DPDT control switch (SPDT PTT Control, SPDT External R1/R2 Control) • PTT switchable load (high voltage open collector) • Single switch changes inputs to selected radio • KEY enable switch allows operation with or without connected external amplifier
( 1 )
$290.00
AALogic Microphone Adapter Cables
AALogic Microphone Adapter Cables are what connect the AA Logic MCI-102 to your radio. Available in 8-pin Foster to RJ45 and 8-pin Foster to 8-pin Foster and in two different lengths, each cable allows for connection between the MCI-102 and the radio. There is also an XLR to 3.5mm TRS cable if you are using a microphone that has an XLR connector on it. Microphone pinout is determined by jumper settings inside the MCI-102. Please check the manual for details. The Foster to RJ45 and Foster to Foster cables are available in two lengths, 39.37 inches (1 meter) and 78.84 inches (2 meters). The XLR to 3.5mm cable is 76" long. At least one cable is required for each radio. LGA-CBL-F45-Y1M 1 meter long 8 Pin Foster to RJ45 modular connector (for radios that use RJ45 connectors) LGA-CBL-F45-Y2M 2 meter long 8-pin Foster to RJ45 modular connection (for radios that use RJ45 connectors) LGA-CBL-FF-1M 1 meter long 8-pin Foster to 8-pin Foster connection (for radios that use an 8-pin round connector) LGA-CBL-FF-2M 2 meter long 8-pin Foster to 8-pin Foster connection (for radios that use an 8-pin round connector) LGA-CBL-XLR-35 2 meter long 3-pin XLR to 3.5mm TRS (for attaching a mic with an XLR connector to the MCI-102.
Not Yet Reviewed
$30.00
—
$60.00
AALogic Rotator Controller Plug and Play Cables
AALogic Rotator Controller Plug and Play Cables allow you to connect your existing cable that is terminated in the connector for the controller that came with the Rotator. These one-foot cables feature a terminal block that matches the connector on the DTC-100 combined with a mating connector for the Yaesu or HyGain rotator, meaning you can use the existing cable without removing the existing connector. These cables simplify the setup and configuration of your AALogic DTC-100. The LGA-CBL-Y6 is for the Yaesu lineup of the G450/G800/G1000/G2800 Rotators The LGA-CBL-H6 is for HyGain rotators.
Not Yet Reviewed
$40.00
—
$70.00
AALogic USB to TTL Cables
AALogic USB to TTL Cables provide a way to connect the AALogic DTC-100 to a computer for computerized control of the rotator. Featuring a USB port on one end and a 3.5mm TRS plug on the other end, this cable assembly provides a way to connect the DTC-100 to a computer that is running in the shack.
Not Yet Reviewed
$30.00
AALogic DTC-100 Version 6 Rotator Controllers
AALogic DTC-100 Version 6 Rotator Controllers are compatible with digital pulsed feedback rotators such as the Orion 2800, the Alfa SPID, The HyGain DCU-3 compatible rotators, and the DX Engineering RT4500HD. Not only will the DTC-100-V6 work with rotators that have digital pulsed feedback, it will also work with rotators that utilize resistive sensors to determine the orientation of the rotator, Rotators that utilize resistive sensors include Yaesu's G450/G800/G1000/G2800 Series rotators as well as all HyGain Rotators. The DTC-100-V6 also allows the user to set soft rotational limits for both Yaesu and HyGain rotators that incorporate mechanical limits to help keep the rotator from travelling to the mechanical stop. A full color 5-inch touch screen display fills the front panel of the DTC-100-V6. The DTC-100-V6 supports extensive calibration options when it comes to rotators that don't have 'hard limit' switches and even those that do, the user can set soft limits for stopping the rotator before the hard limit switches are set. Once the rotator type has been selected in the calibration screen, the user can set rotation limits for both clockwise and counterclockwise rotation. The configuration of the DTC-100-V6 allows the user to adjust the backlight, the start and stop brake function (needed on HyGain rotators), coast settings, and ramp up and down speeds. These settings allow for control of the rotator as it gets close to the end of its safe rotation, allowing for the rotator to coast to a stop and not jerk to a halt where you want the antenna pointing. Six memories allow the user to set frequently accessed headings to expedite a starting point of the turning the antenna. Memories can also be programmed on an ad hoc basis and not saved to work DX or for some operating event that is outside of the users' normal scope of operation. This allows for flexibility in how the controller is used. The Main operating screen of the DTC-100-V6 provides a graphical representation of where the antenna is facing, saved memories, quick access to the system configuration screen, and controls to manually turn the antenna clockwise and counterclockwise as well as stopping the rotation. The display also shows if the rotator has spun into the overlap zone, and if there is remote control of the DTC-100. The rear panel of the DTC-100-V6 includes an 8-pin terminal block, a 3.5mm TRS jack for an optional RS232TTL adapter, standard IEC-320 connector block, with fuse and power switch. A 6 foot long, 110VAC power cord is included. Also included is the mating connector for the terminal block. If you already have the line to your rotator terminated for the controller that came with your rotator, there are optional cables available for both Yaesu and HyGain rotators that allow the use of cables that are already terminated with the connectors for the vendor supplied rotator controllers and you don't wish to remove the termination to use the DTC-100-V6. Additional Feature and Specifications: • Computer interface for logging programs • Computerized motor control • Auto brake release/engage • Speed ramp up/down for smooth start/stop • Variable coast control • Pinpoint accuracy • Automated calibration for simple installation • Supports pulsed feedback sensors • User ability to set soft limits
Not Yet Reviewed
$750.00
AALogic Ethernet Adapter Modules
AALogic Ethernet Adapter Modules allow for control of your AALogic DTC-100 via ethernet. This arrangement is useful in remote shacks where applications such as PST Rotator or HRD are running on a computer in the remote shack and allowing for remote control of aspects of the station or stations where the operation of the station is handled over a local area network. Once the EAM-100 is connected to power and ethernet, a webpage running on the EAM-100 will allow the selection of an IP address and port for remote connections. The EAM-100 comes with a 12VDC adapter, a 3.5mm TRS cable to connect the EAM-100 to the DTC-100 and a flash drive with users' guides.
Not Yet Reviewed
$150.00
AALogic Voice Recognition Modules
AALogic Voice Recognition Modules allow you to do something that seems like it's straight out of science fiction: Control your AALogic DTC-100 with just the sound of your voice. In addition to being able to control the rotator with your voice, the VRM-100 will also provide audible feedback on the current azimuth of the antenna. The VRM-100 will also allow the user to rotate the antenna by simply providing the heading and the DTC-100 will point the antenna. The VRM-100 also requires no internet connection to function. The package comes with the VRM-100, a built in 3-watt speaker, a power adapter, and a cable to interface the VRM-100 with the DTC-100. The VRM-100 requires between 9 and 12 Vdc and can be powered either by the supplied adapter or a 12Vdc supply in the shack. The front panel features a power LED, power switch, speaker grill, and volume knob. The rea panel features an external speaker jack, a 3.5mm jack for the interface cable and a power jack.
Not Yet Reviewed
$180.00