Availability
DX Engineering Antennas
DX Engineering RR8B-HP Remote Antenna Switches
DX Engineering RR8B-HP Remote Antenna Switches are RF switches designed to have excellent performance on HF through 6 meters. Using 16 custom, sealed, moisture-resistant relays, these Remote Switches provide the best port-to-port isolation available with reliable, long-term performance. RR8B-HP switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, thereby allowing their use in complex antenna phasing and stacking systems. DX Engineering RR8B-HP switches use a removable screw-terminal control cable plug that greatly simplifies installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting-bracket flange and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. O.D. Features of the RR8B-HP Remote Antenna Switches include: * Fully RF shielded with stainless steel mounting bracket and hardware * Best port-to-port isolation available: Over 70 dB isolation below 30 MHz, Over 55 dB isolation below 60 MHz * Loss: Less than 0.1 dB below 60 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Shorted or open selection of unused antenna ports * Sealed 20 ampere, RF-rated relays * Safe 12V DC relay operation * Lightning protection on control lines * External quick-connect plug for control lines * Reliable operation in extreme-weather conditions Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For reliable operation of multiple antennas through the operation of remote switching, order DX Engineering RR8B-HP Remote Antenna Switches to do the job!
( 5 )
$549.99
DX Engineering RR8B-SD Remote Antenna Switches
DX Engineering RR8B-SD Remote Antenna Switches are the highest power handling antenna switches in the DX Engineering RR8 Series. Think of them as Super Duty. They are designed to switch up to 8 coaxial lines in high-power RF systems. RR8B-SD switches use enclosed RF-rated relays with exceptional RF voltage and current capability to provide reliable, long-term performance. DX Engineering RR8B-SD switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, allowing for use in complex antenna phasing and stacking systems. RR8B-SD switches use removable screw-terminal control cable plugs that greatly simplify installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting bracket flange, and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. outside diameter. RR8B-SD Remote Antenna Switches feature: * Fully shielded, high impact thermoplastic enclosure, stainless steel mounting bracket, and hardware * Excellent port isolation; greater than 60 dB at 30 MHz, worst case * Power Rating: Greater than 10 kW in normal amateur operation on all modes when using antennas with less than 2:1 SWR on 30 MHz and below. Greater than 5 kW above 30 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Lightning protection on control lines * Shorted or open selection of unused antenna ports * Custom sealed 30 ampere high-voltage RF relays * Solderless removable plug for easy installation of control line with no disassembly * Safe 12V DC relay operation * Reliable operation in all weather extremes Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For multi-band multi-antenna QRO operation, there is no better remote switch than DX Engineering RR8B-SD Remote Antenna Switches!
( 4 )
$599.99
DX Engineering 4030VA-1 Dual-Band THUNDERBOLT® Vertical Antennas
DX Engineering's Dual-Band THUNDERBOLT® 40/30 Meter Vertical Antennas are high performance dual-band pile-up busters that are tunable to operate with an SWR of 1.5:1 or less across both bands. The maximum power rating ensures solid performance, particularly on CW. Plus, the digital modes are popular on 30 meters. The massive EXTREN® channel insulator supporting the rugged structural grade type 6063-T832 drawn aluminum antenna radiator has over twice the tensile and flexural strength of competitive nylon plastic materials, and they are superior for their RF handling characteristics. Designed with rugged 6063 heat-treated, corrosion-resistant aluminum tubing and stainless steel hardware, these antennas are very durable and attractive. Now, you can have full quarter wave performance on both bands without having to compromise. Of course, another key to performance is a good ground radial system. We recommend 32 radials, 32 ft. long. Fewer radials will work, but with diminished results. These antennas include the antenna element, insulated Extren mounting channel, mounting plate, tilt base, stainless steel hardware, and stainless steel element clamps. See Suggested Parts for additional items that will enhance the performance of your installation. DX Engineering's Dual-Band THUNDERBOLT® 40/30 Meter Vertical Antennas feature: * Full band coverage on 40 and 30 meters with SWR under 1.5:1, with no tuner needed * 40m bandwidth greater than 750 kHz with SWR under 2:1 * Tunable above and below 7 MHz range for MARS and CAP frequencies * Over maximum legal power handling * Optimum 30 ft. overall height * Self-supporting design to withstand 60 mph wind without guying Note: For additional information, please look at the files under the "Documentation" tab.
( 2 )
$609.98
DX Engineering 8040 NVIS Antennas
DX Engineering 8040 NVIS Antennas: Near Vertical Incidence Skywave (NVIS) is a propagation mode which uses high-angle radiation that sends signals almost straight up! They are then reflected back to Earth for very effective short to medium distance communications that works virtually every day and into the evening. NVIS dipoles are almost Omni-directional and their height requirement is for the feedpoint to be at only 15 feet above the ground! These 80 and 40 meter wire antennas work very well with their feedpoint at only 15 feet above the ground, supported by the included mast, or your own non-metallic support. The ropes tied to the wire dipole end-insulators are used as guys for the support mast, and are secured to the ground with four tent pegs. DXE-NVIS-8040S and the DXE-NVIS-8040 antenna kits are complete with everything required; the fiberglass mast (four, 4 ft. sections that extend to 15 ft.), a DX Engineering Maxi-Core® 20 1:1 Balun, model DXE-MC20-1-1T, a balun mounting kit, coax strain relief bracket, antenna wire, insulators, four tent pegs, rope, and a 100 ft. RG-8X coax assembly with PL-259s! The four legs of the antenna, each deployed 90 degrees apart, provide the mast guying. DXE-NVIS-8040SNM and the DXE-NVIS-8040NM antenna kits are exactly the same kits with everything except the 15 ft. fiberglass mast. Use your own non-metallic mast or hang the feedpoint 15 ft. above the ground from the limb of a tree. The DXE-NVIS-8040S and DXE-NVIS-8040SNM are shortened NVIS wire antenna kit version that features loading coils to make the 80 meter dipole legs the same length as the 40 meter dipole legs, 34 ft., so this antenna fits into a square area that is only about 50 ft. by 50 ft. The DXE-NVIS-8040 and DXE-NVIS-8040NM are full size, with 67 ft. wire dipole antenna legs for 80 meters and 34 ft. legs for 40 meters and it fits into a rectangular area approximately 100 ft. by 50 ft. NVIS rarely works at frequencies outside the range of 2 MHz to 10 MHz. The signal must penetrate the D layer of the ionosphere and bounce off the F layer. Signals on frequencies below 2 MHz will not penetrate the D layer; frequencies higher than 10 MHz will not bounce off the F layer at these sharp angles, they penetrate and continue out into space. Regular-height dipoles or vertical antennas have a lower take off angle and your signal may be heard three states away, but not in your own state due to the "skip zone." This skip zone is the area between the maximum ground wave distance and the shortest sky wave distance where no communications are possible. Depending on operating frequencies, antennas, their height above ground and propagation conditions, this skip zone can start at roughly 10 to 20 miles away and extend out to several hundred miles. NVIS mode of operation makes it ideal for in-state and next state communications during disasters or other emergency situations. The military has used NVIS techniques for decades to provide short haul communication with other units on the ground. This is why these antennas are ideal for round-table gatherings with regional ham friends on 40 and 80 meters, day to day and night after night. These antennas are easy to deploy and are great for camping, RVs, QRP, ARES, EMCOMM, State QSO Parties and Parks On The Air (POTA) and any other uses where short range HF operation on 80 or 40 meters is desirable. They are actually pretty stealthy, too! Due to their near vertical radiation, NVIS dipoles are almost Omni-directional. They even have a legal-limit power rating! Remember, Amateur Radio operators look to 80 and 40 meters for short skip NVIS operations. Order DX Engineering 8040 NVIS Antennas and fill in the skip zone!
( 6 )
$533.88
—
$656.86
DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas
DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas are 43 ft. tall, high performance, 160 through 10 meter vertical antennas - designed from the ground up to offer ease of use, reliability and performance! New design and materials technology are used throughout. The patented* and massive SAF-T-TILT™ 3/8 in. thick rugged aluminum base allows easy, safe tilt action without the unsafe removal of mounting hardware -- as with some competitors' antennas! Now - using our ground-mounted vertical, you'll work DX as you never could with a low horizontal-dipole antenna! DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas require a special DX Engineering DXE-UN-43 UNUN with 150 ft. of RG-213 coax feed and your wide-range tuner - OR a automatic tuner at the base of the antenna without the UNUN.. These MBVE-5A verticals feature: * High strength Delrin® thermoplastic insulator that won't crack, splinter, peel or fail from exposure * Rugged structural grade type 6063-T832 drawn aluminum tubing radiator - the best alloy for high-strength, long-lasting antenna applications * New, massive, patented* SAF-T-TILT™ base allows safe raising and lowering of antenna without removal of fastening hardware * The fast taper antenna element provides the lowest wind resistance * Free-standing to 92 mph wind speeds * All Stainless Steel hardware - very durable and attractive MBVE-5A verticals include the antenna element, mounting plate with insulator, exclusive Patent Pending SAF-T-TILT™ Base, stainless steel hardware and clamps. Like any HF vertical, MBVE-5A verticals require a good ground radial system. 32 radials, 65 feet long are recommended. Fewer or shorter radials will work, but with some diminished results. For proper installation, additional materials are needed, but not supplied. You will need: * Mounting pipe--steel pipe that has 2.0 in. O.D. with 0.25 in. wall thickness, 4 ft. long -- standard 1-1/2 in. galvanized water pipe (with its 1.9 in. OD) is fine * Quick-Set or other concrete for mounting pipe installation * Radial wire and wire lugs--must use 14-gauge, stranded copper wire with PVC insulation. A minimum of 20 radials, each 32 feet long, should be used. * Penetrox A -- to ensure good connection between aluminum hardware and in-between aluminum tubing sections * Anti-seize compound, which should be used on the threads of all the stainless steel hardware to prevent galling Consider these new, cost-effective DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas and packages now available for your application: -- DXE-MBVE-5A 43 Ft. Antenna only -- DXE-MBVE-5A-4P Antenna Package with Radial Plate -- DXE-MBVE-5A-4UP Antenna Package with UN-43 UNUN -- DXE-MBVE-5A-4UPR Antenna Package with Radial Plate and UNUN Packages with Radial Plates include two extra hardware kits for a total of 60 possible radial wire connections. Packages that include the UNUN also include the UNUN mounting bracket. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. *US Patents D654,063 and D654,064 DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas are high-performance verticals and antenna packages that allow you to access all HF bands with only one antenna solution. Order one of these premium-quality all-band HF verticals from DX Engineering and roam HF… freely!
( 9 )
$601.98
—
$744.64
DX Engineering HF Portable TW Antennas and Accessories
Preserving and building upon the legacy of this premier portable HF antenna line, DX Engineering is now the manufacturer and seller of TW Antennas! DX Engineering's acquisition of the products and designs of these unique HF portable and stealthy antennas brings easy access and simplified ordering to this line formerly known as Transworld. DX Engineering HF Portable TW Antennas and Accessories feature complete portable antenna packages and all of the individual components to build a custom stealthy system. Will you use these compact HF antennas as portables, fixed antennas, or both? Choose your own path to stealthy operations and to join in the fun of portable HF! Naturally stealthy, these compact HF vertical-dipole TW antennas feature a black finish that is excellent on fixed antennas in HOAs or where "CC & R" antenna restrictions preclude the installation of towers and easily visible HF antennas. Simply unfold the DXE-TW-BAS-BLK Top and Bottom Sections, add your Band Box Center Post section, and place the antenna on the optional 41 in. long permanent mounting post, DXE-TW-PMP, and operate! Note: Although a permanently-installed mounting pier (DXE-TW-PMP) is available, DX Engineering TW Antenna band boxes are not waterproof. Do not leave your TW Antenna exposed to the elements. For portable use, the lightweight foldable Quadrastand, DXE-TW-AQ, lets you set up your DX Engineering HF Portable TW Antenna wherever you happen to be. Quadrastand's gray fiberglass legs will give decades of rugged, dependable service. And since they're fiberglass, there's no chance of corrosion from contact with earth or sand. Think about equipping for your special operating event plans like Scouts Jamboree On-The-Air (JOTA), Field Day or even SOTA (Summits On-The-Air) for backpacking and general camping with HF! A great Carry Case, DXE-TW-DXBAG, is available to make traveling with these antennas in your car or RV a snap. DX Engineering HF Portable TW Antennas and Accessories are available as mono-band or multi-band systems. Covering all five bands from 20 through 10 meters, DXE-TW-2010 Multi-Band Remote Switching Center Sections include a control console and cable and can be band-switched remotely in the shack and automatically by some transceivers. DXE-TW-2010L Multi-Band antennas can be band-switched manually. Plus, it's easy to change to the 80, 40 and 30 meter operations with DXE-TW-8080, DXE-TW-4040 or the DXE-TW-3030. Swap out each Band Box Center Post to change to operations on these different bands in a very simple manner. Typical installation for TW Antennas is a compact 8.25 ft. tall and only 5 ft. wide. Make your choice; portable, fixed or both, then equip yourself with the best compact vertical-dipole antennas available. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering HF Portable TW Antennas and Accessories are here to help you enjoy working stealthy HF at home or… anywhere! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
( 19 )
$595.99
DX Engineering HF Antenna Mounting Tilt and Pivot Bases
Whether you are building a low-band or multi-band HF vertical starting with a 2 in., 3 in., or 4 in. base tubing, DX Engineering HF Antenna Mounting Tilt and Pivot Bases let you raise your vertical without asking for help! Featuring high strength Extren® insulated channels and all stainless steel construction, these tilt bases and pivoting fixtures are ready for your "Big Signal" HF antenna. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 7 )
$729.99
DX Engineering Dual Input Remote Antenna Switches
DX Engineering Dual Input Remote Antenna Switches are two-radio 8-antenna switches (2x8) designed to switch coaxial lines in medium to high power RF antenna systems. With excellent performance on HF and 6 meters, they are typically used in single operator two-radio (SO2R) or multi-two contesting stations. They offer high levels of port-to-port isolation and reliability, the same as the famous DX Engineering RR8 series single input 8-port remote antenna switches. Manual dual-control operation of the DXE-RR2X8B is possible with two separate 1-of-8 control consoles that send +13.8VDC to the selected port, such as the DXE-EC-8. In this instance, the main transceiver has precedence over the secondary when attempting to use the same antenna port, so manual switching care must be exercised. An alternative first come, first served switching approach is available with the optional DXE-MX2X8 Interface Unit. It accepts BCD signals from two DXE-CC-8A Deluxe Control Consoles, and it locks out the selected port from the other radio, rather than main port precedence. DX Engineering RR2X8B Dual Input Switches may be interfaced with a customer-supplied logical switching unit. A third-party antenna controller with dual 1-of-8 switching may be used directly with the DXE-RR2X8B Switch or with BCD to the DXE-MX2X8 Interface Unit. If the DXE-MM2X8 Interface Unit is not used, the third party unit must provide protection against hot switching and prevent the main or secondary radio ports from attempting to select the same antenna port at any time. DX Engineering Dual Input Remote Antenna Switches feature a custom-made stainless steel chassis and a special RF shielded high impact thermoplastic cover. They have a custom conductive gasket to complete the seal between the cover and stainless steel housing base. Disassembly is not required for control wiring access. DX Engineering RR2X8B switches use removable screw terminals for the control cable plugs. These removable plugs greatly simplify installation by eliminating the need for soldering or opening the enclosure. The internal, covered relays are moisture-resistant, providing many years of exceptional performance. The circuitry of the DXE-RR2X8B switches allows the simultaneous selection of multiple antenna port with the required control signals. They can be used in complex antenna systems including stacked and phased arrays. Also, conventional one-of-eight antenna switching for two separate stations is possible using separate 1-of-8 switching arrangements. For example, the main radio Input "M" may select and be connected to any of the 8 ports while the secondary Radio Input "S" can simultaneously select any of the ports that the main isn't using. The main controller always has precedence over any selection made by the secondary controller, unless the DXE-MX2X8 is employed. Features of DX Engineering Dual Input Remote Antenna Switches include: * Rugged, attractive, fully shielded weatherproof housing * DX Engineering stainless steel V-clamp included for easy mounting to tower legs or masts from 1-2 in. diameter * Multi-conductor external cable plugs for easy removal, connection and maintenance * Excellent port-to-port Isolation; greater than 70 dB at 30 MHz, worst case; greater than 60 dB up to 60 MHz * High RF tolerant UHF connectors * Enclosed 16 ampere RF relays * Safe 12V DC relay operation * 16 MOVs for surge protection on control lines * 16 RF bypass capacitors Note: Whenever the DX Engineering "Documentation" is available, please look at the associated files for additional product information. Make your SO2R or other multi-radio multi-antenna operations easy with a DX Engineering Dual Input Remote Antenna Switch.
( 3 )
$669.99
DX Engineering Digital Rotator Controllers
DX Engineering Digital Rotator Controllers are completely new, extremely advanced and adaptable controllers for your directional antenna rotation systems. Offering the ultimate in operational capabilities, the RT-21DXE Digital Rotor Controllers are the best controllers available for your new rotor unit or as a replacement in existing systems. The RT-21DXE comes preset for 24 VDC for operation with the DXE-RT4500HD Heavy Duty Rotator, but they are easily adaptable for use with other directional antenna rotation systems because they are field programmable with convenient, internal, solderless jumpers. Replace your old-fashioned rotator controller with a modern, state-of-the-art digital controller. Order your DXE-RT-21DXE Digital Rotor Controller from DX Engineering today! DXE-RT-21DXE Additional Features and Specifications: You can add these great features to your existing rotator unit, without even climbing the tower! * Preset for 24 VDC for operation with the DXE-RT4500HD Heavy Duty Rotator * High-visibility LCD display with adjustable backlight brightness * Fully versatile controls for point-and-shoot or manual push-button operation plus presets * Automated rotator computer control through RS-232 or USB * PWM (pulse width modulated) variable-speed control * Start and stop ramping to reduce tower and antenna stresses * Precision heading accuracy up to 1/10 degree * Fully supports side-mounted antennas, soft limits prevent running into the tower * Allows over-travel up to 720 degrees total * Offset control allows the center of rotation at any heading, allows N & S center on the mast, and compensates for slipped mast * Fully user-programmable, reversal and brake delay, speed minimum and maximum, limits, ramps, and much more * Master/slave for stacked arrays, turn together or separately * Counter-rotation, install rotor above rotating tower * Easy front panel setup and setup utility software Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
Not Yet Reviewed
$714.99
DX Engineering RR8B Remote Antenna Switch and Control Console Packages
DX Engineering RR8B Remote Antenna Switch and Control Console Packages bring a new level of convenience to your antenna setup. These packages combine DX Engineering's 5 or 10 kW key-down switch, plus a CC-8A or EC-8 Control Console. RR8B series Remote Antenna Switches feature: * 0-54 MHz operation with industry leading port-to-port isolation * 5 or 10 kW versions * Fully RF shielded with high strength, UV-resistant cover, stainless steel mounting bracket, and hardware * Lightning protection is standard * Solderless, removable plug for easy installation of control line with no disassembly * Can be wired without disassembly * Can select individual or multiple ports for stacking and phased array applications * Safe 12V DC relay operation * Unused antenna ports are open by design; may be internally jumpered to be grounded when not selected CC-8A Consoles feature: * 1-of-8 control format * 8 front panel LEDs to indicate switch position (with adjustable brightness) * Rear panel external plug * Operates on your 12V DC source, ideal for battery or emergency ops * Ergonomic selector knob * Powder-coated metal housing EC-8 controller features include: * 1-of-8 control format * Green power LED * Operates on your 12V DC source, ideal for battery backup or EMCOMM * Ergonomic selector knob * Powder-coated metal housing Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When a complete remote antenna switching system is needed and high reliability is a must, DX Engineering RR8B Remote Antenna Switch and Control Console Packages are your best solution! * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
( 8 )
$739.98
DX Engineering PRO-STACK Broadband Antenna Phasing Switches
DX Engineering PRO-STACK Broadband Antenna Phasing Switches are newly designed to combine two identical Yagi or log periodic beams, or three quarter-wave vertical antennas, into a phased array for enhanced operation. There is no need for coaxial delay lines with the DX Engineering PRO-STACK switches. Just connect your antennas to the phasing switch controller with equal-length 50 ohm lines. PRO-STACK switch units are available with high-quality PTFE-silver plated SO-239 (UHF female) connectors. These relay units are 1-of-3 source voltage controlled at 12-15VDC over a four conductor cable. A matching Control Console is available separately or is included in the PRO-STACK System. These phasing switches can be used for any applications that require the following four basic antenna feed selections: both antenna ports in-phase, both antenna ports out-of-phase, antenna port 1 only, and antenna port 2 only. The default is both output ports in-phase. Impedance matching automatically changes when any antenna port is disconnected. Generally, stacked Yagi antennas are separated vertically greater than 1/2-wavelength free space. Since the DX Engineering PRO-STACK Broadband Antenna Phasing Systems are broadband, they may be easily adapted to larger arrays. For example, four stacked Yagis may be combined by creating two sets of two, and then using a third DX Engineering control console to combine the first two sets. PRO-STACK switches can also be used to feed three quarter wave resonant vertical antennas for a high-gain 4-pattern array. In this arrangement, the center #2 passive element is directly grounded to a good ground radial system at all times, while the end elements #1 and #3 are then fed in various phase relationships by the PRO-STACK. Details are in the complete PRO-STACK PS-2B Instruction Manual linked here in Documentation. Features of the DX Engineering PRO-STACK Broadband Antenna Phasing Switches include these great features: * Power handling up to 5 kW * Broadband coverage on 160-10 meters * High-impact RF shielded weatherproof housing * High-RF tolerant, silver-PTFE SO-239 (UHF female) connectors * Proven DX Engineering RF relays for high performance * Safe 12 VDC relay operation, even on battery or solar power * MOV surge protection on control lines * External, removable control line connector * RoHS-compliant assembly
( 1 )
$699.99
—
$740.00
DX Engineering Reversible Beverage Antenna System Combos
DX Engineering Reversible Beverage Antenna System Combos allow two Beverage antennas to be switched to receive in opposite directions while sharing the same physical space. These exciting new reversible Beverage combos include DX Engineering's superb receive preamp! Dramatically improved weak signal results can be achieved on MW, BCB, 160, 80 and 40 meter bands and shortwave bands with receive-only Beverage wire antennas that are typically 350 to 800 feet long, depending upon the lowest band of interest. DX Engineering Reversible Beverage System Combos are immune to the strong signal overload and core saturation common in multi-transmitter contesting environments. Reversible Beverages have two antenna F connectors; one "Away" port for the default end-fire receiving pattern off the end of the wire, and one "Toward" port for the opposite direction. Applying a negative 10 to 18 V DC to the feedline switches the system between the two antenna ports for reception in opposite directions. You can build a 4-direction receive antenna system with two reversible Beverage systems and one DX Engineering RLS-2 Two-Port Receiving Switch that also requires only one feedline! The optional DX Engineering Feedline Voltage Coupler, model DXE-FVC-1 is highly recommended to provide all of the required feedline voltage injection. Plus, the optional DXE-EC-4 BCD Control Console completes the system for four-direction switching right in the shack. These RBS systems will work with any 300-600 ohm 2-wire line. For best low-loss low-noise results, use DX Engineering flooded or quad-shielded 75-ohm coax; with our F-type compression connectors to ensure a weatherproof installation. DX Engineering RPA-1 Receive Preamplifiers use RCA-type phono jacks and CATV Type-F female connectors for the input and output connections to prevent accidental connection to transmitting devices. RPA-1 Receive Preamplifiers feature a built-in relay that automatically bypasses the preamplifier circuit when DC power is removed. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 V DC input. Details for DX Engineering Reversible Beverage Antenna System Combos: Receive preamp: * Gain: 16 dB, +/- 1.5 dB, from 300 kHz through 35 MHz * Dynamic range (IM3) at 500 Hz BW: 110 dB or greater * Output Third Order Intercept: +43 dBm * Noise figure: 3.5 dB * Compression: 1 dB at +26 dBm (nominally 0.4 W output) * Power requirement: 12-18 V DC at 140 mA maximum * Power Input: 2.1 mm DC coaxial power connector Reversible Beverage transformer features: * Broad operating range, 0.2 to 30 MHz * Fully isolated grounds prevent common-made noise and unwanted signals * 75 ohm design enables the use of high quality, low cost cable and connectors * RF shielded housing used for isolation and improved life * Directional Switching Voltage: nominal 12 V AC or negative 12 V DC, feedline injected * Directional Switching Current: less than 80 mA * Antenna impedance: 300-600 ohm (450 ohm recommended) * Feedline impedance: 50-75 ohm (75 ohm recommended) * RBSA-1FP Feed Point unit dimensions: 5.5 in. width x 3.5 in. depth x 1.5 in. height * RBS-1RT Reflection Transformer unit dimensions: 2.125 in. width x 2.125 in. depth x 1.125 in. height Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Reversible Beverage Antenna System Combos offer package convenience and superior receiving results on today's crowded medium and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the exceptional performance of DX Engineering products. Order one of these DX Engineering Reversible Beverage Antenna System Combos to make the best of your MW/HF reception!
Not Yet Reviewed
$605.97
DX Engineering TW Antenna 40 Meter Solo Explorer Packages
Preserving and building upon the legacy of this premier portable HF antenna line, DX Engineering is now the manufacturer of TW Antennas!* DX Engineering's acquisition of the products and designs of these unique HF portable and stealthy antennas brings easy access and simplified ordering to this antenna line formerly known as Transworld. DX Engineering TW Antenna 40 Meter Solo Explorer Packages include everything you need to go portable! The package is comprised of the basic antenna structure, the band box and an antenna stand. You supply the coax and your own powered transceiver. It's a great antenna for portable Low-Band QRP! Naturally stealthy, these compact HF vertical-dipole TW antennas feature a black powdercoat finish that is excellent for antenna use in HOAs. Use them where "CC & R" antenna restrictions preclude the installation of towers or easily-visible HF antennas. Simply unfold the DXE-TW-BAS-BLK Top and Bottom Sections, add your Band Box Center Post section, and place the antenna on the antenna stand and operate! No radials are needed with these 40-meter vertical dipoles! Ideal for portable use, the lightweight Quadrastand, DXE-TW-AQ, lets you set up your DX Engineering HF Portable TW Antenna wherever you happen to be. Think about special operating events like Scouts Jamboree On-The-Air (JOTA), Field Day or even SOTA (Summits On-The-Air). For general camping and travel, a convenient and durable carrying case, DXE-TW-DXBAG, is OPTIONALLY available to make transporting these antennas in your car or RV a snap! Typical installation for TW Antennas is a compact 8.25 ft. tall and only 5 ft. wide. Make your choice; portable, fixed or both, then equip yourself with the best compact vertical-dipole antenna available. Note: Although a permanently-installed mount is available, DX Engineering TW Antenna band boxes are not waterproof. Do not leave your TW Antenna exposed to the elements. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering TW Antenna 40 Meter Solo Explorer Packages are here to help you enjoy working stealthy HF at home or… anywhere! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
( 2 )
$748.96
DX Engineering 4BTV Four-Band High Performance HF Vertical Antenna and Original Tilt Base Systems
DX Engineering 4BTV Four-Band High Performance HF Vertical Antenna and Original Tilt Base Systems are convenient and economical antenna installation packages that combine the time-tested Hustler antenna with our radial plate and our innovative tilt system. DX Engineering Hustler 4BTV Packages provide 40, 20, 15, and 10 meter band operation with: --Dramatically improved transmit and receive signals --Best possible signal pattern and performance boost with organized radial wire attachment system --Simplified and long-lasting RF connections with proper connectors and cable --Safe and easy tuning using our patented original Tilt Base - one person can walk the antenna up or down --Professional grade stainless steel clamps and mounting hardware Included with these antenna packages is our exclusive High Performance Hustler BTV Assembly and Installation Guide that will answer all your questions! You can read more about the best way to install your vertical antenna system, the reasons for installing a radial system, and find out how to "Install Radial Wires Without Digging". Click the "Documentation" link to The Guide. Make contacts beyond expectations! Operate with a versatile HF multi-band vertical antenna that performs to its full potential.
( 1 )
$712.69
DX Engineering DVA Dual Vertical Array Systems
DX Engineering DVA Dual Vertical Array Systems are advanced phasing systems that have set a new standard for array performance with two ground-mounted verticals. Dual Vertical Array Systems include a compact DVA Phasing Relay Unit made specifically for an individual HF band and an EC-DVA Directional Control Console. DX Engineering Dual Vertical Arrays produce two opposite enhanced End-Fire Cardioid patterns and one Broadside-Omni pattern. Heavy-duty components handle over 2 kW continuous RF power for enhanced performance at low SWR over a wide bandwidth. The Dual Vertical Array end-fire directional patterns achieve a real front-to-back over 20 dB with typical array forward gain up to 3 dB over a single vertical. The greatest advantage of a Dual Vertical Array is that a tower and rotator are not required, as with a Yagi antenna. Especially for 160, 80, and 40, and even on the other HF bands, a Dual Vertical Array is mechanically simpler and safer. Here is a financially practical directional antenna that is much easier to install! These are great directional antenna systems for temporary and Field Day operation, as well as for permanent builds, because they ARE so much easier to install than a beam! If you are dissatisfied with your present system, are ready for an upgrade, or just need to get out of the tower game, the DX Engineering DVA is your answer! Refurbish an existing antenna system, equip your temporary array, or build a new phased array with a DVA. It's all on the ground, safe and simple: DX Engineering Dual Vertical Arrays offer a better way to enjoy a high-performance mono-band directional antenna. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 4 )
$575.98
—
$685.98
DX Engineering Receive Four Square Array Electronics Package
DX Engineering Receive Four Square Array Electronics Package, DXE-RFS-SYS-2P, is for the array builder who wants to use their own passive receive verticals for a mono-band receive array. See the DXE-R4S-SYS-V3 for the Complete Receive Four Square V3 Array System with Receive Short Element Active Verticals. DX Engineering Receive Four Square Arrays dramatically improve reception of weak distant signals with excellent rejection of extraneous signals and noise. This four-direction switchable array uses time delay phasing of four physically short receiving vertical elements. The resulting directional receiving pattern is superior to four short Beverage antennas and typical two or three element arrays. The Receive Four Square is less susceptible to high angle signals than EWE, Flag, Pennant, K9AY and SAL antennas. This type of receive array, using physically short vertical elements, limits signal and noise for dramatically superior weak signal reception, as compared to full size transmitting antennas and arrays. With proper spacing of four unobtrusive, physically short vertical elements, the Receive Four Square Array System provides high performance directional receive for HF Amateur, SWL or AM DXing. Click or tap the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. DX Engineering Receive Four Square Arrays offer directional performance comparable to four long Beverage wire antennas, using far less land area. This Controller and Switch Console package is designed to be used with four identical, user-supplied, active or passive symmetrically-spaced ground-mounted vertical elements to provide switching for a 4-direction receiving antenna system. Passive elements will generally provide an optimized monoband receiving system. Conversely, with four DX Engineering Receive Short Element Active Vertical antennas, DXE-RSEAV-1, the properly sized array can achieve excellent directional receiving performance over three HF bands. Build an exceptionally effective, electronically rotatable, stationary receive antenna that lets you hear the DX that cannot be heard on a transmit antenna. Dig the weak signals out of the noise with an antenna that can help make your station one of the best; install the DX Engineering Receive Four Square Array System. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$553.98
DX Engineering DVA Phasing Relay Units
DX Engineering DVA Phasing Relay Units are the band specific parts of the Dual Vertical Array Systems. These are larger, new Phasing Relay Units for any HF band, 160 through 10 meters. New heavy-duty components handle 2 kW continuous RF power for array performance at low SWR over a wide bandwidth. These mono-band weatherproof DVA Phasing Relay Units include a clamp for mounting directly between two ground-mounted, full-size, quarter-wave resonant verticals. Their companion DXE-EC-DVA Directional Control Console is a 3-direction array pattern selector that operates on 13.8 Vdc and features a 3-position rotary switch, directional LED indicators and scratch pads.. Dual Vertical Array end-fire directional patterns achieve a real front-to-back over 20 dB with typical array forward gain up to 3 dB over a single vertical. Specifications for the DX Engineering Dual Vertical Array: * Forward Gain (approx., compared to single vertical): 3 dB End-Fire; 1 dB Broadside-Omni * Front-to-back: Over 20 dB nominal, end-fire patterns * Power Handling: 2 kW continuous * RF Connectors: Three SO-239 (UHF female); Transmitter, Antenna 1, Antenna 2 * Control Cable: 3 conductors, min. 20 AWG * Control Cable Set-Screw Connectors: Relay Unit--external; Control Console--internal DX Engineering Dual Vertical Array mono-band phasing systems are available for each HF band, with 160, 80 and 40 meters in stock, and 60 30, 20, 17, 15, 12 and 10 meter systems available by special order. Your phased array pattern results may vary, due to band conditions, the surroundings at antenna and the radial system installation. Additional information is in the Dual Vertical Array instruction manuals, linked at each system description web page.
Not Yet Reviewed
$509.99
—
$609.99
DX Engineering Rotator Super Duty Mast Clamps
DX Engineering Rotator Super Duty Mast Clamps are designed to be used where maximum torque handling is required on aluminum, steel, Chromoly steel or stainless steel mast tubing, significantly improving the connection between the rotator and the directional antenna rotating mast over other types of mast clamps. With the choice of two Super Duty Saddle Clamps or the "HD" model with three Super Duty Saddle Clamps, these remarkable rotator mast clamps are available in three sizes; for a 2 inch OD mast (DXE-SDMC-2 and -2HD), a 2.5 inch OD mast (DXE-SDMC-2-5 and -2-5HD) and a 3 inch OD mast (DXE-SDMC-3 and -3HD), intended for use only on tubing, not for fractional sized pipe. Rotator Super Duty Mast Clamps are designed and manufactured to mate with the DX Engineering DXE-RT4500HD Heavy Duty Rotator. Each powder coated steel Super Duty Mast Clamp vertical plate has holes for the applicable Super Duty Clamps and the base plates have an integral weep channel to ensure moisture is not trapped in the mast. These mast clamps are complete, supplied with two (standard) or three (HD) Super Duty Saddle Clamps, stainless steel backing plates, rugged 8-18 stainless steel 3/8-16 hex mounting and clamp bolt sets, with all fastener hardware included. Unlike stamped or machined-type clamps, Super Duty Saddle Clamps are cast from a rugged aluminum alloy that grips tubing with a special textured surface for an incredibly secure fit that resists torque, wind and weather. All three sizes, DXE-SDMC-2/-2HD, DXE-SDMC-2.5/- 2.5HD and DXE-SDMC-3/-3HD can be used on Rohn 45 and larger towers. Only the 2 inch mast versions DXE-SDMC-2 and -2HD will fit inside Rohn 25G towers. NOTE: Whenever the planned installation of mast mounted rotatable antennas will have a total wind load or wind exposure rating of 18 square feet or more, the use of a 2.5 or 3.0 inch OD mast with a DX Engineering Rotator Super Duty Mast Clamp is highly recommended.
Not Yet Reviewed
$503.47
DX Engineering Antenna Boom Tubing Kits
Two different DX Engineering Antenna Boom Tubing Kits can be used to replace a 3-in. boom of either 24 ft. or 48 ft. in length. Also, both extra heavy -duty aluminum tubing boom kits are the perfect choice to provide the backbone for the Yagi project of your dreams! The DXE-ABT3-24R supplies two 24 ft. pieces of heavy-wall aluminum tubing; one 3-in. OD tube and one 2.715 in. OD piece that telescopes inside the larger tube to provide superior reinforcement. The DXE-ABT3-48 provides three pieces of heavy-wall tubing in total; two 24 ft. pieces of 3-in. tubing and a 24 ft. long 2.715 in. diameter splice insert that fits 12 ft. inside each larger tube for reinforcement, to create a truly exceptional 48 ft. boom. These heavy-duty antenna booms are suitable for Yagis and log periodic arrays from 40 through 10 meters. These booms are not pre-drilled for assembly and will require drilling and fitting to suit your needs. Before assembly, any dirt or foreign material will need to be removed from the boom pieces and splice piece. The inside and outside of all tubes must be thoroughly cleaned. This will allow smooth joining of the aluminum without jamming. Application of SS-30 Jet Lube is also a must to allow long lengths of the precision aluminum splice tube to telescope inside the boom tubes. Joining bolts are included but any other antenna assembly hardware is user supplied. If you have a large antenna project in mind that requires a strong boom assembly, these DX Engineering Antenna Boom Tubing Kits are the choice you're looking for!
( 1 )
$601.99
DX Engineering Antenna Packaging Component
DX Engineering Antenna Packaging Component - an individual container with some parts of a product for which there are two or more different packages, each with unique part numbers.
Not Yet Reviewed
$518.99
DX Engineering TW Antenna 30 Meter Solo Explorer Packages
Preserving and building upon the legacy of this premier portable HF antenna line, DX Engineering is now the manufacturer of TW Antennas!* DX Engineering's acquisition of the products and designs of these unique HF portable and stealthy antennas brings easy access and simplified ordering to this antenna line formerly known as Transworld. DX Engineering TW Antenna 30 Meter Solo Explorer Packages include everything you need to go portable! The package is comprised of the basic antenna structure, the band box and an antenna stand. You supply the coax and your own powered transceiver. It's a great antenna for portable Low-Band QRP! Naturally stealthy, these compact HF vertical-dipole TW antennas feature a black powdercoat finish that is excellent for antenna use in HOAs. Use them where "CC & R" antenna restrictions preclude the installation of towers or easily-visible HF antennas. Simply unfold the DXE-TW-BAS-BLK Top and Bottom Sections, add your Band Box Center Post section, and place the antenna on the antenna stand and operate! No radials are needed with these 30-meter vertical dipoles! Ideal for portable use, the lightweight Quadrastand, DXE-TW-AQ, lets you set up your DX Engineering HF Portable TW Antenna wherever you happen to be. Think about special operating events like Scouts Jamboree On-The-Air (JOTA), Field Day or even SOTA (Summits On-The-Air). With robust 30 meter digital modes, DX contacts will be oh-so easy! For general camping and travel, a convenient and durable carrying case, DXE-TW-DXBAG, is OPTIONALLY available to make transporting these antennas in your car or RV a snap! Typical installation for TW Antennas is a compact 8.25 ft. tall and only 5 ft. wide. Make your choice; portable, fixed or both, then equip yourself with the best compact vertical-dipole antenna available. Note: Although a permanently-installed mount is available, DX Engineering TW Antenna band boxes are not waterproof. Do not leave your TW Antenna exposed to the elements. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering TW Antenna 30 Meter Solo Explorer Packages are here to help you enjoy working stealthy HF at home or… anywhere! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
Not Yet Reviewed
$748.96
DX Engineering Tinned Copper Radial Wire Kits
DX Engineering Tinned Copper Radial Wire Kits include plentiful quantities of biodegradable staples and tinned crimp ring terminals that are easily soldered. Along with spools of the same wire as used by the most successful contest stations and DX enthusiasts for their ground-mounted vertical antennas, these kits will help your antenna system achieve optimal performance. The 16 AWG tinned solid copper wire in these kits provide an extremely cost effective solution for the high-count, full-size ground radial wire systems that are required for top-performing HF vertical antenna installations. Ground wire radials do not need to be any specific length because the earth detunes them. Fill your ground-mounted vertical space with radials that run out from the antenna feedpoint in all possible directions, as far as they can go, up to about one-quarter wavelength on the lowest frequency. Even radials that are all about one-eighth wavelength long on the lowest frequency band are just fine for multi-band verticals over reasonably conductive soils. Use longer radials on lossy soils with sand and rocks. In most cases, a greater number of short ground radials will provide greater efficiency and stronger signals than is achieved with a few long radials. DX Engineering Tinned Copper Radial Wire Kits are available in four sizes: Shorter spool kits, 500 ft. and 1,000 ft., are perfect for the single HF ground-mounted vertical. Longer spool kits, 2,500 ft. and 5,000 ft., are intended for 2-element Dual Vertical Arrays, 3-element ProStack Arrays, and 4-element Four Square Array Systems. Each kit has the appropriate number of biodegradable staples and tinned crimp ring terminals. Why is this wire the absolute best choice for any ground-mounted vertical antenna? Because, DX Engineering Tinned Copper Radial Wire will last much longer in a variety of soil conditions as compared to bare copper, copper coated steel or aluminum wires. Radials deployed with those other wire types actually corrode and degrade rather quickly. Unfortunately, they do so slowly enough that the operator does not easily perceive that degradation in terms of antenna system performance. With Tinned Copper wire, full radial system integrity is maintained for a greater number of years. Depending upon soil type, installations with DXE-TCRW16 will maintain vertical antenna performance for many, many years… and even decades. NOTE: To prevent accelerated corrosion and the possibility of noise, DO NOT use metal anchor pins (lawn staples) on Tinned Copper Radial Wire. These kits contain only the DXE-STPL-100BD Biodegradable Anchor Pins to hold down bare wire radials. Biodegradable staples allow easy installation of radial wires and will disperse in a couple years, after they are no longer needed, making them site friendly. Biodegradable staples work best in soft ground where they may be pushed or lightly tapped into the ground. Since they are a lacto-resin material they are subject to breaking in rocky or hard soil and are not intended to be hammered. DX Engineering Tinned Copper Radial Wire kits are the right choice for long lasting top-performance radial systems for your ground-mounted vertical antenna system.
( 2 )
$683.87
DX Engineering MBVE-5AE Series SAF-T-TILT™ Auto-Tune HF Multi-Band Vertical Antennas
DX Engineering MBVE-5AE Series SAF-T-TILT™ Auto-Tune HF Multi-Band Vertical Antennas are high performance, 80 through 10 meter vertical antenna systems. They are designed from the ground up to offer ease of use, reliability and performance! New design and materials technology are used throughout. The patented* and massive SAF-T-TILT™ 3/8 in. thick rugged aluminum base allows easy, safe tilt action without the unsafe removal of mounting hardware -- as with some competitors' antennas! Plus, these self-supporting HF vertical antennas, at just over 40 ft. in height, feature DX Engineering's exclusive new mounting brackets that secure the automatic antenna tuner above the tilt base for easy installation and access, away from potential damage by water and animals. Using our MBVE-5AE Series SAF-T-TILT™ Auto-Tune ground-mounted vertical, you'll work DX as you never could with a low, horizontal dipole antenna! If you have a location that is limited by HOA or CC&R restrictions, where a tower isn't possible or if there are no trees for wire antenna supports, these slender, unobtrusive HF Multi-Band Vertical Antennas can opens up a new world of HF operations. Click on the DOCUMENTATION tab in any of the antennas listed below and then click on the CHARTS and GUIDES link to see all of the MBVE-5AE Auto-Tune Vertical Antenna offerings. Some of these antenna packages include the tuner and some include tuner mounting brackets and hardware only, for those who already own that tuner. All antenna packages include the antenna tuner mount, antenna element tubing with insulator, exclusive, patented* SAF-T-TILT™ Base Antenna Mount, stainless steel hardware and clamps. If you already have a DX Engineering MBVE-5 or MBVE-5A antenna, then use our MBVE-5UG series Upgrade Kits to add an extension tube, elevated tuner mount and auto-tuner. Search MBVE-5UG above. This all-new series of MBVE-5AE SAF-T-TILT™ Auto-Tune HF Multi-Band Vertical Antennas feature: * Massive, patented* SAF-T-TILT™ base allows safe raising and lowering of antenna without removal of fastening hardware * High strength Delrin® thermoplastic insulator that won't crack, splinter, peel or fail from exposure * Rugged structural grade type 6063-T832 drawn aluminum tubing radiator - the best alloy for high-strength, long-lasting antenna applications plus an extended tubing, brackets and hardware for tuner mounting * The fast taper antenna element provides the lowest wind resistance- very durable and attractive * Free-standing to 92 mph wind speeds Like any HF vertical, MBVE-5AE verticals require a good ground radial system. We highly recommend installing 32 radials, 65 ft. long are recommended. Fewer or shorter radials will work, but with some diminished results. A great ground-mounted vertical has the available space covered with 20 or more evenly spaced radials, each of any length from 15 to 65 ft. Do the work and you'll work the world! ™ For proper installation, additional materials are needed, but not supplied. You will need: * Mounting pipe--steel pipe that has 2.0 in. O.D. with 0.25 in. wall thickness, 4 ft. long -- standard 1-1/2 in. galvanized water pipe (with its 1.9 in. OD) is fine * Quick-Set or other concrete for mounting pipe installation * Radial wire and wire lugs--must use 14-gauge, stranded copper wire with PVC insulation. * Jet Lube SS-30 Anti-oxidant Anti-Seize –model JTL-12555 is highly recommended to ensure good connection between aluminum hardware and in-between aluminum tubing sections and for use on the threads of all the stainless steel hardware to prevent galling Note: For additional information, please look at the files under the "Documentation" tab. DX Engineering MBVE-5AE Series SAF-T-TILT™ Auto-Tune HF Multi-Band Vertical Antennas are high-performance verticals and antenna packages that allow you to access almost all HF bands with only one antenna solution. *US Patents D654,063 and D654,064
( 5 )
$680.97
—
$712.97