Availability
42 Results Found For "noise"
DX Engineering NCC-2 Receive Antenna Phasing Systems
Imagine adjusting the controls to knock out strong interfering stations or noise—and then being able to copy and log that weak DX station. By successfully combining the right antennas with the advanced phasing capabilities of the NCC-2, this is the operating thrill that every radio enthusiast can enjoy, again and again! DX Engineering NCC-2 Receive Antenna Phasing Systems are variable phasing controllers that combine the 300 kHz- 30MHz received signals from one transmit antenna and one receive antenna, or from two dedicated receive antennas. Combining signals from two stationary antennas physically spaced 1/10 to 1/2 wavelength apart creates an array pattern with signal peaks and dips called nulls. Adjusting the NCC-2 Phase and Balance controls have the effect of electronically rotating or steering that pattern. Steering the null direction to significantly weaken a local or distant interfering signal or noise is known as "Noise Cancelling." This "Noise Cancelling Controller" (NCC-2) can dramatically enhance the reception of weak signals from non-null directions. This "reverse-beam" capability on radio frequencies AM Broadcast through HF can provide amazing benefits for many types of AM DX and SWL receiving and ham radio operating. Work new DX, hear the weak station in casual regional conversations, snag the rare multiplier in contests and hear beyond the noise and interference in dire circumstances. DX Engineering NCC-2 Phasing Systems now feature the built-in RTR Receive-Transmit Interface relay system that expands the exciting benefits of antenna phasing for interference reduction in two ways: * First, the NCC-2 can combine signals from the HF transmit antenna and a separate receive antenna to effectively notch-out strong stations or noise. Almost any Amateur can now enjoy the benefits of antenna phasing and noise-nulling, even those with space limitations for separating the receiving and transmitting antennas. * Second, the user of any standard HF transceiver that lacks a separate receive antenna input can have enhanced reception of noise and signal nulling with the DXE-NCC-2 and two antennas. Rear panel SO-239, F and BNC connectors make the NCC-2 extremely versatile and easy to connect to almost any receiver or HF transceiver up to 200 watts. Redesigned with plug-in modular circuit board sockets, the NCC-2 includes one switched and powered internal slot and two passive internal slots per channel to accommodate these new options: * DXE-RPA-2-PM Receive Preamplifier Plug-In Modules (powered): one per channel for low-signal passive antennas with poor ground conditions * DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module (passive): Front-end protection for the NCC-2 and the receiver * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-In Module (passive): to match 75 ohm RX ANT feedlines to NCC-2 50 ohm internal impedance * NCC-2 Receive Filter Sets (passive, non-switchable): High Pass, Band Pass and Low Pass Filters for 160, 80, 40 meters typically in stock, with other band filters available individually by special order. DX Engineering NCC-2 Receive Antenna Phasing Systems offer these new additional benefits: * Multi-Color Status Indicating LEDs for Power, RTR Mode and Preamp Power CH A and CH B * New Radio Key Line Input with RX Enable Output-RTR Failsafe to prevent RF damage to NCC-2 and RX equipment * New ACC Key Line Output RCA female 'ground on transmit' pass-through for Amplifier or Accessory * New screw-on 2.1mm DC connector to prevent accidental power cable pull-out * Operates on +13.8VDC @ 2A input to power the NCC-2 and internally jumper set Bias Tee on each RX ANT ports for coax fed Active Verticals and other accessories. Offering new and experienced radio enthusiasts the next level of reception enhancements, DX Engineering model NCC-2 Receive Antenna Phasing Systems in use around the world!
( 19 )
$955.99
DX Engineering AVA-3 Active Matching Units
DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.
( 6 )
$139.99
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$17.49
—
$464.45
DX Engineering Portable Receive Preamplifier-Attenuator
DX Engineering Portable Receive Preamplifier-Attenuator DXE-NL-PRE-ATT-1 – A very handy device to use with your receiver; handheld, portable or base. This attractive, light-weight unit comes completely assembled and tested, and provides a nominal 30 dB gain across the frequency range from 100 kHz through 30 MHz. Powered by an internal 9 volt battery (not included), it features BNC connectors for RF Input and Output, easy to use slide switches and a 'power on' LED when the preamp is on. Attenuation is selected with switches for -10 dB or -20 dB and -30 dB with both. Plus, an AM Broadcast Band Rejection Filter can be switched in or out, as needed. This unit measures 3.25 x 7.00 x 1.00 in. (WHD) and weighs approx. 8.5 oz. with the user supplied 9V battery installed. This preamplifier has a Noise Figure (NF) of 4.5 dB. This Portable Preamplifier-Attenuator is a perfect companion device for use with the DXE-NOISELOOP WD8DSB Portable Receive Flag Antenna Kit, for RFI noise finding and for MW through SW receiving. NOTE: The DXE-NL-PRE-ATT-1 Portable Receive Preamplifier-Attenuator is a Receive Only device. Attempting to transmit RF into this unit will cause damage that is not covered by warranty.
( 14 )
$175.99
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit is based on the design by Don Kirk, WD8DSB. Don's article on this antenna is published in the March 2021 issue of QST Magazine (used by permission). The DXE-NOISELOOP is a kit of parts to build this receive-only portable directional HF loop antenna, which measures only 48 by 24 inches plus 36 inches of mast-handle. It may be used while walking or stationary with your portable HF receiver. Oriented vertically, this loop antenna features a cardioid pattern at the horizon with a deep null of up to 30 dB rejection. It is an excellent tool for locating noise sources from 1.8 through 30 MHz and for low-noise, general coverage reception from the AM broadcast band through 30 MHz. An optional Preamplifier-Attenuator Unit, DXE-NL-PRE-ATT-1, may be attached to the loop mast handle for enhanced operations. An IC-705, a portable SW or a handheld HF receiver are excellent choices for searching for local noise sources with the NOISELOOP, around the neighborhood and even around your own home. This Portable Flag Antenna Kit includes everything needed to make the antenna: fiberglass tubing for the frame and handle, mounting plate, separate PC boards for the bifilar wound transformer and load resistor, antenna wire, coaxial cable with male BNC and stainless steel hardware. Simple hand tools and a solder iron are required for assembly. Included instructions detail assembly. This kit will typically take between 1 and 2 hours to build. The WD8DSB Portable Flag Antenna design has become a real game changer in direction finding of RFI on MF and HF frequencies, and you will also find it an invaluable tool when hunting RFI due to the following key features. *Unidirectional (unlike a tuned loop) *Broadband (unlike a tuned loop, excellent for AM DXing, SWL and Amateur) *Portable (easy to walk with while directional noise finding or HF Fox Hunting) Traditionally Flag antennas are large and designed for stationary use, but the idea for this antenna was to design a Portable Flag. It was designed to be the largest possible (to maximize gain) that would fit inside a car and it's still small enough to maintain a cardioid pattern up through 30 MHz. The portable Flag has an approximate dimension of 2 feet tall by 4 feet long which you (or a helper) can easily walk with while tracking down a signal. Unlike a tuned loop, the Portable Flag is a broadband antenna with unidirectional properties, and it's designed for direction finding from 1.8 to 30 MHz as long as an appropriate preamp is used. It's even useful for direction finding down in the AM broadcast band. The rear of the antenna produces a sharp null when pointed at the signal of interest and the sharp null is often used for direction finding versus using the broad peak which occurs when the front of the antenna is pointed at the signal of interest. Learn more about how to build this antenna kit by clicking on More Detail and the Documentation link for the Instruction Manual. Order your DX Engineering NOISELOOP Portable Receive Flag Antenna Kit here.
( 15 )
$159.99
DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas
New Name...Same Antenna! DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas are designed for low-noise reception of signals within the frequency range of 100-kHz to 30-MHz. Their integral, extra-high dynamic range, low-noise preamplifier is designed for minimum intermodulation distortion in the presence of very high-level signals that would normally overload most preamplifiers. Read more about the exclusive Clifton Laboratories design of the loop's RF-30 preamplifier by clicking "More Details" below. RF-PRO-1B Active Magnetic Loop Antennas, formerly known as the "Pixel Loop" and recently as InLogis, are now manufactured and serviced by DX Engineering. For Amateur Radio operators, AM DXers and Short-Wave Listeners, these active loop antennas are a great way to extend your listening ability. Add DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas to your radios and start hearing more signals with less noise! Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 26 )
$809.99
DX Engineering Receiver Guard Electronic RF Limiters
DX Engineering Receiver Guard RG5000HD Electronic RF Limiters are the best choice of inline devices to protect your receiver antenna inputs. The Receiver Guard is a receive antenna input limiter specifically designed to protect a sensitive receiver front-end against high levels of RF and potential damage. At the heart of each Receiver Guard is a highly effective electronic RF limiter covering 500 kHz to 150 MHz with an insertion loss under 0.15 dB up to 50 MHz and under 0.30 dB up to 150 MHz. The multi-stage design includes a gas discharge tube for maximum pulse energy protection. The DXE-RG5000HD rejects 10 watts of catastrophic receive antenna feedline RF while passing a maximum signal of about 87 dB over S-9, which is only 25 mw, a signal level that is well below the point of front end damage. Receiver Guards are a must for multiple radio contesting stations and they provide low-cost front-end "insurance." Use them in these common high-RF situations: - Receive antennas in very close proximity to transmit antennas - Field-day operations with many transmitters in close range - Multi-transmitter contesting sites - Neighboring Amateur and CB operators - Frequent high-power mobile encounters Extensively tested and proven in real-world stations, the Receiver Guard works for all radios and offers the ultimate performance required by the upper tier of transceivers tested to have the best narrow-spaced third-order dynamic range or published RMDR (Reciprocal Mixing Dynamic Range). These are passive electronic limiters, so competitive contesting stations use separate band filters in addition to the Receiver Guard. When there are high levels of RF on your receive antennas, the DX Engineering Receiver Guard generates far less harmonic noise than other limiters on the market, which allows your station to continue to operate safely and competitively. At normal HF signal levels the RG5000HD operates continuously with no effect on the performance of your station while providing the best possible protection for your radio. Here are key Receiver Guard features: * Keeps stray high levels of RF from damaging your receiver input * Ideal for separate 160 and/or 80 meter receive systems with large pulse and RF energy capture area * Uses state of the art components for maximum protection of receivers * Under 6 ns response time * Multi-Stage protection * Very low insertion loss * Uses BNC type connectors to avoid accidental connection to a transmit feedline * Has been developed and tested in world-recognized multi-multi contest station K3LR Specifications - DX Engineering Receiver Guard model DXE-RG-5000HD - Frequency Range: 0.5 through 150 MHz - Insertion Loss: < 0.15 dB up to 50 MHz, < 0.3 dB 50 MHz up to 150 MHz - VSWR: < 1.2:1 - Maximum Output Level at 10 W input: +14 dBm (0.025 W) - Maximum Power Handling: 10 W CCS (Continuous Commercial Service) - Device Impedance: 50 to 75 ohms, unbalanced - Connectors, Input and Output: BNC female Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. What happens if the receive antenna is extremely close to the transmit antenna, or there is an antenna support or other system failure that causes a high RF level to enter the receive antenna input? A DX Engineering Receiver Guard can save the day! Order yours now.
( 37 )
$119.99
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 3 )
$249.99
—
$1,999.92
DX Engineering XB-5 Hexx Beam HF Antenna
The DX Engineering XB-5 Hexx Beam is a lightweight directional five-band HF antenna for the 20, 17, 15, 12 and 10 Meter bands that is ideal for permanent or temporary installations. What are the benefits of this oddly shaped HF beam antenna? There are many, such as its small turning radius and full legal-limit power handling on all bands. But the most important are that the XB-5 Hexx Beam receives signals very well and transmits RF very efficiently. Its special configuration of full-size wire elements reject noise so more signals are heard. Months of development have culminated in this advanced antenna design for easier assembly, improved SWR and better bandwidth while maintaining excellent front-to-back performance. The DX Engineering XB-5 is our best Hexx Beam to date. DXE-XB-5 is the complete HF antenna package of specialized DX Engineering XB-5 Hexx Beam components; some are new and pre-assembled. These essential components include the patented* Hexx Hub and the Stainless Steel and PTFE Rigid Flat Feeder which is fully balanced with the Maxi-Core® 20 1:1 Current Balun and Mount. Also included are the all-new Heavy-Duty "Ice" Spreader Support Ropes with thimbles and stainless steel carabiners, better fiberglass Center Post and Spreaders, the Heavy-Duty Mast Mount, newly configured Element Wire Kits with the unique DX Engineering Wire Guides and innovative Element Spacer Insulators. The DX Engineering XB-5 Hexx Beam design has a number of important advantages over other Hex Beams or a mini-Yagi: - New, easy and faster assembly - fewer parts to speed completion of the antenna project - Pre-made 4.4 mm heavy duty "ice" support ropes with thimbles and stainless steel carabiners - High CMI Balun (1:1 5kW) and Mounting Bracket included - New Heavy-duty Mast Plate with DXE Saddle Clamps - Strong fiberglass without slits - Pre-sized and pre-drilled element spacer insulators designed for simple antenna assembly and tuning adjustment - Improved SWR band coverage - Small turning radius - the XB-5 Hexx Beam has a turning radius of 11' - Gain - 5 dBi (3 dBd), depending on band - similar to 2 element Yagi, far exceeding the performance of multi-band mini-beams - Front-to-Back – greater than 20 dB, depending on band - Wind balanced - Hexx symmetry reduces torque on the rotator - Light weight – about 25 lbs. fully assembled - Wind load – only 5 square feet wind surface - Can be turned with a light duty rotator - Performs well at low heights - good results at 25 to 35 feet above ground - Handles full legal limit power – no power restriction as on competing antennas - Low Noise results - approaches performance of closed loop antennas - Full length HF antenna elements - no lossy coils or traps - Five-Band Stainless Steel/PTFE Rigid Feeder System – balanced for best pattern - Requires no matching network - direct single 50 ohm coax feed The DX Engineering XB-5 Hexx Beam is one of the best performance values on the market for a directional HF antenna. *(US Patent No. 8,669,911, US Patent No. D 624,060, British Patent No. GB248003 B)
( 4 )
$1,247.92
DX Engineering LPFC-BNC Low Power Feedline Chokes
DX Engineering LPFC-BNC Low Power Feedline Chokes are intended to be placed in line with coaxial cable fed antennas and equipment used for portable operations, including POTA and SOTA activations. The DXE-LPFC-BNC coax wound toroid achieves an amazing common mode impedance (CMI) curve, with an RF choking capability that far exceeds the CMI of 'a-few-beads-on-coax' product that is offered by other suppliers. Actually, these "Low Power" Feedline Chokes can be used in any station that runs less than 250 watts SSB, 100 watts CW or Digital. ________________________________________ DX Engineering Low Power Feedline Chokes features and benefits: - A unique, lightweight form, with clear heat shrink over the choke* - Light enough to hang inline at the feedpoint of any portable HF antenna. - BNC female connectors for easy connection to portable antennas and gear. - Much higher CMI that other portable, low power chokes, especially across the 40 through 6 meter bands. - Frequency range of 1.8 through 54MHz. - RF Power Handling up to 250 watts PEP SSB, 100 watts CW and Digital (at SWR <2:1). - Recommended for general use to isolate either end of a coaxial cable. * Not intended for permanent outdoor use unless mounted inside a weatherproof enclosure. ________________________________________ These chokes are ideal for use at any HF transceiver or receiver antenna connection, portable, mobile or base. In most cases, DXE-LPFC-BNC prevents RFI, stops stray RF and noise on the feedline from getting into the receiver that would cover up weak signals, and improves efficiency of the antenna system. For any station, including POTA and SOTA, mobile and base, DX Engineering Low Power Feedline Chokes keep the RF controlled.
Not Yet Reviewed
$59.99
DX Engineering RPA-2 Modular Receive Preamplifiers
DX Engineering RPA-2 Modular Receive Preamplifiers are newly designed versions of the RPA-1 with internal slots for accessory modules. They accommodate the addition of the one optional plug-in module, such as the 75 to 50 ohm Impedance Transformer Module, or the Receiver Guard 5000HD Plug-In Module, or the DX Engineering Clifton Laboratories Z10020 AM Band Filter Module. DXE-RPA-2 preamps have very low internal noise and are optimized for the 300 kHz to 35 MHz range. They help you hear the weakest signals without artificially raising the noise. Meticulous craftsmanship and durable, robust components allow these preamplifiers to withstand high signal levels while providing superior dynamic range and third-order intercept performance that equals or exceeds most receiver and transceiver front-ends. RPA-2 Receive Preamplifiers have key features added, as requested by our tech-oriented customers and enthusiasts: - Internal slot accommodates the optional 75 to 50 ohm Impedance Transformer Module to accomplish typical receive antenna feedline to equipment transitions without losses -Also allows direct connection to 50 ohm receive antenna feedline BNC connectors with no transformer required - Internal slot for DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module – Front-end protection for the RPA-2 - Secure BNC female connectors and receive-system friendly F female connectors remain; both prevent accidental connection to transmitting devices with UHF connectors - A green LED indicates when DC power is present and the preamplifier circuit is engaged. - An ingenious positive-capture threaded-sleeve 2.1 mm power connector that ensures the DC power cannot be accidentally disconnected from the RPA-2. - Alternatively, a simple internal jumper change allows the RPA-2 to be powered by DC on the feedline While many other common preamplifiers suffer from harmonic distortion, RPA-2 Modular Receive Preamplifiers include our exclusive, advanced push-pull design that eliminates harmonic distortion. Their high quiescent current increases their ability to handle strong signals without distortion or overload. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 Vdc input. Please do not use a cheap wall transformer or noisy switching wall-wart to power these top-of-the-line preamplifiers. Indoor installation at the back of the radio is recommended for RPA-2. For those who want to place them in an enclosure at a receive antenna system, a handy internal jumper allows these new units to be powered on the coaxial cable. RPA-2 Receive Preamplifier Specifications: -Input and Output Connectors, female: BNC and F -Frequency Range: 300 kHz to 35 MHz -Gain: 16 dB, +/- 1.5 dB (over entire frequency range) -Output Third Order Intercept: 43 dBm -Noise Figure: 3.5 dB -One dB Compression Point: +26 dBm (400 mW output) -Dynamic Range, IM3: 110 dB or greater (500 Hz bandwidth) -Power Requirement: 12-18 Vdc, 140 mA max. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering RPA-2 Modular Receive Preamplifiers offer superior receiving results on crowded medium wave and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the advanced operational performance of DX Engineering Receive Preamplifiers. You will be able to pull in the weakest signals and snag that rare one, under the most difficult conditions, when you need it the most. Order your DX Engineering RPA-2 today!
( 14 )
$269.99
DX Engineering RTR-2 Modular Receive-Transmit Interfaces
DX Engineering RTR-2 Modular Receive-Transmit Interfaces provide the easiest and safest method for connecting a dedicated receive antenna to an HF transceiver that does not have a separate receive antenna input. Placed inline with the transceiver's antenna connector, the RTR-2 does the job of a 200 watt T/R relay using the amplifier keying line for failsafe protection, so your transmitted energy cannot go to the receive antenna. Three internal Plug-in Module option slots provide added features and protection: * DXE-RPA-2-PM Receive Preamplifier Plug-in Module * DXE-TRI-PM Transmit Receive Interrupter Plug-In Module * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-in Module DX Engineering RTR-2 Modular Receive-Transmit Interfaces allow the standard transceiver owner to enjoy the advantages of separate receive antennas. For the unswitched receive antenna (RX ANT) port on expensive transceivers, the RTR-2 interface also adds inexpensive failsafe protection. The receive antenna line can be opened or grounded with the optional DXE-TRI-PM Interrupter plug-in module. The RTR-2 is a very useful device for many applications, including: * Connection of external receiving antennas to transceivers lacking external antenna ports * T-R antenna switch for older equipment using separate transmitters and receivers * Interfacing antennas to older phasing or noise cancelling systems * Addition of a switchable receive preamplifier to any transceiver or transmitter and receiver combination * Excellent failsafe receiver protection for close-spaced transmit and receive antennas, without performance degradation of diode circuits of other devices. RTR-2 units feature a unique, failsafe connection method that prevents the hot switching and timing errors that are common on other transmit/receive relays. RTR-2 interfaces switch fast enough for partial break-in CW operation. There are many simple applications for the new RTR-2 and now internal modules can add dramatically improved reception of those really weak signals on the crowded HF bands! DX Engineering RTR-2 Modular Receive-Transmit Interfaces enable operators to enjoy improved reception with any low noise receiving antenna system. This shielded enclosure relay system provides a safe method of connecting a receive antenna, such as a Beverage, Active Receive system, or other receiving accessories to your radio. Major features that make the DX Engineering RTR-2 Receive Antenna Interfaces your best choice for a receive T/R system device: * New Status Indicating Color-changing LEDs * Three internal slots for new DX Engineering modules * New Key Line Out connector for Amplifier * New internal jumper for placing DC on the Receive Antenna feedline for Active or Loop receive antennas * Attractive and heavy stainless steel enclosure * 200 watts RF switching capability * Supports CW partial break-in * Main transmit antenna connector is SO-239 (UHF female) * Radio RF connector is SO-239 (UHF female) * Receive antenna input is 75 ohm F connector * Receive outputs are standard 75 ohm Type F connectors * Inputs are 50 ohm BNC or 75 ohm F (Optional transformer module available) * Safe switching--transmit antenna is always connected to transceiver on power-off * Hot switching lockout--disables receive antenna during transmit mode (Optional DXE-TRI-PM can be set to short the RX ANT line) * Versatile--allows inclusion of Optional RF preamplifiers and other plug-in modules * Simple 13.8 Vdc input for all operations An indispensable accessory for the DX enthusiast and useful for any Amateur's shack, DX Engineering RTR-2 Modular Receive-Transmit Interfaces can help you expand and improve your station's antenna connections and the protection of your equipment.
( 12 )
$375.99
DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits
DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits, DXE-MC20-FCM, provide current balance and feedline isolation on coaxial cables for all types of HF through 6 meter antennas including verticals, rotatable dipoles, directional beams and Yagi antennas. Intended for 50 ohm feedlines operated at low SWR, this combination of mounting plate bracket and effective 50 ohm RF choke handles full-legal-power-plus and provides higher common mode impedance (CMI) across a greater frequency range than competing feedline choke and line isolators and previous DX Engineering and Comtek models. High CMI across the AM Broadcast band and the HF/6M spectrum is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. With less noise and interference you will hear and be heard using a DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits. DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits bring new parts together to work on many types of antennas. They provide improved RF isolation and current balance at either end of the feedline and at the feedpoint of a vertical, a beam, rotatable dipole or other antenna feedline. This is a unique perpendicular choke mount that allows a beneficial separation between the ferrite of the choke and the antenna boom or mast, resulting in improved choking performance compared to a choke mounted on metal. The UV black high-strength polymer mounting plate provides additional isolation and holes for different mounting positions for the choke, horizontal or vertical. Stainless steel hardware is included to attach the plate to the stainless steel mounting bracket, which has laser cut holes for one of five optional DX Engineering Saddle Clamps to cover mast or boom sizes from 1 to 2 in. and 2.375 to 3 in. Click "More Detail" for additional information and click Suggested Parts for required optional items including one saddle clamp to fit your mast or boom and coaxial cable assemblies. Maxi-Core® 20 Feedline Chokes features high quality silver-plated PTFE dielectric SO-239 (UHF female) connectors. The SO-239 connector limits power handling to 5 kW or less at low SWR and reduced power at elevated SWR. These feedline chokes exhibit very low insertion loss and inherently low SWR. They are built into a convenient weather resistant NEMA enclosure with weep holes at all four corners of the "bottom" side of the enclosure, to vent properly when mounted vertically or horizontally for all types of antennas. Make your antenna play to its potential; reduce RFI and improve reception with DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits.
( 4 )
$207.98
DX Engineering High CMI Receive Feedline Chokes
DX Engineering High CMI Receive Feedline Chokes achieve exceptionally high isolation between the input and output connector shields to effectively block common-mode RF noise and unwanted signals that collect on 50 or 75 ohm receive antenna feedlines. Ongoing research and development by the design team at DX Engineering has produced two bidirectional Receive Feedline Chokes; a 50-ohm model with BNC female connectors and a 75-ohm model with Type-F female connectors. Both chokes cover the RF frequency range 100 kHz through 30 MHz. They exhibit very high common mode impedance* (CMI typically over 8,000 ohms across the 160, 80, and 40 meter bands) and feature DC pass capability up to 700 mA at 13.8VDC, with extremely low SWR and negligible insertion loss. Affordable DX Engineering High CMI Receive Feedline Chokes will be considered the best, most versatile receive chokes ever produced for typical low band receive antenna applications.
( 3 )
$59.99
—
$64.95
DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kits
DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kits, DXE-MC20-1-1BM, provide current balance and feedline isolation for HF through 6 meter verticals, rotatable dipoles, directional beams and Yagi antennas. Intended for 50 ohm feedpoint antennas that offer low SWR, this combination of mounting plate bracket and effective 1:1 RF choke balun handles full-legal-power-plus and provides higher common mode impedance (CMI) across a greater frequency range than competing balun models and previous DX Engineering and Comtek models. Their high CMI across the AM Broadcast band and the HF/6M spectrum is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. With less noise and interference you will hear and be heard using a DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kit. A similar kit was formerly known as the Vertical Feedline Current Choke. But, the Maxi-Core® 20 1:1 Balun and Mount Kit bring new parts together to work on many types of antennas. They provide improved RF isolation of the feedline and current balance at the feedpoint of a vertical, a beam or rotatable dipole. This is a unique perpendicular mount that allows a beneficial separation between the ferrite of the balun and the antenna boom or mast, resulting in improved choking performance compared to a balun mounted on metal. The UV black high-strength polymer mounting plate provides additional isolation and holes for different mounting positions for the balun, horizontal or vertical. Stainless steel hardware is included to attach the plate to the stainless steel mounting bracket, which has laser cut holes for one of five optional DX Engineering Saddle Clamps to cover mast or boom sizes from 1 to 2 in. and 2.375 to 3 in. Maxi-Core® 20 Baluns feature 1/4-20 stainless steel hardware and a high quality silver-plated PTFE dielectric SO-239 (UHF female) input connector. The SO-239 connector limits power handling to 5 kW or less at low SWR and reduced power at elevated SWR. These baluns exhibit very low insertion loss and inherently low SWR. Maxi-Core ® 20 Baluns are built into a convenient weather resistant NEMA enclosure with weep holes at all four corners of the "bottom" side of the enclosure, to vent properly when mounted vertically or horizontally for all types of antennas. Click "More Detail" for additional information and click Suggested Parts for optional items required, including one saddle clamp to fit your mast or boom, and a wiring kit or flexible copper strap to connect the balun to the antenna feedpoint terminals. Make your antenna play to its potential; reduce RFI and improve reception with DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kits.
( 4 )
$207.98
DX Engineering Bead Choke Standoff Kits
DX Engineering Bead Choke Standoff Kits bring a practical solution to a serious problem when ferrite chokes are placed directly onto the metal boom at the feedpoint of beam antennas. A number of Amateur Radio operators and antenna engineers have known for years about the superior choking function of many ferrite toroids beads placed directly on the coaxial cable, as compared to standard feedpoint baluns. A more recent revelation is that the proximity of ferrite beads on coax taped to the aluminum boom of the antenna drastically reduces their effectiveness. DX Engineering Bead Choke Standoff Kits are mounting systems, made of fiberglass or acetyl standoff rods (color varies), PVC carriers and stainless steel hardware, available in four versions. Two sizes of PVC cradle tubes handle two different types of RF bead chokes; 3/4 inch outside diameter (OD) ferrite beads on RG-400 size cable, and 1 inch OD ferrite beads on RG-213 size 0.405 in. coax cable. Each are offered with two different boom size clamps, 2 inch OD and 3 inch OD. Bead Choke Standoff Kits simply hold an RF bead choke and feedline 4 inches away from the metal beam antenna boom (or 4 inches away from the metal mast for a dipole). They maintain the optimal choking performance of ferrite beads on coax. Using DX Engineering Bead Choke Standoff Kits, ferrite bead chokes function at peak performance for these key results: • Prevent feedline radiation of RF • Preserve current balance for proper beam antenna pattern • Prevent feedline shield exterior collected noise and signals from entering the antenna and interior of the feedline, resulting in lower noise floor and enhanced reception The absolute superiority of RF chokes made of many beads on the feedline, over the traditional enclosure balun, is becoming better understood in Amateur Radio. They achieve the best possible RF isolation of the feedline from the antenna and provide completely balanced currents at the feedpoint. Plus, they provide quieter reception with reduction of common-mode noise. Keeping Bead RF Chokes away from metal preserves the optimal function of this method of antenna feedpoint current balance and isolation. This mechanical requirement is simple and practical with DX Engineering Bead Choke Standoff Kits.
( 3 )
$52.79
—
$65.99
DX Engineering Clifton Laboratories Z10000 Buffer Amplifiers
DX Engineering Clifton Laboratories Z10000 Buffer Amplifiers may be the products most often requested by radio experimenters and electronics enthusiasts. These are the very popular circuits, designed by Jack Smith, K8ZOA (SK), that are crucial for adding a SDR receiver and panadapter display capabilities to a receiver or transceiver which lacks that feature. The Z10000 Buffer Amplifier's high-input impedance can safely tap the early-stage broadband Intermediate Frequency (IF) signal from inside your radio and feed the buffered and amplified low impedance IF signal to your external SDR receiver. It can then produce a spectrumscope - waterfall display pattern of the receiver signals on a compatible tablet or monitor and PC that is running the appropriate third party SDR software. DX Engineering offers two Clifton Labs Buffer Amplifier Kits to add an IF output SMA connector to the rear panel of your radio: * The DXE-Z10000U-KIT is the Universal Buffer Amplifier Kit that covers 50 kHz to 100 MHz. This kit is designed for those willing to do an internal modification, and will output the IF signal of virtually any receiver or transceiver that has an IF in that range. However, the DXE-Z10000U-KIT can be used as a buffer and low-gain preamp between any low level RF devices that operate in that range. As a buffer, this circuit provides over 90dB of reverse isolation to protect the IF stages of the radio from possible birdies on an SDR receiver input. So, even if your radio has an IF output connector, the DXE-Z10000U-KIT may be used externally, with a user-supplied shielded metal enclosure, to be certain to maintain proper radio operation. * The DXE-Z10000K2-KIT is the Buffer Amplifier Kit specifically tuned to the 4.915 MHz IF signal of the Elecraft K2 transceiver. It offers the same high reverse isolation, plus the added benefit of a tuned IF input with a narrower bandwidth of operation and a potentially a lower noise floor on the output. Both Buffer Amp kits contain the updated, completely assembled and tested DX Engineering Z10000C PC Board with a nominal 6.5 dB gain, retaining all the benefits of the reliable original Z10000B boards. Both kits include our finished printed circuit board, required coaxial cables assemblies with special connectors, insulating materials, and hardware—all for an easier installation than ever before! A third party SDR receiver, software (typically free) and compatible tablet or PC and monitor are required to make use of the IF signal provided by the Z10000 Buffer Amplifier and see the signals that your old radio can hear. Due to the high number of specialized radio installations, no printed instructions are included with these buffer kits. Instructional web links are found on the part detail webpages. Installation web documents and videos are only available online. The legacy that was built by Jack Smith, K8ZOA (SK), with Clifton Laboratories, lives on with select products, exclusively from DX Engineering. NOTE: DX Engineering cannot provide electronic technical support of devices installed in user radios and is not responsible or liable for damages that occur to a user radio due to improper or erroneous techniques during the installation of this product. Unplug all electronic devices when working on them and observe all electrical safety and electrostatic discharge precautions when opening sensitive electronics. Modification of a radio should only be attempted by individuals with advanced experience on electronic circuit repair and operation.
( 24 )
$51.99
—
$61.99
DX Engineering HF QRP Bandpass Filters
DX Engineering HF QRP Bandpass Filters are designed to tightly confine both transmitted and receive signals to one specific Amateur band, these filters significantly reduce out of band noise, resulting in a noticeably lower noise floor and improved weak signal reception. In multi operator contest or portable operations, they deliver the essential isolation needed to eliminate image and harmonic interference, ensuring clean mono band performance even in close quarters environments. Each filter features a sharp roll off just outside the band edges, providing exceptional rejection of adjacent band signals and maintaining maximum operating efficiency for QRP applications. Offered for the 80, 40, 20, 15, and 10-meter amateur bands, they install easily in line with the coax feedline using the BNC connectors provided on each end. With power ratings of 20 watts SSB and 5 watts digital, they are ideal for QRP enthusiasts participating in multi operator events such as Field Day, POTA, and SOTA.
Not Yet Reviewed
$69.99
DX Engineering Reversible Beverage Systems
DX Engineering Reversible Beverage Systems basically allow two Beverage antennas to be switched to receive in opposite directions while sharing the same physical space. DXE-RBSA-1P Reversible Beverage Systems antennas provide two opposite "end-fire" directional patterns with excellent front-to-rear directivity and superior signal-to-noise ratio as compared to transmitting antennas. Dramatically improved long distance weak signal results may be achieved on MW and the 160, 80 and 40 meter bands, including shortwave bands, with receive-only Beverage antennas using wires that are typically only 350 to 800 feet long, depending upon the band of interest. The two-direction DXE-RBSA-1P Reversible Beverage Systems offer a space and installation advantage because two opposite single-wire Beverage antennas would require twice the length. DX Engineering Reversible Beverage Systems are immune to the strong signal overload and core saturation common in multi-transmitter contesting environments and are used by winning contest stations and low-band DXers around the world. These Reversible Beverage antennas have two "F" connectors; one "Away" port for the default end-fire receiving pattern off the end of the wire, and one "Toward" port for the opposite direction. The standard configuration of these systems has the "Toward" port terminated (75-ohm termination included), so both antennas share a common feedline. Applying a negative 10 to 18V DC to the feedline switches the system between the two antenna ports for reception in opposite directions. For simultaneous reception from opposing directions, each of the two feedlines can be run to separate receivers, with the termination load not used. You can build a 4-direction receive antenna system with two DXE-RBSA-1P Reversible Beverage Systems and one DX Engineering RLS-2 Two-Port Receiving Switch that also requires only one feedline! The optional DX Engineering Feedline Voltage Coupler, model DXE-FVC-1 is highly recommended to provide all of the required feedline voltage injection. Plus, the optional DXE-EC-4 BCD Control Console completes the system for four-direction switching right in the shack. DX Engineering Reversible Beverage Systems are optimized to use our optional 450 ohm ladder line for the antenna element. We strongly recommend using that type of "window line" because the consistent spacing of the antenna wires will produce the best operational results. However, the RBS will work with any 300-600 ohm 2-wire line. For best feed line results, DX Engineering highly recommends using our high quality flooded or quad-shielded 75-ohm coax with F-type compression connectors to ensure a weatherproof installation. Additional features include: * Broad operating range, 0.2 to 30 MHz * Fully isolated grounds prevent common-made noise and unwanted signals * 75 ohm design enables the use of high quality, low cost cable and connectors * RF shielded housing used for isolation and improved life * Directional Switching Voltage: nominal 12V AC or negative 12V DC, feedline injected * Directional Switching Current: less than 80 mA * Antenna impedance: 300-600 ohm (450 ohm recommended) * Feedline impedance: 50-75 ohm (75 ohm recommended) * RBSA-1FP Feed Point unit dimensions: 5.5 in. width x 3.5 in. depth x 1.5 in. height * RBS-1RT Reflection Transformer unit dimensions: 2.125 in. width x 2.125 in. depth x 1.125 in. height Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Reversible Beverage Systems offer the best DX reception and flexibility in high performance two-direction wire Beverage receive antennas. Get yours set up soon!
( 3 )
$335.98
DX Engineering Beverage Antenna System Combos
DX Engineering Beverage Antenna System Combos are single-wire single-direction Beverage antenna feed systems. These combos include DX Engineering's superb receive preamp and the Beverage antenna feedpoint transformer! The included BFS-1 transformer design makes them immune to the strong signal overload and core saturation. The isolated-winding matching transformer significantly increases the signal-to-noise ratio in Beverage and other high-impedance antennas. The included termination resistor is a special 470 ohm, 2 watt, non-inductive resistor that withstands nearby lightning strikes. Also included, the DXE-RPA-2 Modular Receive Preamplifier is the best low noise, receive preamps available… period. It is optimized for the 300 kHz through 35 MHz frequency range with an advanced push-pull amplifier design that eliminates harmonic distortion and it handles strong signals without distortion or overload. The DXE-RPA-2 Modular Preamp features one internal option slot for a plug-in module. Choose from the DXE-RG5000HD-PM Receiver Guard, the DXE-IT-PM 75 to 50 ohm Impedance Transformer, or use a RXFL Filter Adapter and a Receive Filter board for band pass, high pass or low pass filtering. Click "More Detail" for additional information. The "Documentation" tab contains links to associated files. SWLs and Radio Amateurs around the world have come to rely on the exceptional performance of DX Engineering products. Order one of these DX Engineering Beverage Antenna System Combos to get excellent MW and HF reception with your Beverage antenna.. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$385.98
DX Engineering TFS4 Series B Transmit Four Square Systems
DX Engineering TFS4 Series B Transmit Four-Square Systems bring together the highest level of engineering excellence with the practical realities of operator convenience and ease of installation. These four-square hybrid systems are available in versions for the 160, 80, and 40 meter bands. They can be easily dropped into your quarter-wave spaced vertical 4-antenna array to provide optimum directional control. They allow the operator to receive or transmit with 5.5 dB gain in any one of four directions with a 20+ dB front-to-back ratio for interference reduction from unwanted directions. You can also switch to a single Omni-directional pattern with a push of a single button. This combination permits you to listen "all-around," unhindered by pattern nulls, and then select the best direction for signal reception and noise rejection. TFS4 Series B Transmit Four Square Systems are designed for use with four monoband vertical antennas placed at the corners of a square that is one-quarter wavelength on a side. The vertical element must be ungrounded and resonant in the desired band, and should be directly base-fed by the coaxial cable phasing lines from the centrally located controller (shunt-fed towers or radiating elements cannot be used). DX Engineering has several vertical antennas that are well suited for this application. Above all, a properly designed and installed radial system is necessary for top antenna performance, whether it's a single vertical or a full array. DX Engineering strongly recommends our optional Q75- series quarter wavelength cables constructed from our own high quality DXE-11U coax. It features a waterproof PE jacket, foam dielectric and has a velocity factor of 82 percent. These cables are electronically pruned to a precise electrical length derived from your choice of center operating frequency, terminated with hand-soldered silver-PTFE PL-259 connectors and weather-sealed with shrinkable tubing. Finally, each cable is tested for high voltage breakdown for maximum reliability and power handling. Since the transmit power is divided by the controller, the coaxial cable can handle QRO power with ease. If you already have a four-square array with a hybrid controller and would like to upgrade to improved performance and the Omni feature, the DX Engineering TFS4 Series B Transmit Four Square Systems are a direct transplant. BCD logic switching allows for the use of a 4-wire control cable to perform the necessary switching functions when powered by the included control console. Features: * Classic hybrid design is easy to install * Four directions plus Omni for versatile operation * 5 kW CW power rating for high reliability * Hot switching lock-out to disable amplifier while switching * Drop-in replacement for COMTEK systems * Proven DX Engineering RF relays for high performance * RF Shielded, high impact thermoplastic cover offers unique protection * Relays cycle during Power-On to ensure clean contacts Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Four-square systems work great! DX Engineering TFS4 Series B Transmit Four-Square Systems provide the heart of a modern phased array.
Not Yet Reviewed
$807.98
—
$831.98
DX Engineering Receive 8 Circle Array Controllers
DX Engineering RCA8C-1 Receive 8 Circle Array Controllers are the highly sophisticated switch controller relay units from the Eight Circle Array Systems--the receiving systems that use time delay phasing--rather than the conventional narrow-band, frequency-dependent phasing, to provide eight 45 degree spaced directional patterns. The RCA8C time delay phasing is directivity-optimized to produce wider and deeper rear nulls and a narrower main lobe. The result is that noise and undesirable signals are greatly reduced for a superior front-to-rear ratio (F/R). Better control of phase and currents provides a cleaner pattern with the Receive 8 Circle than is available with vertical antenna transmit arrays. DX Engineering Receive 8 Circle Array Controllers are designed to be used with eight identical vertical active or passive vertical elements, symmetrically spaced in a large circle, to provide switching for an 8-direction receiving antenna system. Passive elements will generally provide you with a monoband receiving system. Finally, these systems offer greater reliability in receiving applications. Receive Eight Circle Array Controllers use sealed relays sized for receiving applications with silver contacts to prevent oxidation and contamination. Most transmitting four-square switches use large open-frame relays where the contacts are exposed to the air, which can lead to contamination. Relays with brass contacts can oxidize, leading to poor conductivity. Receive Eight Circle Array controllers feature: * W8JI design * Operation from 100 kHz to 30 MHz * Excellent directivity for better signal-to noise ratio * Switching console provides eight 45 degree spaced directions * Less physical space and maintenance required than phased Beverage antennas * Low current DC powered control console allows system operation without AC power mains The optional DX Engineering Eight Circle Receive Short Element Active Vertical Antenna Package, DXE-RSEAV-8, offers excellent receiving performance from 100 kHz to 30 MHz, while using only a 8.5 ft. (2.6m) aluminum vertical antenna elements. A unique design makes the Receive Eight Circle Array System vastly superior to traditional active vertical antennas in both strong signal handling and feedline decoupling. This results in significantly better weak signal reception due to lower spurious signal interference and reduced noise. DX Engineering RCA8C Receive 8 Circle Array Controllers are the foundation of your Eight Circle Array!
Not Yet Reviewed
$499.99
DX Engineering TWIG QRP 4:1 Current Baluns
The DXE-TWIG-4-1C QRP Current Balun is designed to be used as the feedpoint of a very low power (QRP) Off Center Fed dipole (OCF) antenna. Ideal for use during outdoor adventures such as POTA® or SOTATM, or any portable operation. The TWIG-4-1C incorporates a 4:1 transformer to convert the OCF antenna impedance of 200-ohms to the desired 50-ohms to match the coaxial cable feedline. It also has a 1:1 feedline choke, to prevent current imbalance, detuning, and to help prevent the addition of unwanted noise. The connector is a BNC female and mates with the recommended coax and most low power (QRP) transceivers. When properly installed and the element wire is properly tuned, you should not need an external tuner. This reduces the need to bring more equipment than is necessary or a portable operation and provides higher efficiency of your output signal and instant band changes. The antenna shown in this manual was designed and tested using the optional 24 AWG wire such as CEW-VIZ24-YEL100 stranded copper, PVC insulated, high visibility yellow antenna wire. The BNC connectors coax cable is recommended to be at least 25 to 35 feet in length. The antenna can be installed in different configurations of wire lengths for various band selections. For example, a very common TWIG QRP OCF for 40, 20, 15 and 10 meters has one 57 ft. dipole wire and the other wire is 12 ft. See the chart in the Instruction Manual linked below for details. This is a low power (QRP) antenna system balun which handles only 25 Watts on SSB, 10 Watts on CW and 5 Watts on digital mode when antenna SWR less than 2:1, without the use of an antenna tuner.
Not Yet Reviewed
$69.99
DX Engineering TWIG Broadcast Interference Filter
Improve the performance of your QRP POTA or SOTA station with the DX Engineering DXE TWIG BCFIL Broadcast Interference (BCI) Filter. Engineered specifically for low power amateur radio applications, this compact module effectively attenuates strong AM broadcast band signals below the 80 meter amateur band. By suppressing these out of band signals, the filter helps lower your receiver's noise floor, resulting in cleaner, more reliable reception of weak amateur radio signals. The DXE TWIG BCFIL is equipped with BNC female connectors for quick, in line installation in the field. Ideal for portable, field, and low power fixed station use, it provides an effortless way to reduce unwanted broadcast interference without adding complexity to your station setup. Features: • Blocks strong AM broadcast band and 1.8 MHz signals below the 80 meter amateur band • Improves receiver noise floor and enhances reception of desired signals • Designed for low power transceivers • Compact in line module with BNC female connectors for easy installation • Ideal for portable POTA and SOTA, mobile, and fixed low power stations Power Rating: For QRP use only — maximum 20 watts PEP. Not suitable for high power transceivers.
Not Yet Reviewed
$49.99