Availability
12 Results Found For "in-line"
DX Engineering Guy Line End Caps
DX Engineering Guy Line End Caps are designed to work with silicone sealer to cap off and seal your cut Phillystran guy line. The end caps are manufactured from high quality vinyl material and are available in different sizes to fit your specific guy line diameter.
( 9 )
$19.99
DX Engineering Type F Coaxial DC Blocks
DX Engineering Type F Coaxial DC Blocks have a male F connection for the equipment and a female F connection for the antenna line. When inserted into the line in either direction, they block DC current from passing through while permitting RF signals to flow. These units effectively block DC current from entering where it's not wanted—on antenna lines where DC powers other devices. The blocks will keep DC out of your receiver input! Their straight, inline form factor is perfect for most applications. Use these DC blocks at frequencies from 5 to 2,500 MHz! For example, they're ideal for isolating amplified Sirius/XM antenna voltage from your receiver. They easily handle up to 24 Vdc. Block that DC! Order your DX Engineering Type F Coaxial DC Blocks today.
Not Yet Reviewed
$11.99
DX Engineering NPA RF Attenuators
DX Engineering NPA RF Attenuators reduce the amount of signal carried within coaxial cables. This signal attenuation is sometimes needed to ensure proper receiver operation. When amplified antennas and inline amplifiers are used with short cable runs, it's possible to have too much signal arriving at the radio. Excessive signal may over-drive the receiver and create distortion or self-generated interference. When this happens, knocking the signal down a bit is the best remedy. DX Engineering RF Attenuators are Non-Passing Attenuators (DC blocking) in 10 or 20 dB attenuation levels. They may be combined for attenuation levels beyond 20 dB; however, this is very rarely needed. Operation is from 500 kHz to 2.4 GHz. When you suspect that you have too much signal reaching your radio, grab one of these DX Engineering NPA RF Attenuators!
( 1 )
$11.99
DX Engineering Grounding Clamps
DX Engineering Grounding Clamps are used to connect wire grounding conductors of AWG 2 through 10 to a ground rod, tower leg or grounded pipe. These clamps are manufactured from cast bronze, a highly conductive copper alloy, and include high quality 1/4-20 stainless steel screws for maximum longevity and durability. These clamps also accept the stud from our IS-RCT control line protectors, to provide the proper protection of rotator control lines at the base of a grounded tower. Please note that pipe is measured by ID, not OD. For example, 1-1/4 pipe is much larger than 1-1/3 in. OD. DX Engineering Grounding Clamps are available in two sizes, to fit your grounding project. These are great general purpose grounding clamps to have on hand for future projects, so add a few to your order today!
( 8 )
$16.99
DX Engineering Heavy-Duty Saddle Clamps
Our tradition of continuous innovation was evident with the introduction of the DX Engineering Heavy-Duty Saddle Clamp line. DX Engineering set new standards over a decade ago with the introduction of the industry's best clamps for mounting antennas and element tubing. Featuring superior gripping power, our new Heavy-Duty Saddle Clamps are available in six different sizes, to fit tubing with Outside Diameter (OD) inch sizes of 0.75, 1.00, 1.25, 1.50, 1.75, and 2.00. Commercial and industrial engineers and installation technicians all over the world have discovered a diverse range of applications for DX Engineering Heavy Duty Saddle Clamps. DX Engineering Heavy Duty Saddle Clamps are designed to be used where maximum torque handling is required on aluminum, steel or stainless steel tubing. Conceived of by builders of large and heavy Yagi antennas and Log Periodic arrays, these clamps are made in sizes that securely fit the outside diameter of tubing for mounting to a flat plate or surface. Their wide gripping surface equals superior clamping power! Perfect for antenna construction and mounting, or wherever standard U-bolt saddle clamps and other torque-control products have proven inadequate, our Heavy Duty Saddle Clamps provide excellent grip on booms, masts and element tubing. Unlike stamped or machined-type clamps, Heavy Duty Saddle Clamps are cast from a rugged aluminum alloy that grips tubing with a special textured surface and are sized for an incredibly secure fit that resists torque, wind and weather. Heavy Duty Saddle Clamps include two cast aluminum saddles (two halves) and a stainless steel reinforcement plate for high strength and superior corrosion resistance. Due to the wide diversity of clamping applications where Heavy Duty clamps are beneficial, mounting hardware is NOT included. However, a complete line of Armor-Coated and Stainless Steel Hex Bolt Hardware Sets are available for top performance in most mounting applications. Typical Heavy Duty clamp mounting applications on a 1/4 in. plate require a minimum length bolt set, as indicated in the chart, linked in "More Detail…," and displayed in the "Required Parts" tab. For larger tubing attachment applications with ultimate gripping strength, DX Engineering Super Duty Saddle clamps are also available for 2.0, 2.5 and 3.0 in. O.D. sizes. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Plan your next project with the best clamps available... period. DX Engineering Heavy Duty Saddle Clamps are ready to provide superior performance for your antenna, mast or other tubing mounting application.
( 11 )
$10.49
—
$19.99
DX Engineering Utility Tool Cases
DX Engineering Utility Tool Cases offer many uses. These rugged molded plastic cases are lined with low-density convoluted foam, which conforms to the shape of the items stored inside. These cases have two snap latches and are designed to be secured with your padlock through the handle area. Keep your tools and other handheld valuables out of sight, secure, and protected against impacts with DX Engineering Utility Tool Cases.
( 4 )
$14.99
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$17.49
DX Engineering Electronic Protection Components
DX Engineering Electronic Protection Components may be used in a variety of electronics and radio applications. These are wire lead components that can be used on circuit boards or in multi-purpose connection devices. Choose from the components listed for detailed specifications: DXE-MOV-82VDC-10 Metal Oxide Varistor, Surge Protector, max. 82VDC/50VAC Pack of 10 DXE-GDT-4KV-5 Gas Discharge Tube, Surge Arrestor, 4kV, Pack of 5 DXE-TVS-1500-10 ESD Suppressor, TVS Diode, Bidirectional, 17VDC max., Pack of 10 DXE-CAP-PT1UF-10 Capacitor, Ceramic, 0.1uf, 1kV DC, RF Bypass, Pack of 10 ---------------------------------------------------------------------------------------------------------------------------------- This series of protection components are well suited for the DXE-CLTB Control Line Terminal Board that provides a flexible and simplified approach to control line surge protection. The DXE-CLTB is a small, 3 inch square printed circuit board (PCB) with four ten-wire compression screw terminal blocks that handle from 14 to 26 AWG conductors and up to 10A. The two outer terminal blocks are for input and output of the control wires and the two 45 degree angled ten-wire compression screw terminal blocks are for connecting electronic surge protection components. This provides for the choice of components to install between the control line and ground to provide shunt protection. Metal Oxide Varistor (MOV), Gas Discharge Tube (GDT), EMP Suppressor TVS Diodes, RF Bypass Capacitors and other wire lead components are easily connected between the control lines and ground. For effective protection wherever shunt devices are used, a low impedance ground is critical. The DXE-CLTB Control Line Terminal Board has four corner grounding screw holes for mounting on metal standoffs to a metal grounding panel inside an enclosure. DXE-CLTB-M Control Line Terminal Board includes a 10-pack of MOVs.
( 1 )
$11.99
—
$15.99
DX Engineering Wire Antenna End Insulators
DX Engineering Wire Antenna End Insulators are so unique that they are patented. They feature a unique serpentine wire grip for DX Engineering's insulated antenna wires and for our high-strength, high-power 300 ohm ladder line when used as a folded dipole. The serpentine wire grip and loop method is strong enough to support the antenna wires with no soldering of the wire required. This allows for fast and easy field adjustments of antenna length! The DXE-UWA-END-KIT includes eight of these unique insulators, which make them ideal add-on package to create multiple wire fan dipoles from a single UWA-KIT. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Many hams enjoy building, testing and experimenting with wire antennas. Make your own experimentation easier with DX Engineering Wire Antenna End Insulators!
( 32 )
$13.99
DX Engineering Glass Antenna Insulators
Sometimes the oldest stuff turns out to be the best. Our exclusive DX Engineering Glass Antenna Insulators hearken back to the earliest years of "wireless" transmissions. Because Irish ship builders of the day pronounced "double" as "dooble," these insulators were once known as "glass doobies" due to their tempered-glass material and double-ended form. Glass insulators offer the highest of electrical insulation properties, strength and resilience available in any insulator of its size. There will be no signal bleed off with these little glass wonders! DX Engineering's DXE-TGI-2 end insulators are 3.69 in. long with 1.125 in. diameter double ends. Each smoothed and rounded end has a 5/16 in. (0.3125 in.) hole that will accommodate many wire and rope sizes without chafing. Their tensile strength and resistance to arcing will withstand almost any wire-antenna use within the Amateur Radio service, domestic or abroad. Since these are end insulators, they are sold as a pair. These are not toy-like models or replica insulators; these are fully functional, high strength glass insulators with excellent RF properties! But, that is not to say that they aren't gorgeous and worthy of showing off! They certainly are perfect for display as a radio room decoration or as a living area conversation piece. Very smooth and pleasing to the touch, these are attractive glass insulators that make a fantastic gift for the ham who thought he had everything! Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. In this instance, some interesting information on "Glass Doobies." Bring back a bit of the essence of the Amateur Radio of yesteryear in your wire antenna construction. These glass insulators are actually quite striking in their appearance. Order DX Engineering Glass Antenna Insulators and gain the benefits of using a material that has provided the best wire-antenna insulation for more than a century!
( 21 )
$15.99
DX Engineering HF Vertical Antenna Replacement Parts
DX Engineering's line of HF Vertical Antenna Replacement Parts are offered for you to perform antenna maintenance or repair. DX Engineering has the antenna parts that you need!
( 1 )
$17.49
DX Engineering Weatherproofing Kits
DX Engineering Weatherproofing Kits weatherize your outdoor connections and prevent moisture entry and corrosion with vapor wrap and high quality electrical tape. When your non-weather resistant equipment needs to be mounted outdoors, these weatherproofing kits provide needed protection. Use these kits to protect lightning protectors, coaxial connections, antenna joints, steel hardware, junction boxes and just about anything you can wrap with tape by using these kits. The non-conductive malleable vapor wrap sealant is water-impermeable and withstands temperatures from minus 65 degrees F to plus 180 degrees F without cracking. Choose from Standard, Upgraded or Ultimate kits with different grades of vinyl tape. The WK-PRO Kit has more vapor wrap material and five rolls of tape for large projects. See each kit's detailed description. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Reliable waterproofing is important to protect equipment and cable connections from damage caused by moisture penetration. Protect your equipment, handle extreme temperatures, and remain unaffected by water and UV sun rays with DX Engineering Weatherproofing Kits.
( 19 )
$15.99