Selected Filters


Availability


13 Results Found For "Choke"

Part Groups

Results 1 - 13 of 13

DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes

Introducing DX Engineering "Maxi-Core® 20" Baluns and Feedline Chokes. They reduce or eliminate currents on the outside of your feedline allowing you to hear and to be heard much better. They keep more RFI/BCI out of your antenna and receiver and transfer more of your transmitted signal to the antenna for higher efficiency, the best antenna pattern and maximum performance. Signaling a new era of RF performance across the 1.8 to 54 MHz frequency range, DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes handle full-legal-power-plus and provide higher common mode impedance (CMI) across a greater frequency range than competing models and even previous DX Engineering and Comtek models. Years of R&D coupled with major advancements in test equipment and techniques combined with custom ferrite materials have allowed our engineering team to design the DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes. Maxi-Core® 20 Baluns and Chokes have high CMI across the AM Broadcast band and the HF/6M spectrum, which is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. Hear and be heard with DXE Maxi-Core® 20 Baluns and Feedline Chokes. Choose superior performance from these models: * DXE-MC20-1-1 Maxi-Core® 20 - 1:1 Current Choke Balun - For all HF-6m balanced antennas with a 50 ohm feedpoint, including resonant dipoles, loops, Yagis, beams, etc. * DXE-MC20-FC Maxi-Core® 20 - 1:1 Feedline Choke – This high CMI line isolator is perfect for use in line on 50 ohm coaxial feedlines, at the antenna, tower or shack end of the feedline. * DXE-MC20-1-1T Maxi-Core® 20 - 1:1 Current Choke Balun – This 1:1 "T" model is for force feeding antennas with a tuner. Use it at the end of ladder line of any impedance or mounted on a coax fed non-resonant antenna. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-C4-1 Maxi-Core® 20 - 4:1 Current Choke Balun is for use on antennas with a 200 ohm feedpoint and at the end of any impedance ladder line, especially on antenna systems with higher impedance. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-V4-1 Maxi-Core® 20 - 4:1 Voltage Balun is a 200 ohm to 50 ohm transformer for use on random long-wire and OCF antenna applications. This true voltage balun is intentionally designed with low CMI for antennas that need a transformer without RF choking for easier antenna tuner operation and it tolerates elevated SWR. Maxi-Core® 20 Baluns and Feedline Chokes are built into a convenient weather resistant NEMA enclosure that is mounted easily with optional brackets. They feature 1/4-20 stainless steel hardware and a high quality silver-plated PTFE dielectric SO-239 (UHF female) input connector. The SO-239 connector limits power handling to 5 kW at low SWR and reduced power at elevated SWR. These baluns and the feedline choke exhibit very low insertion loss and inherently low SWR. Optional mounting brackets are available for use on wire antennas or for verticals, Yagi and beam antennas. See the Suggested Parts tab after clicking "More Detail" on the model of interest. Combination packages that include balun or choke and mounting bracket are also available.

4.9 out of 5 stars ( 143 )

$141.99

—

$169.99

DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits

DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits, DXE-MC20-FCM, provide current balance and feedline isolation on coaxial cables for all types of HF through 6 meter antennas including verticals, rotatable dipoles, directional beams and Yagi antennas. Intended for 50 ohm feedlines operated at low SWR, this combination of mounting plate bracket and effective 50 ohm RF choke handles full-legal-power-plus and provides higher common mode impedance (CMI) across a greater frequency range than competing feedline choke and line isolators and previous DX Engineering and Comtek models. High CMI across the AM Broadcast band and the HF/6M spectrum is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. With less noise and interference you will hear and be heard using a DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits. DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits bring new parts together to work on many types of antennas. They provide improved RF isolation and current balance at either end of the feedline and at the feedpoint of a vertical, a beam, rotatable dipole or other antenna feedline. This is a unique perpendicular choke mount that allows a beneficial separation between the ferrite of the choke and the antenna boom or mast, resulting in improved choking performance compared to a choke mounted on metal. The UV black high-strength polymer mounting plate provides additional isolation and holes for different mounting positions for the choke, horizontal or vertical. Stainless steel hardware is included to attach the plate to the stainless steel mounting bracket, which has laser cut holes for one of five optional DX Engineering Saddle Clamps to cover mast or boom sizes from 1 to 2 in. and 2.375 to 3 in. Click "More Detail" for additional information and click Suggested Parts for required optional items including one saddle clamp to fit your mast or boom and coaxial cable assemblies. Maxi-Core® 20 Feedline Chokes features high quality silver-plated PTFE dielectric SO-239 (UHF female) connectors. The SO-239 connector limits power handling to 5 kW or less at low SWR and reduced power at elevated SWR. These feedline chokes exhibit very low insertion loss and inherently low SWR. They are built into a convenient weather resistant NEMA enclosure with weep holes at all four corners of the "bottom" side of the enclosure, to vent properly when mounted vertically or horizontally for all types of antennas. Make your antenna play to its potential; reduce RFI and improve reception with DX Engineering Maxi-Core® 20 Feedline Choke and Mount Kits.

5.0 out of 5 stars ( 4 )

$207.98

DX Engineering Ferrite Bead Choke Kits

DX Engineering Ferrite Bead Choke Kits, DXE-FBC, provide the components for the simplest and most effective technique of creating RF isolation at an antenna feedpoint or feedline termination. Covering the frequency range 1.8 to 54 MHz, these 40 toroidal mix-31 solid ferrite beads, installed on a user supplied coaxial cable (prior to connector installation*), to build an RF choke with a very high Common Mode Impedance (CMI) over a very wide frequency range. This is the same choke that world-class contest and DX stations install. Given the simplicity and raw performance of this 40-bead choke, its comprehensive RF features and benefits should become familiar to every radio amateur and antenna experimenters.   * Yes!, the superior overall performance of the DXE-FBC Ferrite Bead Choke completely offsets the trouble of cutting off a coaxial connector, installing the kit, and then installing a new connector. It really is that good! 

5.0 out of 5 stars ( 4 )

$152.99

DX Engineering Maxi-Core® High-Power Multi-Band UNUNs

DX Engineering High-Power Multi-Band UNUNs with Maxi-Core® technology allow your antenna to perform to its fullest potential and reduce stress on your equipment. These specially tuned UNUNs, designed for non-resonant vertical antenna applications, operate more efficiently than similar competitive products. Lesser products may burn up easily on lower bands with QRO power levels. DX Engineering high-power UNUNs are specifically designed for applications with 43 ft. non-resonant, multi-band antennas, ensuring the best efficiency from your antenna and transmission line/tuner installation. The results are minimizing the additional transmission line losses caused by abnormally-high SWR. DX Engineering Maxi-Core® High-Power Multi-Band UNUNs can be added to any existing 43 ft. antenna installation or used to replace an older competitive UNUN for a performance increase. The UN-43-R includes mounting bracket and feed-point connections braids. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. All non-resonant vertical antennas present high SWR to their feed lines. Deal with it! Order DX Engineering High-Power Multi-Band UNUNs!

5.0 out of 5 stars ( 13 )

$201.99

DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kits

DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kits, DXE-MC20-1-1BM, provide current balance and feedline isolation for HF through 6 meter verticals, rotatable dipoles, directional beams and Yagi antennas. Intended for 50 ohm feedpoint antennas that offer low SWR, this combination of mounting plate bracket and effective 1:1 RF choke balun handles full-legal-power-plus and provides higher common mode impedance (CMI) across a greater frequency range than competing balun models and previous DX Engineering and Comtek models. Their high CMI across the AM Broadcast band and the HF/6M spectrum is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. With less noise and interference you will hear and be heard using a DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kit. A similar kit was formerly known as the Vertical Feedline Current Choke. But, the Maxi-Core® 20 1:1 Balun and Mount Kit bring new parts together to work on many types of antennas. They provide improved RF isolation of the feedline and current balance at the feedpoint of a vertical, a beam or rotatable dipole. This is a unique perpendicular mount that allows a beneficial separation between the ferrite of the balun and the antenna boom or mast, resulting in improved choking performance compared to a balun mounted on metal. The UV black high-strength polymer mounting plate provides additional isolation and holes for different mounting positions for the balun, horizontal or vertical. Stainless steel hardware is included to attach the plate to the stainless steel mounting bracket, which has laser cut holes for one of five optional DX Engineering Saddle Clamps to cover mast or boom sizes from 1 to 2 in. and 2.375 to 3 in. Maxi-Core® 20 Baluns feature 1/4-20 stainless steel hardware and a high quality silver-plated PTFE dielectric SO-239 (UHF female) input connector. The SO-239 connector limits power handling to 5 kW or less at low SWR and reduced power at elevated SWR. These baluns exhibit very low insertion loss and inherently low SWR. Maxi-Core ® 20 Baluns are built into a convenient weather resistant NEMA enclosure with weep holes at all four corners of the "bottom" side of the enclosure, to vent properly when mounted vertically or horizontally for all types of antennas. Click "More Detail" for additional information and click Suggested Parts for optional items required, including one saddle clamp to fit your mast or boom, and a wiring kit or flexible copper strap to connect the balun to the antenna feedpoint terminals. Make your antenna play to its potential; reduce RFI and improve reception with DX Engineering Maxi-Core® 20 1:1 Balun and Mount Kits.

4.75 out of 5 stars ( 4 )

$207.98

DX Engineering Balun Upgrade Kits

DX Engineering Balun Upgrade Kits provide the superior performance of a 1:1 DX Engineering Maxi-Core® 20 Balun, mounting bracket, hardware and clamps for your antenna update. Maxi-Core® 20 Baluns keep more RFI/BCI out of your antenna and receiver and transfer more of your transmitted signal to the antenna for higher efficiency, the best antenna pattern and maximum performance. They handle full-legal-power-plus and provide higher common mode impedance (CMI) across a greater frequency range than competing models and previous DX Engineering and Comtek balun models. DX Engineering Balun Upgrade Kits include: - DXE-MC20-1-1 Maxi-Core® 20 - 1:1 Current Choke Balun - For all HF-6m balanced antennas with a 50 ohm feedpoint, including resonant dipoles, loops, Yagis and beams. - DXE-BMB-4P Balun Mounting Bracket, For Maxi-Core® 20, with Poly-Resin Plate and Stainless Steel Hardware - DXE-BALUN-WK DX Engineering Balun Wiring Kits - Wire, Terminal and Hardware for antenna connection - DXE-ECLS-150 or DXE-ECLS-200 Stainless Mounting Clamps with Studs – One pair of studded band clamps with Stainless Steel Hardware, for antennas with 1.50 in. boom or mast or up to a 2.00 in. boom or mast. Maxi-Core® 20 Baluns and Feedline Chokes are built into a convenient weather resistant NEMA enclosure that is mounted easily with optional brackets. They feature 1/4-20 stainless steel hardware and a high quality silver-plated PTFE dielectric SO-239 (UHF female) input connector. They have weep holes at all four corners of the "bottom" side of the enclosure, so they work properly for vertical or horizontal mounting for all types of antennas. The SO-239 connector limits power handling to 5 kW at low SWR and reduced power at elevated SWR. These baluns exhibit very low insertion loss and inherently low SWR. When it is time to refurbish your Yagi, beam or rotatable dipole, purchase DX Engineering Balun Upgrade Kits to use the best 1:1 baluns for your antennas.

5.0 out of 5 stars ( 1 )

$226.96

—

$227.96

DX Engineering Dual Impedance Antenna Transformers

DX Engineering Dual Impedance Antenna Transformers are dual ratio UNUN (unbalanced to unbalanced line) transformers. They're great for coupling your 50 ohm coax to an antenna with a feed point impedance of either 25 or 12.5 ohms, typically found at HF mobile antennas. DX Engineering Dual Impedance Antenna Transformers are ideal for antennas that have been enhanced with a Hot Rodz capacity hat. These transformers are housed in an aluminum enclosure and use silver plated PTFE SO-239 connectors. Many mobile HF antennas are naturally between 10 ohms and 36 ohms at resonance. With 10 ohms at a 50 ohm feed point the resulting SWR is 5:1! Likewise, 36 ohms yields a 1.4:1 SWR. Matching at 1.4:1 isn't too bad, but 5:1 is definitely an issue. DX Engineering MM-1 Dual Impedance Antenna Transformers are ideal for adjusting the impedance mismatch in your HF mobile! When the natural resonant impedance of the antenna is at 30 ohms or below, the MM-1 mobile unun can provide the needed match. With a 50 ohm input, it provides a 25 ohm port and a 12.5 ohm port to facilitate mobile HF matching. Let's say that your antenna analyzer indicates a resonant antenna impedance of 22 ohms. Your SWR without an MM-1 would be 50/22 or 2.27:1. That's enough to cause considerable power rollback in most modern HF rigs. Using the MM-1 25 ohm port, your SWR would be 25/22, or 1.14:1. That's a very significant improvement! Many hams are using antenna analyzers to adjust mobile HF antennas. When a mismatch is indicated at resonance, a DX Engineering MM-1 Unun can solve the problem! Power handling capability depends on the match: * Using the 25 ohm to 50 ohm port, with SWR below 2:1 on the 50 ohm side, -- 750 watts PEP * Using the 12.5 ohm to 50 ohm port, with SWR below 2:1 on the 50 ohm side, -- 500 watts PEP Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Antenna analyzers are becoming more common. Buy or borrow one to check the impedance of your mobile antennas. Then get DX Engineering Dual Impedance Antenna Transformers to get the best match and highest efficiency you can!

5.0 out of 5 stars ( 2 )

$184.99

DX Engineering RG-8X Hi-Viz Orange 50-ohm RF Choke Coaxial Cable Assemblies

DX Engineering RG-8X Hi-Viz Orange 50-ohm RF Choke Coaxial Cable Assemblies are the most flexible and lowest loss high-quality coaxial cable assemblies on the market. Assembled with fifteen Mix -31 ferrite beads under weather-sealed heat shrink, these DXE-8XV cables offer RF choking to reduce RFI and improve current balance on antennas. These flexible assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are terminated with high quality silver plated PTFE dielectric PL-259 (UHF male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. The end of these cable assemblies with the ferrite bead choke should be connected to a grounded protector or to the radio, especially when used on End Fed Half-Wave or non-resonant antennas and random wires, and some verticals. They are also used at feed point of a dipole or Yagi antenna. Many installations can benefit from the use of an RF Choke Coaxial Cable Assembly, such as isolating the coaxial cable from a remotely tuned antenna system for improved performance. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. Color of delivered cable can vary. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8XV is the part number for this coaxial cable sold by the foot, and it is available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 3 )

$113.99

—

$154.99

DX Engineering RG-8X PL-259 Low-Loss 50-ohm RF Choke Coaxial Cable Assemblies

DX Engineering RG-8X PL-259 Low-Loss 50-ohm RF Choke Coaxial Cable Assemblies feature our patented* revolutionary PL-259 connector and our premium flexible DXE-8X coaxial cable. They were designed to make the best RG-8X cable assemblies available for HF applications. Adding fifteen Mix-31 ferrite beads makes them even better! The ferrite beads provide RF choking to reduce RFI and improve current balance on antennas. These assemblies are made with low-loss, gas injected foam dielectric DXE-8X cable, featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket. Okay for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, the gas-injected foam of DXE-8X cannot gather moisture and has lower loss than old RG-8X foam cables. The ferrite bead choke part of these cable assemblies should be connected to a grounded protector or the radio end of the cable, especially when used on End Fed Half-Wave or non-resonant antennas, random wires, and verticals. They are also used at feed point of a dipole or Yagi antenna. Many installations can benefit from the use of an RF Choke Coaxial Cable Assembly, such as isolating the coaxial cable from a remotely tuned antenna system for improved performance. DX Engineering RG-8X PL-259 Low-Loss RF Choke Coaxial Cable Assemblies are terminated with our custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. The patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849

Not Yet Reviewed

$101.99

—

$129.99

DX Engineering Ferrite

DX Engineering Ferrites are partially magnetic metal and ceramic mixes available in a variety of forms, including toroid core, bead type and plastic-covered split-bead ferrite called snap-beads. They are used in a myriad of RF suppression applications to mitigate RFI (radio frequency interference) as well as to reduce pulse and other types of RF noise interference. Special ferrites are used for experimentation and electronic circuit building and for making transformers, RF chokes and antenna baluns. The variations of magnetic and non-magnetic metals and non-metal ceramics used to make ferrites are called "Mixes" and each has different radio frequency properties or ranges. Therefore, different mix number ferrites are typically used for different applications within those ranges, determined by decades of experiments by engineers and applications by hams. Each Mix has been assigned a color code to help identify the ferrite, so numerical labeling is not used on the metal. Color coded ferrite can be identified long after the numbered package is discarded or has disintegrated with time. How do they work? Simply use snap-on beads on a cable or wire. An even more effective choke takes a few to several turns of a wire or cable through and around a ferrite snap-on bead or toroid core. This mitigates RFI to, or from, the connected RF noise producing or noise affected electronic device. The results can be very surprising. Solving noise and RFI can be frustrating. Due to the nature of RF and noise interference suppression; the techniques of appropriate use of ferrites can take a bit of trial and error, but are often the best solution for a difficult problem. Use DX Engineering Ferrite for an incredible range of electronic circuits, noise abatement and RF suppression projects. The details of DX Engineering Ferrite mixes and types appear in each product description. Sizes and applications are discussed in "More Details" and in the literature available at the "Documentation" tab of each of these products.

4.88 out of 5 stars ( 198 )

$106.99

—

$116.99

DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies

What if two RF devices – the radio, switch, meter, lightning protector, choke, balun or the antenna – have opposite female connectors, one type-N and the other SO-239? This dilemma is solved with the uniquely helpful DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies, the perfect alternative to questionable straight adapters. Made for any job (HF, VHF and UHF) and especially for outdoors, one top-quality silver plated Type-N male connector and one patented* Next Generation PL-259 (UHF male) connector terminates our premium, low-loss 400MAX coaxial cable to create these very useful Adapter Cable Assemblies. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications, including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX NX Series low-loss assemblies are perfectly suited for short or long cable runs and low or high-power level operations. Our 400MAX coaxial cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95-percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. Note: DXE-400MAX is not recommended for use in repeater applications, VHF/UHF duplex, or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 NX Series Coaxial Adapter Cable Assemblies are terminated at one end with the N-Type male connector and the other end with our custom-designed DX Engineering PL-259 (UHF male) connector. Both silver plated connectors feature machine-crimped shields with 360 degrees of complete mechanical and electrical contact for maximum reliability. PL-259 center pins are hand-soldered, and Type-N center pins are machine-crimped by trained assembly techs to assure a proper connection. Next Generation PL-259 connectors feature: * Full diameter, full-length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double-knurled threaded shells for secure finger tightening These high-quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies are available in selected lengths and at any length in the Custom Cable Builder, only from DX Engineering! *U.S. Patent D745849

5.0 out of 5 stars ( 8 )

$125.99

—

$248.90

DX Engineering MBVE-5UG Auto-Tune Vertical Antenna Upgrade Kits

With DX Engineering MBVE-5UG Auto-Tune Vertical Antenna Upgrade Kits, improve your DX Engineering MBVE-5 or MBVE-5A Vertical Antenna to an Auto-Tune model. You will enjoy an improvement in performance on your vertical antenna with the added convenience and efficiency of remote automatic tuning operation from 80 through 10 meters. Many Upgrade Kits include the automatic tuner, while some Upgrade Kits have all of the same parts, but without the tuner for those who already own the tuner. Your upgrade adds DX Engineering's exclusive new automatic antenna tuner mounting brackets that secure the tuner above the tilt base, well above the ground, for easy installation and access, away from potential damage by water and animals. Click on the DOCUMENTATION tab within any of the antenna packages listed below and then on the CHARTS and GUIDES link to see all of the MBVE-5UG Auto-Tune Vertical Antenna Upgrade Kit offerings. Some of these antenna packages include the tuner and some include tuner mounting brackets and hardware only, for those who already own that tuner. All antenna upgrade packages include the antenna tuner mount, antenna element tubing extension and stainless steel hardware and clamps. As you know, using our ground-mounted vertical, you work DX as you never could with a low, horizontal dipole antenna! Upgrading to as MBVE-5AE Series Auto-Tune Vertical Antenna can improve efficiency and extend your HF operations to new parts of the world. Like any HF vertical, Upgrading your MBVE-5 or MBVE-5A to a MBVE-5AE vertical does require a good ground radial system. We highly recommend installing 32 radials, 65 feet long are recommended. Fewer or shorter radials will work, but with some diminished results. A great ground-mounted vertical has the available space covered with 20 or more evenly spaced radials, each of any length from 15 to 65 feet. Do the work and you'll work the world! ™ DX Engineering MBVE-5UG Auto-Tune Vertical Antenna Upgrade Kits feature stainless steel brackets and hardware and automatic antenna tuners that allow you to access almost all HF bands with only one antenna solution. Order and upgrade your MBVE-5 series Vertical with one of these premium-quality Upgrade Kits from DX Engineering.

5.0 out of 5 stars ( 1 )

$211.97

—

$243.97

DX Engineering MBVE-1UG Auto-Tune Vertical Antenna Upgrade Kits

With DX Engineering MBVE-1UG Auto-Tune Vertical Antenna Upgrade Kits, you may improve your DX Engineering MBVE-1 Vertical Antenna to an Auto-Tune model. You will enjoy an improvement in performance on your vertical antenna with the added convenience and efficiency of remote automatic tuning operation from 80 through 10 meters. Many Upgrade Kits include the automatic tuner, while some Upgrade Kits have all of the same parts, but without the tuner for those who already own the tuner. Your upgrade adds DX Engineering's exclusive new automatic antenna tuner mounting brackets that secure the tuner above the tilt base, well above the ground, for easy installation and access, away from potential damage by water and animals. Click on the DOCUMENTATION tab within any of the upgrade kits listed below and then on the CHARTS and GUIDES link to see all of the MBVE-1UG Auto-Tune Vertical Antenna Upgrade Kit offerings. Some of these antenna packages include the tuner and some include tuner mounting brackets and hardware only, for those who already own that tuner. All antenna upgrade packages include the antenna tuner mount, antenna element tubing extension and stainless steel hardware and clamps. As you know, using our ground-mounted vertical, you work DX as you never could with a low, horizontal dipole antenna! Upgrading to as MBVE-1 Series Auto-Tune Vertical Antenna can improve efficiency and extend your HF operations to new parts of the world. Like any HF vertical, upgrading your MBVE-1 vertical does require a good ground radial system. We highly recommend installing 32 radials, 65 ft. long are recommended. Fewer or shorter radials will work, but with some diminished results. A great ground-mounted vertical has the available space covered with 20 or more evenly spaced radials, each of any length from 15 to 65 ft. Do the work and you'll work the world! ™ DX Engineering MBVE-1UG Auto-Tune Vertical Antenna Upgrade Kits feature stainless steel brackets and hardware and automatic antenna tuners that allow you to access almost all HF bands with only one antenna solution. Upgrade your MBVE-1 series Vertical with one of these premium-quality Upgrade Kits from DX Engineering.

Not Yet Reviewed

$172.98

—

$204.98

  • 1
  • Page 1 of 1