Availability
Hi-Z® Antennas Manual Directional Control Consoles
Hi-Z® Antennas Manual Directional Control Consoles are specialized "low-side" BCD grounding switches that are specifically designed to operate Hi-Z Antennas Phasing Combiner relay units, also known as Phase Controllers. Each HIZ-MDC console controls the phasing and direction selection of only Hi-Z Antennas Receive Vertical Antenna Arrays and supplies power to the array element amplifiers. Hi-Z Antennas Manual Directional Control Consoles are attractive and convenient, featuring a large rotary switch knob and green LEDs arranged as receive array directional azimuth indicators with corresponding compass bearing degree markings on the front panel. Selection of a specific model Manual Directional Control Console (MDC) is required, corresponding to each version of Hi-Z Antennas Receive Array Phasing Combiner or legacy Phase Controller. Each console serves as a replacement for legacy, discontinued Hi-Z manual Shack Switches, and for the discontinued Hi-Z SS-2 and SS-2PLUS: • HIZ-MDC-4 works only with the multiband Four Square Arrays PC-4A and PC-4ELEMENT • HIZ-MDC-8PRO works only with the 85/113 ft. diameter multiband 8 Circle Arrays PC-8PRO and PC4-8PROUP/PLUS • HIZ-MDC-8 works only with the 200 ft./100 ft. diameter monoband 8 Circle Arrays PC-8, PC-8A and PC-8B HIZ-MDC series Manual Directional Control Consoles are stylish, rugged, and heavy — they stay in place on the desk or shelf with four large non-skid rubber feet under a Stainless Steel chassis and an appropriate black powder coated steel cover. The required multi-conductor array power and BCD control cable (purchased separately for the required number of conductors and length to the array) passes through a grommet on the rear panel and connected internally. A rear panel 2.1mm +13.8VDC power connector accepts the included mating 2.1mm plug and unterminated DC power cable, for connection to a user provided +13.8VDC 1A fused, well-filtered power supply.
Not Yet Reviewed
$159.99
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 4 )
$249.99
DX Engineering AVA-3 Active Matching Units
DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.
( 6 )
$139.99
DX Engineering Receive Feedline Voltage Couplers
DX Engineering FVC-1 Feedline Voltage Couplers provide an interface between control switches and voltage-controlled antenna systems. These specialized controllable bias-tee devices place 0V DC, +12V DC, -12V DC, and 12V AC output voltages onto the receive antenna feedline via the 75 ohm F connector or onto a 2-conductor control line. These FVC-1 couplers function from below 500 kHz to 30 MHz and provide four selections for switching antenna array directions or changing from one array to another. These couplers were designed for use with; the DX Engineering receive-only four-square antenna systems, reversible Beverage antenna systems, and remote switches. DX Engineering switch control consoles may be connected directly to the BCD switch control input of FVC-1 couplers. Alternatively, you may use your own 12V DC voltage switching system or 1 of 4 grounding switches to control the coupler by resetting internal jumpers. The connection of the feedline voltage couplers to any radio receive antenna input is to be made using either the standard RCA phono or the F connector. This allows for the use of readily available RF-compatible RCA phono patch cords or a 75 ohm coaxial cable and connectors, which protects your receive system from an accidental connection to transmitting equipment. FVC-1 feedline voltage couplers have two LED indicators--red and green--which indicate the presence and polarity of the output control voltage selected. The LEDs may function as directional indicators that can be read at a convenient distance or they can aid in troubleshooting. Each of our DX Engineering FVC-1 Feedline Voltage Couplers comes with a heavy duty 120V AC wall transformer, which provides a safe 12V AC to operate your receive antenna system. Here are other exclusive features of FVC-1 voltage couplers: * Metal housing--superior shielding, rugged, and easy mounting * Convenient installation--mount anywhere in your shack * Rugged control connector - a reliable, solderless, and removable connector with screw conductor clamps * Internal thermal reset fuse offers full protection against accidental shorts Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Got antenna switching voltages? DX Engineering FVC-1 Feedline Voltage Couplers will solve many switching needs easily and economically!
( 1 )
$185.99
DX Engineering 2-Port Splitter-Combiners
DX Engineering 2-Port Splitter-Combiners are receive signal-level RF devices that operate from 300 kHz to 30 MHz, available in 50 ohm and 75 ohm versions. They're typically used to split one RF signal to properly feed two receivers, or the receive antenna inputs of one transceiver and one separate receiver. They also properly combine two receiving antennas in phase, such as Beverage antennas, to form a phased receive array. Important features of the DX Engineering 2-Port Splitter-Combiner: * Available for 50 ohm and 75 ohm systems * Broad, 300 kHz through 30 MHz operating range * High-quality components * Isolated ports * Metal housing for superior shielding and longer life * Reliable side-mount connectors: BNC female for 50 ohm, F female connectors for 75 ohm model * Economical solution to potential impedance errors that cause losses With the updated "SC" versions of the original 2-Port Splitter-Combiner, DX Engineering has maintained the port isolation design that prevents signal performance degradation caused by impedance errors in less-than-perfect receive systems. The normal signal level reduction when used as a splitter is just over 3 dB per port. As with any system, losses are dependent upon source and load impedances being matched. DX Engineering Splitter-Combiners provide equal power, voltage, and current to matched loads on ports 1 and 2. The primary advantage is that individual receiver input variations, or a band filter attached to only one port, will not seriously affect the signal level in the other receiver. In addition, any spurious signals generated in one receiver are greatly attenuated by the 2-Port Splitter-Combiner before reaching the second receiver. When splitting in-phase signals, the loss is somewhat less. Any unused port of the 2-Port Splitter-Combiner should be terminated and specified losses are based on source and load impedances being matched. The DX Engineering 2-Port Splitter-Combiner is a passive device; therefore it requires no power to operate. Use the 75-ohm version for combining two 75 ohm antenna feedlines into a single 75 ohm feedline with negligible loss; or use the 50-ohm version for 50-ohm antennas and feedlines. Examples for applications are for two antennas forming an in-phase (broadside) receiving array, a cross-fire Echelon Beverage array, or any type of array with fixed phasing. There are a number of advantages to using these units for combining antenna systems over a standard parallel connection: * Splitter-Combiners match the entire antenna system to the feedline impedance; conversely, paralleling feedlines by using a T-connector divides the impedance in half, causing mismatched losses * With antennas connected directly in parallel, if either one develops a high impedance open, becomes shorted, falls down, or has a feedline problem, the entire antenna system may become unusable. By using the 2-Port Splitter-Combiner, only the problem antenna is unusable; the antenna on the other port can still be used * Unlike quarter wave matching sections that only work on one band, these Splitter-Combiners have extremely wide bandwidth * Due to the built-in isolation and balancing, these units limit the signal loss to approximately 3 dB per port * 2-Port Splitter-Combiners provide very high isolation between ports 1 and 2; this prevents either antenna from interfering with the other during normal operation Note: These devices cannot be used for FM broadcast, VHF, UHF, CATV or Satellite TV. They operate only MF through HF. Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 5 )
$100.99
—
$107.99
DX Engineering Phased Array Quarter Wave Tuned Cables
DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.
( 3 )
$137.13
—
$245.99
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.
Not Yet Reviewed
$249.99
DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable
DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable is our regular RG-6U with a Type II PVC jacket, low loss and greater protection against electromagnetic interference. Available cut to length or in 1,000 ft. spools; this is a high-quality standard RG-6U quad-shield cable. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. (Please Note: Also available is our waterproof direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ-CTL and DXE-RG6UFQ-1000.) DXE-RG-6UQ cable is ideal for many applications, such as active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution as well as satellite radio installations like Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up to the microwave frequencies that Satellite Radio systems employ! Our RG-6 quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding and the UV protected black jacket is made with a tough, but very flexible, PVC. The nominal impedance of DXE-RG-6UQ cable is 75 ohms, and it has a nominal Velocity Factor of 82%. The minimum bend radius of this cable is 2.50 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? Please Note: Also available is our direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ and DXE-RG6UFQ-1000. This DX Engineering RG-6UQ 75-ohm Standard Quad-Shield Coaxial Cable is a Type-II PVC jacket RG-6 quad-shield cable that is RoHS compliant. Check out these low attenuation figures: 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? Order DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable.
( 1 )
$219.99
DX Engineering CC-4 Four Position Control Consoles
The DXE-CC-4 Four Position Control Console is used for remote switching of relay control devices requiring 1 of 3 positive voltage control lines with a ground return. This control console is directly compatible with: SSB Electronic Four-Port Mast-Mount Antenna Switches: AS-304 N (ESB-5050) AS-304 UHF (ESB-5053) WIMO Remote Polarization Switches: WMO-18080 WMO-18081 WMO-18082 WMO-18083 Unified Microsystems Receive Antenna Switch: UMS-RAS-4 (The DXE-CC-4 is an essential component for manual control of the UMS BevFlex-4X-Q Four-Direction Reversible Beverage Antenna System.) The DXE-CC-4 can be used in other applications using this control scheme: Control SWITCH Control Console Output Terminal 1 Terminal 2 Terminal 3 Position 1 - LED1 - ON 0 0 0 Position 2 - LED2 - ON +13.8 VDC 0 0 Position 3 - LED3 - ON 0 +13.8 VDC 0 Position 4 - LED4 - ON 0 0 +13.8 VDC The DXE-CC-4 Four Position Control Console features: • Large Rotary Knob • Stainless Steel Housing • Non-Skid feet • On-Off toggle switch • Four green LEDs indicate position chosen • Erasable position label fields • Filter capacitors on each line • Internal automatic resettable fuse • Includes a 2.1 mm power plug for +13.8 VDC power connection
( 1 )
$161.99
DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes
Introducing DX Engineering "Maxi-Core® 20" Baluns and Feedline Chokes. They reduce or eliminate currents on the outside of your feedline allowing you to hear and to be heard much better. They keep more RFI/BCI out of your antenna and receiver and transfer more of your transmitted signal to the antenna for higher efficiency, the best antenna pattern and maximum performance. Signaling a new era of RF performance across the 1.8 to 54 MHz frequency range, DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes handle full-legal-power-plus and provide higher common mode impedance (CMI) across a greater frequency range than competing models and even previous DX Engineering and Comtek models. Years of R&D coupled with major advancements in test equipment and techniques combined with custom ferrite materials have allowed our engineering team to design the DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes. Maxi-Core® 20 Baluns and Chokes have high CMI across the AM Broadcast band and the HF/6M spectrum, which is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. Hear and be heard with DXE Maxi-Core® 20 Baluns and Feedline Chokes. Choose superior performance from these models: * DXE-MC20-1-1 Maxi-Core® 20 - 1:1 Current Choke Balun - For all HF-6m balanced antennas with a 50 ohm feedpoint, including resonant dipoles, loops, Yagis, beams, etc. * DXE-MC20-FC Maxi-Core® 20 - 1:1 Feedline Choke – This high CMI line isolator is perfect for use in line on 50 ohm coaxial feedlines, at the antenna, tower or shack end of the feedline. * DXE-MC20-1-1T Maxi-Core® 20 - 1:1 Current Choke Balun – This 1:1 "T" model is for force feeding antennas with a tuner. Use it at the end of ladder line of any impedance or mounted on a coax fed non-resonant antenna. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-C4-1 Maxi-Core® 20 - 4:1 Current Choke Balun is for use on antennas with a 200 ohm feedpoint and at the end of any impedance ladder line, especially on antenna systems with higher impedance. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-V4-1 Maxi-Core® 20 - 4:1 Voltage Balun is a 200 ohm to 50 ohm transformer for use on random long-wire and OCF antenna applications. This true voltage balun is intentionally designed with low CMI for antennas that need a transformer without RF choking for easier antenna tuner operation and it tolerates elevated SWR. Maxi-Core® 20 Baluns and Feedline Chokes are built into a convenient weather resistant NEMA enclosure that is mounted easily with optional brackets. They feature 1/4-20 stainless steel hardware and a high quality silver-plated PTFE dielectric SO-239 (UHF female) input connector. The SO-239 connector limits power handling to 5 kW at low SWR and reduced power at elevated SWR. These baluns and the feedline choke exhibit very low insertion loss and inherently low SWR. Optional mounting brackets are available for use on wire antennas or for verticals, Yagi and beam antennas. See the Suggested Parts tab after clicking "More Detail" on the model of interest. Combination packages that include balun or choke and mounting bracket are also available.
( 143 )
$147.99
—
$169.99