Selected Filters


Availability


8 Results Found For "75 ohm coax"

Part Groups

Results 1 - 8 of 8

DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable

DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable is our top-of-the-line, direct-bury RG-6. It has low RF signal loss and provides greater protection against electromagnetic interference. Available cut-to-length by-the-foot or in 1,000 ft. spools, this is the best ultra-high quality RG-6/U self-healing quad-shield cable solution. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. DXE-RG-6UFQ cable is ideal for many receiving applications including active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution and satellite radio installations such as Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up through microwave frequencies of satellite radio systems! Our RG-6 flooded quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding. The waterproof UV protected black jacket is made with a tough and flexible polyethylene (PE). This cable is infused with a flooding compound that provides a permanent barrier to moisture and is self-healing to minor cuts. The nominal impedance of DXE-RG-6UFQ cable is 75 ohms with a nominal Velocity Factor of 82% (VF = 0.82). The minimum bend radius is 2.500 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? DX Engineering RG-6U 75-ohm Flooded Quad-Shield Coaxial Cable is absolutely the best RG-6 quad-shield cable available and it is RoHS compliant! Check these super low attenuation figures! 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? If so, then order the new benchmark in RG-6 cable: DX Engineering RG-6U 75-ohm Flooded Quad Shield Coax. Your efforts will be rewarded with the results that you expect, using the best cable from DX Engineering.

4.78 out of 5 stars ( 9 )

$255.99

DX Engineering Pretuned Quarter-Wave Phased Array Cables

DX Engineering Pretuned Quarter-Wave Phased Array Cables are ready to go into your phased array for 80 or 40 meters. These RG-11U coaxial cable assemblies are electronically tuned during production to 3650 kHz and 7100 kHz, the two most popular phased array frequencies. Pretuned Quarter-Wave Phased Array Cables ensure optimum pattern control and gain from your phased antenna array. They are available individually, in pairs and in four-packs, all terminated with soldered silver-plated PL-259s. These cable assemblies are exactly as required for many 80 and 40 meters phased arrays including Comtek Hybrid Four Square Arrays, DX Engineering TFS4 Four Square Arrays, as well as DX Engineering Dual Vertical Arrays. DX Engineering Pretuned Quarter-Wave Phased Array Cables are made from the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable. They are called "phasing feed-lines" because they are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. This RG-11U coaxial cable is manufactured to DX Engineering specifications, with a nominal velocity factor of 0.82. That means they're the right physical length to allow for easy burial and routing from the center-mounted array phasing unit to the base of each vertical element. Maximum performance is achieve with properly installed phased arrays, including ground-mounted base-fed full-size quarter-wave elements with free-space array dimensions and complete, interconnected ground radial wire systems. The electrical dimensions of phased array transmission cables are critical to system performance. Each of our cable assemblies is hand crafted and electronically tuned at DX Engineering. Eliminate the trouble and concern of trying to tune your own cables and order a set of DX Engineering Pretuned Quarter-Wave Phased Array Cables. NOTE: Custom tuned phased cables for all other frequencies in each Amateur band are also available. See DX Engineering Phased Array Quarter Wave Tuned Cables.

5.0 out of 5 stars ( 1 )

$319.96

—

$479.96

DX Engineering Phased Array Quarter Wave Tuned Cables

DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.

4.67 out of 5 stars ( 3 )

$275.99

—

$499.99

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.

Not Yet Reviewed

$379.99

—

$499.98

DX Engineering Reversible Beverage Systems

DX Engineering Reversible Beverage Systems basically allow two Beverage antennas to be switched to receive in opposite directions while sharing the same physical space. DXE-RBSA-1P Reversible Beverage Systems antennas provide two opposite "end-fire" directional patterns with excellent front-to-rear directivity and superior signal-to-noise ratio as compared to transmitting antennas. Dramatically improved long distance weak signal results may be achieved on MW and the 160, 80 and 40 meter bands, including shortwave bands, with receive-only Beverage antennas using wires that are typically only 350 to 800 feet long, depending upon the band of interest. The two-direction DXE-RBSA-1P Reversible Beverage Systems offer a space and installation advantage because two opposite single-wire Beverage antennas would require twice the length. DX Engineering Reversible Beverage Systems are immune to the strong signal overload and core saturation common in multi-transmitter contesting environments and are used by winning contest stations and low-band DXers around the world. These Reversible Beverage antennas have two "F" connectors; one "Away" port for the default end-fire receiving pattern off the end of the wire, and one "Toward" port for the opposite direction. The standard configuration of these systems has the "Toward" port terminated (75-ohm termination included), so both antennas share a common feedline. Applying a negative 10 to 18V DC to the feedline switches the system between the two antenna ports for reception in opposite directions. For simultaneous reception from opposing directions, each of the two feedlines can be run to separate receivers, with the termination load not used. You can build a 4-direction receive antenna system with two DXE-RBSA-1P Reversible Beverage Systems and one DX Engineering RLS-2 Two-Port Receiving Switch that also requires only one feedline! The optional DX Engineering Feedline Voltage Coupler, model DXE-FVC-1 is highly recommended to provide all of the required feedline voltage injection. Plus, the optional DXE-EC-4 BCD Control Console completes the system for four-direction switching right in the shack. DX Engineering Reversible Beverage Systems are optimized to use our optional 450 ohm ladder line for the antenna element. We strongly recommend using that type of "window line" because the consistent spacing of the antenna wires will produce the best operational results. However, the RBS will work with any 300-600 ohm 2-wire line. For best feed line results, DX Engineering highly recommends using our high quality flooded or quad-shielded 75-ohm coax with F-type compression connectors to ensure a weatherproof installation. Additional features include: * Broad operating range, 0.2 to 30 MHz * Fully isolated grounds prevent common-made noise and unwanted signals * 75 ohm design enables the use of high quality, low cost cable and connectors * RF shielded housing used for isolation and improved life * Directional Switching Voltage: nominal 12V AC or negative 12V DC, feedline injected * Directional Switching Current: less than 80 mA * Antenna impedance: 300-600 ohm (450 ohm recommended) * Feedline impedance: 50-75 ohm (75 ohm recommended) * RBSA-1FP Feed Point unit dimensions: 5.5 in. width x 3.5 in. depth x 1.5 in. height * RBS-1RT Reflection Transformer unit dimensions: 2.125 in. width x 2.125 in. depth x 1.125 in. height Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Reversible Beverage Systems offer the best DX reception and flexibility in high performance two-direction wire Beverage receive antennas. Get yours set up soon!

5.0 out of 5 stars ( 3 )

$335.98

DX Engineering RTR-2 Modular Receive-Transmit Interfaces

DX Engineering RTR-2 Modular Receive-Transmit Interfaces provide the easiest and safest method for connecting a dedicated receive antenna to an HF transceiver that does not have a separate receive antenna input. Placed inline with the transceiver's antenna connector, the RTR-2 does the job of a 200 watt T/R relay using the amplifier keying line for failsafe protection, so your transmitted energy cannot go to the receive antenna. Three internal Plug-in Module option slots provide added features and protection: * DXE-RPA-2-PM Receive Preamplifier Plug-in Module * DXE-TRI-PM Transmit Receive Interrupter Plug-In Module * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-in Module DX Engineering RTR-2 Modular Receive-Transmit Interfaces allow the standard transceiver owner to enjoy the advantages of separate receive antennas. For the unswitched receive antenna (RX ANT) port on expensive transceivers, the RTR-2 interface also adds inexpensive failsafe protection. The receive antenna line can be opened or grounded with the optional DXE-TRI-PM Interrupter plug-in module. The RTR-2 is a very useful device for many applications, including: * Connection of external receiving antennas to transceivers lacking external antenna ports * T-R antenna switch for older equipment using separate transmitters and receivers * Interfacing antennas to older phasing or noise cancelling systems * Addition of a switchable receive preamplifier to any transceiver or transmitter and receiver combination * Excellent failsafe receiver protection for close-spaced transmit and receive antennas, without performance degradation of diode circuits of other devices. RTR-2 units feature a unique, failsafe connection method that prevents the hot switching and timing errors that are common on other transmit/receive relays. RTR-2 interfaces switch fast enough for partial break-in CW operation. There are many simple applications for the new RTR-2 and now internal modules can add dramatically improved reception of those really weak signals on the crowded HF bands! DX Engineering RTR-2 Modular Receive-Transmit Interfaces enable operators to enjoy improved reception with any low noise receiving antenna system. This shielded enclosure relay system provides a safe method of connecting a receive antenna, such as a Beverage, Active Receive system, or other receiving accessories to your radio. Major features that make the DX Engineering RTR-2 Receive Antenna Interfaces your best choice for a receive T/R system device: * New Status Indicating Color-changing LEDs * Three internal slots for new DX Engineering modules * New Key Line Out connector for Amplifier * New internal jumper for placing DC on the Receive Antenna feedline for Active or Loop receive antennas * Attractive and heavy stainless steel enclosure * 200 watts RF switching capability * Supports CW partial break-in * Main transmit antenna connector is SO-239 (UHF female) * Radio RF connector is SO-239 (UHF female) * Receive antenna input is 75 ohm F connector * Receive outputs are standard 75 ohm Type F connectors * Inputs are 50 ohm BNC or 75 ohm F (Optional transformer module available) * Safe switching--transmit antenna is always connected to transceiver on power-off * Hot switching lockout--disables receive antenna during transmit mode (Optional DXE-TRI-PM can be set to short the RX ANT line) * Versatile--allows inclusion of Optional RF preamplifiers and other plug-in modules * Simple 13.8 Vdc input for all operations An indispensable accessory for the DX enthusiast and useful for any Amateur's shack, DX Engineering RTR-2 Modular Receive-Transmit Interfaces can help you expand and improve your station's antenna connections and the protection of your equipment.

4.92 out of 5 stars ( 12 )

$375.99

DX Engineering RPA-2 Modular Receive Preamplifiers

DX Engineering RPA-2 Modular Receive Preamplifiers are newly designed versions of the RPA-1 with internal slots for accessory modules. They accommodate the addition of the one optional plug-in module, such as the 75 to 50 ohm Impedance Transformer Module, or the Receiver Guard 5000HD Plug-In Module, or the DX Engineering Clifton Laboratories Z10020 AM Band Filter Module. DXE-RPA-2 preamps have very low internal noise and are optimized for the 300 kHz to 35 MHz range. They help you hear the weakest signals without artificially raising the noise. Meticulous craftsmanship and durable, robust components allow these preamplifiers to withstand high signal levels while providing superior dynamic range and third-order intercept performance that equals or exceeds most receiver and transceiver front-ends. RPA-2 Receive Preamplifiers have key features added, as requested by our tech-oriented customers and enthusiasts: - Internal slot accommodates the optional 75 to 50 ohm Impedance Transformer Module to accomplish typical receive antenna feedline to equipment transitions without losses -Also allows direct connection to 50 ohm receive antenna feedline BNC connectors with no transformer required - Internal slot for DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module – Front-end protection for the RPA-2 - Secure BNC female connectors and receive-system friendly F female connectors remain; both prevent accidental connection to transmitting devices with UHF connectors - A green LED indicates when DC power is present and the preamplifier circuit is engaged. - An ingenious positive-capture threaded-sleeve 2.1 mm power connector that ensures the DC power cannot be accidentally disconnected from the RPA-2. - Alternatively, a simple internal jumper change allows the RPA-2 to be powered by DC on the feedline While many other common preamplifiers suffer from harmonic distortion, RPA-2 Modular Receive Preamplifiers include our exclusive, advanced push-pull design that eliminates harmonic distortion. Their high quiescent current increases their ability to handle strong signals without distortion or overload. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 Vdc input. Please do not use a cheap wall transformer or noisy switching wall-wart to power these top-of-the-line preamplifiers. Indoor installation at the back of the radio is recommended for RPA-2. For those who want to place them in an enclosure at a receive antenna system, a handy internal jumper allows these new units to be powered on the coaxial cable. RPA-2 Receive Preamplifier Specifications: -Input and Output Connectors, female: BNC and F -Frequency Range: 300 kHz to 35 MHz -Gain: 16 dB, +/- 1.5 dB (over entire frequency range) -Output Third Order Intercept: 43 dBm -Noise Figure: 3.5 dB -One dB Compression Point: +26 dBm (400 mW output) -Dynamic Range, IM3: 110 dB or greater (500 Hz bandwidth) -Power Requirement: 12-18 Vdc, 140 mA max. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering RPA-2 Modular Receive Preamplifiers offer superior receiving results on crowded medium wave and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the advanced operational performance of DX Engineering Receive Preamplifiers. You will be able to pull in the weakest signals and snag that rare one, under the most difficult conditions, when you need it the most. Order your DX Engineering RPA-2 today!

4.36 out of 5 stars ( 14 )

$269.99

DX Engineering Receive Short Element Active Vertical Antennas

DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.

4.75 out of 5 stars ( 4 )

$349.98

—

$499.98

  • 1
  • Page 1 of 1