Availability
DX Engineering Receive 8 Circle Array Controllers
DX Engineering RCA8C-1 Receive 8 Circle Array Controllers are the highly sophisticated switch controller relay units from the Eight Circle Array Systems--the receiving systems that use time delay phasing--rather than the conventional narrow-band, frequency-dependent phasing, to provide eight 45 degree spaced directional patterns. The RCA8C time delay phasing is directivity-optimized to produce wider and deeper rear nulls and a narrower main lobe. The result is that noise and undesirable signals are greatly reduced for a superior front-to-rear ratio (F/R). Better control of phase and currents provides a cleaner pattern with the Receive 8 Circle than is available with vertical antenna transmit arrays. DX Engineering Receive 8 Circle Array Controllers are designed to be used with eight identical vertical active or passive vertical elements, symmetrically spaced in a large circle, to provide switching for an 8-direction receiving antenna system. Passive elements will generally provide you with a monoband receiving system. Finally, these systems offer greater reliability in receiving applications. Receive Eight Circle Array Controllers use sealed relays sized for receiving applications with silver contacts to prevent oxidation and contamination. Most transmitting four-square switches use large open-frame relays where the contacts are exposed to the air, which can lead to contamination. Relays with brass contacts can oxidize, leading to poor conductivity. Receive Eight Circle Array controllers feature: * W8JI design * Operation from 100 kHz to 30 MHz * Excellent directivity for better signal-to noise ratio * Switching console provides eight 45 degree spaced directions * Less physical space and maintenance required than phased Beverage antennas * Low current DC powered control console allows system operation without AC power mains The optional DX Engineering Eight Circle Receive Short Element Active Vertical Antenna Package, DXE-RSEAV-8, offers excellent receiving performance from 100 kHz to 30 MHz, while using only a 8.5 ft. (2.6m) aluminum vertical antenna elements. A unique design makes the Receive Eight Circle Array System vastly superior to traditional active vertical antennas in both strong signal handling and feedline decoupling. This results in significantly better weak signal reception due to lower spurious signal interference and reduced noise. DX Engineering RCA8C Receive 8 Circle Array Controllers are the foundation of your Eight Circle Array!
Not Yet Reviewed
$499.99
DX Engineering Receive Four Square Array Controllers
The patented DXE-RFS-3 DX Engineering Receive Four Square Array Controllers are the heart of a sophisticated receiving system that uses time delay phasing rather than the conventional narrow-band, frequency-dependent phasing systems. The time delay phasing is directivity-optimized to produce wider and deeper rear nulls and a narrower main lobe. The result is that noise and undesirable signals are greatly reduced for a superior front-to-rear ratio (F/R). Better control of phase and currents provides a cleaner pattern than those found on available transmit four square arrays. The RFS-3 DX Engineering Receive Four-Square Array Controllers are the switch relay units that are optimized to use the DX Engineering's Active Vertical Antenna Package DXE-ARAV4-4P of four active verticals. These products together offer great F/R response over octaves of bandwidth. DX Engineering's Active Receive Antenna System offers excellent receiving performance from 100 kHz to 30 MHz, while using only a 8.5 ft. antenna element. A unique design makes it vastly superior to traditional active antennas in both strong signal handling and feedline decoupling. This results in significantly better weak signal reception due to lower spurious signal interference and reduced noise. Finally, these systems offer greater reliability in receiving applications. The RFS-3s use sealed relays sized for receiving applications with silver contacts to prevent oxidation and contamination. Most transmitting four-square switches use large, open-frame relays where the contacts are exposed to air, which can lead to contamination. Relays with brass contacts can oxidize, leading to poor conductivity. Advantages of the RFS-3 Receive Four-Square Antenna Systems over other small or medium-size receiving arrays include: * Reduced susceptibility to high angle signals compared to EWE, Flag, Pennant, and K9AY antennas * Excellent directivity in a small space for better signal-to-noise ratio * Switchable in four 90 degree spaced directions * Directivity over a very wide frequency range using DX Engineering DXE-ARAV4-4P active elements * Less physical space required than a Beverage antenna, and active elements need only a minimal ground system * Enhanced relay contact reliability
Not Yet Reviewed
$375.99
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 4 )
$349.98
—
$499.98
DX Engineering Phased Array Quarter Wave Tuned Cables
DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.
( 3 )
$275.99
—
$499.99
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.
Not Yet Reviewed
$379.99
—
$499.98
DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable
DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable is our top-of-the-line, direct-bury RG-6. It has low RF signal loss and provides greater protection against electromagnetic interference. Available cut-to-length by-the-foot or in 1,000 ft. spools, this is the best ultra-high quality RG-6/U self-healing quad-shield cable solution. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. DXE-RG-6UFQ cable is ideal for many receiving applications including active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution and satellite radio installations such as Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up through microwave frequencies of satellite radio systems! Our RG-6 flooded quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding. The waterproof UV protected black jacket is made with a tough and flexible polyethylene (PE). This cable is infused with a flooding compound that provides a permanent barrier to moisture and is self-healing to minor cuts. The nominal impedance of DXE-RG-6UFQ cable is 75 ohms with a nominal Velocity Factor of 82% (VF = 0.82). The minimum bend radius is 2.500 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? DX Engineering RG-6U 75-ohm Flooded Quad-Shield Coaxial Cable is absolutely the best RG-6 quad-shield cable available and it is RoHS compliant! Check these super low attenuation figures! 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? If so, then order the new benchmark in RG-6 cable: DX Engineering RG-6U 75-ohm Flooded Quad Shield Coax. Your efforts will be rewarded with the results that you expect, using the best cable from DX Engineering.
( 9 )
$255.99