Selected Filters


Availability


4 Results Found For "75 ohm coax"

Part Groups

Results 1 - 4 of 4

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.

Not Yet Reviewed

$699.99

DX Engineering Phased Array Quarter Wave Tuned Cables

DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.

4.67 out of 5 stars ( 3 )

$649.99

DX Engineering Reversible Beverage Antenna System Combos

DX Engineering Reversible Beverage Antenna System Combos allow two Beverage antennas to be switched to receive in opposite directions while sharing the same physical space. These exciting new reversible Beverage combos include DX Engineering's superb receive preamp! Dramatically improved weak signal results can be achieved on MW, BCB, 160, 80 and 40 meter bands and shortwave bands with receive-only Beverage wire antennas that are typically 350 to 800 feet long, depending upon the lowest band of interest. DX Engineering Reversible Beverage System Combos are immune to the strong signal overload and core saturation common in multi-transmitter contesting environments. Reversible Beverages have two antenna F connectors; one "Away" port for the default end-fire receiving pattern off the end of the wire, and one "Toward" port for the opposite direction. Applying a negative 10 to 18 V DC to the feedline switches the system between the two antenna ports for reception in opposite directions. You can build a 4-direction receive antenna system with two reversible Beverage systems and one DX Engineering RLS-2 Two-Port Receiving Switch that also requires only one feedline! The optional DX Engineering Feedline Voltage Coupler, model DXE-FVC-1 is highly recommended to provide all of the required feedline voltage injection. Plus, the optional DXE-EC-4 BCD Control Console completes the system for four-direction switching right in the shack. These RBS systems will work with any 300-600 ohm 2-wire line. For best low-loss low-noise results, use DX Engineering flooded or quad-shielded 75-ohm coax; with our F-type compression connectors to ensure a weatherproof installation. DX Engineering RPA-1 Receive Preamplifiers use RCA-type phono jacks and CATV Type-F female connectors for the input and output connections to prevent accidental connection to transmitting devices. RPA-1 Receive Preamplifiers feature a built-in relay that automatically bypasses the preamplifier circuit when DC power is removed. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 V DC input. Details for DX Engineering Reversible Beverage Antenna System Combos: Receive preamp: * Gain: 16 dB, +/- 1.5 dB, from 300 kHz through 35 MHz * Dynamic range (IM3) at 500 Hz BW: 110 dB or greater * Output Third Order Intercept: +43 dBm * Noise figure: 3.5 dB * Compression: 1 dB at +26 dBm (nominally 0.4 W output) * Power requirement: 12-18 V DC at 140 mA maximum * Power Input: 2.1 mm DC coaxial power connector Reversible Beverage transformer features: * Broad operating range, 0.2 to 30 MHz * Fully isolated grounds prevent common-made noise and unwanted signals * 75 ohm design enables the use of high quality, low cost cable and connectors * RF shielded housing used for isolation and improved life * Directional Switching Voltage: nominal 12 V AC or negative 12 V DC, feedline injected * Directional Switching Current: less than 80 mA * Antenna impedance: 300-600 ohm (450 ohm recommended) * Feedline impedance: 50-75 ohm (75 ohm recommended) * RBSA-1FP Feed Point unit dimensions: 5.5 in. width x 3.5 in. depth x 1.5 in. height * RBS-1RT Reflection Transformer unit dimensions: 2.125 in. width x 2.125 in. depth x 1.125 in. height Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Reversible Beverage Antenna System Combos offer package convenience and superior receiving results on today's crowded medium and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the exceptional performance of DX Engineering products. Order one of these DX Engineering Reversible Beverage Antenna System Combos to make the best of your MW/HF reception!

Not Yet Reviewed

$605.97

DX Engineering DVA Dual Vertical Array Systems

DX Engineering DVA Dual Vertical Array Systems are advanced phasing systems that have set a new standard for array performance with two ground-mounted verticals. Dual Vertical Array Systems include a compact DVA Phasing Relay Unit made specifically for an individual HF band and an EC-DVA Directional Control Console. DX Engineering Dual Vertical Arrays produce two opposite enhanced End-Fire Cardioid patterns and one Broadside-Omni pattern. Heavy-duty components handle over 2 kW continuous RF power for enhanced performance at low SWR over a wide bandwidth. The Dual Vertical Array end-fire directional patterns achieve a real front-to-back over 20 dB with typical array forward gain up to 3 dB over a single vertical. The greatest advantage of a Dual Vertical Array is that a tower and rotator are not required, as with a Yagi antenna. Especially for 160, 80, and 40, and even on the other HF bands, a Dual Vertical Array is mechanically simpler and safer. Here is a financially practical directional antenna that is much easier to install! These are great directional antenna systems for temporary and Field Day operation, as well as for permanent builds, because they ARE so much easier to install than a beam! If you are dissatisfied with your present system, are ready for an upgrade, or just need to get out of the tower game, the DX Engineering DVA is your answer! Refurbish an existing antenna system, equip your temporary array, or build a new phased array with a DVA. It's all on the ground, safe and simple: DX Engineering Dual Vertical Arrays offer a better way to enjoy a high-performance mono-band directional antenna. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.

5.0 out of 5 stars ( 4 )

$575.98

—

$685.98

  • 1
  • Page 1 of 1