Availability
12 Results Found For "in-line"
DX Engineering RR8B-HP Remote Antenna Switches
DX Engineering RR8B-HP Remote Antenna Switches are RF switches designed to have excellent performance on HF through 6 meters. Using 16 custom, sealed, moisture-resistant relays, these Remote Switches provide the best port-to-port isolation available with reliable, long-term performance. RR8B-HP switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, thereby allowing their use in complex antenna phasing and stacking systems. DX Engineering RR8B-HP switches use a removable screw-terminal control cable plug that greatly simplifies installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting-bracket flange and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. O.D. Features of the RR8B-HP Remote Antenna Switches include: * Fully RF shielded with stainless steel mounting bracket and hardware * Best port-to-port isolation available: Over 70 dB isolation below 30 MHz, Over 55 dB isolation below 60 MHz * Loss: Less than 0.1 dB below 60 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Shorted or open selection of unused antenna ports * Sealed 20 ampere, RF-rated relays * Safe 12V DC relay operation * Lightning protection on control lines * External quick-connect plug for control lines * Reliable operation in extreme-weather conditions Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For reliable operation of multiple antennas through the operation of remote switching, order DX Engineering RR8B-HP Remote Antenna Switches to do the job!
( 5 )
$549.99
DX Engineering RR8B-SD Remote Antenna Switches
DX Engineering RR8B-SD Remote Antenna Switches are the highest power handling antenna switches in the DX Engineering RR8 Series. Think of them as Super Duty. They are designed to switch up to 8 coaxial lines in high-power RF systems. RR8B-SD switches use enclosed RF-rated relays with exceptional RF voltage and current capability to provide reliable, long-term performance. DX Engineering RR8B-SD switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, allowing for use in complex antenna phasing and stacking systems. RR8B-SD switches use removable screw-terminal control cable plugs that greatly simplify installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting bracket flange, and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. outside diameter. RR8B-SD Remote Antenna Switches feature: * Fully shielded, high impact thermoplastic enclosure, stainless steel mounting bracket, and hardware * Excellent port isolation; greater than 60 dB at 30 MHz, worst case * Power Rating: Greater than 10 kW in normal amateur operation on all modes when using antennas with less than 2:1 SWR on 30 MHz and below. Greater than 5 kW above 30 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Lightning protection on control lines * Shorted or open selection of unused antenna ports * Custom sealed 30 ampere high-voltage RF relays * Solderless removable plug for easy installation of control line with no disassembly * Safe 12V DC relay operation * Reliable operation in all weather extremes Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For multi-band multi-antenna QRO operation, there is no better remote switch than DX Engineering RR8B-SD Remote Antenna Switches!
( 4 )
$599.99
DX Engineering HF Portable TW Antennas and Accessories
Preserving and building upon the legacy of this premier portable HF antenna line, DX Engineering is now the manufacturer and seller of TW Antennas! DX Engineering's acquisition of the products and designs of these unique HF portable and stealthy antennas brings easy access and simplified ordering to this line formerly known as Transworld. DX Engineering HF Portable TW Antennas and Accessories feature complete portable antenna packages and all of the individual components to build a custom stealthy system. Will you use these compact HF antennas as portables, fixed antennas, or both? Choose your own path to stealthy operations and to join in the fun of portable HF! Naturally stealthy, these compact HF vertical-dipole TW antennas feature a black finish that is excellent on fixed antennas in HOAs or where "CC & R" antenna restrictions preclude the installation of towers and easily visible HF antennas. Simply unfold the DXE-TW-BAS-BLK Top and Bottom Sections, add your Band Box Center Post section, and place the antenna on the optional 41 in. long permanent mounting post, DXE-TW-PMP, and operate! Note: Although a permanently-installed mounting pier (DXE-TW-PMP) is available, DX Engineering TW Antenna band boxes are not waterproof. Do not leave your TW Antenna exposed to the elements. For portable use, the lightweight foldable Quadrastand, DXE-TW-AQ, lets you set up your DX Engineering HF Portable TW Antenna wherever you happen to be. Quadrastand's gray fiberglass legs will give decades of rugged, dependable service. And since they're fiberglass, there's no chance of corrosion from contact with earth or sand. Think about equipping for your special operating event plans like Scouts Jamboree On-The-Air (JOTA), Field Day or even SOTA (Summits On-The-Air) for backpacking and general camping with HF! A great Carry Case, DXE-TW-DXBAG, is available to make traveling with these antennas in your car or RV a snap. DX Engineering HF Portable TW Antennas and Accessories are available as mono-band or multi-band systems. Covering all five bands from 20 through 10 meters, DXE-TW-2010 Multi-Band Remote Switching Center Sections include a control console and cable and can be band-switched remotely in the shack and automatically by some transceivers. DXE-TW-2010L Multi-Band antennas can be band-switched manually. Plus, it's easy to change to the 80, 40 and 30 meter operations with DXE-TW-8080, DXE-TW-4040 or the DXE-TW-3030. Swap out each Band Box Center Post to change to operations on these different bands in a very simple manner. Typical installation for TW Antennas is a compact 8.25 ft. tall and only 5 ft. wide. Make your choice; portable, fixed or both, then equip yourself with the best compact vertical-dipole antennas available. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering HF Portable TW Antennas and Accessories are here to help you enjoy working stealthy HF at home or… anywhere! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
( 20 )
$595.99
DX Engineering TW Antenna 40 Meter Solo Explorer Packages
Preserving and building upon the legacy of this premier portable HF antenna line, DX Engineering is now the manufacturer of TW Antennas!* DX Engineering's acquisition of the products and designs of these unique HF portable and stealthy antennas brings easy access and simplified ordering to this antenna line formerly known as Transworld. DX Engineering TW Antenna 40 Meter Solo Explorer Packages include everything you need to go portable! The package is comprised of the basic antenna structure, the band box and an antenna stand. You supply the coax and your own powered transceiver. It's a great antenna for portable Low-Band QRP! Naturally stealthy, these compact HF vertical-dipole TW antennas feature a black powdercoat finish that is excellent for antenna use in HOAs. Use them where "CC & R" antenna restrictions preclude the installation of towers or easily-visible HF antennas. Simply unfold the DXE-TW-BAS-BLK Top and Bottom Sections, add your Band Box Center Post section, and place the antenna on the antenna stand and operate! No radials are needed with these 40-meter vertical dipoles! Ideal for portable use, the lightweight Quadrastand, DXE-TW-AQ, lets you set up your DX Engineering HF Portable TW Antenna wherever you happen to be. Think about special operating events like Scouts Jamboree On-The-Air (JOTA), Field Day or even SOTA (Summits On-The-Air). For general camping and travel, a convenient and durable carrying case, DXE-TW-DXBAG, is OPTIONALLY available to make transporting these antennas in your car or RV a snap! Typical installation for TW Antennas is a compact 8.25 ft. tall and only 5 ft. wide. Make your choice; portable, fixed or both, then equip yourself with the best compact vertical-dipole antenna available. Note: Although a permanently-installed mount is available, DX Engineering TW Antenna band boxes are not waterproof. Do not leave your TW Antenna exposed to the elements. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering TW Antenna 40 Meter Solo Explorer Packages are here to help you enjoy working stealthy HF at home or… anywhere! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
( 2 )
$748.96
DX Engineering Dual Input Remote Antenna Switches
DX Engineering Dual Input Remote Antenna Switches are two-radio 8-antenna switches (2x8) designed to switch coaxial lines in medium to high power RF antenna systems. With excellent performance on HF and 6 meters, they are typically used in single operator two-radio (SO2R) or multi-two contesting stations. They offer high levels of port-to-port isolation and reliability, the same as the famous DX Engineering RR8 series single input 8-port remote antenna switches. Manual dual-control operation of the DXE-RR2X8B is possible with two separate 1-of-8 control consoles that send +13.8VDC to the selected port, such as the DXE-EC-8. In this instance, the main transceiver has precedence over the secondary when attempting to use the same antenna port, so manual switching care must be exercised. An alternative first come, first served switching approach is available with the optional DXE-MX2X8 Interface Unit. It accepts BCD signals from two DXE-CC-8A Deluxe Control Consoles, and it locks out the selected port from the other radio, rather than main port precedence. DX Engineering RR2X8B Dual Input Switches may be interfaced with a customer-supplied logical switching unit. A third-party antenna controller with dual 1-of-8 switching may be used directly with the DXE-RR2X8B Switch or with BCD to the DXE-MX2X8 Interface Unit. If the DXE-MM2X8 Interface Unit is not used, the third party unit must provide protection against hot switching and prevent the main or secondary radio ports from attempting to select the same antenna port at any time. DX Engineering Dual Input Remote Antenna Switches feature a custom-made stainless steel chassis and a special RF shielded high impact thermoplastic cover. They have a custom conductive gasket to complete the seal between the cover and stainless steel housing base. Disassembly is not required for control wiring access. DX Engineering RR2X8B switches use removable screw terminals for the control cable plugs. These removable plugs greatly simplify installation by eliminating the need for soldering or opening the enclosure. The internal, covered relays are moisture-resistant, providing many years of exceptional performance. The circuitry of the DXE-RR2X8B switches allows the simultaneous selection of multiple antenna port with the required control signals. They can be used in complex antenna systems including stacked and phased arrays. Also, conventional one-of-eight antenna switching for two separate stations is possible using separate 1-of-8 switching arrangements. For example, the main radio Input "M" may select and be connected to any of the 8 ports while the secondary Radio Input "S" can simultaneously select any of the ports that the main isn't using. The main controller always has precedence over any selection made by the secondary controller, unless the DXE-MX2X8 is employed. Features of DX Engineering Dual Input Remote Antenna Switches include: * Rugged, attractive, fully shielded weatherproof housing * DX Engineering stainless steel V-clamp included for easy mounting to tower legs or masts from 1-2 in. diameter * Multi-conductor external cable plugs for easy removal, connection and maintenance * Excellent port-to-port Isolation; greater than 70 dB at 30 MHz, worst case; greater than 60 dB up to 60 MHz * High RF tolerant UHF connectors * Enclosed 16 ampere RF relays * Safe 12V DC relay operation * 16 MOVs for surge protection on control lines * 16 RF bypass capacitors Note: Whenever the DX Engineering "Documentation" is available, please look at the associated files for additional product information. Make your SO2R or other multi-radio multi-antenna operations easy with a DX Engineering Dual Input Remote Antenna Switch.
( 3 )
$669.99
DX Engineering PRO-STACK Broadband Antenna Phasing Switches
DX Engineering PRO-STACK Broadband Antenna Phasing Switches are newly designed to combine two identical Yagi or log periodic beams, or three quarter-wave vertical antennas, into a phased array for enhanced operation. There is no need for coaxial delay lines with the DX Engineering PRO-STACK switches. Just connect your antennas to the phasing switch controller with equal-length 50 ohm lines. PRO-STACK switch units are available with high-quality PTFE-silver plated SO-239 (UHF female) connectors. These relay units are 1-of-3 source voltage controlled at 12-15VDC over a four conductor cable. A matching Control Console is available separately or is included in the PRO-STACK System. These phasing switches can be used for any applications that require the following four basic antenna feed selections: both antenna ports in-phase, both antenna ports out-of-phase, antenna port 1 only, and antenna port 2 only. The default is both output ports in-phase. Impedance matching automatically changes when any antenna port is disconnected. Generally, stacked Yagi antennas are separated vertically greater than 1/2-wavelength free space. Since the DX Engineering PRO-STACK Broadband Antenna Phasing Systems are broadband, they may be easily adapted to larger arrays. For example, four stacked Yagis may be combined by creating two sets of two, and then using a third DX Engineering control console to combine the first two sets. PRO-STACK switches can also be used to feed three quarter wave resonant vertical antennas for a high-gain 4-pattern array. In this arrangement, the center #2 passive element is directly grounded to a good ground radial system at all times, while the end elements #1 and #3 are then fed in various phase relationships by the PRO-STACK. Details are in the complete PRO-STACK PS-2B Instruction Manual linked here in Documentation. Features of the DX Engineering PRO-STACK Broadband Antenna Phasing Switches include these great features: * Power handling up to 5 kW * Broadband coverage on 160-10 meters * High-impact RF shielded weatherproof housing * High-RF tolerant, silver-PTFE SO-239 (UHF female) connectors * Proven DX Engineering RF relays for high performance * Safe 12 VDC relay operation, even on battery or solar power * MOV surge protection on control lines * External, removable control line connector * RoHS-compliant assembly
( 1 )
$699.99
—
$740.00
DX Engineering Reversible Beverage Antenna System Combos
DX Engineering Reversible Beverage Antenna System Combos allow two Beverage antennas to be switched to receive in opposite directions while sharing the same physical space. These exciting new reversible Beverage combos include DX Engineering's superb receive preamp! Dramatically improved weak signal results can be achieved on MW, BCB, 160, 80 and 40 meter bands and shortwave bands with receive-only Beverage wire antennas that are typically 350 to 800 feet long, depending upon the lowest band of interest. DX Engineering Reversible Beverage System Combos are immune to the strong signal overload and core saturation common in multi-transmitter contesting environments. Reversible Beverages have two antenna F connectors; one "Away" port for the default end-fire receiving pattern off the end of the wire, and one "Toward" port for the opposite direction. Applying a negative 10 to 18 V DC to the feedline switches the system between the two antenna ports for reception in opposite directions. You can build a 4-direction receive antenna system with two reversible Beverage systems and one DX Engineering RLS-2 Two-Port Receiving Switch that also requires only one feedline! The optional DX Engineering Feedline Voltage Coupler, model DXE-FVC-1 is highly recommended to provide all of the required feedline voltage injection. Plus, the optional DXE-EC-4 BCD Control Console completes the system for four-direction switching right in the shack. These RBS systems will work with any 300-600 ohm 2-wire line. For best low-loss low-noise results, use DX Engineering flooded or quad-shielded 75-ohm coax; with our F-type compression connectors to ensure a weatherproof installation. DX Engineering RPA-1 Receive Preamplifiers use RCA-type phono jacks and CATV Type-F female connectors for the input and output connections to prevent accidental connection to transmitting devices. RPA-1 Receive Preamplifiers feature a built-in relay that automatically bypasses the preamplifier circuit when DC power is removed. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 V DC input. Details for DX Engineering Reversible Beverage Antenna System Combos: Receive preamp: * Gain: 16 dB, +/- 1.5 dB, from 300 kHz through 35 MHz * Dynamic range (IM3) at 500 Hz BW: 110 dB or greater * Output Third Order Intercept: +43 dBm * Noise figure: 3.5 dB * Compression: 1 dB at +26 dBm (nominally 0.4 W output) * Power requirement: 12-18 V DC at 140 mA maximum * Power Input: 2.1 mm DC coaxial power connector Reversible Beverage transformer features: * Broad operating range, 0.2 to 30 MHz * Fully isolated grounds prevent common-made noise and unwanted signals * 75 ohm design enables the use of high quality, low cost cable and connectors * RF shielded housing used for isolation and improved life * Directional Switching Voltage: nominal 12 V AC or negative 12 V DC, feedline injected * Directional Switching Current: less than 80 mA * Antenna impedance: 300-600 ohm (450 ohm recommended) * Feedline impedance: 50-75 ohm (75 ohm recommended) * RBSA-1FP Feed Point unit dimensions: 5.5 in. width x 3.5 in. depth x 1.5 in. height * RBS-1RT Reflection Transformer unit dimensions: 2.125 in. width x 2.125 in. depth x 1.125 in. height Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Reversible Beverage Antenna System Combos offer package convenience and superior receiving results on today's crowded medium and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the exceptional performance of DX Engineering products. Order one of these DX Engineering Reversible Beverage Antenna System Combos to make the best of your MW/HF reception!
Not Yet Reviewed
$605.97
DX Engineering TW Antenna 30 Meter Solo Explorer Packages
Preserving and building upon the legacy of this premier portable HF antenna line, DX Engineering is now the manufacturer of TW Antennas!* DX Engineering's acquisition of the products and designs of these unique HF portable and stealthy antennas brings easy access and simplified ordering to this antenna line formerly known as Transworld. DX Engineering TW Antenna 30 Meter Solo Explorer Packages include everything you need to go portable! The package is comprised of the basic antenna structure, the band box and an antenna stand. You supply the coax and your own powered transceiver. It's a great antenna for portable Low-Band QRP! Naturally stealthy, these compact HF vertical-dipole TW antennas feature a black powdercoat finish that is excellent for antenna use in HOAs. Use them where "CC & R" antenna restrictions preclude the installation of towers or easily-visible HF antennas. Simply unfold the DXE-TW-BAS-BLK Top and Bottom Sections, add your Band Box Center Post section, and place the antenna on the antenna stand and operate! No radials are needed with these 30-meter vertical dipoles! Ideal for portable use, the lightweight Quadrastand, DXE-TW-AQ, lets you set up your DX Engineering HF Portable TW Antenna wherever you happen to be. Think about special operating events like Scouts Jamboree On-The-Air (JOTA), Field Day or even SOTA (Summits On-The-Air). With robust 30 meter digital modes, DX contacts will be oh-so easy! For general camping and travel, a convenient and durable carrying case, DXE-TW-DXBAG, is OPTIONALLY available to make transporting these antennas in your car or RV a snap! Typical installation for TW Antennas is a compact 8.25 ft. tall and only 5 ft. wide. Make your choice; portable, fixed or both, then equip yourself with the best compact vertical-dipole antenna available. Note: Although a permanently-installed mount is available, DX Engineering TW Antenna band boxes are not waterproof. Do not leave your TW Antenna exposed to the elements. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering TW Antenna 30 Meter Solo Explorer Packages are here to help you enjoy working stealthy HF at home or… anywhere! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
Not Yet Reviewed
$748.96
DX Engineering RT4500HD Rotator Control Extension Cables
DX Engineering RT4500HD Rotator Control Extension Cables are premium pre-assembled cables with the appropriate 4-pin mating connectors installed for the DX Engineering RT4500HD Rotator. They eliminate the time-consuming task of soldering two additional optional connectors onto a long control cable. Designed for durability, these 4-conductor cable assemblies are rugged, yet flexible and are built to last with heavy duty stranded copper conductors and industry leading direct-bury polyethylene (PE) black jacket that is impervious to water and highly resistant to sunlight UV. Two 12AWG wires are for DC supply to the rotator motor and two 18AWG wires are for the rotator Pulse Sensor. One end of the cable features an interlocking weather-sealed 4-pin DXE-LP20-F female connector that mates with the RT4500HD rotator pigtail male connector. The 4-pin DXE-LP20-M cable mount male connector on the opposite end of this extension cable is intended to be connected to the controller pigtail. The DXE-LP20-F Rotator Control Line cable-mount female connector supplied with the RT4500HD, along with any convenient length of DXE-CW1812OR Heavy-Duty Spec Rotator Cable (sold separately), can be used to make a permanent pigtail with appropriate ring terminals for the screw terminal connections on the rotator controller. The use of the pigtail and this Rotator Control Extension Cable with mating connectors supports easy disconnection of the controller for additional surge protection and for simplified equipment repositioning. In this arrangement, the female receptacle connectors are appropriately used to supply power. Cable mounted male connector exposed pins are never energized when they are disconnected from their mate, thereby eliminating an accidental short circuit to ground. NOTE: At the appropriate point along the run, this cable may be cut, split, prepared and terminated for connection to a grounded surge protection device. Control Line Surge Protection, such as the DXE-CLTB-M or DXE-IS-RCT, is recommended to be installed at the grounding point of the tower base.
Not Yet Reviewed
$593.99
DX Engineering RR8B Remote Antenna Switch and Control Console Packages
DX Engineering RR8B Remote Antenna Switch and Control Console Packages bring a new level of convenience to your antenna setup. These packages combine DX Engineering's 5 or 10 kW key-down switch, plus a CC-8A or EC-8 Control Console. RR8B series Remote Antenna Switches feature: * 0-54 MHz operation with industry leading port-to-port isolation * 5 or 10 kW versions * Fully RF shielded with high strength, UV-resistant cover, stainless steel mounting bracket, and hardware * Lightning protection is standard * Solderless, removable plug for easy installation of control line with no disassembly * Can be wired without disassembly * Can select individual or multiple ports for stacking and phased array applications * Safe 12V DC relay operation * Unused antenna ports are open by design; may be internally jumpered to be grounded when not selected CC-8A Consoles feature: * 1-of-8 control format * 8 front panel LEDs to indicate switch position (with adjustable brightness) * Rear panel external plug * Operates on your 12V DC source, ideal for battery or emergency ops * Ergonomic selector knob * Powder-coated metal housing EC-8 controller features include: * 1-of-8 control format * Green power LED * Operates on your 12V DC source, ideal for battery backup or EMCOMM * Ergonomic selector knob * Powder-coated metal housing Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When a complete remote antenna switching system is needed and high reliability is a must, DX Engineering RR8B Remote Antenna Switch and Control Console Packages are your best solution! * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
( 8 )
$739.98
DX Engineering Phased Array Quarter Wave Tuned Cables
DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.
( 3 )
$649.99
DX Engineering DVA Dual Vertical Array Systems
DX Engineering DVA Dual Vertical Array Systems are advanced phasing systems that have set a new standard for array performance with two ground-mounted verticals. Dual Vertical Array Systems include a compact DVA Phasing Relay Unit made specifically for an individual HF band and an EC-DVA Directional Control Console. DX Engineering Dual Vertical Arrays produce two opposite enhanced End-Fire Cardioid patterns and one Broadside-Omni pattern. Heavy-duty components handle over 2 kW continuous RF power for enhanced performance at low SWR over a wide bandwidth. The Dual Vertical Array end-fire directional patterns achieve a real front-to-back over 20 dB with typical array forward gain up to 3 dB over a single vertical. The greatest advantage of a Dual Vertical Array is that a tower and rotator are not required, as with a Yagi antenna. Especially for 160, 80, and 40, and even on the other HF bands, a Dual Vertical Array is mechanically simpler and safer. Here is a financially practical directional antenna that is much easier to install! These are great directional antenna systems for temporary and Field Day operation, as well as for permanent builds, because they ARE so much easier to install than a beam! If you are dissatisfied with your present system, are ready for an upgrade, or just need to get out of the tower game, the DX Engineering DVA is your answer! Refurbish an existing antenna system, equip your temporary array, or build a new phased array with a DVA. It's all on the ground, safe and simple: DX Engineering Dual Vertical Arrays offer a better way to enjoy a high-performance mono-band directional antenna. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 4 )
$575.98
—
$685.98