Availability
DX Engineering Antennas
DX Engineering Rope Guying Earth Anchors
DX Engineering Rope Guying Earth Anchors are designed for use on ropes to build a custom guying system for your vertical antenna. They are manufactured from high-quality steel and have a protective finish applied for long-lasting durability. DX Engineering Rope Guying Earth Anchors feature a specially designed twisted base to allow for easy installation in the ground. *Shaft Diameter: 0.5in. *Loop Height: 2.24in. (loop tip to outside top of the loop) *Anchor Length: 15.00in. *Anchor Width: 3.0in.
( 14 )
$8.69
DX Engineering Guy Rings
DX Engineering Guy Rings advance the art of stabilizing vertical rigid telescopic tubing. These newly engineered and incredibly strong Guy Rings are intended for rope guying DX Engineering, Hustler, and all brands of aluminum tubing vertical antennas, as well as the DX Engineering Telescoping Fiberglass and Aluminum Tubing Kits. Unlike the other guys' rings, DX Engineering Guy Rings have smoothed holes with no sharp edges, protecting your directly threaded ropes. Six 5/16 in. diameter attachment holes allow guy ropes to be properly spaced for three or four way guying systems. DX Engineering Guy Rings are made from the super strong, black UV resistant, glass-reinforced poly-resin material that was introduced with DX Engineering's Universal Wire Antenna Kits EZ-BUILD™ UWA Center-T and End Insulators. They are virtually impervious to extreme outdoor conditions and mechanical stress. If you have a DX Engineering wire antenna or UWA Kit, you will know that these Guy Rings are made to last and will set a new standard in rope guying attachments. With their 1/2 in. thick center hole shoulder, these Guy Rings simply slide over their respective tubing size and seat firmly against the top of the larger tubing section below. Three kits with eight sizes provide rope guying for a myriad of vertical tubing installations: - DXE-GR-2P has two guy rings that fit onto the trap tubing of the Hustler BTV Series Vertical Antennas - DXE-GR-4P has four larger guy rings for Heavy Duty Telescoping Fiberglass sets or aluminum tubing - DXE-GR-5P is the original set with sizes for Standard Telescoping Fiberglass sets or various sized aluminum tubing DX Engineering Guy Rings are so handy and inexpensive that you can have a set on hand, ready for your next antenna project. Order yours today!
( 87 )
$5.29
—
$9.29
DX Engineering Ring Terminals
DX Engineering Ring Terminals are designed for 14 AWG radial and antenna wire. They can be crimped, soldered, or crimped and soldered for maximum durability. The terminal wire ends fit 14 or 16 AWG with a clearance hole for a 1/4 in. diameter bolt. These ring terminals are perfect for adding more radials to your vertical antenna system.
( 32 )
$6.49
DX Engineering SO-239 Mounting Brackets
For those projects when you need to mount an SO-239 connector, DX Engineering SO-239 mounting brackets are just what you need! These laser-cut aluminum brackets can be mounted with a variety of SO-239 and bulkhead connectors. DX Engineering SO-239 mounting brackets feature four mounting holes that provide various bracket mounting possibilities to make your project quick and easy. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 7 )
$7.49
DX Engineering Replacement Tilt Base Hardware Kits
DX Engineering Replacement Tilt Base Hardware Kits are genuine replacement hardware kits for the tilt base antennas. They consist of all of the nuts, bolts, fender nuts, and flat and lockwashers needed to replace missing or damaged pieces. They do not include hardware for saddle clamps.
( 2 )
$5.99
—
$9.49
DX Engineering Nomad Guy Ring Kits
DX Engineering Nomad Guy Ring Kits provide a reliable solution for stabilizing DX Engineering NOMAD masts in a variety of operating conditions. Designed as durable guy rings specifically for NOMAD masts, these kits feature precisely placed holes that enable secure 3-way guying for improved support. They are engineered to fit both 0.260 and 0.855 inch outside diameter mast tubes. Each kit includes six convenient hooks for attaching guy ropes. Offered in a 2-pack, these guy ring kits help ensure the stability and performance that operators depend on in the field.
Not Yet Reviewed
$9.99
DX Engineering Single-Band Low Power Dipole Kits
DX Engineering Single-Band Low Power Dipole Kits offer a quick and hassle-free project for Amateur Radio operators, making them an excellent choice for both individual and club activities. The DXE-DWK Dipole Kits are designed for low power operation and come with all the essentials to build a dipole antenna: a center insulator, two end insulators and a right angle BNC connector.
( 5 )
$9.99
DX Engineering Carbon Fiber Mast Guy Rings
DX Engineering® Carbon Fiber Mast Guy Rings push the boundaries of vertical mast stabilization for rigid, telescopic tubing systems. Purpose-engineered for rope guying DX Engineering Premium Carbon Fiber Masts, these exceptionally strong Guy Rings represent a smarter, tougher approach to mast support. Unlike ordinary guy rings, DX Engineering Guy Rings feature precision-smoothed attachment holes with no sharp edges, safeguarding directly threaded guy ropes from abrasion and premature wear. Six evenly spaced 5/16 inch attachment holes provide ideal geometry for both three way and four way guying systems, ensuring balanced, reliable tension in real-world installations. Manufactured from a super strong, black, UV resistant glass reinforced poly resin, these Guy Rings deliver the same proven durability introduced with DX Engineering's EZ BUILD™ Universal Wire Antenna Kit Center T and End Insulators. They are virtually impervious to harsh outdoor environments, intense sunlight, and heavy mechanical stress. Anyone familiar with DX Engineering wire antennas or UWA Kits will immediately recognize the quality—these Guy Rings are built to last and set a new benchmark for rope guying attachments. Each ring features a ½ inch thick center hole shoulder that easily slides over the appropriate tubing size and seats firmly against the top of the lower mast section, providing positive positioning without slipping or shifting. Smartly priced and incredibly versatile, DX Engineering Carbon Fiber Mast Guy Rings are the kind of essential hardware you'll want to keep on hand.
Not Yet Reviewed
$9.29
DX Engineering Band Link Kits
DX Engineering Band Link Kits (DXE-LINK-KIT) are insulators and wire clips, used to "add a band" to a portable wire antenna. These are the same band link parts as supplied with the DX Engineering Low Power Portable Dipole and Winder Kits. Band Links make manual band changes 'quick and easy' on portable 'low-to-the ground' resonant portable dipoles deployed as center-fed single support inverted-vee antennas, and on resonant end-fed antennas. Band Links are sold as a pair for a dipole. Alligator clips on the corresponding pair of Band Links are disconnected to change the dipole to the next higher band and are connected to change the resonance to the lower band. Only one link changes the band on a resonant end-fed wire. Band Links can be used to change the resonant (low SWR) frequency of a dipole or end-fed from CW to digital, and another to phone, and so on. Each DXE-LINK –KIT contains: • 2 Link Insulators – which support the wire and may be used to "break up" the wire antenna into multiband sections. • 4 Alligator Clips - two per Band Link. Two Band Links, one for each wire antenna leg, are included with the DX Engineering Low Power Portable Dipole and Winder Kit to make it a two-band antenna. Adding this second pair would make the dipole a three-band antenna, and a third pair will make the dipole a four-band resonant antenna, and so on.
Not Yet Reviewed
$8.99
DX Engineering MMP-P3 Multi-Purpose Mounting Plates
Fabricated from a tough but workable black polymer plastic, DX Engineering MMP-P3 Multi-Purpose Mounting Plates are easily modified with standard hand tools to allow you to customize these plates to your creative application. These polymer plates have a durable matte-textured surface on both sides. MMP-P3 plates are offered undrilled for your specialized uses. See our MMP-P1 pre-drilled plates for application where the plate can be mounted with a V-Bolt Saddle Clamp. Possible mounting applications for these plates include but are not limited to meters, switches, LEDs, and light bulb indicators as well as a wide range of small antenna building jobs. Their high dielectric, non-conductive properties means they're perfect for all kinds of electronic and other mounting projects. DX Engineering MMP-P3 Multi-Purpose Mounting Plates are ready for your simple needs or for your most imaginative projects! So have some on hand for your next brainstorm - order today!
( 1 )
$9.99
DX Engineering Hustler Resonator Set Screw and Tool Replacement Kit
When you lose or damage the 10-32 set screws or the matching hex key, turn to DX Engineering Hustler Resonator Set Screw and Tool Replacement Kits. These hardware and tool kits contain four 10-32 x 1/8 in. socket head set screws and one 3/32 in. hex key—plus they fit all Hustler resonators and Super resonators including the RM-80S that comes with the 5BTV and 6BTV HF base verticals. Get back on the air with an assist from DX Engineering Hustler resonator set screw and tool replacement kits!
Not Yet Reviewed
$5.99
DX Engineering Replacement Clamping Hardware for Mast Clamp
DX Engineering Replacement Clamping Hardware for Mast Clamp is available in two size specific versions: - DXE-RTMC-2A-HWK for the DXE-RTMC-2A Rotator Top HD 2 Inch Mast Clamps - DXE-RTMC-3A-HWK for the DXE-RTMC-3A Rotator Top HD 3 Inch Mast Clamps Each kit includes the appropriate stainless steel bolts, washers and single-use Nylon lock nuts. These kits are to be ordered as replacements for reuse and reinstallation of Mast Clamps because Nylon lock nuts are not recommended to be reused. NOTE: These replacement hardware kits are used for the clamping action, NOT for mounting, of Rotator Top HD Mast Clamps.
Not Yet Reviewed
$9.99
DX Engineering MMP-P2 Multi-Purpose Mounting Plates
Fabricated from a tough but workable black polymer plastic, DX Engineering MMP-P2 Multi-Purpose Mounting Plates are easily modified with standard hand tools to allow you to customize these plates for your creative application. These polymer plates have a durable matte-textured surface on both sides. MMP-P2 plates are offered undrilled for your specialized uses. Possible mounting applications for these plates include but are not limited to meters, switches, LEDs, and light bulb indicators as well as a wide range of small antenna building jobs. Their high dielectric, non-conductive properties means they're perfect for all kinds of electronic and other mounting projects. DX Engineering MMP-P2 Multi-Purpose Mounting Plates are ready for your simple needs or for your most imaginative projects! So have some on hand for your next brainstorm - order today!
Not Yet Reviewed
$8.99
Clearance
DX Engineering Rope Hardware Kits
DX Engineering Rope Hardware Kits are exactly what you need for all kinds of antenna projects that use support rope. Designed especially for use in conjunction with Mastrant Antenna Support Rope, these rope hardware kits provide just the right size pulleys, shackles, rope clips, duplex clips, carabiners, thimbles and quick links to facilitate fast and easy rigging, raising and lowering of wire antennas and guying of vertical antennas and antenna supports. They're great for experimenters, SWLs and Radio Amateurs who need to frequently adjust or "tinker" with their antennas. When used with new wire antenna installations, these products and Mastrant Antenna Support Rope allow for easy trimming or retuning of mono and multiband dipoles, end-feds, slopers and all types of wire antennas. Just lower, trim, and raise your antenna again until it's just right. For vertical antennas and support masts, use these kits for an installation that can be adjusted and disconnected easily, without having to constantly re-tie knots and deal with tangled excess rope. These kits feature stainless steel and metal-alloy parts for excellent durability and weather resistance. They will last a very long time. Are you raising a wire or vertical antenna or mast, or are using support rope on another project where strength and convenience are equally important? Consider using Rope Hardware Kits from DX Engineering for a professional looking project that really is stronger and is SO much easier to work on!
( 33 )
$25.99
$9.10
DX Engineering Rotator Mounting Replacement Hardware Kits
DX Engineering Rotator Mounting Replacement Hardware Kits are the same mounting hardware kits included with the DXE-RT4500HD Heavy Duty Rotator. These kits include four 5/16-18 x 3/4 in. 18-8 stainless steel patch bolts, which are the type that have thread-locking compound infused into the threads of the bolts. Stainless steel flat washers are included.
Not Yet Reviewed
$9.99