Selected Filters


Availability


DX Engineering HAM Radio Equipment

DX Engineering HAM Radio Equipment

DX Engineering offers the top brands in the ham radio industry—none better than our very own DX Engineering products. From our station accessories and antennas...

DX Engineering offers the top brands in the ham radio industry—none better than our very own DX Engineering products. From our station accessories and antennas right down to the cable assemblies, clamps, and hardware that bring it all together, DX Engineering products are made with superior materials, expert engineering—and no compromises! Build a better ham radio station with our heavy-duty rotator, steel masts, thrust bearings, remote antenna switches, fiberglass and aluminum tubing, element and saddle clamps, antenna building parts, our full line of coaxial cables, cable assemblies, connectors, high-quality...

DX Engineering offers the top brands in the ham radio industry—none better than our very own DX Engineering products. From our station accessories and antennas right down to the cable assemblies, clamps, and hardware that bring it all together, DX Engineering products are made with superior materials, expert engineering—and no compromises! Build a better ham radio station with our heavy-duty rotator, steel masts, thrust bearings, remote antenna switches, fiberglass and aluminum tubing, element and saddle clamps, antenna building parts, our full line of coaxial cables, cable assemblies, connectors, high-quality tools and a wide selection of accessories. Maximize performance with DX Engineering verticals and dipoles, add-on kits, baluns, RF chokes and ununs, transmitting array systems, receiving antennas and arrays, our receive phasing unit and more. Keep your station in peak condition with weatherproofing kits, grounding clamps, plates, surge protectors and copper straps. All DX Engineering products are engineered to be the best. See for yourself—shop now!

Part Groups

Results 1 - 24 of 26

DX Engineering Receive Eight Circle Array Controller and Switch Package

DX Engineering Receive Eight Circle Controller and Switch Package, DXE-RCA8C-SYS-2P, is for the array builder who wants to use their own passive receive verticals for a mono-band receive array. The DX Engineering Eight Circle Array will dramatically improve reception of weak distant signals with unparalleled rejection of extraneous signals and noise. This eight-direction switchable array uses a special end-fire/broadside combination of eight short receiving vertical elements. The resulting narrow directional receiving pattern is superior to standard or short Beverage antennas, Reversible Beverage systems and typical two, three or four element arrays. Receive arrays of short vertical elements limit signal and noise for dramatically superior weak signal reception as compared to full size transmitting antennas and arrays. With proper spacing of eight vertical elements, the Receive Eight Circle Array is the ultimate high performance, directional receive antenna for HF Amateur, SWL or AM DXing. DX Engineering Receive Eight Circle Arrays offer directional performance comparable to eight very long phased Beverages, using far less land area. These packages are designed to be used with eight identical, user-supplied, active or passive symmetrically-spaced vertical elements to provide switching for an 8-direction receiving antenna system. Passive elements will generally provide you with a monoband receiving system. With a DX Engineering Active Vertical package you can achieve excellent directional receiving performance over three bands. Click "More Details" below for additional information, features and specifications. The "Documentation" link contains manuals and associated files for complete product installation information. Build an exceptionally effective, electronically rotatable, stationary receive antenna that lets you hear the DX that cannot be heard on a transmit antenna. Dig the weak signals out of the noise with an antenna that can help make your station one of the best. Order the DX Engineering Receive Eight Circle Controller and Switch Package.

Not Yet Reviewed

$815.98

DX Engineering Receive 8 Circle Array Controllers

DX Engineering RCA8C-1 Receive 8 Circle Array Controllers are the highly sophisticated switch controller relay units from the Eight Circle Array Systems--the receiving systems that use time delay phasing--rather than the conventional narrow-band, frequency-dependent phasing, to provide eight 45 degree spaced directional patterns. The RCA8C time delay phasing is directivity-optimized to produce wider and deeper rear nulls and a narrower main lobe. The result is that noise and undesirable signals are greatly reduced for a superior front-to-rear ratio (F/R). Better control of phase and currents provides a cleaner pattern with the Receive 8 Circle than is available with vertical antenna transmit arrays. DX Engineering Receive 8 Circle Array Controllers are designed to be used with eight identical vertical active or passive vertical elements, symmetrically spaced in a large circle, to provide switching for an 8-direction receiving antenna system. Passive elements will generally provide you with a monoband receiving system. Finally, these systems offer greater reliability in receiving applications. Receive Eight Circle Array Controllers use sealed relays sized for receiving applications with silver contacts to prevent oxidation and contamination. Most transmitting four-square switches use large open-frame relays where the contacts are exposed to the air, which can lead to contamination. Relays with brass contacts can oxidize, leading to poor conductivity. Receive Eight Circle Array controllers feature: * W8JI design * Operation from 100 kHz to 30 MHz * Excellent directivity for better signal-to noise ratio * Switching console provides eight 45 degree spaced directions * Less physical space and maintenance required than phased Beverage antennas * Low current DC powered control console allows system operation without AC power mains The optional DX Engineering Eight Circle Receive Short Element Active Vertical Antenna Package, DXE-RSEAV-8, offers excellent receiving performance from 100 kHz to 30 MHz, while using only a 8.5 ft. (2.6m) aluminum vertical antenna elements. A unique design makes the Receive Eight Circle Array System vastly superior to traditional active vertical antennas in both strong signal handling and feedline decoupling. This results in significantly better weak signal reception due to lower spurious signal interference and reduced noise. DX Engineering RCA8C Receive 8 Circle Array Controllers are the foundation of your Eight Circle Array!

Not Yet Reviewed

$499.99

DX Engineering Receive Four Square Array V3 Systems

DX Engineering Receive Four Square Array V3 Systems, DXE-R4S-SYS-V3, dramatically improve reception of weak distant MW and SW signals with excellent rejection of extraneous signals and noise. This is a four-direction switchable phased array that is able to cover multiple HF Amateur bands, such as 160, 80 and 40 meters, by using time delay phasing of four physically short active receive vertical elements. The resulting directional receiving pattern has deep back and side nulls that are superior to Beverage antennas and other receive arrays. The DX Engineering Receive Four Square Array is less susceptible to high angle signals than EWE, Flag, Pennant, K9AY and SAL antennas. Short vertical element receive arrays limit interfering signals and noise for dramatically superior weak signal reception, as compared to full size transmitting antennas and arrays. With the appropriate location and spacing of the four stealthy 8.5 ft. (2.6m) vertical elements, the Receive Four Square Array V3 System is a high performance, directional receive antenna for HF Amateur, SWL or AM DXing. Click or tap the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. DX Engineering Receive Four Square Arrays offer directional performance comparable to four long Beverage wire antennas, while using far less land area. In the appropriate clear area, away from metal, structures and other antennas, each of the four Actives simply mount inches above the earth onto a ground rod. Each element is installed on the corners of the array square with sides that are one-eighth to one-quarter wavelength on the lowest band. For example, the optimized Receive Four Square Array for 160, 80 and 40 meters has elements spaced 70 ft. apart. The DXE-R4S-SYS-V3 system includes the DXE-RFS-3 Receive Four Square Array Controller, four Receive Short Element Active Vertical Antennas, DXE-RSEAV-1, featuring the new DXE-AVA-3 Active Matching Units, insulating mounting plates and stainless hardware. These Active Antennas are packed in a 38 x 5 x 5 in. carton for lower shipping cost. Three sections of 3 ft. aluminum tubing, 0.500, 0.375 and 0.250 inch OD, assemble to a height of only 8.5 ft., so each self-supporting element is truly stealthy. This complete array system also includes the DXE-EC-4 Directional Control Console, one 1,000 ft. roll of quality RG6U cable, all cable prep tools, connectors and hardware for construction of the array. Required ground rods and control cable are purchased separately. Build an exceptionally effective, electronically rotatable, stationary receive antenna that lets you hear the DX signals that cannot be heard on a transmit antenna. Dig the weak signals out of the noise with an antenna that can help make your station one of the best. Order and install the DX Engineering Receive Four Square Array V3 System.

3.33 out of 5 stars ( 3 )

$1,929.39

DX Engineering Receive Eight Circle V3 Complete Array Systems

DX Engineering Receive Eight Circle V3 Complete Array Systems, DXE-R8C-SYS-V3, provide outstanding reception of weak distant signals. This eight-direction switchable array uses a special end-fire/broadside time delay phasing of eight stealthy 8.5 ft. (2.6m) active vertical elements to cover multiple HF Amateur bands. The Eight Circle pattern rejects extraneous signals and noise far better than Beverages and other arrays. With appropriately located elements, the Receive Eight Circle Complete Array System is the ultimate high-performance directional receive antenna for HF Amateur, SWL or AM DXing. –––––– Click or tap the title of a listed item for an Overview with a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation.

Not Yet Reviewed

$3,447.34

DX Engineering Receive Four Square Array Controllers

The patented DXE-RFS-3 DX Engineering Receive Four Square Array Controllers are the heart of a sophisticated receiving system that uses time delay phasing rather than the conventional narrow-band, frequency-dependent phasing systems. The time delay phasing is directivity-optimized to produce wider and deeper rear nulls and a narrower main lobe. The result is that noise and undesirable signals are greatly reduced for a superior front-to-rear ratio (F/R). Better control of phase and currents provides a cleaner pattern than those found on available transmit four square arrays. The RFS-3 DX Engineering Receive Four-Square Array Controllers are the switch relay units that are optimized to use the DX Engineering's Active Vertical Antenna Package DXE-ARAV4-4P of four active verticals. These products together offer great F/R response over octaves of bandwidth. DX Engineering's Active Receive Antenna System offers excellent receiving performance from 100 kHz to 30 MHz, while using only a 8.5 ft. antenna element. A unique design makes it vastly superior to traditional active antennas in both strong signal handling and feedline decoupling. This results in significantly better weak signal reception due to lower spurious signal interference and reduced noise. Finally, these systems offer greater reliability in receiving applications. The RFS-3s use sealed relays sized for receiving applications with silver contacts to prevent oxidation and contamination. Most transmitting four-square switches use large, open-frame relays where the contacts are exposed to air, which can lead to contamination. Relays with brass contacts can oxidize, leading to poor conductivity. Advantages of the RFS-3 Receive Four-Square Antenna Systems over other small or medium-size receiving arrays include: * Reduced susceptibility to high angle signals compared to EWE, Flag, Pennant, and K9AY antennas * Excellent directivity in a small space for better signal-to-noise ratio * Switchable in four 90 degree spaced directions * Directivity over a very wide frequency range using DX Engineering DXE-ARAV4-4P active elements * Less physical space required than a Beverage antenna, and active elements need only a minimal ground system * Enhanced relay contact reliability

Not Yet Reviewed

$375.99

DX Engineering Receive Four Square Array Electronics Package

DX Engineering Receive Four Square Array Electronics Package, DXE-RFS-SYS-2P, is for the array builder who wants to use their own passive receive verticals for a mono-band receive array. See the DXE-R4S-SYS-V3 for the Complete Receive Four Square V3 Array System with Receive Short Element Active Verticals. DX Engineering Receive Four Square Arrays dramatically improve reception of weak distant signals with excellent rejection of extraneous signals and noise. This four-direction switchable array uses time delay phasing of four physically short receiving vertical elements. The resulting directional receiving pattern is superior to four short Beverage antennas and typical two or three element arrays. The Receive Four Square is less susceptible to high angle signals than EWE, Flag, Pennant, K9AY and SAL antennas. This type of receive array, using physically short vertical elements, limits signal and noise for dramatically superior weak signal reception, as compared to full size transmitting antennas and arrays. With proper spacing of four unobtrusive, physically short vertical elements, the Receive Four Square Array System provides high performance directional receive for HF Amateur, SWL or AM DXing. Click or tap the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. DX Engineering Receive Four Square Arrays offer directional performance comparable to four long Beverage wire antennas, using far less land area. This Controller and Switch Console package is designed to be used with four identical, user-supplied, active or passive symmetrically-spaced ground-mounted vertical elements to provide switching for a 4-direction receiving antenna system. Passive elements will generally provide an optimized monoband receiving system. Conversely, with four DX Engineering Receive Short Element Active Vertical antennas, DXE-RSEAV-1, the properly sized array can achieve excellent directional receiving performance over three HF bands. Build an exceptionally effective, electronically rotatable, stationary receive antenna that lets you hear the DX that cannot be heard on a transmit antenna. Dig the weak signals out of the noise with an antenna that can help make your station one of the best; install the DX Engineering Receive Four Square Array System. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.

Not Yet Reviewed

$553.98

Hi-Z® Antennas Manual Directional Control Consoles

Hi-Z® Antennas Manual Directional Control Consoles are specialized "low-side" BCD grounding switches that are specifically designed to operate Hi-Z Antennas Phasing Combiner relay units, also known as Phase Controllers. Each HIZ-MDC console controls the phasing and direction selection of only Hi-Z Antennas Receive Vertical Antenna Arrays and supplies power to the array element amplifiers. Hi-Z Antennas Manual Directional Control Consoles are attractive and convenient, featuring a large rotary switch knob and green LEDs arranged as receive array directional azimuth indicators with corresponding compass bearing degree markings on the front panel. Selection of a specific model Manual Directional Control Console (MDC) is required, corresponding to each version of Hi-Z Antennas Receive Array Phasing Combiner or legacy Phase Controller. Each console serves as a replacement for legacy, discontinued Hi-Z manual Shack Switches, and for the discontinued Hi-Z SS-2 and SS-2PLUS: • HIZ-MDC-4 works only with the multiband Four Square Arrays PC-4A and PC-4ELEMENT • HIZ-MDC-8PRO works only with the 85/113 ft. diameter multiband 8 Circle Arrays PC-8PRO and PC4-8PROUP/PLUS • HIZ-MDC-8 works only with the 200 ft./100 ft. diameter monoband 8 Circle Arrays PC-8, PC-8A and PC-8B HIZ-MDC series Manual Directional Control Consoles are stylish, rugged, and heavy — they stay in place on the desk or shelf with four large non-skid rubber feet under a Stainless Steel chassis and an appropriate black powder coated steel cover. The required multi-conductor array power and BCD control cable (purchased separately for the required number of conductors and length to the array) passes through a grommet on the rear panel and connected internally. A rear panel 2.1mm +13.8VDC power connector accepts the included mating 2.1mm plug and unterminated DC power cable, for connection to a user provided +13.8VDC 1A fused, well-filtered power supply.

Not Yet Reviewed

$159.99

YCCC Vertical Array Directional Switch Console Kits

Closeout- Other YCCC array components are no longer available YCCC Vertical Array Directional Switch Console Kits were used to control the YCCC vertical array combiner/controller units, which have been discontinued. They feature an attractive cabinet with an ergonomic direction-selector knob and direction indicating LEDs. Power Pole type connectors are used for DC power connection. These kits require component-level assembly and soldering parts to a PCB. The switching console is installed in the shack, with the control cable run from the switching unit to the combiner/controller unit at the array. Power for the entire antenna system is provided by a 13.8V DC (1A capability or greater) power supply that the user must provide. Use of a "wall wart" type of power supply is not recommended because they generally have very poor DC regulation. These switch units are for use ONLY with YCCC vertical antenna arrays, which are discontinued and no longer available for sale. All inquiries and technical support for these YCCC kits and kit packages is handled by e-mail only, typically within two to three business days: yccctechsupport@verizon.net

Not Yet Reviewed

$60.00

DX Engineering Receive Short Element Active Vertical Antennas

DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.

4.75 out of 5 stars ( 4 )

$249.99

—

$1,999.92

DX Engineering AVA-3 Active Matching Units

DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.

5.0 out of 5 stars ( 6 )

$139.99

DX Engineering Receive Feedline Transformers

DX Engineering Receive Feedline Transformers are designed to match your receive antenna 75 ohm output impedance to the nominal 50 ohm input impedance of most receivers. These transformers may be used in almost any receiving application that requires a 75 ohm Type F connection to a 50 ohm BNC connector. These transformers have very low loss (<0.3 dB) and very wide bandwidth, 100 kHz to 30 MHz! Matching the receive antenna or array to the receiver ensures the best possible performance as a result of a system impedance match. *Important! - These Feedline Transformers are Intended to be used on an RF ONLY coax and should NOT be used for power.

5.0 out of 5 stars ( 1 )

$55.99

DX Engineering Receive Feedline Voltage Couplers

DX Engineering FVC-1 Feedline Voltage Couplers provide an interface between control switches and voltage-controlled antenna systems. These specialized controllable bias-tee devices place 0V DC, +12V DC, -12V DC, and 12V AC output voltages onto the receive antenna feedline via the 75 ohm F connector or onto a 2-conductor control line. These FVC-1 couplers function from below 500 kHz to 30 MHz and provide four selections for switching antenna array directions or changing from one array to another. These couplers were designed for use with; the DX Engineering receive-only four-square antenna systems, reversible Beverage antenna systems, and remote switches. DX Engineering switch control consoles may be connected directly to the BCD switch control input of FVC-1 couplers. Alternatively, you may use your own 12V DC voltage switching system or 1 of 4 grounding switches to control the coupler by resetting internal jumpers. The connection of the feedline voltage couplers to any radio receive antenna input is to be made using either the standard RCA phono or the F connector. This allows for the use of readily available RF-compatible RCA phono patch cords or a 75 ohm coaxial cable and connectors, which protects your receive system from an accidental connection to transmitting equipment. FVC-1 feedline voltage couplers have two LED indicators--red and green--which indicate the presence and polarity of the output control voltage selected. The LEDs may function as directional indicators that can be read at a convenient distance or they can aid in troubleshooting. Each of our DX Engineering FVC-1 Feedline Voltage Couplers comes with a heavy duty 120V AC wall transformer, which provides a safe 12V AC to operate your receive antenna system. Here are other exclusive features of FVC-1 voltage couplers: * Metal housing--superior shielding, rugged, and easy mounting * Convenient installation--mount anywhere in your shack * Rugged control connector - a reliable, solderless, and removable connector with screw conductor clamps * Internal thermal reset fuse offers full protection against accidental shorts Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Got antenna switching voltages? DX Engineering FVC-1 Feedline Voltage Couplers will solve many switching needs easily and economically!

5.0 out of 5 stars ( 1 )

$185.99

DX Engineering 2-Port Splitter-Combiners

DX Engineering 2-Port Splitter-Combiners are receive signal-level RF devices that operate from 300 kHz to 30 MHz, available in 50 ohm and 75 ohm versions. They're typically used to split one RF signal to properly feed two receivers, or the receive antenna inputs of one transceiver and one separate receiver. They also properly combine two receiving antennas in phase, such as Beverage antennas, to form a phased receive array. Important features of the DX Engineering 2-Port Splitter-Combiner: * Available for 50 ohm and 75 ohm systems * Broad, 300 kHz through 30 MHz operating range * High-quality components * Isolated ports * Metal housing for superior shielding and longer life * Reliable side-mount connectors: BNC female for 50 ohm, F female connectors for 75 ohm model * Economical solution to potential impedance errors that cause losses With the updated "SC" versions of the original 2-Port Splitter-Combiner, DX Engineering has maintained the port isolation design that prevents signal performance degradation caused by impedance errors in less-than-perfect receive systems. The normal signal level reduction when used as a splitter is just over 3 dB per port. As with any system, losses are dependent upon source and load impedances being matched. DX Engineering Splitter-Combiners provide equal power, voltage, and current to matched loads on ports 1 and 2. The primary advantage is that individual receiver input variations, or a band filter attached to only one port, will not seriously affect the signal level in the other receiver. In addition, any spurious signals generated in one receiver are greatly attenuated by the 2-Port Splitter-Combiner before reaching the second receiver. When splitting in-phase signals, the loss is somewhat less. Any unused port of the 2-Port Splitter-Combiner should be terminated and specified losses are based on source and load impedances being matched. The DX Engineering 2-Port Splitter-Combiner is a passive device; therefore it requires no power to operate. Use the 75-ohm version for combining two 75 ohm antenna feedlines into a single 75 ohm feedline with negligible loss; or use the 50-ohm version for 50-ohm antennas and feedlines. Examples for applications are for two antennas forming an in-phase (broadside) receiving array, a cross-fire Echelon Beverage array, or any type of array with fixed phasing. There are a number of advantages to using these units for combining antenna systems over a standard parallel connection: * Splitter-Combiners match the entire antenna system to the feedline impedance; conversely, paralleling feedlines by using a T-connector divides the impedance in half, causing mismatched losses * With antennas connected directly in parallel, if either one develops a high impedance open, becomes shorted, falls down, or has a feedline problem, the entire antenna system may become unusable. By using the 2-Port Splitter-Combiner, only the problem antenna is unusable; the antenna on the other port can still be used * Unlike quarter wave matching sections that only work on one band, these Splitter-Combiners have extremely wide bandwidth * Due to the built-in isolation and balancing, these units limit the signal loss to approximately 3 dB per port * 2-Port Splitter-Combiners provide very high isolation between ports 1 and 2; this prevents either antenna from interfering with the other during normal operation Note: These devices cannot be used for FM broadcast, VHF, UHF, CATV or Satellite TV. They operate only MF through HF. Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.

5.0 out of 5 stars ( 5 )

$100.99

—

$107.99

YCCC Receive Feedline Choke Kits

Closeout- Other YCCC array components are no longer available YCCC Receive Feedline Choke Kits prevent common-mode noise or unwanted signal intrusion on the feed lines of YCCC Receive Vertical Array Kits. These choke kits are the same as provided in the array kit packages and may be used as replacements or in other applications. Component-level assembly of these kits is required. A choke enclosure is user supplied. Their function is to provide isolation between the input and output coaxial shield connections, while passing desired receive or control signals. Their isolation impedance blocks common-mode noise or unwanted signals. YCCC Receive Feedline Choke Kits are supplied with standard "F" female connectors to prevent connection to transmitting equipment. All inquiries and technical support for the discontinued YCCC kits and kit packages is handled by e-mail only, typically within two to three business days: yccctechsupport@verizon.net

Not Yet Reviewed

$22.00

DX Engineering NCC-2 Receive Antenna Phasing Systems

Imagine adjusting the controls to knock out strong interfering stations or noise—and then being able to copy and log that weak DX station. By successfully combining the right antennas with the advanced phasing capabilities of the NCC-2, this is the operating thrill that every radio enthusiast can enjoy, again and again! DX Engineering NCC-2 Receive Antenna Phasing Systems are variable phasing controllers that combine the 300 kHz- 30MHz received signals from one transmit antenna and one receive antenna, or from two dedicated receive antennas. Combining signals from two stationary antennas physically spaced 1/10 to 1/2 wavelength apart creates an array pattern with signal peaks and dips called nulls. Adjusting the NCC-2 Phase and Balance controls have the effect of electronically rotating or steering that pattern. Steering the null direction to significantly weaken a local or distant interfering signal or noise is known as "Noise Cancelling." This "Noise Cancelling Controller" (NCC-2) can dramatically enhance the reception of weak signals from non-null directions. This "reverse-beam" capability on radio frequencies AM Broadcast through HF can provide amazing benefits for many types of AM DX and SWL receiving and ham radio operating. Work new DX, hear the weak station in casual regional conversations, snag the rare multiplier in contests and hear beyond the noise and interference in dire circumstances. DX Engineering NCC-2 Phasing Systems now feature the built-in RTR Receive-Transmit Interface relay system that expands the exciting benefits of antenna phasing for interference reduction in two ways: * First, the NCC-2 can combine signals from the HF transmit antenna and a separate receive antenna to effectively notch-out strong stations or noise. Almost any Amateur can now enjoy the benefits of antenna phasing and noise-nulling, even those with space limitations for separating the receiving and transmitting antennas. * Second, the user of any standard HF transceiver that lacks a separate receive antenna input can have enhanced reception of noise and signal nulling with the DXE-NCC-2 and two antennas. Rear panel SO-239, F and BNC connectors make the NCC-2 extremely versatile and easy to connect to almost any receiver or HF transceiver up to 200 watts. Redesigned with plug-in modular circuit board sockets, the NCC-2 includes one switched and powered internal slot and two passive internal slots per channel to accommodate these new options: * DXE-RPA-2-PM Receive Preamplifier Plug-In Modules (powered): one per channel for low-signal passive antennas with poor ground conditions * DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module (passive): Front-end protection for the NCC-2 and the receiver * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-In Module (passive): to match 75 ohm RX ANT feedlines to NCC-2 50 ohm internal impedance * NCC-2 Receive Filter Sets (passive, non-switchable): High Pass, Band Pass and Low Pass Filters for 160, 80, 40 meters typically in stock, with other band filters available individually by special order. DX Engineering NCC-2 Receive Antenna Phasing Systems offer these new additional benefits: * Multi-Color Status Indicating LEDs for Power, RTR Mode and Preamp Power CH A and CH B * New Radio Key Line Input with RX Enable Output-RTR Failsafe to prevent RF damage to NCC-2 and RX equipment * New ACC Key Line Output RCA female 'ground on transmit' pass-through for Amplifier or Accessory * New screw-on 2.1mm DC connector to prevent accidental power cable pull-out * Operates on +13.8VDC @ 2A input to power the NCC-2 and internally jumper set Bias Tee on each RX ANT ports for coax fed Active Verticals and other accessories. Offering new and experienced radio enthusiasts the next level of reception enhancements, DX Engineering model NCC-2 Receive Antenna Phasing Systems in use around the world!

4.89 out of 5 stars ( 19 )

$955.99

DX Engineering Phased Array Quarter Wave Tuned Cables

DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.

4.67 out of 5 stars ( 3 )

$137.13

—

$899.99

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.

Not Yet Reviewed

$249.99

—

$1,299.99

DX Engineering Transceiver Amplifier Keying Cables

DX Engineering Transceiver Amplifier Keying Cables connect the "ground on transmit" or contact closure provided by the radio that is required to make an HF amplifier switch from "receive mode" to "transmit and amplify mode" when using PTT (push-to-talk), VOX or break-in CW keying. DX Engineering Transceiver Amplifier Keying Cables are made for specific transceiver models that have special DIN or mini-DIN connector accessory ports which provide the transceiver's only connections for linear amplifier keying. One type of amplifier keying cable has one RCA phono plug for the amplifier relay jack, which is all that is needed. When the transceiver PTT (push-to-talk) is keyed, the RCA plug center pin is connected to the shield (and chassis ground in most cases) to key the amp relay or its solid state keying circuit. Instead of a direct connection to the amp relay, the RCA plug may be connected to the keying input of an accessory device (DXE-KEYLINE-3, DXE-RTR-2 or DXE-NCC-2), amplifier keying interface (DXE-SV-KR or legacy Ameritron ARB-704 or KD9SV Products SV-KR) or other amp keying line interrupt device, such as a meter or an array controller. Each has a keying input and a keying output for the amplifier relay or another accessory. Another type of amplifier keying cable has two RCA phono plugs, one RED plug for the amplifier relay jack and one WHITE plug for ALC (Automatic Level Control) voltage from the amplifier. The legacy ALC connection does not need to be used with present era solid state transceivers and most modern amplifiers. ALC was required for use on transmitters with tube finals. Some modern amplifiers do not have an ALC output connector. If the amplifier does not have ALC it is okay to leave the WHITE plug disconnected. Order your DX Engineering Transceiver Amplifier Keying Cables to connect to your transceiver accessory port for keying amplifiers, sequencers, receive-transmit interfaces, buffer relays, and other accessories. NOTE: To enable the function of this keying cable, some late model Kenwood transceivers require menu activation of the amplifier keying circuit.

4.8 out of 5 stars ( 51 )

$36.99

—

$59.99

DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable

DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable is our top-of-the-line, direct-bury RG-6. It has low RF signal loss and provides greater protection against electromagnetic interference. Available cut-to-length by-the-foot or in 1,000 ft. spools, this is the best ultra-high quality RG-6/U self-healing quad-shield cable solution. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. DXE-RG-6UFQ cable is ideal for many receiving applications including active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution and satellite radio installations such as Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up through microwave frequencies of satellite radio systems! Our RG-6 flooded quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding. The waterproof UV protected black jacket is made with a tough and flexible polyethylene (PE). This cable is infused with a flooding compound that provides a permanent barrier to moisture and is self-healing to minor cuts. The nominal impedance of DXE-RG-6UFQ cable is 75 ohms with a nominal Velocity Factor of 82% (VF = 0.82). The minimum bend radius is 2.500 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? DX Engineering RG-6U 75-ohm Flooded Quad-Shield Coaxial Cable is absolutely the best RG-6 quad-shield cable available and it is RoHS compliant! Check these super low attenuation figures! 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? If so, then order the new benchmark in RG-6 cable: DX Engineering RG-6U 75-ohm Flooded Quad Shield Coax. Your efforts will be rewarded with the results that you expect, using the best cable from DX Engineering.

4.78 out of 5 stars ( 9 )

$0.37

—

$255.99

DX Engineering Shielded Control Cable

DX Engineering Shielded Control Cable is a high quality shielded cable that is suitable for indoor or outdoor use. It features nine #24 AWG annealed tinned copper stranded conductors with color coded PVC insulation and aluminum foil shielding, plus a bare #24 AWG stranded tinned copper drain wire. This RoHS compliant cable supports an eight port remote switch with 1-of-8 control lines plus a common ground conductor AND a separate shield conductor. This cable has a thick, durable, chrome-gray PVC jacket. Plus, using a cable that has stranded conductors relieves the worry of breaking one of the conductors; unlike a different type of cable made with solid wire. This shielded control cable is ideal for use with DX Engineering Remote Antenna Switches, Four Square and Phased arrays, and should be considered a great choice for any of your low-current, custom remote switching applications. This cable is excellent for building accessory cable assemblies, RS-232 data cables, switching cables, and for control of low-voltage relays including receiving and transmitting antenna arrays. This cable is not intended for use with rotators or other medium current applications. You may order DX Engineering Shielded Control Cable by the foot in any lengths up to 500 feet and is available in a 1,000 ft. roll. Here are the "specs" on this very useful shielded control cable: Number of stranded conductors: 10 Number of insulated conductors: 9 Insulated conductor AWG (Strands): 24 (7/32) Drain wire AWG (Strands): 24 (7/32) Insulation nominal wall thickness: 0.010 in. Nominal Capacitance (pF/ft.): 30 Jacket nominal wall thickness: .035 in. Nominal outer diameter: 0.240 in. Cable Temperature Range: -20 to 80 degrees C Cable Voltage: 300 V

4.88 out of 5 stars ( 8 )

$2.09

—

$2,089.99

DX Engineering TFS4 Series B Transmit Four Square Systems

DX Engineering TFS4 Series B Transmit Four-Square Systems bring together the highest level of engineering excellence with the practical realities of operator convenience and ease of installation. These four-square hybrid systems are available in versions for the 160, 80, and 40 meter bands. They can be easily dropped into your quarter-wave spaced vertical 4-antenna array to provide optimum directional control. They allow the operator to receive or transmit with 5.5 dB gain in any one of four directions with a 20+ dB front-to-back ratio for interference reduction from unwanted directions. You can also switch to a single Omni-directional pattern with a push of a single button. This combination permits you to listen "all-around," unhindered by pattern nulls, and then select the best direction for signal reception and noise rejection. TFS4 Series B Transmit Four Square Systems are designed for use with four monoband vertical antennas placed at the corners of a square that is one-quarter wavelength on a side. The vertical element must be ungrounded and resonant in the desired band, and should be directly base-fed by the coaxial cable phasing lines from the centrally located controller (shunt-fed towers or radiating elements cannot be used). DX Engineering has several vertical antennas that are well suited for this application. Above all, a properly designed and installed radial system is necessary for top antenna performance, whether it's a single vertical or a full array. DX Engineering strongly recommends our optional Q75- series quarter wavelength cables constructed from our own high quality DXE-11U coax. It features a waterproof PE jacket, foam dielectric and has a velocity factor of 82 percent. These cables are electronically pruned to a precise electrical length derived from your choice of center operating frequency, terminated with hand-soldered silver-PTFE PL-259 connectors and weather-sealed with shrinkable tubing. Finally, each cable is tested for high voltage breakdown for maximum reliability and power handling. Since the transmit power is divided by the controller, the coaxial cable can handle QRO power with ease. If you already have a four-square array with a hybrid controller and would like to upgrade to improved performance and the Omni feature, the DX Engineering TFS4 Series B Transmit Four Square Systems are a direct transplant. BCD logic switching allows for the use of a 4-wire control cable to perform the necessary switching functions when powered by the included control console. Features: * Classic hybrid design is easy to install * Four directions plus Omni for versatile operation * 5 kW CW power rating for high reliability * Hot switching lock-out to disable amplifier while switching * Drop-in replacement for COMTEK systems * Proven DX Engineering RF relays for high performance * RF Shielded, high impact thermoplastic cover offers unique protection * Relays cycle during Power-On to ensure clean contacts Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Four-square systems work great! DX Engineering TFS4 Series B Transmit Four-Square Systems provide the heart of a modern phased array.

Not Yet Reviewed

$807.98

—

$831.98

DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable

DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable is our regular RG-6U with a Type II PVC jacket, low loss and greater protection against electromagnetic interference. Available cut to length or in 1,000 ft. spools; this is a high-quality standard RG-6U quad-shield cable. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. (Please Note: Also available is our waterproof direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ-CTL and DXE-RG6UFQ-1000.) DXE-RG-6UQ cable is ideal for many applications, such as active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution as well as satellite radio installations like Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up to the microwave frequencies that Satellite Radio systems employ! Our RG-6 quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding and the UV protected black jacket is made with a tough, but very flexible, PVC. The nominal impedance of DXE-RG-6UQ cable is 75 ohms, and it has a nominal Velocity Factor of 82%. The minimum bend radius of this cable is 2.50 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? Please Note: Also available is our direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ and DXE-RG6UFQ-1000. This DX Engineering RG-6UQ 75-ohm Standard Quad-Shield Coaxial Cable is a Type-II PVC jacket RG-6 quad-shield cable that is RoHS compliant. Check out these low attenuation figures: 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? Order DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable.

5.0 out of 5 stars ( 1 )

$0.39

—

$219.99

DX Engineering CC4-CON Control Console and Switch Relay Unit Connectors

DX Engineering CC4-CON Control Console and Relay Unit Connectors are green 5-pin female connectors for the ends of control lines, that mate to the male connectors on these DX Engineering products: TFS4 series Transmit Four Square relay units CC-4SQR Transmit Four Square Control Consoles RFS-2 Receive Four Square relay units RFS-3 Receive Four Square relay units DVA series Dual Vertical Array relay units FVC-1 Feedline Voltage Controllers PS-2B PRO-STACK Two Antenna Phasing System CC8 Deluxe Switch Control Consoles CC8A Deluxe Switch Control Consoles They feature the convenience of a removable connector with compression screw terminals for easy connection the control wires.

Not Yet Reviewed

$20.99

DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas

DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas are high-performance antennas specifically designed for use on Top Band. You will achieve the strongest possible presence at your power level and be competitive with a 160 meter vertical monoband antenna that is only 55 feet tall! A custom-designed capacity hat system allows you to get on 160 meters with unparalleled performance. Wires and ropes have been accentuated in our product image for your viewing clarity. They are much less visible in an actual installation with minimal visual impact for such a large antenna. DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas are tunable with an impressive 40 kHz bandwidth. This means that operation on the CW DX frequencies and DX Phone frequencies are within the range of most internal tuners - no physical changes to the antenna are necessary. DX Engineering DXE-160VA-1, made with sectional aluminum tubing, is a 55-foot high Monoband Vertical Antenna system with a massive 3-inch OD base section. Included with this antenna system is a rugged, patented* stainless steel pivot fixture for ease of raising, lowering and tuning adjustments. Engineered with 6061-T8 and 6063-T832 corrosion-resistant aluminum tubing, stainless steel mounting brackets and stainless steel hardware, this antenna is very durable and attractive. Why Does This Antenna Perform So Well for Its Height? The top capacity hat is large enough that the current along the radiator is almost constant. Typical shortened verticals for this band, with smaller top-hats, have currents that vary along the length and end up producing much less signal strength. This also works in the receive mode to let you hear weaker signals, although at this frequency range dedicated receiving antennas are almost a must. See DX Engineering's full line of Receive Antennas and Array Systems. DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas feature: * High Efficiency Design * 5 kW SSB and CW rated * Unparalleled reliability * Custom designed capacity hat engineered for top performance * DX Engineering Adjustable Matching Network configures the lowest SWR * Broad 2:1 SWR bandwidth - 40 kHz - CW + DX Phone * Lowest possible take-off angle reduces domestic QRM signals * Easy tilt up and down-- Unique fold-over antenna mount features DX Engineering's patented pivoting fixture, *U.S. Patent Number 8,130,168 * High power handling and high strength, UV protected EXTREN® insulators * Ultra-rugged construction starts with 3 inch OD Aircraft Grade heavy wall tubing * Withstands steady-state winds in excess of 50 mph The optional DXE-VRW-1 Manual Winch for easy one-person raising and lowering of the antenna is available from DX Engineering. You can move the DXE-VRW-1 winch between similar antennas in a multi-antenna installation. This antenna system requires the installation of a heavy duty mounting pipe set in concrete. Specifically, 3 in. OD high strength galvanized steel tubing with 0.250 in. minimum wall thickness and 7 ft. (84 in.) minimum length, which is available from DX Engineering; part number DXE-VGMT-3CG. A customer supplied 2-1/2 in. Schedule 80 pipe that has an outside diameter of 2.875 in. is also suitable. About 36 in. of the mounting pipe should extend above the concrete. Depth of the mounting hole and amount of concrete is dependent on local soil type, condition and antenna guying. THUNDERBOLT® Vertical Antennas require a good ground radial system. We recommend a minimum of 32 radials, 65 ft. long, but more radials that are all longer will be more efficient for better signals. Note: For additional information, please look at the files under the "Documentation" tab. Do you want a great Top Band signal? If so, then try one of these DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas!

5.0 out of 5 stars ( 2 )

$1,664.97