Availability
Amplifiers
4O3A Power Genius XL HF/6M SO2R Amplifiers
4O3A Power Genius XL HF/6M SO2R Amplifiers are solid-state amplifiers capable of delivering 1500W+ output across the 160-6M amateur bands, engineered for high-performance amateur radio use. The PGXL uses dual NXP MRF1K50H LDMOS transistors, each rated for 1.5 kW, providing high headroom, low IMD, and clean signal output. It is the only amplifier with true SO2R capability, offering 70 dB isolation between two inputs. The integrated MEffA™ algorithm dynamically adjusts DC voltage for optimal efficiency. Additional features include fast SWR protection, advanced thermal management, and seamless integration with FlexRadio systems via SmartSDR. They also support third-party radios through Ethernet, RS232, CI-V, and BCD interfaces.
( 3 )
$6,184.49
—
$6,509.99
ACOM 1200S Solid State HF + 6 Meter Amplifiers
ACOM 1200S Solid State HF + 6 Meter Amplifiers cover the amateur bands from 1.8 through 54MHz. They provide 1000W output power (PEP or continuous carrier) with less than 50W of drive on 240VAC (max. 500W out on 25W RF input on 120VAC). All operational conditions are visible on a multi-function high-resolution color display. Note: To install your own power plug, order AOM-1200S (you remove the European plug) For a 120 Volt plug (NEMA 5-15P), order AOM-1200S-120 (500 watts) For a 240 Volt plug (NEMA 6-15P), order AOM-1200S-240 (1,000 watts) All part numbers include a power cable. Features include: * Five-inch (5 in.) (108x65mm) high resolution color display, 800x480 pixels and 24-bit color * Final stage uses rugged LDMOS transistor - BLF188XR or equivalent. * Compatible with all transceiver models available on the market - does not need any special signals: "ground on transmit" (PTT out) and typically less than 50W of RF drive power is sufficient for full power on 240VAC; a maximum of 25W input on 120VAC. * Broadband input circuit provides a perfect transceiver load with SWR below 1.2:1 (typically 1.1:1), with no amplifier tuning, throughout the frequency range 1.8 to 54MHz * The overall operation of ACOM 1200S is extremely simplified: the screen menus are intuitive and easy to follow * Optional automatic control – when connected to a transceiver with a CAT interface, the amplifier monitors constantly, follows the operating frequency, and changes the bands accordingly * If NOT CONNECTED with CAT interface, the amplifier monitors the RF input with a built-in frequency counter and automatically switches bands * Remotely controlled by RS232 interface * Protects itself during operation due to continuous protection circuits in all modes * The user can monitor more than 10 parameters * Easy maintenance – detailed data (55 parameters) about each of the last 28 protection trips is stored in the amplifier's nonvolatile memory * Convenient field operation: extremely compact and lightweight construction, extended mains voltage range (93V to 265V), limited inrush current and Power Factor Correction (PFC) – all significant parameters in operation from unstable mains, generators etc. features achieved thanks to the built-in switching mode power supply (SMPS) a) Rated output power: 1000W plus/minus 0.5dB, PEP or continuous carrier (1200W PEP max.). b) Intermodulation distortions (IMD3): better than 30dB below the rated PEP output. c) Harmonic and parasitic emissions output suppression: better than 60dB (65dB typically). d) Input and output impedances: nominal value: 50 Ohm unbalanced, UHF (SO-239) type connectors; * Input circuit: broadband, SWR below 1.2:1 (1.1:1 typically); 1.8 – 54 MHz continuous range without retuning or switching * Admissible SWR at the output load (the antenna): up to 3:1 with proportional power reduction and up to 1.5:1 for full output power e) RF power gain: 13dB plus minus 1dB f) Automatic AC voltage Input Handling: 93 to 265VAC (no internal wiring change needed) g) AC Input power consumption at full output power: 2000 VA or less with a power factor of 0.95 or higher h) AC mains power consumption in Low Energy (waiting) mode: less than 1VA i) Complies with EU safety regulations and electromagnetic compatibility standards, as well as with the US Federal Communications Commission (FCC) rules j) Environmental * Temperature range: -10 C to +40 C (14 F to 104 F) * Relative air humidity: up to 95 percent at 35 C (95 F) k) Dimensions and weight: (D x W x H) 418 x 372 x 162 mm (16.46 x 14.65 x 6.38 In); 14.5 kg (31.97 lbs.) Supplied with: - A power cord - A manual with a CE declaration of compliance; - Two 10A fuses for operation on 200-240VAC or 100-120VAC mains. These amplifiers offer fully automatic operation and superior solid state performance. To upgrade your station, order ACOM 1200S Solid State HF + 6 Meter Amplifiers from DX Engineering.
( 29 )
$4,750.99
Toptek Communications PA-350V VHF 135-165 MHz 350W Power Amplifiers
Toptek Communications PA-350V VHF 135-165 MHz 350W Power Amplifiers are advanced and versatile high-power linear amplifiers designed for Amateur Radio 2 Meter FM, SSB and CW operations and Commercial VHF. A large, easy-to-read green backlit Alphanumeric LCD provides simultaneous digital input power, output power, SWR readings. Front panel button actions and specialized, user-defined function readouts and menu selections are displayed, including incremental 100, 200, 300 and 350W power output settings. This VHF amplifier* delivers approximately 300 watts output with only 5 watts input from an HT or 350 watts maximum output with a VHF mobile. The PA-350V has two selectable input ranges, Low 15W max and High 30W max, achieving 350 watts output with either 10 watts input or 15 to 25 watts input, to accommodate almost any VHF transceiver. Multiple protection circuits, a Receive Low Noise Amplifier (LNA) with bandpass filter, RF sense or PTT keying (required for SSB/CW) and thermostatically controlled fans are some of the great features of this top-of-the-line Toptek amplifier. True 50 ohm Type-N RF connectors maintain the highest efficiency to the feedline and antenna. NOT compatible with DMR and P25 modes NOTE: Rear panel accessory jack (4-pin mini-DIN) is provided for the accessory REMOTE Control Panel, TEK-REMOTE. *Requires 13.8 VDC @ 50A max. (External power supply not included).
( 18 )
$879.99
On Sale
ICOM IC-PW2 HF/50 MHz, ALL Band 1kW Linear Amplifiers
The ICOM IC-PW2 HF/50 MHz ALL Band 1 kW Linear Amplifier is a high performance, multi-function linear amplifier and is considered one of the key pieces of equipment for keen competition in DX hunting and contesting. Featuring high power and full duty cycle operation, the IC-PW2 uses new 65V LDMOS power transistors (MRFX1K80HR5) and a high-efficiency power supply to achieve a full 1kW output with a 200VAC Input. The IC-PW2 instantly operates at full power once turned on. Use the IC-PW2 for long contest hours or full-duty FT8 operation. Experience linearity and clean transmission with Digital Pre-Distortion (DPD) Technology with IC-7610. This technology corrects the signal distortion from the IC-PW2, by applying inverse distortion to the output signal from the IC-7610 exciter in advance
( 5 )
$5,499.95
$5,398.95
ACOM 2020S Solid-State 1.8-54 MHz Linear Amplifiers
ACOM 2020S Solid-State 1.8-54 MHz Linear Amplifiers are state-of-the-art 1500W Solid State linear amplifiers that deliver maximum legal power in all modes and operate in all Amateur Radio HF bands from 160 through 6 meters. This amplifier is extremely operator-friendly with a remote console unit (RCU) that features a high-resolution color touch screen. The 2020S amplifier is transceiver-independent, meaning that it is compatible with all transceiver models. With no need for special signals, only ground on transmit and RF drive power, any transceiver may be used. The 2020S monitors the input signal frequency with its built-in frequency counter and automatically switches bands when there is no transceiver frequency interface cable. However, when interfaced with a transceiver with CAT, COM or CI-V capability, the 2020S tracks the transceiver operating frequency and automatically changes bands accordingly. The Acom 2020S supports direct Remote Control via the Internet with an integrated web interface and built-in Ethernet RJ45 LAN port or Wi-Fi adapter. The Acom 2020S amplifier employs two powerful modules in a power splitting/combining technique that has been time-proven in high-power commercial applications to provide sufficient output headroom. The input and output ports are isolated from each other, reducing intermodulation and improving resistance to self-excited oscillation and reliability. A broadband input circuit provides a perfect transceiver load with SWR below 1.2 without re-tuning throughout the entire frequency range from 1.8 to 54 MHz. The two final PA stages use a rugged MRFX1K80HR5 or equivalent LDMOS transistor. The 2020S features built-in intelligence that continuously monitors system health and protection circuits in all modes. Also, the operator can monitor eleven different parameters of amplifier operation. Detailed fault data is stored in the amplifier's memory and shows up to 55 parameters for each of the last 28 hard-fault protection trips. Compact and lightweight construction with a built-in switching-mode power supply that operates within a power mains voltage range of 200-240 VAC, ±10% (180-264 VAC limiting values), with no internal switch over. The consumed current is purely sinusoidal, power factor corrected and in-rush current limited, which makes the operation of this amplifier from unstable AC mains and generators easy and trouble-free.
( 8 )
$7,934.99
ACOM 1500 HF + 6 Meter Linear Amplifiers
ACOM 1500 HF + 6 Meter Linear Amplifiers are user-friendly and look after themselves. They are designed to safely withstand up to 300 watts of reflected power and up to 100 milliseconds duration of drive spikes. These amplifiers also continue to function with "soft" AC mains and will deliver more than half power at only 85 percent of nominal mains voltage. They can withstand voltage drops for up to 10 milliseconds and can tolerate 15 percent mains voltage spikes. This level of tolerance is especially important on Field Day, during DXpeditions, and at portable operating events where emergency power is relied upon. Please see the SPECIAL Note, below. The True Resistance Indicator (TRI) is a powerful tuning aid that helps the operator to quickly and precisely match the antenna impedance to the optimum tube load impedance. The auto-operate function (when enabled) maintains the amplifier in the OPERATE mode, thus avoiding unnecessary manual operations. Your ACOM amplifier will enable you to change antennas virtually instantaneously and allow you to use your antennas over wider frequency ranges. Broadband input matching presents a very good load to the transceiver over the entire spectrum of 1.8-54 MHz. These amplifiers produce virtually-silent QSK. The input bypassing and vacuum antenna relays are virtually silent even in the CW QSK mode; thanks to specially designed mounting hardware. ACOM 1500 amplifiers utilize a single 4CX1000A ceramic and metal radial-beam tetrode vacuum tube with plate dissipation of 1,000 watts. Tube protection includes permanent monitoring and automatic protection of plate and grid voltages and currents, as well as the exhaust air temperature. These pieces of data are essential to indicate 4CX1000A operating conditions. All ACOM 1500 amplifier status indications are explained via detailed text displayed on the dot matrix, high brightness, vacuum fluorescent display (VFD). LED indicators are provided for Power, Operate mode, Attenuation-on, Transmit, Selected antenna output, and ON/OFF conditions. * Frequency Coverage: 1.8-54 MHz * Power Output: 1,500W PEP, 1,200W continuous carrier; for continuous carrier transmissions longer than 15 minutes the external auxiliary fan must be installed * Intermodulation Distortion: Better than 35dB below PEP rated output * Hum and noise: Better than 40dB below rated output * Harmonic Output Suppression: 1.8-21.5 MHz; 50dB below rated output, 24-54 MHz; 66dB below rated output * Input and Output Impedance: Nominal values: 50 Ohm unbalanced output; Input circuit: broadband, VSWR less than 1.3:1, 1.8-54 MHz (no tuning, no switching); Bypass path: VSWR less than 1.1:1, 1.8-54 MHz continuously * RF Gain: 13dB typically, frequency response less than 1dB (60-85 W drive power for rated output) * Primary Power: 100-264V (100, 110,120, 200, 210, 220, 230 and 240V nominal taps), 50-60Hz, single phase, 3500VA consumption at rated output * SPECIAL Note: Order part number AOM-1500 to wire the AC plug yourself; order part number AOM-1000-240 for pre-wired 240 volt operation * Complies with CE safety and electromagnetic compatibility requirements as well as FCC-regulations * Size: 16.6 x 14 x 7.7 in. * Weight 58.4 lbs. * Operating environments: Temperature range 0 to 50 degrees C, Humidity up to 95 percent at 35 C * Altitude: up to 3,000m (10,000ft) above sea level without output deterioration Note: For additional information, please look at the files under the "Documentation" tab. Why not allow yourself to enjoy the finest amplifier? Order one of your own ACOM 1500 HF + 6 Meter Legal Limit Linear Amplifiers from DX Engineering and give your signal a nice boost! Note: During and after your amplifier's warranty period, DX Engineering can direct you to the appropriate location for repairs for ACOM amplifiers. That facility will charge a repair fee for services outside the warranty period.
( 14 )
$5,122.99
ACOM 700S Solid State 1.8-54 MHz Linear Amplifiers
ACOM 700S Solid State 1.8-54 MHz Linear Amplifiers are state-of-the art amplifiers that cover all amateur bands from 160 through 6 Meters. These amps provide 700 W output power (PEP SSB or CW modes). Working parameters of the amplifier are indicated on a multi-function, high-resolution 5 inch color display. Amplifier control is accomplished with only six buttons on the front panel or directly by CAT interface from the transceiver or remotely by RS232 interface. ACOM 700S amplifiers are compatible with all transceiver models available on the market. The broadband input matches to the transceiver with low SWR over the entire range of 1.8-54 MHz. Full output operation only requires a maximum of 40 watts drive and the typical "ground on transmit" (PTT) keying with no special signals required. The overall operation of ACOM 700S amplifiers is extremely simplified. Screen menus are intuitive and easy to follow and no special skill is required from the operator when changing frequency bands. The amplifier monitors the frequency of the input signal through the built-in frequency counter and automatically switches bands. A band data or CAT interface connection from the transceiver is NOT required for automatic band changing. These amplifiers take care of themselves during operation, due to the continuously-working protection circuits in all modes. The operator can digitally monitor more than 10 parameters concerning the working conditions of the amplifier. Detailed data (55 parameters) about each of the last 28 hard-fault protection trips is stored in the amplifier's nonvolatile memory. ACOM 700S amplifiers are perfect for DXpeditions and field operation. They are extremely compact and employ light-weight construction thanks to the built-in switching-mode power supply. They operate on an extended mains voltage range** (100-120VAC and 200-240VAC) by changing only the main fuses - no internal switching is required. Please read the SPECIAL NOTE at the end of the specifications. ACOM 700S Solid State HF/6-Meter Amplifiers are among the finest and most modern linear amplifiers available anywhere in the world. These outstanding amplifiers are available from DX Engineering! ACOM 700S Solid State Linear Amplifier Specifications: * Rated output power: 700W PEP SSB or CW * Intermodulation distortion (IMD3): Better than 31dB below rated PEP output * Harmonic and parasitic emissions suppression: Better than 60dB (65dB typical) * Input and output impedances: SO-239 UHF female connectors; 50 ohm unbalanced output; * Input circuit: broadband, SWR below 1.2:1, 1.8 to 54 MHz continuous without retuning or switching * RF power gain: 14dB +/- 1dB * Complies with US Federal Communications Commission (FCC) rules and the EU safety regulations and electromagnetic compatibility standards * Temperature range: 14 degrees F to 104 F (-10 C to +40 C) * Relative humidity: up to 95 percent at 95 F (35 C) * Dimensions (WHD): 12.8 x 5.6 x 14.2 in. (326 x 143x 365 mm) * Weight: 26 lbs. (11.8 kg) **Mains supply voltage: 100-240V, 50-60 Hz, single phase, automatic switching supply; no internal change required for either mains voltage; European style 5x20mm fuses rated for 250VAC for correspond mains: 10A fuses for operation from 200-240VAC, 16À fuses for operation from 100-120VAC. SPECIAL NOTE: Due to power efficiency the use of 240 Vac service is highly recommended. -AOM-700S-240 is pre-wired with NEMA 6-15P USA plug for 240 volt operation. - AOM-700S-120 is pre-wired with NEMA 5-15P for 120 volt operation. - AOM-700S has NO PLUG; order this model to wire your own AC plug for either voltage. * AC load: 1,350VA or less with a power factor of 0.95 or higher * AC load in Low Energy (standby) mode: less than 1VA For additional information, please check the "Documentation" tab.
( 35 )
$4,367.99
ACOM 1010 HF Linear Amplifiers
ACOM 1010 HF Linear Amplifiers cover all bands from 1.8 through 29.7 MHz. They provide over 700 W PEP output (or 500 W continuous-modes) with less than 60 watts of drive and operate without special transceiver signaling; they need only "ground on TX" and the required drive. ACOM's exclusive True Resistance Indicator (TRI); enables faster antenna changes and use over wider frequency ranges. Also, a built-in antenna selector switch with two outputs is included to provide instant choice of antennas. Antenna matching can be achieved in less than 10 seconds and at a quarter of nominal output power, which results in lower risk of interference to other stations and greater safety to the amplifier components. A single ACOM 4CX800A high-performance ceramic-metal tetrode with plate dissipation of 800 watts is used for maximum efficiency. These amplifiers are self-monitoring. They are designed to safely withstand up to 240 watts of reflected power, up to 100 milliseconds of drive spikes (RF "tails" after a PTT or KEY release), and even operator tuning errors. They are also capable of operating at more than half their designed output at only 75 percent of nominal line voltage. Because they can tolerate deep voltage drops and 15 percent line voltage spikes, they are particularly well-suited for use in portable environments, such as Field Day and DXpeditions. Importantly, a variety of system parameters are continuously monitored and available to the operator to assure safe and efficient amplifier operation. Design of the high-voltage power supply eliminates the danger of turn-on transients affecting sensitive devices connected to the same line (mains) circuit. Moreover, the amplifier can be configured to accommodate any of eight nominal line voltages between 100 and 240 V, 50 or 60 Hz. Please see the SPECIAL Note, below. ACOM 1010 specifications: * Frequency Coverage: All amateur bands in the 1.8-29.7MHz frequency range * Power Output: 700 W PEP or 500 W continuous modes. * Intermodulation Distortion: Better than 35 dB below rated output. * Hum and noise: Better than 40 dB below rated output. * Harmonic Output Suppression: Better than 50 dB below rated output. * Input and Output Impedance: Output: 50 Ohm unbalanced, SO-239 connectors; Input circuit: broadband, VSWR less than 1.3:1, 1.8-30 MHz continuously (no tuning, no switching); Bypass path: VSWR less than 1.1:1, 1.8-30 MHz continuously, 200 W maximum * RF Gain: 11dB, frequency response less than 1dB (50 to 70 W drive for rated output) * AC Power: 85-132 V/170-264 V ac (100, 110, 120, 200, 210, 220, 230 & 240 V nominal taps, plus 10 percent to minus 15 percent tolerance), 50-60 Hz, single phase, 1,200 VA * SPECIAL Note: Order part number AOM-1010 to wire your AC plug after removing European plug yourself; order part number AOM-1010-240 for pre-wired 240 volt operation (NEMA 6-15P) or part number AOM-1010-120 for pre-wired 120 volt operation (NEMA 5-15P). * Operating environments: Temperature range; 32 to 122 degrees F, Humidity; up to 95 percent at 95 degrees F, Altitude; up to 10,000 above sea level without output deterioration. * Complies with FCC-regulations as well as CE safety and electromagnetic compatibility requirements * Dimensions, (in.) 15.83 W x 12.4 D x 6.5 H * Weight: 39.7 lbs. Note: For additional information, please look at the files under the "Documentation" tab. Get one of these highly-advanced HF amplifiers for your shack. Order an ACOM 1010 HF Linear Amplifier from DX Engineering… today! Note: During and after your amplifier's warranty period, DX Engineering can direct you to the appropriate location for repairs for ACOM amplifiers. That facility will charge a repair fee for services outside the warranty period.
( 53 )
$3,376.99
RM Italy MLA300 HF Linear Amplifiers
RM Italy MLA300 HF Linear Amplifiers are broadband linear amplifiers designed for operation from 1.8 to 30 MHz (160–10 meters), delivering up to 300 watts of average output power. It supports input power levels from 1 to 15 watts, making it compatible with most modern QRP transceivers. Powered by four MACOM MRF455 transistors in two parallel push-pull AB-mode circuits, the MLA300 provides clean, reliable operation for SSB, CW, AM, FM, and digital modes.
Not Yet Reviewed
$836.99
ACOM 1000 HF + 6 Meter Linear Amplifiers
ACOM 1000 HF + 6 Meter Linear Amplifiers are the world's best value in an Amateur HF amplifier. These amps provide you a comfortable 1,000 watts output on all amateur bands from 160 through 6 meters. The plate-load True Resistance Indicator (TRI) is a powerful tuning aid which helps the operator to quickly and precisely match antennas. The auto-operate function (when enabled) maintains the amplifier in OPERATE mode for you, saving on manual operations. Broadband input matches to the transceiver over the entire range of 1.8-54 MHz. ACOM 1000 amplifiers are both user-friendly and look after themselves. They are designed to safely withstand up to 300 watts reflected power, drive spikes of up to 100 milliseconds duration, drive RF "tails" after a PTT or KEY release and the operator's inadvertent tuning errors. They also withstand a "soft" AC line and will deliver more than half power at only 75 percent of nominal mains voltage. They can withstand voltage drops for up to 10 milliseconds, and up to 15 percent higher line-voltage spikes. These details are all important, particularly when used at Field Day, on DXpeditions and other portable operations. Be sure to read the SPECIAL Note, below. An ACOM 4CX800A high-performance ceramic/metal tetrode with plate dissipation of 800 watts is employed. On-board processing provides permanent monitoring and protection of plate and grid voltages and currents, as well as the exhaust temperature. Text messages, 12 different parameters, and strip peak-reading PEP meter are displayed on a dot-matrix, back-lighted LCD. LED indicators are provided for OPERATE, attenuator-on, and ON/OFF conditions. Records of the amplifier internal status are stored in nonvolatile memory for the seven most-recent auto-protection trips. This information is very valuable should diagnostics be needed. The input bypassing and the vacuum antenna relays are very quiet even in CW mode due to their special mounting. This results in virtually noise-free QSK! ACOM-1000 details: * Frequency Coverage: 1.8-54 MHz * Power Output: 1,000W PEP or continuous carrier; for continuous carrier transmissions longer than 15 minutes the external auxiliary fan must be installed * Intermodulation Distortion: Better than 35dB below rated output * Hum and noise: Better than 40dB below rated output * Harmonic Output Suppression: 1.8-29.7 MHz; 50dB below rated output, 50-54 MHz; 66dB below rated output * Input and Output Impedances: Nominal values: 50 Ohm unbalanced output; Input circuit: broadband, VSWR less than 1.3:1, 1.8-54 MHz; Bypass path: VSWR less than 1.1:1, 1.8-54 MHz continuously * RF Gain: 12.5dB typically, frequency response less than 1dB (50-60W drive power for rated output) * Primary Power: 170-264V (200, 210, 220, 230 and 240V nominal taps), 50-60Hz, single phase, 2200VA consumption at rated output. 230 or 240 volts recommended for USA * SPECIAL Note: Order part number AOM-1000 to wire the AC plug and voltage selection yourself; order part number AOM-1000-240 for pre-wired 240 volt operation or part number AOM-1000-120 for pre-wired 120 volt operation * Complies with CE safety and electromagnetic compatibility requirements as well as FCC-regulations * Size: 16.6 x 14 x 7.2 in. * Weight 58.5 lbs. * Operating environments: Temperature range 32 to 122 degrees F, Humidity up to 95 percent at 95 F * Altitude: up to 3,000m (10,000 ft.) above sea level without output deterioration Note: For additional information, please look at the files under the "Documentation" tab. ACOM says that these are the "world's best value" in an Amateur HF amplifier. Order one of these ACOM 1000 HF + 6M Linear Amplifiers from DX Engineering and decide for yourself! Note: During and after your amplifier's warranty period, DX Engineering will provide service and repair for ACOM amplifiers. A repair fee will be charged for services outside the warranty period.
( 47 )
$4,364.99
ACOM 2100 HF + 6 Meter Linear Amplifiers
The ACOM 2100 is a complete and self-contained linear amplifier that covers all Amateur bands from 1.8 through 54 MHz and provides over 1500W PEP or continuous carrier output power, typically at only 40 to 55 watts drive. The 2100 utilizes a single 4CX1000A ceramic and metal radial-beam tetrode vacuum tube with plate dissipation of 1,000 watts. This manually tuned amp features many automatic functions. Tube protection includes permanent monitoring and automatic protection of plate and grid voltages and currents, as well as the exhaust air temperature, essential data that indicates the power tube operating conditions. The 2100 amplifier features virtually silent high-speed break-in CW (QSK). The input bypassing and vacuum antenna relays are virtually silent even in the CW QSK mode; thanks to specially designed mounting hardware. The 2100 is designed to safely withstand up to 400 watts of reflected power and up to 100 milliseconds duration of drive spikes. Additionally, these amplifiers continue to function with "soft" AC mains and will deliver more than half power at only 85 percent of nominal mains voltage. They can withstand voltage drops for up to 10 milliseconds and can tolerate 15 percent mains voltage spikes; especially important on Field Day, during DXpeditions, and at portable operating events where emergency power is relied upon. Be sure to read the SPECIAL Note, below. The True Resistance Indicator (TRI) is a powerful tuning aid that helps the operator to quickly and precisely match the antenna impedance to the optimum tube load impedance. The auto-operate function (when enabled) maintains the amplifier in the OPERATE mode, thus avoiding unnecessary manual operations. Broadband input matching presents a very good load to the transceiver over the entire spectrum of 1.8-54 MHz. Your 2100 will enable you to change between three antennas virtually instantaneously and allow you to use your antennas over wider frequency ranges. All ACOM 2100 amplifier status indications are explained via detailed text displayed on the high brightness OLED display. LED indicators are also provided for Power, Operate Mode, Attenuation-on, Transmit and Selected Antenna output. ACOM 2100 Features and specifications: * Frequency Coverage: 1.8-54 MHz * Power Output: 1,500W PEP, 1,500W continuous carrier; for continuous carrier transmissions longer than 15 minutes the external auxiliary fan must be installed * Intermodulation Distortion: Better than 32dB below PEP rated output * Hum and noise: Better than 40dB below rated output * Harmonic Output Suppression: 1.8-29.7 MHz; 50dB below rated output, 50-54 MHz; 66dB below rated output * Input and Output Impedance: Nominal values: 50 Ohm unbalanced output; Input circuit: broadband, VSWR less than 1.3:1, 1.8-54 MHz (no tuning, no switching); Bypass path: VSWR less than 1.1:1, 1.8-54 MHz continuously * RF Gain: 13.5dB typically, frequency response less than 1dB (40-55 W drive power for 1,500 watts output) * Primary Power: 100-264V (100, 110,120, 200, 210, 220, 230 and 240V nominal taps), 50-60Hz, single phase, 3500VA consumption at rated output * Complies with CE safety and electromagnetic compatibility requirements as well as FCC-regulations * Size: 17.5 x 14.7 x 8.0 in. * Weight 64.6 lbs. * Operating environments: Temperature range 0 to 50 degrees C, Humidity up to 95 percent at 35 C * Altitude: up to 3,000m (10,000ft) above sea level without output deterioration Why not allow yourself to enjoy the finest amplifier? Order your own ACOM 2100 HF + 6 Meter Linear Amplifier from DX Engineering and give your signal a nice boost! Note: During and after your amplifier's warranty period, DX Engineering can direct you to the appropriate location for repairs for ACOM amplifiers. That facility will charge a repair fee for services outside the warranty period.
( 31 )
$5,687.98
Yaesu SPA-1 FTX-1 Series 100W HF/VHF/UHF Amplifiers
Yaesu SPA-1 FTX-1 Series 100W HF/VHF/UHF Amplifiers are designed as an optional accessory for the Yaesu FTX-1 Field Transceiver. By easily connecting the SPA-1 to the rear of your FTX-1 Field Head, you instantly gain a significant power boost, achieving 100W output on the HF bands and 50W output on the 144MHz (2-meter) and 430MHz (70cm) VHF/UHF bands. This increased power dramatically improves your transmission range and signal strength, ensuring more effective communication from your base station. Originally included with the FTX-1 Optima, the SPA-1 is now available separately. It allows FTX-1 Field owners to transform their transceiver into a powerful portable or base station, offering the ultimate flexibility for both field and home operations.
( 2 )
$709.99
RM ITALY BLA600 Solid State Amplifiers
RM ITALY BLA600 Solid State Amplifiers are wideband, compact, automatic linear amplifiers for 160 through 6 meters; 1.8 to 54 MHz. Low input drive requirements (20 to 25W on 80-10 meters, 30-40W for 500W on 160m and 6m) make these amplifiers THE perfect transceiver companion! RM ITALY BLA600 amplifiers are fully automatic 500W solid-state linear amplifiers suitable for seamless integration with all modern transceivers. They utilize the rugged NXP / Freescale MRF6VP5600H 50V power MOSFET for high power and high reliability. These amplifiers are capable of all modern modulation modes. BLA600 amplifiers are fully automatic, featuring instant RF frequency-reading for band changes and fast, reliable and silent PIN diode TX-RX switching, making them ideal for CW QSK operation (separately purchased transceiver to amplifier PTT keying cable is required.) BLA600 amps have three (3) antenna outputs that are easily configurable on a per-band basis as per the user's requirements. Their RF deck is supplied by a heavy-duty linear power supply, with 240 volt AC input* (115-120 or 230 VAC capable) and utilizes an efficient active bridge rectifier with very high-grade filter capacitors to provide the PA devices with a very low noise and robust 50V DC. The amplifier's RF deck has a large heat spreader and copper heat sink which provides a very efficient cooling system. There are separate fans for the RF deck and LPF board / power supply for high duty cycle operation. Internally, all modules are mounted in a very robust and well-screened enclosure. BLA600 amplifiers feature Dual MCU control and an extensive array of protection circuits that look after the amplifier with rapid reaction time. VSWR, I/P Power, I/P Frequency, Three Temperature sensors; Transistor / Heat sink and PSU, Drain voltage / Drain current and HV PIN supply are all continuously monitored. Some thumbnail details: * Employs Freescale MRFE6VP5600 Power FETs * Drive requirements: 20-25W for 500W on 80-10m; 30-40W for 500W on 160m and 6m * Input drive from 1W to maximum of 40W (1 to 25W w/reduced output) * Power Gain: Typical 14dB +/- 1dB (80-10m) * Solid 500W Output on all modes * Dual MCU Control * Fast PIN Diode RX-TX TX-RX switching enables full QSK operation * 2x16 LCD screen for Amplifier Status * Two Separate LED displays; one for power and one for antenna VSWR * Three antenna output connectors, user-configurable * Dual large-diameter MCU controlled multispeed fans for efficient cooling * 1,200W Linear Power Supply- Highly filtered and regulated * Weight: 21.5kg (47.4 lbs.) * Quiet, 240 VAC operation **Requires a user supplied NEMA 6-15P to IEC 320-C13 Cord. (Internally resettable for 230 or 120 VAC input on jumper board under rear access panel secured with T10 torx screws) * AC Input Fuse: 5 x 20mm F LBC 250V; Fast Blow, 240 VAC 5A (included); or 230 VAC 6A (optional) or 115-120 VAC 10A (optional, with NEMA 5-15P to IEC 320-C13 15A Cord.) WARNING: Amplifier is set from the factory for 240VAC operation. Do not use a low amperage PC power supply AC cord. An IEC C-13 14AWG 15A cord is required with NEMA 6-15P for 240VAC or NEMA 5-15P for 120VAC after internal jumpers and fuse have been changed. If your HF transceiver can be set for 20 to 40 watts output, then you will be sending 500 watts to the antenna on ALL bands 160 through 6 meters using this amplifier. The real beauty is that it all happens fully automatically! There is no tuning and no band switching! Give your signal a nice boost. Order the RM ITALY BLA600 Solid State Amplifier from DX Engineering!
( 14 )
$3,086.99
Penta Labs RF Vacuum Tubes
Penta Laboratories was founded in 1951 and is a world-class manufacturer and distributor of a wide range of vacuum tubes for a variety of industries. Penta's commitment to excellence begins with design and follows each product all the way through distribution. Penta Labs matched vacuum tubes go through rigorous test procedures to enhance performance during their operation. Each Penta Labs vacuum tube is burned in for a minimum of 48 hours dissipating full power with filament, plate and screen voltages that are normally used in amplifier applications. All of this ensures that the various electrical parameters have stabilized and the matching of each vacuum tube will not drift during its lifetime. Penta Labs power tubes are matched within a 5% variation on all parameters. This is a process of eliminating tubes that test with bad values, rejecting those outside limits of design. Each passing vacuum tube is then tested on a fleet of WT-100A original RCA production testers for plate current, screen current and transconductance (gm). We also check for grid current and leakage between elements. When you receive single and matched vacuum tubes from Penta Labs, you can rest assured that you are receiving a product that has been thoroughly tested and will perform at levels unsurpassed in the industry. DX Engineering offers a selection of Penta Labs single and matched sets of RF vacuum tubes and ceramic vacuum tubes for your electronics project or repair. Order yours today!
( 88 )
$56.99
—
$2,098.99
Toptek Communications PA-150U UHF 430-470MHz 150W RF Power Amplifiers
Toptek Communications PA-150U UHF 430-470MHz 150W RF Power Amplifiers are very capable, efficient 2-stage UHF linear amplifiers for FM, SSB, CW and Digital modes of operation. This amplifier provides over 150 watts of output with only 2 to 5 watts input drive, dependent upon UHF frequency from 430 to 470 MHz, with slightly lower output from 460 to 470 MHz. An attractive and useful front panel with a digital multi-meter and push-button controls, and a heatsink chassis with cooling fans, makes this amp perfect for commercial or Amateur UHF operations. PA-150U UHF Amplifiers have these important features: - Front panel digital metering of input and output power and SWR - Automatic Fault protection for SWR over 2:1 - Built-in low-noise receive preamplifier, with band pass filtering; nominal 10 dB gain - PTT Input for proper operation in SSB, CW and Digital Modes - RF sense keying for FM mode (PTT connection not required for FM) - Mode switch for automatic SSB delay and peak power metering - Settable FM mode power output: LOW, Medium 100W and High 150W steps - Ultimate SSB maximum 5W PEP input, 170W PEP output (maximum peak power) - Amplifier standby maximum bypass power: 50W - Type N female connectors, 50 ohm Input and Output - Permanently attached 24 in. (60cm) DC power cable, unterminated - DC Input: 13.8 Vdc @ 30A maximum at full output 150W (10.5 to 14.8 Vdc operational range) - Dimensions (WHD): 7.25 x 3.50 x 12.52 in. (184 x 89 x 304mm) - Weight: 6.6 lbs. (3.0 kg) - NOT compatible with DMR and P25 modes NOTE: Rear panel accessory jack (4-pin mini-DIN) is provided for the accessory REMOTE Control Panel, TEK-REMOTE.
( 3 )
$739.99
DX Engineering KD9SV Keying Relay
DX Engineering KD9SV Keying Relay, DXE-SV-KR, is a high speed Solid State interface designed to protect transceiver keying circuits from potential damage by amplifier relays. Transceiver low voltage keying circuits handle only a few milliamperes (mA), but some "modern" amplifier relays require over 150 mA at 12 VDC. High voltage and high current amplifier keying relays were common in amplifiers made between 1950 and 1975. The DXE-SV-KR can safely key almost all DC amplifier relays, including older relays and keying inputs that operate at high voltage, typically -100 VDC or +110 VDC. Inspired by the original KD9SV Keying Relay, the DXE-SV-KR quickly and silently does the work of a 6-pin normally open (N.O.) Double Pole Single Throw (DPST) relay. It provides two completely isolated ground independent PTT Outputs, each capable of handling up to +/- 450VDC at up to 500mA. The DXE-SV-KR optically isolated PTT Input only requires 2mA at 13.8VDC to key, so it is safe for any transceiver's amplifier keying circuit or any other 'ground-on- transmit' PTT keying accessory. Built in a convenient enclosure with RCA phono jacks, the DXE-SV-KR is also QSK capable for keying any amplifier that supports high speed CW keying, typically a Solid State amplifier (or specially equipped tube amplifier) with a high-speed circuit for "Key In" PTT. The DXE-SV-KR may also be used to isolate a straight key or a Solid State electronic keyer connection to any CW key input. It can provide crucial protection and safety on high voltage CW key jacks and circuits common on old tube-type transmitters and transceivers. The DXE-SV-KR Keying Relay's high speed capability also provides relay debouncing, or it can be used as a remote high-voltage DC switch. The DXE-SV-KR operates on 13.8VDC to an input 2.1mm DC connector. A mating 2.1mm plug and wire are included. The DXE-SV-KR features standard RCA phono female connectors for ground-on-transmit Input and Output ports and is compatible with almost every transceiver or transmitter and amplifier combination. RCA phono patch cables are sold separately. The DX Engineering KD9SV Keying Relay is an uncomplicated way to ensure that your sensitive transceiver or electronic keying circuit is isolated and protected. CAUTION: DO NOT connect the DXE-SV-KR to AC voltage relays in antique amplifiers, typically 110VAC. See instructions. Except for AC switching, the DXE-SV-KR replaces the Ameritron ARB-704.
( 5 )
$109.99
ACOM 1003 HF + 6 meter Linear Amplifiers
ACOM 1003 HF + 6 meter Linear Amplifiers are self-contained, full-featured units that cover all amateur bands from 1.8 MHz to 54 MHz. With less than 80 watts input, they deliver 1000 watts PEP output or 900 W continuous carrier using a single ceramic/metal power triode 3CX800A7. ACOM 1003 models have two new front panel relay switches, one to select from three antenna outputs and another to quickly engage and disengage an input attenuator for rapid tuning without transceiver adjustment. A multitude of advanced features in this compact and affordable amplifier validates its admirable design. ACOM 1003 Amplifiers are available from DX Engineering in three versions: •AOM-1003-240 Tested with a pre-installed NEMA 6-15P for 240 VAC at 8.5A (10A fuses) •AOM-1003-120 Tested with a pre-installed NEMA 5-15P for 120 VAC at 15A+ (20A fuses) •AOM-1003 Install your own plug, reset voltage taps internally, 10A fuses supplied The ACOM1003 HF+6M Linear Amplifier is amazingly easy to operate! •True Resistance Indicator (TRI) bar scale meter: Simplifies accurate adjustment of plate-load impedance controls. •Two-line OLED Display: Provides a peak power bar graph meter, 18 unique operational parameters and text status messages. •External Tuner Not Needed: For antenna SWR up to 3:1, even at 1000 W output. •Front-panel Input Attenuator: Instantly reduces input power when tuning, eliminating the need for transceiver power adjustments. •Silent HF Reed Relay: Enables Fast T/R switching for QSK CW. Additional features and protection: •Operator selectable class AB2 mode for best linearity in SSB mode or class B for reduced plate dissipation in continuous digital modes. •Operator selectable Full 100% or 50% power output with no efficiency deterioration. •Auto controlled air flow tube cooling. •Continuous monitoring of amplifier parameters and tube protection. •Able to monitor 18 operator-selectable amplifier parameters on the display. •Unique ACOM protection for the bands switch. •Factory tuned input lowpass filters for best linearity and input SWR less than 1.3 in each amateur radio band. -OLED comment display – Two-line OLED display with peak-reading forward-output power bar graph and 18 operator-selectable amplifier parameters on the display. -Three antenna outputs – Three antenna outputs are selectable by a push-button on the front panel. -Less noise in the shack – HF antenna reed relay for a virtually silent, QSK compatible CW operation. -Transceiver-independent – The amplifier operates without special signals from the transceiver - "Ground on TX" (PTT) and 50-80 W RF drive power are sufficient. -Single tube operation – Uses a single ceramic/metal power triode 3CX800A7 in cathode driven, grounded grid configuration. -Tube protection – Continuous monitoring of amplifier parameters and tube protection. -Output RF arc protection – Original ACOM HF arc protection at the output, or at the antenna. -Power supply – Single phase mains power, 90-132 / 180-264 VAC at 50-60 Hz, power consumption at rated output – up to 2000 VA @ 240 VAC. Internal taps for 8 nominal AC mains voltages: 100, 110, 120, 200, 210, 220, 230 & 240VAC, ±10% tolerance), 50-60 Hz, single phase. -Easy maintenance – Non-volatile memory with SIGNATURE records eight of the most recent Serious (Hard Fault) Protection events. -Documentation – The User's Manual is available as a PDF file only. The latest version is available under the Download tab (see above). ACOM creates and distributes its documentation in ENGLISH language only.
( 2 )
$4,899.99
RM ITALY LA 250 Series VHF Linear Amplifiers
RM ITALY LA 250 Series VHF linear amplifiers are wideband, compact amplifiers covering 140 to 150 MHz. Available in two models, the only difference is that the LA 250 V includes a pair of cooling fans while the LA 250 does not. These high-power 2-meter amplifiers will provide up to 200 watts FM output. *** Note: Amplifier Color may vary. NOT compatible with DMR and P25 modes LA 250 Series details: * Frequency range: 140 to 150 MHz continuous * Input drive: 1 to 15 watt (maximum). Typically 10 to 12 watts in for 200 watts out * FM output power: 200-watt maximum * Modulation types: SSB, CW, AM, FM, data (switch selectable AM/FM or SSB) * PTT input or RF sense operation * LCD amplifier status screen: -- Input power -- Output power -- SWR -- Heatsink temperature * Internal low-pass filter * Self protection: Reverse polarity, high temperature, load VSWR, and excessive input power * Input VSWR: 1.1 to 1.5:1 * Output VSWR limit: 2.8:1 * SWR power foldback * Optionally cooled version with multispeed fans (LA 250 V) * Supply voltage: 12 to 14Vdc * Maximum DC current: 30A * Internal power fuses: three 10-amp (5x20mm Fast Blow) * Maximum bypass power (amplifier off): 50 watt * Power transistors: 4x Mitsubishi RD70HVF1 Important: Depending upon SWR and input voltage, 200 watts maximum output is typical with 10 to 12 watts input; 15 watts is the maximum input permissible for a low distortion signal. Protection circuits will take the amplifier offline (fault) at about 18 to 20 watts. Running amplifier output at 170 to 180 watts produces a more intelligible signal at virtually the same received level. Note: For additional information, please look at the files under the "Documentation" tab. These RM ITALY LA 250 Series VHF linear amplifiers are perfect for mobile use! You may also want to use them with a 5 watt portable radio or low-power base radio. Order from DX Engineering to give your 2 meter operations a boost!
( 14 )
$679.99
—
$729.99
Toptek Communications PA-80V-U Dual Band FM VHF/UHF Power Amplifiers
Toptek Communications PA-80V-U Dual Band FM VHF/UHF Power Amplifiers are attractive and flexible units intended for analog use with dual band handheld FM transceivers (HT), for Amateur 2M/70cm and VHF-UHF Safety, Business, Marine and Commercial applications. The PA80V-U operates over the 138-174 MHz and 430-470 MHz ranges with a nominal maximum power output of 80 watts on both bands. Typically, full output is achieved with 5 watts input from the transceiver. At a minimum input of 1 watt (maximum 10 watts), the amplifier automatically recognizes the transmitting frequency, switches to the appropriate band and signal path and keys the PA. The output power level can be set independently for VHF and UHF, preset to one of four steps: 25W, 45W, 65W, 85W. A multi-function eight LED bar graph meter measures Power Out, indicates power level settings, SWR (when Show SWR button is depressed), and indicates High SWR, Overdrive, Over-Under Voltage, High Temperature and PA Fail. Only FM Mode is supported, not DMR. NOT compatible with DMR and P25 modes. The Receive Low Noise Amplifier (RX LNA) can be turned on or off independently from the transmit Power Amplifier (TX PA). The LNA provides about 21db on VHF and 12dB on UHF. Input and Output connectors are Type N female for the best SWR and lower losses. The PA-80V-U requires 13.8 VDC at a maximum of 13A.
( 3 )
$465.99
Toptek Communications PA-180V VHF 138-174 MHz 180W Power Amplifiers
Toptek Communications PA-180V VHF 138-174 MHz 180W Power Amplifiers are very stable Solid State VHF linear amplifiers designed for Amateur Radio 2 Meter FM, SSB and CW operations and Commercial communications. Dual MOSFET push-pull PAs provide full RF output of 180 watts with only 5 watts input, making this amplifier* useful for both handheld and compatible mobile VHF transceivers. Mode, RX preamp, SWR meter and Power Output Settings of 60, 100, 140 and 180 watts are front panel selectable. The front panel multi-color 8 LED string serves to indicate output power settings, output power, SWR and Error. A unique shroud enables the oversize fan to quietly cool this compact amplifier for safe long-term operation at full power. Multiple protection circuits, a 21dB Receive Low Noise Amplifier (LNA), RF sense or PTT keying (required for SSB/CW) and thermostatically controlled fan are some of the great features of this Toptek VHF amplifier. True 50 ohm Type-N RF connectors maintain the highest efficiency to the feedline and the antenna. NOT compatible with DMR and P25 modes. *Requires 13.8 VDC @ 30A max. (External power supply not included).
( 8 )
$449.99
RM ITALY MLA100 HF Amplifiers
RM ITALY MLA100 HF Amplifiers cover all Amateur bands, 160 through 6 meters, providing up to 100 watts output on HF and 80 watts on 6 meters with only 5 watts maximum RF input. They are the perfect choice for medium power operations with today's very capable, low power (QRP) radios, including many brands of portable and SDR transceivers. The MLA100 features PIN diodes for very fast receive-transmit-receive switching am seamless QSK CW fast break-in operation. Band selections are automatically detected and switched or may be set manually. Front panel LEDs display power output and SWR simultaneously on dual bar graphs. MLA100 amplifiers have built in protection from excessive input power, high temperature and high SWR. The MLA100 is a clean and capable standard solid state linear amplifier using two robust Mitsubishi RD1000HHF1 MOSFETs built into a massive, chassis-sized heatsink. The MLA100V is the same amplifier unit with the addition of an externally mounted fan. Both MLA100 and MLA100V HF Amplifiers require 13.8 Vdc at 20 A maximum, and feature a rear panel 20A ATC fuse and DC power quick connector. Also on the rear panel are Input and Output SO-239/UHF female RF connectors and a female RCA phono "PTT" for amplifier keying. Their chassis measure 190 x 182 x 78mm x (7.48 x 7.17 x 3.07 in.) and weigh 1.4kg (3.1 lbs.). *** Note: Amplifier Color may vary. PLEASE NOTE: This amplifier is intended to be used with a low power (QRP) transceiver that is capable of an RF output of approximately 5 watts maximum. DO NOT USE this amplifier with radios that are capable of 100 watts output. Even when output power is turned down, many 100 watt transceivers send out an instantaneous high power RF pulse that will blow out the Solid State final transistors of this amplifier. Damage to final transistors due to RF pulse and overdrive is NOT COVERED UNDER WARRANTY. It is the owner's responsibility to use this amplifier properly, with a low power radio that cannot accidently damage the amplifier. Cost of repair of amplifiers with blown finals will be charged to the customer or will be deducted from the refund of returned amplifiers with blown finals. Available exclusively in North America from DX Engineering, order your RM ITALY MLA100 HF Amplifier to bring new operational capability - and more fun - to your QRP transceiver.
( 15 )
$831.99
—
$851.99
RM ITALY VHF HT Linear Amplifiers
RM ITALY VHF HT Linear Amplifiers are broadband, compact amplifiers covering 135 to 175 MHz. Available in two models, the only difference is that the LA 144 is 4 W in and 60 W out, while the LA 145 is 4 W in and 85 W out. *** Note: Amplifier Color may vary. NOT compatible with DMR and P25 modes. RM ITALY VHF HT Linear Amplifiers details: * Modulation Types: SSB, CW, AM, FM, data (switch selectable AM/FM or SSB) * Frequency: 135 - 175 MHz * Power Supply: 12 - 14Vdc * Input Power: 0.5 - 4 Watts (maximum) * Output power: 70 Watts (LA 144), 85 Watts (LA 145) * Mode - AM-FM-SSB-CW Note: For additional information, please look at the files under the "Documentation" tab. These RM ITALY LA Series VHF HT Linear Amplifiers are perfect for mobile use with an HT! Order from DX Engineering to give your 2 meter portable radio some real power!
( 42 )
$189.99
—
$219.99
Toptek Communications PA-85V VHF Power Amplifiers
Toptek Communications PA-85V VHF Power Amplifiers are efficient and wideband capable. They offer a nominal output of 80 - 95 watts output with 3 to 5 watts input drive on any frequency from 137 to 174 MHz. An attractive and useful front panel and heatsink chassis gives these amps everything they need for commercial and Amateur VHF operations. PA-85V Amps have these important features: - Front panel power and SWR metering - Automatic Fault for high SWR over 2:1 - Built-in low-noise receive preamplifier, nominal 20 dB gain - RF sense keying for FM and PTT 3.5mm connector for SSB/CW. - Mode switch for automatic SSB delay and peak power metering - Settable FM mode power output: 25W, 45W, 65W and 90W limits - Maximum 5W input, 95W output – Amp off maximum bypass 50W. - SO-239 (UHF female) connectors - Permanently attached 24 in. (60cm) DC power cable, unterminated (tinned leads) - DC Input: 13.8 Vdc @ 13A maximum at full output 95W (10.5 to 14.8 Vdc operational range) - Dimensions (WHD):4.921 x 1.969 x 8.268 in. (125 x 50 x 210mm) - Weight: 2.5 lbs. (1.15 kg) - NOT compatible with DMR and P25 modes
( 20 )
$259.99
Toptek Communications PA-80U UHF Power Amplifiers
Toptek Communications PA-80U UHF Power Amplifiers are efficient and wideband capable for FM, SSB, CW and Digital modes of operation. They offer a nominal output of 80 watts output with 3 to 5 watts input drive on any frequency from 430 to 470 MHz. An attractive and useful front panel and heatsink chassis gives these amps everything they need for commercial and Amateur VHF operations. PA-80V Amps have these important features: - Front panel power and SWR metering - Automatic Fault for high SWR over 2:1 - Built-in low-noise receive preamplifier, nominal 20 dB gain - RF sense keying: Yes - PTT keying connector: Stereo 1/8 in. (3.5mm) female jack - Mode switch for automatic SSB delay and peak power metering - Settable power output: 4 steps from 30W to over 80W limit - Maximum 5W input, 80W output – Amp off maximum bypass 50W. - Type N female connectors - RF input and output - Permanently attached 24 in. (60cm) DC power cable, unterminated (tinned leads) - DC Input: 13.8 Vdc @ 13A maximum at full output 80W (10.5 to 14.8 Vdc operational range) - Dimensions (WHD):4.921 x 1.969 x 8.268 in. (125 x 50 x 210mm) - Weight: 2.5 lbs. (1.15 kg) - NOT compatible with DMR and P25 modes
( 16 )
$229.49
—
$269.99