Filters
2 Results Found For "75 ohm coax"
LDG Electronics AT-200ProII Automatic Antenna Tuners
There was a time when 100 watts was a lot of power. Today, more and more transceivers feature 200 watts of output. Even though many of these modern radios feature a built-in tuner, the tuners' range and features are usually quite limited. Break through those barriers with LDG Electronics AT-200ProII Automatic Antenna Tuners! They're designed for this new generation of rigs and are specifically recommended for Ten-Tec and tube radios. Many QRP operators have a small 100-150 watt amplifier for times when you need a few more S-units. The AT-200ProII tuners are ideal for this kind of operation; their minimum required power is only 5 watts, but they will handle higher power as well. The AT-200ProII tuners will handle up to 250 watts SSB or CW (75 watts RTTY, FT8) on 1.8-30 MHz, and 100 watts on 54 MHz. They feature LDG's state-of-the-art, processor-controlled Switched-L tuner. The AT-200ProII tuners will match virtually any kind of coax-fed antenna, including Yagis, dipoles, inverted Vs, slopers, loops, or just about anything. They will typically match a 10:1 SWR down to 1.5:1 in just a few seconds. You can also use the AT-200ProIIs with end-fed antennas, random wires, and antennas fed with ladder line with the optional LDG balun. Operation couldn't be simpler--while transmitting a carrier, just press the tune button. An automatic tuning cycle will begin and then end a few seconds later with the tuners set at the lowest SWR (almost instant for frequencies stored in memory). The AT-200ProII automatic memory tuners are the latest in a long line of innovative LDG Electronics tuners and will allow you to get the most out of your Kenwood, Yaesu, Ten-Tec, or ICOM radio that operates at higher power. Additional features include: * 5 to 250 watts SSB and CW (100 watts on 6M, 75 watts HF Digital, RTTY, PSK, FT8) * Easy-to-read LED bar graph display for RF power, SWR, and status * LEDs for antenna position and bypass * 4,000 memories (2,000 for each antenna) for instantaneous band changing * 2-position antenna switch with memories for four antennas on each position * Tuning time: 0.5 to 6 seconds full tune, less than 0.1 second memory tune * Built-in frequency counter for memory operation * Tunes 6 to 800 ohm loads (16 to 150 ohms on 6m), 6 to 3,600 ohms with optional 4:1 balun * Includes 6 ft. DC power cable * Power requirements: 11 to 16V DC at 750 mA max during tuning * Weighs 2 lbs. Note: For additional information, please look at the files under the "Documentation" tab. If you are running an older, high-output tube rig, a newer 200 watt rig, or have a small amplifier to give your QRP rig a boost, consider LDG Electronics AT-200ProII Automatic Antenna Tuners from DX Engineering!
( 36 )
$349.99
CG Antenna CG-3000 Remote Automatic Antenna Tuner
CG Antenna CG-3000 Remote Automatic Antenna Tuner is an affordable outdoor weatherproof tuner for long wires, verticals, dipoles and other Amateur, MARS or CAP operations between 1.6 to 30MHz. Like the well-known legacy SG-230, this tuner is primarily intended to feed wire antennas or monopoles. The antenna wire connects to the high voltage standoff insulator stud. A UHF female SO-239 connects the station coax and a ground stud may be used for a counterpoise or an earth ground. The tuner has an impedance range of 12 to 1000 ohms with a maximum power handling of 200 watts PEP in SSB mode and 40 watts for FT8 operation. The minimum required antenna length is 8 ft. (2.5m) for frequencies above 6 MHz, and at least 26 ft. (8m) for 1.8 MHz and up. With a small fiberglass pole and some wire, a good all-band antenna can be constructed within minutes. The CG-3000 Remote Automatic Antenna Tuner is automatically activated with a low power carrier. Low SWR tuning results are stored in non-volatile memory and new tuning attempts on similar frequencies are amazingly fast. The CG-3000 uses a Pi network design which has the advantage (as compared to L networks) of providing low-pass filtering to reduce spurious emissions. The tuner has a 4-pin connector on the bottom panel for the included 16 ft. Control Cable to supply the required 13.8 VDC at 2A (power supply not included). An additional control cable is not required. The solid plastic clamshell case protects the tuner in all-weather outdoor use. Attached brackets and 2.16 in. (55mm) width U-bolts and hardware are included. An optional CG Antennas CG-CTU Control Unit offers an ON/OFF power switch and a TUNE button, both with LED indicators and a 32.8 ft. (10M) control cable. The CG-CTU includes a 4-pin tuner interface and power connection for Icom transceivers. The CG-3000/CG-CTU combination works with all other transceivers with the included connector cable that serves as a power supply DC cable. CG Antennas CG-3000 Remote Automatic Antenna Tuner Specifications: Supported Bands: 160m, 80m, 40m, 30m, 20m, 17m, 15m, 12m, 10m. Max. Power [W]: 200 W Impedance Range: 12- 1000 Ohm Enclosure: Black waterproof plastic Supply Voltage: 13.8 VDC via included 16.5 ft. (5m) Control Cable Dimensions (WHD): 9.450 x 14.370 x 2.953 in. (240 x 365 x 75 mm) Weight: 2.98 lbs. (1.352 kg)
Not Yet Reviewed
$784.99