Selected Filters


Availability


2 Results Found For "Receive Array"

Part Groups

Results 1 - 2 of 2

InnovAntennas Ferrite Bead Baluns

InnovAntennas Ferrite Bead Baluns are fully assembled and ready to install, to achieve the absolute best performance from an InnovAntennas Yagi or other balanced terminal antennas. In contrast to wound baluns, ferrite bead choke baluns have the advantage of covering a wide frequency range for multiple bands. As required for most Yagi antennas from InnovAntennas with 50 ohm direct feed, ring terminals are installed on one end for the studded feedpoint connection. The other end is terminated in either Type-N or SO-239/UHF Female for the appropriate band coverage and impedance. Heat shrink filled with a UV-resistant adhesive provides a waterproof cover over the ferrite beads on the cable and the connector. Why do I need a Balun on my Yagi? Ferrite Bead Baluns offered by InnovAntennas provide very important functions of a balun, which is not well understood. For proper antenna performance, a ferrite bead balun inhibits common-mode current two important ways; A) it prevents RF flow on the outside the coax shield cable when transmitting, and B) it prevents stray RF noise picked up by the coax cable shield from entering the antenna system and affecting the receiver. What happens on the antenna without a RF choke balun? Several problems can occur. When an unbalanced feedline is connected directly to a balanced antenna with no BALUN in place, common-mode currents will run on the outside of the coaxial cable shield. The Yagi feedpoint is forced out of balance causing a skew and diminished beam antenna pattern and gain. A loss of Front-to-Back ratio (F/B) can occur, as well as detuning that affects antenna frequency, potentially causing increased SWR. In addition to the pattern distorting performance drop, radiation from the antenna feedline can cause interference to home and business electronics. The other very important benefit of using a wideband ferrite bead balun is to reduce received noise in certain situations. While the noise produced by many household products is normally at very low levels, sensitive ham radio receivers can be affected, which can prevents weak signals being heard. RF noise picked up on the coax cable shield will enter the antenna system feedpoint when no ferrite bead choke balun is installed at the feedpoint.

3.33 out of 5 stars ( 3 )

$119.99

DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes

Introducing DX Engineering "Maxi-Core® 20" Baluns and Feedline Chokes. They reduce or eliminate currents on the outside of your feedline allowing you to hear and to be heard much better. They keep more RFI/BCI out of your antenna and receiver and transfer more of your transmitted signal to the antenna for higher efficiency, the best antenna pattern and maximum performance. Signaling a new era of RF performance across the 1.8 to 54 MHz frequency range, DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes handle full-legal-power-plus and provide higher common mode impedance (CMI) across a greater frequency range than competing models and even previous DX Engineering and Comtek models. Years of R&D coupled with major advancements in test equipment and techniques combined with custom ferrite materials have allowed our engineering team to design the DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes. Maxi-Core® 20 Baluns and Chokes have high CMI across the AM Broadcast band and the HF/6M spectrum, which is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. Hear and be heard with DXE Maxi-Core® 20 Baluns and Feedline Chokes. Choose superior performance from these models: * DXE-MC20-1-1 Maxi-Core® 20 - 1:1 Current Choke Balun - For all HF-6m balanced antennas with a 50 ohm feedpoint, including resonant dipoles, loops, Yagis, beams, etc. * DXE-MC20-FC Maxi-Core® 20 - 1:1 Feedline Choke – This high CMI line isolator is perfect for use in line on 50 ohm coaxial feedlines, at the antenna, tower or shack end of the feedline. * DXE-MC20-1-1T Maxi-Core® 20 - 1:1 Current Choke Balun – This 1:1 "T" model is for force feeding antennas with a tuner. Use it at the end of ladder line of any impedance or mounted on a coax fed non-resonant antenna. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-C4-1 Maxi-Core® 20 - 4:1 Current Choke Balun is for use on antennas with a 200 ohm feedpoint and at the end of any impedance ladder line, especially on antenna systems with higher impedance. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-V4-1 Maxi-Core® 20 - 4:1 Voltage Balun is a 200 ohm to 50 ohm transformer for use on random long-wire and OCF antenna applications. This true voltage balun is intentionally designed with low CMI for antennas that need a transformer without RF choking for easier antenna tuner operation and it tolerates elevated SWR. Maxi-Core® 20 Baluns and Feedline Chokes are built into a convenient weather resistant NEMA enclosure that is mounted easily with optional brackets. They feature 1/4-20 stainless steel hardware and a high quality silver-plated PTFE dielectric SO-239 (UHF female) input connector. The SO-239 connector limits power handling to 5 kW at low SWR and reduced power at elevated SWR. These baluns and the feedline choke exhibit very low insertion loss and inherently low SWR. Optional mounting brackets are available for use on wire antennas or for verticals, Yagi and beam antennas. See the Suggested Parts tab after clicking "More Detail" on the model of interest. Combination packages that include balun or choke and mounting bracket are also available.

4.9 out of 5 stars ( 143 )

$147.99

—

$169.99

  • 1
  • Page 1 of 1