Availability
6 Results Found For "75 ohm coax"
DX Engineering AVA-3 Active Matching Units
DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.
( 6 )
$139.99
Unified Microsystems RAS-4 Receive Antenna Switch
Unified Microsystems RAS-4 Receive Antenna Switch is an outdoor capable remote relay unit that allows the operator to select up to four antennas. Receive only antennas are critical for success on the low bands. Due to the wavelengths of the low bands, these antennas cannot be rotated. Several very effective receive only antennas are mono-directional or bi-directional, including Beverage, Reversible Beverage, Beverage on the Ground (BOG), Reversible Beverage on the Ground (RBOG) and many others,. Therefore, a high quality, low noise four port receive antenna switch is required to cover all of the directions with multiple antennas. Common mode noise pick up can ruin the performance of receive antenna systems, so the RAS-4 isolates both the center conductor and shield of unselected ports. An internal bifilar ferrite choke further reduces common mode currents. This unit features female F connectors for RG6U coax with male F connectors, the standard field-serviceable coaxial cable assemblies for receive antenna systems. A very important requirement for dual feedline Reversible Beverage and RBOG antennas is provided by the RAS-4. By default, unselected ports are terminated for 75 ohms. The user can change to 50 ohm, open circuit, or center conductor-shield short by soldering wire jumpers. The RAS-4 is housed in a NEMA rated enclosure with a gasket lid. A cable gland seals the control cable entry. The internal circuit board has a conformal coating for additional protection. The RAS-4 can be mounted outdoors, with the enclosure flanges or with the included L bracket for mounting to a pole or post. The RAS-4 Receive Antenna Switch is a receive-only relay unit that cannot be used for transmitting antennas. The required in-shack control console switch is not included. The RAS-4 will work with a commercial or a simple home brewed, positive 12V One-of-Four switch. Choose from DX Engineering, EA4TX and others for manual or automated switching. Unified Microsystems RAS-4 Receive Antenna Switch Specifications Antenna Selection: 4 receive antennas to 1 main feedline Dimensions: Approx. 4.5 x 3.5 x 3.25 in. (11.4 x 8.9 x 8.3 cm), not including the bracket. Connector type: F (5 total) Unselected port termination: 75 ohm default; 50 ohm; open; shorted. Wire jumper selectable VSWR: < 1.5:1 from 100 kHz to 20 MHz Insertion loss: < 0.4dB from 100 kHz to 20 MHz Port to Port Isolation: > 45dB from 100 kHz to 20 MHz Control Cable: 3 wire plus ground (4 total conductors), Not included Switch Controller: 12 to 14 Vdc, Not included
( 2 )
$124.95
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 4 )
$249.99
DX Engineering Receive Feedline Voltage Couplers
DX Engineering FVC-1 Feedline Voltage Couplers provide an interface between control switches and voltage-controlled antenna systems. These specialized controllable bias-tee devices place 0V DC, +12V DC, -12V DC, and 12V AC output voltages onto the receive antenna feedline via the 75 ohm F connector or onto a 2-conductor control line. These FVC-1 couplers function from below 500 kHz to 30 MHz and provide four selections for switching antenna array directions or changing from one array to another. These couplers were designed for use with; the DX Engineering receive-only four-square antenna systems, reversible Beverage antenna systems, and remote switches. DX Engineering switch control consoles may be connected directly to the BCD switch control input of FVC-1 couplers. Alternatively, you may use your own 12V DC voltage switching system or 1 of 4 grounding switches to control the coupler by resetting internal jumpers. The connection of the feedline voltage couplers to any radio receive antenna input is to be made using either the standard RCA phono or the F connector. This allows for the use of readily available RF-compatible RCA phono patch cords or a 75 ohm coaxial cable and connectors, which protects your receive system from an accidental connection to transmitting equipment. FVC-1 feedline voltage couplers have two LED indicators--red and green--which indicate the presence and polarity of the output control voltage selected. The LEDs may function as directional indicators that can be read at a convenient distance or they can aid in troubleshooting. Each of our DX Engineering FVC-1 Feedline Voltage Couplers comes with a heavy duty 120V AC wall transformer, which provides a safe 12V AC to operate your receive antenna system. Here are other exclusive features of FVC-1 voltage couplers: * Metal housing--superior shielding, rugged, and easy mounting * Convenient installation--mount anywhere in your shack * Rugged control connector - a reliable, solderless, and removable connector with screw conductor clamps * Internal thermal reset fuse offers full protection against accidental shorts Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Got antenna switching voltages? DX Engineering FVC-1 Feedline Voltage Couplers will solve many switching needs easily and economically!
( 1 )
$185.99
DX Engineering 2-Port Receiving Antenna Switches
DX Engineering 2-Port Receiving Antenna Switches are for receiving systems designed to allow for the selection of one of two output ports from one feedline. Typically connected to different receiving antennas, these RoHS-compliant receive antenna switches activate with the application of a control voltage injected onto the feedline of either +10-15V DC or 9-12V AC. The optional DX Engineering Feedline Voltage Coupler may be used to supply control voltages through a single main feedline. Three RLS-2 Two-Port Receiving Antenna Switches may be configured to allow control of the switching selection of four different receiving antennas. When used with two DX Engineering Reversible Beverage Systems, one of these RLS-2 units will delegate switching voltages and allow for the selection of four directions, sharing the 75 ohm feedline, and passing 500 kHz through 30 MHz receive back to the operating position. Features of DX Engineering 2-port receiving antenna switches include: * Metal housing for superior shielding and long life * High-quality components * Reliable F-type connectors * Jumper-selectable, control voltage pass-through to the activated port Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Build your special receive antenna switching system with DX Engineering 2-Port Receiving Antenna Switches!
Not Yet Reviewed
$115.99
DX Engineering Dual Module Chassis
The DX Engineering Dual Module Chassis is the connector and power interface box for all DX Engineering and Clifton Laboratories Plug-In Modules and Receive Filters. The DXE-DMC-2 is a versatile multi-purpose DX Engineering receive device box. It can be used for two passive plug-in modules or one powered module and one passive module. It is a great way to create a wide pass filter, or protect a receiver with a filter and a limiter, or add a preamplifier that has filtering or limiter protection. Here are the modules that can internally plug into the DX Engineering Dual Module Chassis: • DXE-Z10020-PM - Clifton Laboratories Z10020 AM Band Filter Module • DXE-Z10046B-PM - Clifton Laboratories Z10046 High-Gain Preamplifiers • DXE-RG5000HD-PM - Receiver Guard 5000HD Plug-in Module (passive) • DXE-IT-PM - 75 to 50 Ohm Impedance Transformer Plug-in Module (passive) • DXE-RPA-2-PM - Receive Preamplifier Plug-in Module (powered) • DXE-RXFL-1 - Receive Filter Adapter Board, for RXFL Filters (passive) One DXE-RXFL-1 Receive Filter Adapter Board is required to install any one of the RXFL filters listed below. They fit into the DXE-DMC-2, as well as the DXE-NCC-2, DXE-RTR-2 and DXE-RPA-2. The DXE-DMC-2 can accommodate one or two filters to create the filter type and input signal band pass frequency coverage and limitations that serves your needs. NOTE: The transition from the natural aluminum to the black powder coated chassis is occurring in early 2020. There is no internal electronic difference between them. Click on more details to see how you can build the receive accessory of your desires with the DX Engineering Dual Module Chassis.
( 2 )
$195.99