Availability
6 Results Found For "Receive Array"
Hi-Z® Antennas Manual Directional Control Consoles
Hi-Z® Antennas Manual Directional Control Consoles are specialized "low-side" BCD grounding switches that are specifically designed to operate Hi-Z Antennas Phasing Combiner relay units, also known as Phase Controllers. Each HIZ-MDC console controls the phasing and direction selection of only Hi-Z Antennas Receive Vertical Antenna Arrays and supplies power to the array element amplifiers. Hi-Z Antennas Manual Directional Control Consoles are attractive and convenient, featuring a large rotary switch knob and green LEDs arranged as receive array directional azimuth indicators with corresponding compass bearing degree markings on the front panel. Selection of a specific model Manual Directional Control Console (MDC) is required, corresponding to each version of Hi-Z Antennas Receive Array Phasing Combiner or legacy Phase Controller. Each console serves as a replacement for legacy, discontinued Hi-Z manual Shack Switches, and for the discontinued Hi-Z SS-2 and SS-2PLUS: • HIZ-MDC-4 works only with the multiband Four Square Arrays PC-4A and PC-4ELEMENT • HIZ-MDC-8PRO works only with the 85/113 ft. diameter multiband 8 Circle Arrays PC-8PRO and PC4-8PROUP/PLUS • HIZ-MDC-8 works only with the 200 ft./100 ft. diameter monoband 8 Circle Arrays PC-8, PC-8A and PC-8B HIZ-MDC series Manual Directional Control Consoles are stylish, rugged, and heavy — they stay in place on the desk or shelf with four large non-skid rubber feet under a Stainless Steel chassis and an appropriate black powder coated steel cover. The required multi-conductor array power and BCD control cable (purchased separately for the required number of conductors and length to the array) passes through a grommet on the rear panel and connected internally. A rear panel 2.1mm +13.8VDC power connector accepts the included mating 2.1mm plug and unterminated DC power cable, for connection to a user provided +13.8VDC 1A fused, well-filtered power supply.
Not Yet Reviewed
$159.99
Clearance
Hi-Z® Antennas Array Phase Combiner Units
Hi-Z® Antennas Array Phase Combiners are the relay unit at the center of a Hi-Z array, also known as a "phase controller." The sophisticated RF phasing and switching electronic devices have connections for the receive short element active vertical feedlines, delay lines, and the main feedline that goes to the station. Control cable connections to the phase combiner powers the array and steers the array pattern, and the station end connects to the directional control console.
Not Yet Reviewed
$325.00
$227.50
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 4 )
$249.99
DX Engineering AVA-3 Active Matching Units
DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.
( 6 )
$139.99
DX Engineering Receive Feedline Voltage Couplers
DX Engineering FVC-1 Feedline Voltage Couplers provide an interface between control switches and voltage-controlled antenna systems. These specialized controllable bias-tee devices place 0V DC, +12V DC, -12V DC, and 12V AC output voltages onto the receive antenna feedline via the 75 ohm F connector or onto a 2-conductor control line. These FVC-1 couplers function from below 500 kHz to 30 MHz and provide four selections for switching antenna array directions or changing from one array to another. These couplers were designed for use with; the DX Engineering receive-only four-square antenna systems, reversible Beverage antenna systems, and remote switches. DX Engineering switch control consoles may be connected directly to the BCD switch control input of FVC-1 couplers. Alternatively, you may use your own 12V DC voltage switching system or 1 of 4 grounding switches to control the coupler by resetting internal jumpers. The connection of the feedline voltage couplers to any radio receive antenna input is to be made using either the standard RCA phono or the F connector. This allows for the use of readily available RF-compatible RCA phono patch cords or a 75 ohm coaxial cable and connectors, which protects your receive system from an accidental connection to transmitting equipment. FVC-1 feedline voltage couplers have two LED indicators--red and green--which indicate the presence and polarity of the output control voltage selected. The LEDs may function as directional indicators that can be read at a convenient distance or they can aid in troubleshooting. Each of our DX Engineering FVC-1 Feedline Voltage Couplers comes with a heavy duty 120V AC wall transformer, which provides a safe 12V AC to operate your receive antenna system. Here are other exclusive features of FVC-1 voltage couplers: * Metal housing--superior shielding, rugged, and easy mounting * Convenient installation--mount anywhere in your shack * Rugged control connector - a reliable, solderless, and removable connector with screw conductor clamps * Internal thermal reset fuse offers full protection against accidental shorts Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Got antenna switching voltages? DX Engineering FVC-1 Feedline Voltage Couplers will solve many switching needs easily and economically!
( 1 )
$185.99
DX Engineering 2-Port Splitter-Combiners
DX Engineering 2-Port Splitter-Combiners are receive signal-level RF devices that operate from 300 kHz to 30 MHz, available in 50 ohm and 75 ohm versions. They're typically used to split one RF signal to properly feed two receivers, or the receive antenna inputs of one transceiver and one separate receiver. They also properly combine two receiving antennas in phase, such as Beverage antennas, to form a phased receive array. Important features of the DX Engineering 2-Port Splitter-Combiner: * Available for 50 ohm and 75 ohm systems * Broad, 300 kHz through 30 MHz operating range * High-quality components * Isolated ports * Metal housing for superior shielding and longer life * Reliable side-mount connectors: BNC female for 50 ohm, F female connectors for 75 ohm model * Economical solution to potential impedance errors that cause losses With the updated "SC" versions of the original 2-Port Splitter-Combiner, DX Engineering has maintained the port isolation design that prevents signal performance degradation caused by impedance errors in less-than-perfect receive systems. The normal signal level reduction when used as a splitter is just over 3 dB per port. As with any system, losses are dependent upon source and load impedances being matched. DX Engineering Splitter-Combiners provide equal power, voltage, and current to matched loads on ports 1 and 2. The primary advantage is that individual receiver input variations, or a band filter attached to only one port, will not seriously affect the signal level in the other receiver. In addition, any spurious signals generated in one receiver are greatly attenuated by the 2-Port Splitter-Combiner before reaching the second receiver. When splitting in-phase signals, the loss is somewhat less. Any unused port of the 2-Port Splitter-Combiner should be terminated and specified losses are based on source and load impedances being matched. The DX Engineering 2-Port Splitter-Combiner is a passive device; therefore it requires no power to operate. Use the 75-ohm version for combining two 75 ohm antenna feedlines into a single 75 ohm feedline with negligible loss; or use the 50-ohm version for 50-ohm antennas and feedlines. Examples for applications are for two antennas forming an in-phase (broadside) receiving array, a cross-fire Echelon Beverage array, or any type of array with fixed phasing. There are a number of advantages to using these units for combining antenna systems over a standard parallel connection: * Splitter-Combiners match the entire antenna system to the feedline impedance; conversely, paralleling feedlines by using a T-connector divides the impedance in half, causing mismatched losses * With antennas connected directly in parallel, if either one develops a high impedance open, becomes shorted, falls down, or has a feedline problem, the entire antenna system may become unusable. By using the 2-Port Splitter-Combiner, only the problem antenna is unusable; the antenna on the other port can still be used * Unlike quarter wave matching sections that only work on one band, these Splitter-Combiners have extremely wide bandwidth * Due to the built-in isolation and balancing, these units limit the signal loss to approximately 3 dB per port * 2-Port Splitter-Combiners provide very high isolation between ports 1 and 2; this prevents either antenna from interfering with the other during normal operation Note: These devices cannot be used for FM broadcast, VHF, UHF, CATV or Satellite TV. They operate only MF through HF. Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 5 )
$100.99
—
$107.99