Availability
19 Results Found For "noise"
WiMo QRM Eliminator
The WiMo QRM Eliminator is a simple signal phasing device that can effectively reduce or remove noise interference for dramatically improved reception from 3.5 to 60 MHz. The QRM Eliminator is based on a totally innovative concept and cannot be compared to the performance of noise blanker or DSP circuits. Removing the noise before it gets to the receiver is the superior method of interference reduction. With the WiMo QRM Eliminator you can get rid of local interference almost entirely, up to an S9 level, with the likely result of completely clear reception! You don't have to understand the cause or type of interference nor do you need to know the location of its source. It doesn't matter if the interference originates from your own station or from a welding unit hundreds of feet away. The QRM Eliminator simply connects to the antenna port of transceiver and to the antenna (or amplifier input), without any radio modifications required. An additional user supplied auxiliary receiving antenna is required, such as a properly positioned 8 ft. outdoor dipole antenna or a simple 20 ft. wire in the shack, for example. This "noise sense" antenna receives mostly unwanted signal, while the transmitting antenna receives the same interference in a different phase along with the desired signal. The QRM Eliminator allows the adjustment of the amplification and phase to cancel out the unwanted signal before it reaches the receiver front end! Noise or interference nulling can provide over 45 dB of unwanted signal suppression, in many cases resulting in clear reception of the desired signal. The QRM Eliminator is built into a shielded metal enclosure, functions over the frequency range of 3.5 through 60 MHz, and has a status LED to indicate when the unit is turned on for phasing. The unit has a built-in T/R relay with PTT control via a rear panel RCA phono connector for the transceiver amplifier keying line. The QRM Eliminator automatically switches the Main antenna connection to the transceiver during transmit. Also, simply turn the unit off to bypass the phasing unit for normal reception on the Main transmit antenna. Click "More Detail" below to see additional information about this exciting device. You may not believe the power of interference phase nulling until you have experienced it for yourself. Order the WiMo QRM Eliminator exclusively in North America from DX Engineering.
( 25 )
$229.99
DX Engineering AVA-3 Active Matching Units
DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.
( 6 )
$139.99
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit is based on the design by Don Kirk, WD8DSB. Don's article on this antenna is published in the March 2021 issue of QST Magazine (used by permission). The DXE-NOISELOOP is a kit of parts to build this receive-only portable directional HF loop antenna, which measures only 48 by 24 inches plus 36 inches of mast-handle. It may be used while walking or stationary with your portable HF receiver. Oriented vertically, this loop antenna features a cardioid pattern at the horizon with a deep null of up to 30 dB rejection. It is an excellent tool for locating noise sources from 1.8 through 30 MHz and for low-noise, general coverage reception from the AM broadcast band through 30 MHz. An optional Preamplifier-Attenuator Unit, DXE-NL-PRE-ATT-1, may be attached to the loop mast handle for enhanced operations. An IC-705, a portable SW or a handheld HF receiver are excellent choices for searching for local noise sources with the NOISELOOP, around the neighborhood and even around your own home. This Portable Flag Antenna Kit includes everything needed to make the antenna: fiberglass tubing for the frame and handle, mounting plate, separate PC boards for the bifilar wound transformer and load resistor, antenna wire, coaxial cable with male BNC and stainless steel hardware. Simple hand tools and a solder iron are required for assembly. Included instructions detail assembly. This kit will typically take between 1 and 2 hours to build. The WD8DSB Portable Flag Antenna design has become a real game changer in direction finding of RFI on MF and HF frequencies, and you will also find it an invaluable tool when hunting RFI due to the following key features. *Unidirectional (unlike a tuned loop) *Broadband (unlike a tuned loop, excellent for AM DXing, SWL and Amateur) *Portable (easy to walk with while directional noise finding or HF Fox Hunting) Traditionally Flag antennas are large and designed for stationary use, but the idea for this antenna was to design a Portable Flag. It was designed to be the largest possible (to maximize gain) that would fit inside a car and it's still small enough to maintain a cardioid pattern up through 30 MHz. The portable Flag has an approximate dimension of 2 feet tall by 4 feet long which you (or a helper) can easily walk with while tracking down a signal. Unlike a tuned loop, the Portable Flag is a broadband antenna with unidirectional properties, and it's designed for direction finding from 1.8 to 30 MHz as long as an appropriate preamp is used. It's even useful for direction finding down in the AM broadcast band. The rear of the antenna produces a sharp null when pointed at the signal of interest and the sharp null is often used for direction finding versus using the broad peak which occurs when the front of the antenna is pointed at the signal of interest. Learn more about how to build this antenna kit by clicking on More Detail and the Documentation link for the Instruction Manual. Order your DX Engineering NOISELOOP Portable Receive Flag Antenna Kit here.
( 15 )
$159.99
DX Engineering Receiver Guard Electronic RF Limiters
DX Engineering Receiver Guard RG5000HD Electronic RF Limiters are the best choice of inline devices to protect your receiver antenna inputs. The Receiver Guard is a receive antenna input limiter specifically designed to protect a sensitive receiver front-end against high levels of RF and potential damage. At the heart of each Receiver Guard is a highly effective electronic RF limiter covering 500 kHz to 150 MHz with an insertion loss under 0.15 dB up to 50 MHz and under 0.30 dB up to 150 MHz. The multi-stage design includes a gas discharge tube for maximum pulse energy protection. The DXE-RG5000HD rejects 10 watts of catastrophic receive antenna feedline RF while passing a maximum signal of about 87 dB over S-9, which is only 25 mw, a signal level that is well below the point of front end damage. Receiver Guards are a must for multiple radio contesting stations and they provide low-cost front-end "insurance." Use them in these common high-RF situations: - Receive antennas in very close proximity to transmit antennas - Field-day operations with many transmitters in close range - Multi-transmitter contesting sites - Neighboring Amateur and CB operators - Frequent high-power mobile encounters Extensively tested and proven in real-world stations, the Receiver Guard works for all radios and offers the ultimate performance required by the upper tier of transceivers tested to have the best narrow-spaced third-order dynamic range or published RMDR (Reciprocal Mixing Dynamic Range). These are passive electronic limiters, so competitive contesting stations use separate band filters in addition to the Receiver Guard. When there are high levels of RF on your receive antennas, the DX Engineering Receiver Guard generates far less harmonic noise than other limiters on the market, which allows your station to continue to operate safely and competitively. At normal HF signal levels the RG5000HD operates continuously with no effect on the performance of your station while providing the best possible protection for your radio. Here are key Receiver Guard features: * Keeps stray high levels of RF from damaging your receiver input * Ideal for separate 160 and/or 80 meter receive systems with large pulse and RF energy capture area * Uses state of the art components for maximum protection of receivers * Under 6 ns response time * Multi-Stage protection * Very low insertion loss * Uses BNC type connectors to avoid accidental connection to a transmit feedline * Has been developed and tested in world-recognized multi-multi contest station K3LR Specifications - DX Engineering Receiver Guard model DXE-RG-5000HD - Frequency Range: 0.5 through 150 MHz - Insertion Loss: < 0.15 dB up to 50 MHz, < 0.3 dB 50 MHz up to 150 MHz - VSWR: < 1.2:1 - Maximum Output Level at 10 W input: +14 dBm (0.025 W) - Maximum Power Handling: 10 W CCS (Continuous Commercial Service) - Device Impedance: 50 to 75 ohms, unbalanced - Connectors, Input and Output: BNC female Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. What happens if the receive antenna is extremely close to the transmit antenna, or there is an antenna support or other system failure that causes a high RF level to enter the receive antenna input? A DX Engineering Receiver Guard can save the day! Order yours now.
( 37 )
$119.99
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 3 )
$249.99
Chelegance WV-601 Aluminum All Band Passive Loop Antennas
Chelegance WV-601 Aluminum All Band Passive Loop Antennas provide low noise, directional receive coverage across all frequencies from 0-999MHz. This broadband antenna is passive, meaning that it doesn't require power in order to operate, and that helps it to be low noise as it doesn't amplify both the signals that you want to hear and the noise that you don't want to hear. The WV-601 is a broadband antenna provides reception across the Long Wave (144-288KHz), Medium Wave (540-1700KHz), Short Wave (2.3-30MHz), FM Broadcast (64-108MHz), VHF Air band (118-137MHz), VHF (140-380MHz), UHF (380-512MHz) and the UHF Public Service bands (770-860MHz), as well as everything in between. In addition to the broadband receive, this loop antenna can be used for transmit on the 2m and 70cm bands at 10 watts or less. At a mere 27.6 in. in diameter, and weighing in at 4.4 lbs., this antenna doesn't require much in the way of a mast to support it and it can even be used portable should one wish to do so. This allows for use on events like Field Day or even a POTA activation. This antenna comes with: • Antenna Loop • Supporting Mast with installing accessories • 10-meter Feedline (BNC male to BNC female connector) • 1-meter Feedline (3.5 to BNC male) • 1-meter Feedline (BNC male to BNC male) • SMA Adapter • User Manual Additional Feature and Specifications: Frequency Range RX: 0 – 999MHz / TX: 144 – 148MHz & 430 – 440MHz Net Weight 2kg (antenna) / 5kg (packaged）
( 2 )
$186.99
Unified Microsystems RAS-4 Receive Antenna Switch
Unified Microsystems RAS-4 Receive Antenna Switch is an outdoor capable remote relay unit that allows the operator to select up to four antennas. Receive only antennas are critical for success on the low bands. Due to the wavelengths of the low bands, these antennas cannot be rotated. Several very effective receive only antennas are mono-directional or bi-directional, including Beverage, Reversible Beverage, Beverage on the Ground (BOG), Reversible Beverage on the Ground (RBOG) and many others,. Therefore, a high quality, low noise four port receive antenna switch is required to cover all of the directions with multiple antennas. Common mode noise pick up can ruin the performance of receive antenna systems, so the RAS-4 isolates both the center conductor and shield of unselected ports. An internal bifilar ferrite choke further reduces common mode currents. This unit features female F connectors for RG6U coax with male F connectors, the standard field-serviceable coaxial cable assemblies for receive antenna systems. A very important requirement for dual feedline Reversible Beverage and RBOG antennas is provided by the RAS-4. By default, unselected ports are terminated for 75 ohms. The user can change to 50 ohm, open circuit, or center conductor-shield short by soldering wire jumpers. The RAS-4 is housed in a NEMA rated enclosure with a gasket lid. A cable gland seals the control cable entry. The internal circuit board has a conformal coating for additional protection. The RAS-4 can be mounted outdoors, with the enclosure flanges or with the included L bracket for mounting to a pole or post. The RAS-4 Receive Antenna Switch is a receive-only relay unit that cannot be used for transmitting antennas. The required in-shack control console switch is not included. The RAS-4 will work with a commercial or a simple home brewed, positive 12V One-of-Four switch. Choose from DX Engineering, EA4TX and others for manual or automated switching. Unified Microsystems RAS-4 Receive Antenna Switch Specifications Antenna Selection: 4 receive antennas to 1 main feedline Dimensions: Approx. 4.5 x 3.5 x 3.25 in. (11.4 x 8.9 x 8.3 cm), not including the bracket. Connector type: F (5 total) Unselected port termination: 75 ohm default; 50 ohm; open; shorted. Wire jumper selectable VSWR: < 1.5:1 from 100 kHz to 20 MHz Insertion loss: < 0.4dB from 100 kHz to 20 MHz Port to Port Isolation: > 45dB from 100 kHz to 20 MHz Control Cable: 3 wire plus ground (4 total conductors), Not included Switch Controller: 12 to 14 Vdc, Not included
( 2 )
$124.95
Antennas-Amplifiers 6400 1.25-meter Receive Band Pass Filters
Antennas-Amplifiers 6400 1.25-meter Receive Band Pass Filters are optimized for the 1.25-meter (220–225MHz) amateur band, these filters deliver reliable 50 ohm performance with <0.25 dB insertion loss, preserving weak signals while reducing out of band interference. N type female connectors ensure consistent, low loss connections, and the filter's long lasting construction makes it a smart, economical choice for operators seeking enhanced receive performance without compromise. Antennas-Amplifiers continues to set the standard in high performance RF engineering, offering one of the broadest and most advanced collections of ham radio antennas, low noise components, and precision band pass filters available today. The 6400 Series 1.25 meter Receive Band Pass Filters are expertly engineered with high Q designs and exceptionally low insertion loss, ensuring outstanding selectivity and signal purity across demanding multi station, contest, and DX environments.
Not Yet Reviewed
$139.99
Antennas-Amplifiers 6250 2-meter Receive Band Pass Filters
Antennas Amplifiers 6250 2 Meter Receive Band Pass Filters offer an economical and highly effective solution for operators seeking clean, selective performance across the 144–148MHz VHF 2-meter band. Designed with carefully tuned, high selectivity circuitry, these filters maintain an impressively low insertion loss of under 0.4 dB, ensuring excellent signal transparency while minimizing degradation of weak signals. Precise engineering and adjustment techniques deliver an input return loss better than –20dB, providing stable, low noise operation ideal for sensitive receive paths. Featuring a 50 ohm nominal impedance and N-Type connectors, the 6250 filters integrate seamlessly into a wide range of 2 meter receive only setups, including weak signal stations, repeater sites, satellite ground stations, and multi radio environments where strong out of band signals can impair performance. These filters offer a reliable, cost effective way to enhance 2 meter reception while protecting front end equipment from unwanted interference.
Not Yet Reviewed
$129.99
DX Engineering NCC-2 Receive Filter Sets
DX Engineering NCC-2 Receive Filter Sets provide an added dimension to the receive capabilities of the NCC-2 Receive Antenna Phasing System. These advanced plug-in filter module and adapter board pairs offer frequency-specific receive enhancements. The packages are available in pairs of high pass, band pass, and low pass frequency ranges with filter cut-off and center frequencies that correspond to the major Amateur low bands, 160, 80, 40 meters. Filter insertion loss is only about 1 dB. NCC-2 Receive Filter Sets are pairs of the original NCC-1 filters of the same type, each with the required RXFL-1 Filter Adapter. Both NCC-2 channels, "CH A RX ANT IN" and "CH B RX ANT IN" will benefit from the same pass-band characteristics. High pass, band pass, or low pass filter sets are available for users to choose and install into their NCC-2 for their desired application. By reducing or excluding frequency-specific interfering noise and signals, the noise floor of the desired passband can be dramatically lowered for greatly improved reception. Be aware that when filter pairs are installed, the NCC-2 no longer responds to signals out of the passband. In other words, at this time there is no electronically switched bypass for installed filters. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. The NCC-2 Receive Filters displayed here, and higher frequency band filters, are also available as single filters for the NCC-2, to create alternative wide-pass filter sets, and for DX Engineering single channel accessories, including the DXE-RPA-2, DXE-DMC-2 and the DXE RTR-2. The simplest way to filter your NCC-2 is to order one of these DX Engineering Receive Filter Sets for your unit and enjoy the best possible filtered performance from your DX Engineering NCC-2 Receive Antenna Phasing System.
Not Yet Reviewed
$106.96
—
$238.96
Antennas-Amplifiers 6505 70cm Low Loss Receive Band Pass Filters
Antennas-Amplifiers 6505 70cm Low Loss Receive Band Pass Filters are engineered for optimal performance in weak signal, terrestrial, and EME applications. Designed for direct connection to a coaxial relay, the 6505 filter minimizes insertion loss in the receive path, ensuring that wideband preamplifiers experience virtually no degradation to their noise performance. By sharply rejecting strong out of band signals, the 6505 provides stable operation in environments with strong adjacent band or high power local signals. The filter is housed in a sturdy 0.8 mm brass enclosure, providing excellent mechanical stability, long term durability, and consistent electrical characteristics over time.
Not Yet Reviewed
$175.99
Antennas-Amplifiers 5900 6-meter Receive Band Pass Filters
Antennas-Amplifiers 5900 6-meter Receive Band Pass Filters deliver exceptional performance on the legendary 6m "Magic Band," offering high selectivity, high Q design, and impressively low insertion loss—all in an economical package. Engineered to confine received signals strictly within the 50–54 MHz amateur band, these filters dramatically reduce out of band noise, lowering the noise floor and enhancing weak signal reception. When placed ahead of SDRs or wideband receivers, users will immediately notice how effectively these filters remove unwanted HF, 4m, FM broadcast, 2m, and 70cm signals, leaving a clean and focused 6m passband. In multi operator contest stations or portable field setups, they provide essential isolation by minimizing images and harmonic interference, ensuring crisp mono band operation even in crowded RF environments. These 6 meter band pass filters are the ideal choice for operators seeking cleaner signals, improved performance, and reliable protection for sensitive front end equipment.
Not Yet Reviewed
$129.99
Antennas-Amplifiers 5910 Low Loss 6-meter Receive Band Pass Filters
Antennas Amplifiers 5910 Low Loss 6 meter Receive Band Pass Filters deliver exceptional performance on the legendary 6m "Magic Band," offering high selectivity, a high Q design, and impressively low insertion loss. Engineered to confine received signals strictly within the 50–51 MHz amateur band, these filters dramatically reduce out of band noise, lowering the noise floor and enhancing weak signal reception. When placed ahead of SDRs or wideband receivers, they effectively remove unwanted HF, 4m, FM broadcast, 2m, and 70cm signals, leaving us with a clean and focused 6m passband. Just as important, these filters will not disturb the noise performance of preamplifiers—an essential advantage for contesting, DXing, and EME—while ensuring smooth, stable operation even in the presence of strong nearby signals. With an insertion loss of just 0.1 dB, they safeguard receiving performance without compromise, a level of efficiency achieved through careful design and precise tuning. In multi operator contest stations or portable field setups, they provide essential isolation by minimizing images and harmonic interference, ensuring crisp monoband operation even in crowded RF environments. These 6 meter band pass filters are the ideal choice for operators seeking cleaner signals, improved performance, and reliable protection for sensitive front end equipment.
( 1 )
$180.99
Antennas-Amplifiers 6500 Ultra Low Loss 70cm Receive Band Pass Filters
Antennas-Amplifiers 6500 Ultra Low Loss 70cm Receive Band Pass Filters are especially engineered for high performance terrestrial and EME applications. Placed ahead of any wideband LNA, it prevents overload and desensitization caused by strong out of band signals while preserving the amplifier's noise figure. It's precisely defined 430–450MHz passband ensures clean signal reception without compromising weak signal performance, even in demanding RF environments. Designed for stations requiring maximum front end protection with minimal insertion loss, this filter delivers exceptionally high input return loss and rugged, reliable connectivity through N type female connectors.
Not Yet Reviewed
$170.99
DX Engineering NCC-1 Receive Filter Sets
DX Engineering announces a series of NCC-1 Receive Filter Sets, a breakthrough option for owners of the NCC-1 Receive Antenna Phasing Unit. These advanced plug-in filter module sets offer frequency-specific receive antenna system enhancements for the NCC-1. All filter modules sets are available in matched pairs of low-pass, band-pass and high-pass frequency ranges. Filter cut-off and center frequencies correspond to the major Amateur bands, 160, 80, 40, 20, 15 and 10 meters, with filter module insertion loss of only about 1 dB. Highly regarded by many owners and engineers to be the best receive phasing and noise canceling unit available, the DX Engineering NCC-1 is used extensively by enthusiasts in Amateur Radio DXing, Contesting, AM DXing, and Short-Wave Listening (SWL), and is also used in commercial AM and HF broadcast applications. DX Engineering NCC-1 Receive Filter Sets add a new dimension of functionality to the NCC-1, for advanced directional noise and signal nulling performance, enhanced with specific frequency range operations. By default, NCC-1 filter slots are jumpered to pass all signals. On the NCC-1 front panel, the BAND toggle switch "L" or "H" positions each activate one of two filter pair slots, allowing over 360 degrees of phase rotation in two frequency ranges. The BAND switch "L" position covers from 850 kHz to 8 MHz. The BAND switch "H" position covers from 2 MHz to 15 MHz. Frequencies outside these ranges will have less than 360 degrees of phase rotation. NCC-1 Receive Filter Sets must be placed into the proper BAND filter slots corresponding to desired usage. NCC-1 Receive Filter Sets are pairs of filters (2 of the same type), so both NCC-1 receive antenna inputs "A" and "B" exhibit the same pass-band characteristics. Band-pass, high-pass or low-pass filters are available for users to choose and install into their NCC-1 for their desired application. By reducing or excluding frequency-specific interfering noise and signals, the noise floor of the desired pass-band can be lowered for dramatically improved reception. You can install one set or two sets, depending on your desired filtering. NCC-1 "L" and "H" slots may be populated with pairs of band-pass, high-pass, or low-pass filters to suit the specific signal rejection needs of the discerning operator. As an example, an 80 meter DX enthusiast may elect to install two 80 meter band pass NCC-1 Receive Filters, part number DXE-NCCFL-BPF80M, into their NCC-1 "L" BAND slots. This would dedicate their NCC-1 to 80 meter-only operations. Setting the BAND switch to "L" would dramatically reduce noise and signals from outside the 80 meter band, very effectively excluding interference from nearby AM Broadcast, 160 and 40 meter stations. A much lower noise floor on 80 meters could be achieved for dramatically enhanced reception of weak 80 meter DX signals. An additional pair of filters could be installed into the "H" BAND slots, to enhance reception on the higher HF bands. For example, installing 20 meter high pass filters, part number DXE-NCCFL-HP20M, and switching to BAND H would drastically reduce all received noise and signals from frequencies below 13.70 MHz. With advanced planning of additional filter availability, an NCC-1 owner could even swap different filter sets for optimal operations in different contests or band pursuits. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. All NCC-1 Receive Filter Sets displayed here are also conveniently listed on a single page in the link tab called "Documentation." Order one or two DX Engineering NCC-1 Receive Filter Sets for your unit and enjoy the best possible performance from your NCC-1.
Not Yet Reviewed
$103.97
—
$215.97
Antennas-Amplifiers 6265 2-meter Receive Band Pass Filters
Antennas-Amplifiers 6265 2-meter Receive Band Pass Filters are designed for operators who demand uncompromising weak signal performance across the 144–146MHz frequency range. Built with high Q coils and capacitors, these filters achieve exceptionally low loss, preserving receive sensitivity for DXing, contesting, and EME where every fraction of a decibel matters. Beyond enhancing desired signals, the 6265 excels at suppressing interference from strong HF, 6 meter, 1.25 meter, and 70 centimeter stations, providing a cleaner, more stable noise floor in challenging multi band environments. The RF connector positions are intentionally arranged to allow direct connection to a coaxial relay, eliminating additional coax runs and maximizing front end performance. Housed in a rugged brass enclosure, these filter delivers durability, stability, and the level of RF excellence expected by serious VHF operators seeking top tier receive chain protection.
Not Yet Reviewed
$175.99
DX Engineering Beverage Antenna Systems
DX Engineering Beverage Antenna Systems are single-wire, single-direction beverage feed systems. Their W8JI design makes them immune to the strong signal overload and core saturation common in multi-transmitter contesting environments. They are used by winning contest stations and low-band DXers. They use an isolated-winding matching-transformer system to significantly increase the signal-to-noise ratio in Beverage and other high-impedance antennas. Now RoHS-compliant, they will work with antenna impedances from 400-500 ohms. The termination resistor included is a special 470 ohm, 2 watt, non-inductive resistor that withstands nearby lightning strikes significantly better than hard-to-find carbon composition resistors. Features include: * 100 kHz to 30 MHz operating range * Spark gaps minimize damage from lightning * Wing nut terminals eliminate soldering * Rugged aluminum housing and stainless steel hardware * Flange-mount holes for easy mounting * Ground isolated secondary can be connected with normal or reverse phase Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Beverage antennas have been in use since the 1920s. These DX Engineering Beverage Antenna Systems modernize the Beverage concept for convenience and performance.
( 21 )
$115.99
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$103.99
DX Engineering Dual Module Chassis
The DX Engineering Dual Module Chassis is the connector and power interface box for all DX Engineering and Clifton Laboratories Plug-In Modules and Receive Filters. The DXE-DMC-2 is a versatile multi-purpose DX Engineering receive device box. It can be used for two passive plug-in modules or one powered module and one passive module. It is a great way to create a wide pass filter, or protect a receiver with a filter and a limiter, or add a preamplifier that has filtering or limiter protection. Here are the modules that can internally plug into the DX Engineering Dual Module Chassis: • DXE-Z10020-PM - Clifton Laboratories Z10020 AM Band Filter Module • DXE-Z10046B-PM - Clifton Laboratories Z10046 High-Gain Preamplifiers • DXE-RG5000HD-PM - Receiver Guard 5000HD Plug-in Module (passive) • DXE-IT-PM - 75 to 50 Ohm Impedance Transformer Plug-in Module (passive) • DXE-RPA-2-PM - Receive Preamplifier Plug-in Module (powered) • DXE-RXFL-1 - Receive Filter Adapter Board, for RXFL Filters (passive) One DXE-RXFL-1 Receive Filter Adapter Board is required to install any one of the RXFL filters listed below. They fit into the DXE-DMC-2, as well as the DXE-NCC-2, DXE-RTR-2 and DXE-RPA-2. The DXE-DMC-2 can accommodate one or two filters to create the filter type and input signal band pass frequency coverage and limitations that serves your needs. NOTE: The transition from the natural aluminum to the black powder coated chassis is occurring in early 2020. There is no internal electronic difference between them. Click on more details to see how you can build the receive accessory of your desires with the DX Engineering Dual Module Chassis.
( 2 )
$195.99