Availability
Antennas
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-2800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-2800DXA, G-1000DXA and G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 30 sq. ft. of antenna wind load and over 650 lbs. of vertical mast load. About 130 ft. of control cable is included with the G-2800DXA only. Control console power is 110/120 volts AC. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 50 to 120 seconds on the G-2800DXA, and preset a desired heading for the rotator, to which it then turns automatically. When a fast rotation speed is selected, special "auto slow-start" and "auto slow-stop" features avoid sharp jolts to the antenna array and tower. Activating the rotator causes it to begin turning at slow, but increasing, speed. As the antenna approaches the desired heading, the rotation automatically slows down, before bringing the antenna to a gentle stop. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-2800DXA Extra Heavy-Duty Rotator System from DX Engineering.
( 1 )
$1,769.99
Ciro Mazzoni Automatic Magnetic Loop Antennas
Ciro Mazzoni Automatic Magnetic Loop Antennas are ideal stealth HOA and small-space loop antennas. They provide exciting new capabilities to limited space operations with unparalleled reliability and dramatically higher power handling compared to other transmitting loops. These are considered to be the best small transmitting loops available in the world! They are constructed with tough, attractive, aircraft grade aluminum. In spite of their compact size, these antennas automatically adjust to resonance throughout a wide band range: the MIDI Loop tunes 80 through 20 meters, the BABY tunes 40 through 10 meters... without any coverage gap! Now, THE STEALTH LOOP adds even more versatility for the Amateur who is shackled by antenna restrictions. Use it on the ground or on a table! Click on the STEALTH below for More Details! For each LOOP Antenna, MIDI, BABY and THE STEALTH LOOP, frequency information is directly transferred from your radio (ICOM, Elecraft, Kenwood, and Yaesu) to the included ATU 2.0 Controller, by RS-232 or Interface Cable. The Loop Antenna tunes automatically to the radio frequency or manual tuning is available with the ATU 2.0 USB Keypad, also included. If you need a very-high quality antenna that is concealable and operates at respectable power over a wide frequency range, then Ciro Mazzoni Automatic Magnetic Loop Antennas are a great choice!
( 49 )
$1,999.99
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 3 )
$1,999.92
InnovAntennas DXR Series Multi-Band HF Beams
InnovAntennas DXR Series Multi-Band HF Beams have short booms with full-size elements or capacity-loaded shortened elements, all with excellent performance, making them very popular internationally. The DXR Series interlaced-element antennas, optimized by G0KSC over a long period of time, achieve the best possible balance between compact size and performance. For the DXR Series Multi-band Yagis, equal attention was paid to a very solid construction and sufficiently small component and packaging size, to keep shipping costs within reasonable limits. Click on any model listed for specific details and specifications. InnovAntennas DXR Series Multi-Band HF Beams are available exclusively from DX Engineering in North America. Important features of InnovAntennas DXR Series Multi-Band HF Beams: * No traps, matching links, or hairpins * Only one feed line for all bands * Careful selection of materials without regard to cost * Very robust construction with still manageable package size The DXR Series beams use a 1.97 x 1.97 in. (50 x 50 mm) square boom with 0.078 in. (2 mm) wall thickness. A square boom has the advantage that the elements cannot twist in the plane. On the other hand, it is slightly heavier than a round boom of the same stiffness. The DXR Yagis do not require any bracing of the boom. The longest elements are 1.378 in. (35 mm) diameter in the middle and taper relatively quickly to achieve a good compromise between weight and strength. This construction also helps to avoid constant vibration even in light winds. With these multi-band Yagis, care has been taken to ensure that there are never more than the elements of three bands nested within each other. This is because each additional element for one band can cause interference on another band. This negative effect was avoided by careful manual optimization. The result is the best possible matching over a wider band range than other antenna designs. In most cases, no tuner is necessary; the SWR minimum can be precisely set by adjusting the element lengths. Due to the robust construction and the absence of moving or electrically active components such as coils, traps, hairpins, etc., an InnovAntennas DXR beam is maintenance-free for many years. The insulators are UV-resistant and designed for a wide temperature range. The mounting hardware uses sea-water resistant stainless steel and the aluminum is type T6 6066/6082, which is also used in aviation. It is nice not to have to climb the mast every year to maintain the antenna. The DXR Series Multiband beams are designed to require only one feed line. This makes installation on a mast with a rotor very easy. And the use of modern SDR transceivers, which allow the observation of several bands at the same time, becomes really useful. The one feed line is connected directly to the solid distribution rails of the fed elements. By avoiding baluns, matching elements, traps, or hairpins for tuning, transmit power is only limited by the coaxial cable and connectors. Note: Front-to-back ratio (F/B) and SWR bandwidth data for the DXR Series will be added as it becomes available. Many models of the DXR Series are available as a "super-compact" version, on which the longest elements have been shortened with capacity hats, thus reducing their turning radius considerably. The installation of these impressive antennas is possible even where space is limited.
( 4 )
$1,775.99
—
$1,899.99
Diex Antennas DXS Series Multiband Directional Antennas
Diex Antennas DXS Series Multi-band 3 Element Yagi Antennas delivers high-performance, Multi-band operation for the 40, 20, 15, 10 and 6-meter amateur bands. The DXS antenna series features three tunable aluminum elements, engineered for optimal directionality and gain. With a power handling capacity of up to 1,500 watts, these antennas are built to perform under demanding conditions. Crafted in Brazil using quality materials, the DXS Series is designed for long-lasting, trouble-free service. Easy to assemble and require only a modest mast or tower, these antennas offer an economical and effective solution for getting on the air.
( 1 )
$1,632.99
—
$1,745.99
OptiBeam HF Directional Antennas
OptiBeam antenna technology has achieved directional antennas with extraordinary electrical properties, including the highest efficiency, optimum band coverage, nearly constant gain and unchanging radiation pattern across the band, and low SWR. These antennas maintain consistent electrical characteristics under all weather-conditions and include a high power balun with UHF female connector for your 50 Ohm coaxial cable. OptiBeam Antennas are distinguished by their advanced mechanical qualities. Specially configured, stable and properly shaped element holders, robust square and round booms with effective and very solidly-built element transitions are OptiBeam exclusives. They provide advanced physical properties, including proper balance and the highest stability of the entire system. Elements are perfectly aligned and secured against torsion with minimal sag for a visually pleasing appearance. OptiBeam antennas are made for those who understand the true value of investing in proven electrical performance and unequalled mechanical quality for the ultimate in reliability. They are built to withstand the harshest conditions using the very best materials, including high quality aluminum alloys, UV stable synthetic parts and stainless steel hardware. OptiBeam antennas are designed to be easier to build than others, arriving in subassemblies with every part carefully sorted, clearly labeled, and extremely well packed for worry-free shipment and straightforward installation. In 2025, the OptiBeam brand of products was exclusively acquired by WiMo Antennen und Elektronik GmbH. The OptiBeam portfolio is now produced by WiMo and integrated into its product offering. With this acquisition, WiMo will integrate the technical expertise and know-how gained from OptiBeam's many years of experience in antenna technology and will provide new impetus with its extensive service and sales network. The primary goal is to successfully continue OptiBeam's antennas, ensure long-term customer service and spare parts availability, and leverage development potential. For enthusiastic operators of all pursuits, OptiBeam provides the advantage of pure performance. Proven in the field and confirmed by the most demanding hams around the world – choose OptiBeam for your station.
( 5 )
$1,699.99
—
$1,869.99
InnovAntennas DXE12-6 Heavy Duty HF+6M Yagi
InnovAntennas "DXE Twelve-Six" is a heavy-duty 12 element multi-band HF plus Yagi that covers the 20, 17, 15, 12, 10 and 6 meter bands with a single coax connection to match modern HF+6m transceivers. Excellent performance on each band is achieved by direct feed and no traps, coils or hairpins for class-leading radiating efficiency. This ruggedly built beam antenna is ready for harsh weather environments with aerospace grade T6 6066/6082 aluminum tubing, UV and temperature protected insulators and all stainless steel hardware. The stout, modest length 17.5 ft. (5.33m) boom is made of 2 inch (50mm) square tubing and perfectly interleaved rigid fast-taper elements easily shed the wind. Choose this HF beam for long-term reliability and power handling that exceeds most coax specs. With low SWR across all six bands, 20 through 6 meters, InnovAntennas DXE 12-6 is a great value that packs a punch.
Not Yet Reviewed
$1,860.00
Diex Antennas Multi-Band Log Periodic Antenna
Diex Antennas Multi-Band Log Periodic Antennas deliver exceptional directionality and full coverage across the 20 through 10-meter amateur bands. Expertly engineered and crafted in Brazil using high-quality aluminum tubing and durable materials, these antennas are built to endure harsh environments while providing long-lasting, high-performance operation. With a power rating of up to 2000 Watts PEP or 700 Watts continuous duty, these antennas are ready for demanding applications. It offers 8.55dBi of gain, helping your signal reach farther—whether across the country or around the globe. Designed for efficiency, the Diex Log Periodic maintains a low SWR across its entire frequency range, minimizing the need for adjustments or an external antenna tuner.
Not Yet Reviewed
$1,699.99
DX Engineering 80 Meter Self Supporting Heavy Duty Vertical Antennas
DX Engineering 80 Meter Self Supporting Heavy Duty Vertical Antennas, model DXE-7580FS-VA-2, are high performance vertical antennas specifically designed for the 75/80 meter band. These DX Engineering 70.5 ft. vertical antennas allow you to achieve the strongest possible presence at your power level and be competitive. These are FULL SIZE, quarter-wave vertical antennas that deliver fantastic specs and the highest possible performance at a price that can easily be justified. Every design detail of the DXE-7580FS-VA-2 Heavy Duty Verticals provide for a very rugged 80 meter antenna that can stay up with no guying necessary and no worry. A 3 in. O.D. thick-wall 6061 aluminum tubing base and an extra-large insulating channel are combined with a patented* heavy duty stainless steel pivoting fixture that is second to none. Engineered for ease of assembly and adjustments, with corrosion-resistant aluminum tubing, stainless steel mounting brackets, and stainless steel hardware, these are very durable and attractive self-supporting antennas. If an extreme wind storm is predicted, one operator can easily lower and raise these antennas safely, due to the simplicity of the included Heavy Duty Pivoting Fixture and optional DXE-VRW-1 Manual Winch. DX Engineering 80 Meter Self Supporting Heavy Duty Vertical Antennas offer full band coverage, with a 2:1 SWR bandwidth of up to 557 kHz, depending on your radial field. Your internal tuner can get the SWR down to 1:1 on any DX frequency for maximum power transfer. DX Engineering 80 Meter Full Size Quarter Wave Heavy Duty Vertical Antennas feature: -- Self-supporting – will withstand steady-state winds in excess of 92 MPH without guying (guying required under extreme wind speed conditions) -- 5 kW SSB and CW rated—unparalleled reliability -- Ultra-rugged construction starts with 3 in. O.D. aircraft-grade heavy wall tubing -- Ultra-wide SWR bandwidth and unbeaten gain -- Highest wind ratings--high strength 6063/6061 tubing manufactured to DX Engineering specifications -- Easy tilt up and down-- Unique fold-over antenna mount features DX Engineering's patented stainless steel Pivoting Fixture, *U.S. Patent Number 8,130,168 -- High power handling and high strength, UV protected EXTREN® insulators -- No rust--100 percent stainless steel tubing clamps and hardware -- Reliability second to none--specially manufactured stainless and aluminum saddle clamps, stainless bolts, and precision machining on each antenna This antenna system requires the installation of a heavy duty mounting pipe set in concrete. Specifically, 3 in. OD high strength galvanized steel tubing with 0.250 in. minimum wall thickness and 7 ft. (84 in.) minimum length, which is available from DX Engineering; part number DXE-VGMT-3CG. A customer supplied 2-1/2 in. Schedule 80 pipe that has an outside diameter of 2.875 in. is also suitable. About 36 in. of the mounting pipe should extend above the concrete. Depth of the mounting hole and amount of concrete is dependent on local soil type, condition and antenna guying. Note: For additional information, please look at the files under the "Documentation" tab. Designed to the highest of standards, DX Engineering 80 Meter Self Supporting Heavy Duty Vertical Antennas are very affordable, and could very well be the finest 80 meter antenna you will ever own.
( 9 )
$1,534.98
Momobeam PENTA10 Five Band HF Yagi Antennas
Momobeam PENTA10 Five Band HF Yagi Antennas are popular multiband antennas designed with a compact footprint while delivering full size performance across the 10, 12, 15, 17, and 20 meter bands—all through a single coaxial feed line. Their full size elements provide performance far superior to older multiband designs, and the carefully optimized element spacing—developed using advanced simulation software—ensures exceptional gain, directivity, and on air results. Built on a robust square boom, these antennas offer long term durability, perfect element alignment, and a clean, professional appearance. Assembly is exceptionally straightforward thanks to clearly labeled hardware, telescoping aluminum tubing, and the organized packaging that characterizes all MOMOBEAM products. Each PENTA10 includes an assembly tool and spare parts to support smooth deployment. The high quality 3kW RF choke balun, supplied as standard even though many manufacturers treat it as an optional upgrade, ensures efficient, trouble free operation. With their compact dimensions, superior engineering, and user friendly assembly, Momobeam PENTA10 Five Band HF Yagi Antennas are the ideal choice for operators seeking outstanding performance along with simple, intuitive installation.
Not Yet Reviewed
$1,929.99
EAntenna HF Rotatable Antennas
EAntenna HF Rotatable Antennas include a comprehensive range of mono-band and multi-band Yagi beams and rotatable Delta Loops and Dipoles. Find the band coverage and performance antenna of your dreams right here. For example, the exciting EAntenna 59+ provides great performance on 20, 17, 15, 12 and 10 meters! Check out the specs on this great line of HF directional antennas. DX Engineering offers EAntenna because their attention to manufacturing detail is excellent! Their Yagi, log periodic, and rotatable dipole antennas are built with high-quality stainless steel hardware and aircraft-grade aluminum. As you look through these selections, be aware that advanced, cutting-edge computer modeling and optimization techniques were used to produce every one of the EAntenna premier HF beam antennas and state-of-the-art VHF and UHF Yagi antennas. Their mechanical designs are very robust in every way, as most are rated for at least 100 mph wind survival. To see additional information about each antenna, click on the "More Details" link on the antenna of interest. Then click the Specifications tab to see all of the physical and electrical characteristics of that antenna. EAntenna products are offered exclusively in North America by DX Engineering. Plus, we can ship these great antennas internationally! When you're making plans for a new antenna at your station, look no further for the outstanding solutions by EAntenna, "The Best Choice for Your Antenna System!" NOTE: Manuals are normally supplied bilingual. If your manual lacks an English section, contact DX Engineering for an English version.
( 47 )
$1,729.99
—
$1,859.99
Hamplus Antenna Control Switching Devices
Hamplus Antenna Control Switching Devices include automatic band data controlled remote antenna switching systems including full web remote capability without a PC. Hamplus automates HF + 50 MHz switching for 8 to 16 antennas and from 2 to 8 radios, including devices to connect multiple directional controllers to as many as 8 different antenna rotators. Band-data and frequency reading, multi-function control consoles include support for all major brand transceivers with radio specific control cables. Hamplus also offers manual multi-port to multi-radio antenna switches and a four-stack antenna switching system. Years of Amateur Radio and professional experience shows in these components for emerging and elite DXers as well as established multi-radio contest stations. Hamplus products will improve the function and performance of your station. Click on each part number for specific descriptions, specifications, more information and links to compatible or required products.
( 11 )
$1,542.74
—
$1,688.99
DX Engineering Receive Four Square Array V3 Systems
DX Engineering Receive Four Square Array V3 Systems, DXE-R4S-SYS-V3, dramatically improve reception of weak distant MW and SW signals with excellent rejection of extraneous signals and noise. This is a four-direction switchable phased array that is able to cover multiple HF Amateur bands, such as 160, 80 and 40 meters, by using time delay phasing of four physically short active receive vertical elements. The resulting directional receiving pattern has deep back and side nulls that are superior to Beverage antennas and other receive arrays. The DX Engineering Receive Four Square Array is less susceptible to high angle signals than EWE, Flag, Pennant, K9AY and SAL antennas. Short vertical element receive arrays limit interfering signals and noise for dramatically superior weak signal reception, as compared to full size transmitting antennas and arrays. With the appropriate location and spacing of the four stealthy 8.5 ft. (2.6m) vertical elements, the Receive Four Square Array V3 System is a high performance, directional receive antenna for HF Amateur, SWL or AM DXing. Click or tap the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. DX Engineering Receive Four Square Arrays offer directional performance comparable to four long Beverage wire antennas, while using far less land area. In the appropriate clear area, away from metal, structures and other antennas, each of the four Actives simply mount inches above the earth onto a ground rod. Each element is installed on the corners of the array square with sides that are one-eighth to one-quarter wavelength on the lowest band. For example, the optimized Receive Four Square Array for 160, 80 and 40 meters has elements spaced 70 ft. apart. The DXE-R4S-SYS-V3 system includes the DXE-RFS-3 Receive Four Square Array Controller, four Receive Short Element Active Vertical Antennas, DXE-RSEAV-1, featuring the new DXE-AVA-3 Active Matching Units, insulating mounting plates and stainless hardware. These Active Antennas are packed in a 38 x 5 x 5 in. carton for lower shipping cost. Three sections of 3 ft. aluminum tubing, 0.500, 0.375 and 0.250 inch OD, assemble to a height of only 8.5 ft., so each self-supporting element is truly stealthy. This complete array system also includes the DXE-EC-4 Directional Control Console, one 1,000 ft. roll of quality RG6U cable, all cable prep tools, connectors and hardware for construction of the array. Required ground rods and control cable are purchased separately. Build an exceptionally effective, electronically rotatable, stationary receive antenna that lets you hear the DX signals that cannot be heard on a transmit antenna. Dig the weak signals out of the noise with an antenna that can help make your station one of the best. Order and install the DX Engineering Receive Four Square Array V3 System.
Not Yet Reviewed
$1,929.39
InnovAntennas 50MHz 9-Element LFA-KW Yagi
InnovAntenna 50MHz 9-Element LFA-KW HD Yagi is a giant. This 49 ft. long boom, low noise Loop Fed Array model achieves the Lowest Ever Noise Figure! The G0KSC LFA Yagi is a major step forward in the development of the Yagi Antenna, providing a low noise "front-end" for any advanced 50 MHz radio to easily hear weak signals. This amazing 9 element LFA provides stunning performance across the 50.0 – 50.4 MHz weak signal section of the 6m band. This antenna is hard to beat with a direct-feed 50 Ohm feedpoint, no matching losses and suppression of unwanted noise. EME reviews on the Internet confirm that this 9 element LFA is an excellent antenna. It's very highly suppressed side lobes in both H and E planes make this model ideal for very noisy city locations. For the 6 meter enthusiast who wants to beat the noise AND enjoy maximum gain and front-to-back performance, THIS is the 50 MHz Yagi for you.
Not Yet Reviewed
$2,000.00
Momobeam TRI7 20/15/10 Meter Tri-Band Yagi Antennas
Momobeam TRI7 20/15/10 Meter Tri-Band Yagi Antennas are compact, high performance antenna systems engineered for operators seeking exceptional results on 20, 15, and 10 meters while using a single coaxial feed. These antennas are designed to deliver strong, reliable communication performance in a small footprint, making them ideal for both limited space installations and full size stations. On 20 and 15 meters, the antennas utilize a full size reflector/driver configuration that offers performance far beyond older generation designs, providing improved forward gain, cleaner patterns, and excellent band coverage. On 10 meters, they incorporate a three element system—reflector, driver, and director—optimized with advanced simulation software to achieve maximum efficiency and predictable behavior across the band. Assembly is fast and stress free, requiring no calibration or band specific adjustments such as choosing between CW or SSB during installation. With an SWR consistently under 1.5:1 across all operating bands, these antennas are fully compatible with modern transceivers and linear amplifiers, ensuring stable operation even at high power levels. Each unit includes a complete set of accessories, such as an assembly tool, spare hardware, and a robust 3kW RF choke balun—a valuable component that many competing manufacturers sell separately. The square boom construction and clearly labeled aluminum parts, each organized in separate bags, ensure intuitive and error free assembly from start to finish. With only a single coaxial cable required and compatibility with medium/light duty rotators, the TRI7 antennas combine simplicity, advanced engineering, and excellent build quality, making them an outstanding choice for Amateur Radio operators who want maximum performance with minimal installation effort. Optional configurations, including separate feed versions (MOO TRI7101520SF), offer additional flexibility for operators who prefer independent band feeds.
Not Yet Reviewed
$1,556.99
DX Engineering 2 x 8 Remote Antenna Smart Two Radio Switch System
DX Engineering 2 x 8 Remote Antenna Smart Two Radio Switch System, model DXE-RRMX2X8, is a packaged combination of one DXE-RR2X8B Two-Radio, Eight Port Remote Switch, one DXE-MX2X8 Interface Unit and two DXE-CC-8A Control Consoles. Each control console (A and B) can select one of 7 or 8 positions available. When one console has one particular position selected, the other console is locked out of that position - first come, first served. Providing manual SO2R functionality for two-radio selection of eight antenna systems from 100 kHz through 54 MHz, the DXE-RRMX2X8 Smart System offers virtually no loss across HF and excellent low-loss performance on six meters (less than 0.16 dB of loss at 50 MHz). The RR2X8 dual star-pattern arrangement of 24 internal relays achieves vastly improved port-to-port isolation, very low SWR and excellent power handling over conventional remote coax switches, providing connection of eight SO-239 antenna output ports to either the A (master) or B (slave) SO-239 input ports. The DXE-RRMX2X8 system also uses removable screw terminal plugs for the control cables. The removable plugs greatly simplify installation by eliminating the need for soldering. Disassembly is not required for control wiring access. The DXE-RRMX2X8B also offers the following features: * RF Shielded Weatherproof Housings - unique protection * Excellent Port-to-Port Isolation; typically greater than 70 dB at 30 MHz * Ports not selected are grounded * High-RF tolerant UHF connectors * Enclosed 16 ampere RF relays * Safe 12 volt DC relay operation * MOVs for surge protection on control lines * RF bypass capacitors * Includes two DXE-SSVC-2P Stainless Steel V-Clamps for mounting * The DXE-MX2X8 interface unit interfaces between the DXE-RR2X8 and the two DXE-CC-8A control consoles for seamless operation Each of the two DXE-CC-8A Control Consoles require 12V DC nominal input, have LED port selection indicators and provide the BCD outputs to the DXE-MX2X8 interface unit. Specifications of the DXE-RRMX2X8 2 x 8 Remote Antenna Smart Two Radio Switch System: * Frequency Coverage: 100 kHz to 54 MHz * Power Rating: 6 kW ICAS all modes, 4 kW CCS all modes, under 2:1 SWR * Control Voltage: 10-14V DC at 100 mA per port * Port-to-Port Isolation: >70 dB below 30 MHz, >60 dB below 60 MHz * Ports Not Selected: Are Grounded * Loss: <0.3 dBm below at 52 MHz * Impedance: 50 ohms * Control Cable Requirement: Two ten conductor cables (DXE-CW9S) * Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
( 1 )
$1,534.96
Momobeam DUO7 12/17 Dual Band HF Yagi Antennas
Momobeam DUO7 12/17 Dual Band HF Yagi Antennas are compact dual-band Yagi antenna designed for the 17-Meter (18MHZ) and 12-Meter (24MHZ) WARC bands, offering full-size elements and optimized spacing achieved through advanced simulation software. DUO7 12/17 delivers high performance with low SWR across both operating bands, making it compatible with modern transceivers and linear amplifiers. Assembly is straightforward, with all components clearly labeled and packaged for ease of use. The antenna features a square boom design and requires only a single coaxial cable and is suited for use with a medium-load rotators.
Not Yet Reviewed
$1,809.90
Momobeam Mono5-10 Monoband Yagi Antennas
Momobeam Mono5-10 Monoband Yagi Antennas are 5 element OWA (Optimized Wideband Antenna) Yagi antennas designed to deliver low SWR and a stable 50 ohm impedance across the 28 MHz band, making them a traditional, reliable choice for 10 meter operation. These antennas are factory pre calibrated, requiring no additional tuning, and they provide smooth coverage of the entire operating band with excellent front to back performance, a flat SWR curve under 1.5:1, and impressive gain. Built on a durable square boom, the MONO5 10 antennas include an assembly tool along with spare bolts and aluminum tubing, and all components are clearly labeled to ensure quick, straightforward assembly. Mono5-10 antennas can be mast mounted or side mounted on towers and require a medium duty rotator for proper operation. A 3kW RF choke balun is included as standard equipment—an essential component that many manufacturers offer only as an optional upgrade. Momobeam RF Chokes are built using high quality, low loss, double shielded coaxial cable with a Teflon dielectric, combined with carefully selected ferrite material sleeved over the cable. Together, these elements create a high impedance path for RF, providing excellent isolation between the antenna and the coaxial feedline.
Not Yet Reviewed
$1,507.99
DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas
DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas are high-performance antennas specifically designed for use on Top Band. You will achieve the strongest possible presence at your power level and be competitive with a 160 meter vertical monoband antenna that is only 55 feet tall! A custom-designed capacity hat system allows you to get on 160 meters with unparalleled performance. Wires and ropes have been accentuated in our product image for your viewing clarity. They are much less visible in an actual installation with minimal visual impact for such a large antenna. DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas are tunable with an impressive 40 kHz bandwidth. This means that operation on the CW DX frequencies and DX Phone frequencies are within the range of most internal tuners - no physical changes to the antenna are necessary. DX Engineering DXE-160VA-1, made with sectional aluminum tubing, is a 55-foot high Monoband Vertical Antenna system with a massive 3-inch OD base section. Included with this antenna system is a rugged, patented* stainless steel pivot fixture for ease of raising, lowering and tuning adjustments. Engineered with 6061-T8 and 6063-T832 corrosion-resistant aluminum tubing, stainless steel mounting brackets and stainless steel hardware, this antenna is very durable and attractive. Why Does This Antenna Perform So Well for Its Height? The top capacity hat is large enough that the current along the radiator is almost constant. Typical shortened verticals for this band, with smaller top-hats, have currents that vary along the length and end up producing much less signal strength. This also works in the receive mode to let you hear weaker signals, although at this frequency range dedicated receiving antennas are almost a must. See DX Engineering's full line of Receive Antennas and Array Systems. DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas feature: * High Efficiency Design * 5 kW SSB and CW rated * Unparalleled reliability * Custom designed capacity hat engineered for top performance * DX Engineering Adjustable Matching Network configures the lowest SWR * Broad 2:1 SWR bandwidth - 40 kHz - CW + DX Phone * Lowest possible take-off angle reduces domestic QRM signals * Easy tilt up and down-- Unique fold-over antenna mount features DX Engineering's patented pivoting fixture, *U.S. Patent Number 8,130,168 * High power handling and high strength, UV protected EXTREN® insulators * Ultra-rugged construction starts with 3 inch OD Aircraft Grade heavy wall tubing * Withstands steady-state winds in excess of 50 mph The optional DXE-VRW-1 Manual Winch for easy one-person raising and lowering of the antenna is available from DX Engineering. You can move the DXE-VRW-1 winch between similar antennas in a multi-antenna installation. This antenna system requires the installation of a heavy duty mounting pipe set in concrete. Specifically, 3 in. OD high strength galvanized steel tubing with 0.250 in. minimum wall thickness and 7 ft. (84 in.) minimum length, which is available from DX Engineering; part number DXE-VGMT-3CG. A customer supplied 2-1/2 in. Schedule 80 pipe that has an outside diameter of 2.875 in. is also suitable. About 36 in. of the mounting pipe should extend above the concrete. Depth of the mounting hole and amount of concrete is dependent on local soil type, condition and antenna guying. THUNDERBOLT® Vertical Antennas require a good ground radial system. We recommend a minimum of 32 radials, 65 ft. long, but more radials that are all longer will be more efficient for better signals. Note: For additional information, please look at the files under the "Documentation" tab. Do you want a great Top Band signal? If so, then try one of these DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas!
( 2 )
$1,664.97
DX Engineering Skylark Dual-Band Yagi Antennas
DX Engineering Skylark™ Dual-Band Yagi Antennas cover 17 and 12 meters and have no moving parts, support instant band changes, have no UV challenges, and no antenna-related lightning issues! Skylark™ antennas require no tuning and offer an SWR of less than 1.3:1 over the entire width of both bands. DX Engineering's Skylark™ utilizes aluminum and stainless steel construction, operate from a single feed line, and have a 90 mph wind survival rating. At only 38 lbs., Skylark™ antennas are light enough to be easily installed. These antennas are supplied complete with all mounting hardware for a 2 in. mast. Their stainless steel U-bolts and unique boom to mast mounting system make for very easy installation. Check these DX Engineering Skylark™ features: * Gain on 17 meters: 7.95 dBi * Gain on 12 meters: 7.75 dBi * Front to back on 17 meters: 21 dB * Front to back on 12 meters: 24 dB * 16 ft. boom * Wind loading: 6.5 square feet * Longest element is 27 ft., 8 in. * Turning radius is 16 ft. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. These Skylark™ antennas are a perfect match for stacking with any classic tri-bander. Your tri-bander would support 20, 15, and 10 meters, while the Skylark™ adds 17 and 12 meters. They are also a perfect companion for DX Engineering Skyhawk™ Tri-Band Yagi Antennas. Whatever antenna your tower currently supports, one of these DX Engineering Skylark™ Dual-Band Yagis from DX Engineering will be a worthwhile addition to your antenna farm!
Not Yet Reviewed
$1,999.98
Bushcomm BBA-600VE Multi-Wire Broadband Dipole Antennas
Bushcomm BBA-600VE Multi-Wire Broadband Dipole Antennas are in their flagship antenna group (BBA Series) and all-round best performers. These antennas are highly efficient and engineered to meet the exacting standards of professional users. Frequency range is specified according to useful gain (not only VSWR), and all components are validated for rated power. Bushcomm BBA Series Antennas have the flexibility to suit a wide range of installation situations - between two purpose built towers, in an inverted "V" configuration or even between a tree and the shed out back. All BBA Series antennas include a purpose-designed balun. BBA-600VE specifications: * Frequency Range 1.8 - 30MHz * Nominal Input Impedance 50 Ohm * VSWR (typical) Better than 2:1 * Gain (height dependent) 5dBi (typical) -6dBi at 1.8MHz (typical, 130 ft. height) * Power Rating 250W continuous 600W PEP (voice) * Input connector UHF Type socket (SO-239) * Operating Temperature -22 degrees F to 122 degrees F * Storage Temperature -40 degrees F to 185 degrees F * Shipping 55 x 6.7 x 4 in., approximately 17 lbs. * Antenna Length 177 ft. * Radiating elements 0.079 in. (14AWG) Stainless Steel (304) * Wind rating 130mph (horizontal) * Ice loading 0.25 in., (with reduced wind rating) * Mast Spacing 183 ft. horizontal tower spacing; 131 ft. footprint inverted V Note: When the "Documentation" tab is available, please look at the associated files for additional product information. Light yet sturdy construction ensures low total mass and wind loading. The highest quality materials are used in construction, such as stainless steel wire and fittings, and UV resistant fiberglass rods, to produce an antenna that will survive the rigors of the outdoors for many years. For an ultimate broadband dipole, remember these Bushcomm BBA-600VE Multi-Wire Broadband Dipole Antennas from DX Engineering.
Not Yet Reviewed
$1,612.99
Hustler Heavy-Duty HD9 Series Base Vertical Antennas
Hustler Heavy-Duty HD9 Series Base Vertical Antennas are ideal for applications that call for extraordinary reliability and are suitable for the most difficult environments, remote locations, or tall tower installations. A 1.9 in. diameter, white, extruded fiberglass, weatherproof enclosure combined with a heavy wall (0.225 in.) aluminum base that provides vertical rigidity in winds up 130 mph. The weatherproof sealed Type N female connector includes removable drain plugs and O-rings to allow proper drainage of internal condensation in the upright or inverted position. The Hustler HD9 offset radiator design features phased 1/2 wave radiators which yield precise radiation angle control and very wide bandwidth, made of copper to minimize the possibility of intermodulation. The heavy-duty radiating elements and feed system allow a maximum power of 400 watts. Built-in lightning protection connected to a 0.2 in. diameter copper tube runs the length of the antenna for grounding to the support structure. It includes high-quality, rigid, galvanized steel mounting clamps to prevent ratcheting or twisting of the antenna in high winds. The mounting clamps will accept masts from 1.5 in. to 3.25 in. diameter, or angle members up to 2.5 in. per side. Hustler Heavy-Duty HD9 Series Base Vertical Antennas specifications: * Frequency range: 430 to 450 MHz * Gain: 9 dBd (11.15 dBi) * Bandwidth: 20 MHz * V.S.W.R.: 1.5:1 * Polarization: Vertical * Power rating: 400 watts maximum * Termination: Type N Female * Vertical aperture (3 dB from maximum): 7 degrees * Weight: 13.70 lb. * Wind load (lateral thrust at 100 mph): 92 lbs. * Wind area (flat plate equivalent): 1.3 sq. ft. (0.12 sq. m.) * Maximum wind speed: 130 mph * Feed lines: Copper * Radiators: Copper * Fiberglass enclosure color: White * Mounting: Top or side mount * Galvanized steel mounting clamps accept support pipes up to 3.25 in. O.D. * Lightning protection: Direct ground
Not Yet Reviewed
$1,994.99
Momobeam DUO9 10/15 Dual Band HF Yagi Antennas
Momobeam DUO9 10/15 Dual Band HF Yagi Antennas offers extraordinary performance on the 15-meter (21MHz) and 10-meter (28MHz) bands. Featuring full size elements, exceptional gain, and a high front-to-back ratio, the DUO9 10/15 delivers a sharp radiation pattern ideal for DXing and contesting. DUO9 10/15 is simple to assemble, requires a single coaxial cable, and does not need any calibration. It features low SWR on all operating bands and is a perfect fit for modern transceivers and linear amplifiers. It is the perfect companion for a 20-meter monoband antenna. Assembly is simple and intuitive – DUO9 10/15 uses a square boom, and all hardware is supplied in separate, labeled bags. Additionally, all aluminum tubes are labeled to make assembly quick and easy.
Not Yet Reviewed
$1,919.99
Momobeam Mono4-17 Monoband Yagi Antennas
Momobeam Mono4-17 Monoband Yagi Antennas are full size, four element Yagi antennas designed to deliver excellent SWR bandwidth, optimal gain, and impressive front to back performance. These antennas remain lightweight for effortless handling while offering the strength needed to withstand harsh weather conditions. Built on a square boom, they are supplied with an assembly tool, spare hardware components, and clearly labeled bolts and aluminum tubes to ensure fast and intuitive assembly. All hardware is packaged in separate, clearly marked bags for added convenience. Mono4-17 can be mounted on a mast or side mounted on towers and require a medium duty rotator. A 3kW RF choke balun is included as standard equipment—an essential component that many manufacturers offer only as an optional upgrade. Momobeam RF Chokes are built using high quality, low loss, double shielded coaxial cable with a Teflon dielectric, combined with carefully selected ferrite material sleeved over the cable. Together, these elements create a high impedance path for RF, providing excellent isolation between the antenna and the coaxial feedline.
Not Yet Reviewed
$1,569.99