Availability
Preamplifiers
DX Engineering RPA-2 Modular Receive Preamplifiers
DX Engineering RPA-2 Modular Receive Preamplifiers are newly designed versions of the RPA-1 with internal slots for accessory modules. They accommodate the addition of the one optional plug-in module, such as the 75 to 50 ohm Impedance Transformer Module, or the Receiver Guard 5000HD Plug-In Module, or the DX Engineering Clifton Laboratories Z10020 AM Band Filter Module. DXE-RPA-2 preamps have very low internal noise and are optimized for the 300 kHz to 35 MHz range. They help you hear the weakest signals without artificially raising the noise. Meticulous craftsmanship and durable, robust components allow these preamplifiers to withstand high signal levels while providing superior dynamic range and third-order intercept performance that equals or exceeds most receiver and transceiver front-ends. RPA-2 Receive Preamplifiers have key features added, as requested by our tech-oriented customers and enthusiasts: - Internal slot accommodates the optional 75 to 50 ohm Impedance Transformer Module to accomplish typical receive antenna feedline to equipment transitions without losses -Also allows direct connection to 50 ohm receive antenna feedline BNC connectors with no transformer required - Internal slot for DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module – Front-end protection for the RPA-2 - Secure BNC female connectors and receive-system friendly F female connectors remain; both prevent accidental connection to transmitting devices with UHF connectors - A green LED indicates when DC power is present and the preamplifier circuit is engaged. - An ingenious positive-capture threaded-sleeve 2.1 mm power connector that ensures the DC power cannot be accidentally disconnected from the RPA-2. - Alternatively, a simple internal jumper change allows the RPA-2 to be powered by DC on the feedline While many other common preamplifiers suffer from harmonic distortion, RPA-2 Modular Receive Preamplifiers include our exclusive, advanced push-pull design that eliminates harmonic distortion. Their high quiescent current increases their ability to handle strong signals without distortion or overload. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 Vdc input. Please do not use a cheap wall transformer or noisy switching wall-wart to power these top-of-the-line preamplifiers. Indoor installation at the back of the radio is recommended for RPA-2. For those who want to place them in an enclosure at a receive antenna system, a handy internal jumper allows these new units to be powered on the coaxial cable. RPA-2 Receive Preamplifier Specifications: -Input and Output Connectors, female: BNC and F -Frequency Range: 300 kHz to 35 MHz -Gain: 16 dB, +/- 1.5 dB (over entire frequency range) -Output Third Order Intercept: 43 dBm -Noise Figure: 3.5 dB -One dB Compression Point: +26 dBm (400 mW output) -Dynamic Range, IM3: 110 dB or greater (500 Hz bandwidth) -Power Requirement: 12-18 Vdc, 140 mA max. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering RPA-2 Modular Receive Preamplifiers offer superior receiving results on crowded medium wave and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the advanced operational performance of DX Engineering Receive Preamplifiers. You will be able to pull in the weakest signals and snag that rare one, under the most difficult conditions, when you need it the most. Order your DX Engineering RPA-2 today!
( 14 )
$269.99
SSB Electronic Mast-Mount Preamplifiers
SSB Electronic Mast-Mount Preamplifiers are low-noise, band-specific, weatherproof preamplifiers designed for installation near VHF and UHF antennas. Available for the 6 meter, 4 meter (Europe), 2 meter and 70 cm Amateur bands, these preamplifiers are installed in-line, at the antenna. They improve receive performance by amplifying weak signals before feedline loss can reduce them. Powering and Sequencing Most models can be powered remotely through the coaxial cable, and many modern transceivers include a built-in bias-tee for mast-mounted preamplifiers. If the transceiver or transverter system does not provide power, an external bias-tee or remote-feed unit is required. • The DCW-15 and DCW 2004B provide sequencing support. • The DCC-12 does not provide sequencing. • SP series preamplifiers include a built-in RF VOX circuit for safe operations up to 100 watts; for transmit power above 100 watts, PTT control with a sequencer is required. Some models require a direct DC connection (UHF female). • -S series preamplifiers feature lower current signal relays with slightly higher insertion loss. • MHP and MHP-S series preamplifiers versions require sequencer control (see below). Signal Filtering and Switching Built-in helix filters effectively reject out-of-band signals, helping maintain clean receive performance. Real coaxial relays handle transmit/receive switching, resulting in very low insertion loss (except for SP-S series). And each amplifier is carefully calibrated at multiple test stations before packaging. Dual-Band Models Dual-band models include built-in diplexers, so they require only one connection for the multiband antenna and one connection for the station coaxial cable. MHP Series for Demanding Stations The MHP series is designed for demanding operating environments and provides higher gain for weak-signal modes such as Tropo-DX and EME. With maximum transmit power handling of 1500 watts on 6m and 2000 watts on 2m and 70cm, these preamplifiers are well suited for contesting, DX, and EME operation. Important Note for MHP Models Bias-tee power (on the RF coax) is not supported in most MHP Preamplifiers. They must be powered directly using the appropriate cable size for the required distance, and they may only be operated with a correctly wired sequencer, such as the DCW 2004 B Sequence Controller. Transmitting high power without a directly wired sequencer is likely to damage the MHP preamplifier. Housing and Hardware All SSB Electronic Mast-Mount Preamplifiers are supplied in UV-resistant, weatherproof housings with Type N female connectors. Hot-dip galvanized clamps and stainless steel mounting hardware are included. See individual models for band coverage and detailed specifications.
Not Yet Reviewed
$480.99
—
$494.99
SSB Electronic LNA Series Low-Noise Preamplifiers
SSB Electronic LNA Series Low-Noise Preamplifiers are newly developed low-noise receiving amplifiers for the 6m, 2m and 70cm bands, featuring super low noise with high gain, making them ideal for use in EME (moon bounce), MS (meteor scatter), Aurora and tropo-DX operations. High performance is reflected in exceptional IP3 test figures (35dBm, typical), to provide strong signal immunity. Very good rejection of strong signals near and far guarantees interference-free operation, even in the vicinity of other radio transmissions from commercial and broadcast stations as well as mobile carriers. The input circuit of the amplifier is built with high quality components in a chamber construction, optimized for the best noise characteristics. The bandpass at the output of the amplifier ensures very good in-band selection with signals outside the pass band effectively suppressed. The LNA Series Preamplifiers do not have RX/TX relays and are intended for receiving applications. LNA Series Preamplifiers are built in a sturdy tinplate housing, suitable exclusively for indoor applications (Ip41 to DIN EN 60529). Choose between models that have two Type-N female connectors, Type-N Male and Female, and SMA female. These amplifiers can be powered via an external cable or via a coaxial bias tee (remote power supply). The -MA weatherproof variant of the receive-only LNA series is characterized by a robust, IP44-protected housing, allowing the high-quality preamplifier to be mast-mounted close to the antenna using Type-N connectors only. Power is supplied exclusively over the coax. If your receiver does not output 12-15 VDC receive preamplifier power onto the antenna feedline, use the SSB Electronic DCC-5000PRO Bias Tee (remote power inserter).
Not Yet Reviewed
$316.99
—
$494.99
SSB Electronic LNA-5000 50–5000 MHz Wide Band Mast-Mount Preamplifiers
SSB Electronic LNA-5000 50–5000 MHz Wide Band Mast-Mount Preamplifiers increase signal sensitivity for scanners, receivers, and measuring devices. They may also serve as a low-power amplifier or buffer amp. Built with a modern MMIC on a low-loss ceramic microwave substrate, it provides approximately 20 dB gain, a low 2 dB noise figure, excellent large-signal handling with IP3 greater than 30 dBm, and input IP values improved by 20 dB over the previous version. An input amplitude limiter helps protect against electrostatic discharge. The LNA-5000 supports up to 160 mW PEP / 20 dBm output, uses Type-N female connectors, covers 50 to 5000 MHz, and operates from a 10–20 VDC supply either directly through the DC Input UHF female connector or remotely through the RF coax using an optional DCC-5000PRO Bias Tee.
Not Yet Reviewed
$284.99
SSB Electronic LNA-30 Broadband 5 kHz – 30 MHz Low Noise Mast-Mount Preamplifiers
SSB Electronic LNA-30 Broadband 5 kHz – 30 MHz Low Noise Mast-Mount Preamplifiers cover the VLF, LF, and MF range, including the 2200 through 10 meter Amateur bands. Only for receiving applications, the LNA-30 is used to transform a simple wire or small whip antenna into a powerful broadband receiving antenna. This allows, for example, an SDR receiver to be operated in an unfavorable location with limited space and still deliver very good results. A skimmer or The LNA-30 amplifies the signals received by about 20 dB. The operating power can be varied for effect from 12 and 24V, with higher gain achieved at 24V, but the lowest figure at 12V. A very RF quiet, well filtered linear power supply should be used, not a switching power supply, which connects to this mast-mounted preamplifier via a separate coaxial cable; a UHF female handles the power input. The LNA-30 handles the RF separately with Type-N female connectors for antenna and receiver. When power is removed the preamplifier turns of and no signal from the antenna passes, making this an "always on" broadband preamplifier. The LNA-30 may be mounted on masts up to 2.25 in. (58mm), is weatherproof, and should be placed outside, close to the receive antenna. This preamplifier cannot pass RF power and is not suitable for transmitting operations.
Not Yet Reviewed
$429.99