Availability
5 Results Found For "preamp"
QRO.cz RX Preamp and Bias Tee Module Box Combo
This powerful combo from QRO.cz includes the RX Preamp Module Box with a 2N5109 transistor and a Bias Tee Voltage Injector, offering a complete solution for enhancing receive-only antenna systems. The preamp is based on the proven W7IUV design and delivers up to 18dB of gain with a built-in variable attenuator, allowing precise control over signal amplification. A multi-turn potentiometer enables fine-tuning of the transistor bias for optimal linearity and performance. Two onboard relays automatically switch the unit to bypass mode when power is not present. Power can be supplied either directly via an external DC source or through the included bias tee, which injects DC voltage into the coaxial feedline while isolating the radio from DC current. The bias tee simplifies installation by combining RF and DC over a single coaxial cable, making it ideal for powering remote devices like preamps, relays, or antenna switches. Together, these components provide a clean, efficient, and flexible receive system for antennas such as beverages, Double Half Delta Loops, flags, and other popular RX designs.
Not Yet Reviewed
$299.99
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$275.99
—
$464.45
DX Engineering Beverage Antenna System Combos
DX Engineering Beverage Antenna System Combos are single-wire single-direction Beverage antenna feed systems. These combos include DX Engineering's superb receive preamp and the Beverage antenna feedpoint transformer! The included BFS-1 transformer design makes them immune to the strong signal overload and core saturation. The isolated-winding matching transformer significantly increases the signal-to-noise ratio in Beverage and other high-impedance antennas. The included termination resistor is a special 470 ohm, 2 watt, non-inductive resistor that withstands nearby lightning strikes. Also included, the DXE-RPA-2 Modular Receive Preamplifier is the best low noise, receive preamps available… period. It is optimized for the 300 kHz through 35 MHz frequency range with an advanced push-pull amplifier design that eliminates harmonic distortion and it handles strong signals without distortion or overload. The DXE-RPA-2 Modular Preamp features one internal option slot for a plug-in module. Choose from the DXE-RG5000HD-PM Receiver Guard, the DXE-IT-PM 75 to 50 ohm Impedance Transformer, or use a RXFL Filter Adapter and a Receive Filter board for band pass, high pass or low pass filtering. Click "More Detail" for additional information. The "Documentation" tab contains links to associated files. SWLs and Radio Amateurs around the world have come to rely on the exceptional performance of DX Engineering products. Order one of these DX Engineering Beverage Antenna System Combos to get excellent MW and HF reception with your Beverage antenna.. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$385.98
KD9SV Products SV-DXSS DXpedition Receive Antenna Switches
KD9SV Products SV-DXSS DXpedition Receive Antenna Switches are the ultimate unit for the active low-band DXer. They combine their legendary Front End Saver with the 80/160 Variable-Gain Preamp, a Four-Position Receive Antenna Switch and a high-speed Solid State Amplifier Keying Interface, all into one easy-to-use package. Originally designed for DXpeditions, they are sure to be on the wish list of all low-band DXers! DXpedition Switches were built to be connected to transceivers that ARE equipped with receive outputs and inputs, and to the transceiver's amplifier keying line. DXpedition Receive Switches will directly key all late-model RF power amplifiers. They include a heavy-duty relay for receive antenna disconnection and transceiver RX ANT INPUT grounding, giving your transceiver the ultimate in front-end protection. The four-port antenna switch allows you to select from different receive antennas and the variable-gain control adjusts for 10 to 28 dB preamplification with dual-band band-pass filtering. This lets you choose, on the fly, the correct antenna and gain combination for optimal signal-to-noise for changing band propagation conditions. You may also bypass the unit when you are operating on the higher bands or to listen to the low band transmitting antenna. KD9SV DXpedition Receive Antenna Switches include the Front End Saver, with a lightning-fast solid-state amplifier keying system that is full break-in CW (QSK) capable for all modern amplifiers. They can handle legacy amplifier positive DC voltage keying lines up to 500 Vdc at 8 A. However, DXpedition keying circuits will not work with amplifiers that have negative DC voltage keying lines such as the Heathkit SB-200, Yaesu FL2100-B or Collins 30L-1. For these and other negative DC voltage keyed amplifiers, pair these DXpedition Switches with KD9SV Products SV-KR External Keying Relays. Whether you are a DXer, contester, antenna experimenter, or just want easy access to multiple receive antennas, KD9SV Products SV-DXSS DXpedition Receive Antenna Switches will organize your station as never before! Order yours now, exclusively from DX Engineering!
Not Yet Reviewed
$353.99
DX Engineering RTR-2 Modular Receive-Transmit Interfaces
DX Engineering RTR-2 Modular Receive-Transmit Interfaces provide the easiest and safest method for connecting a dedicated receive antenna to an HF transceiver that does not have a separate receive antenna input. Placed inline with the transceiver's antenna connector, the RTR-2 does the job of a 200 watt T/R relay using the amplifier keying line for failsafe protection, so your transmitted energy cannot go to the receive antenna. Three internal Plug-in Module option slots provide added features and protection: * DXE-RPA-2-PM Receive Preamplifier Plug-in Module * DXE-TRI-PM Transmit Receive Interrupter Plug-In Module * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-in Module DX Engineering RTR-2 Modular Receive-Transmit Interfaces allow the standard transceiver owner to enjoy the advantages of separate receive antennas. For the unswitched receive antenna (RX ANT) port on expensive transceivers, the RTR-2 interface also adds inexpensive failsafe protection. The receive antenna line can be opened or grounded with the optional DXE-TRI-PM Interrupter plug-in module. The RTR-2 is a very useful device for many applications, including: * Connection of external receiving antennas to transceivers lacking external antenna ports * T-R antenna switch for older equipment using separate transmitters and receivers * Interfacing antennas to older phasing or noise cancelling systems * Addition of a switchable receive preamplifier to any transceiver or transmitter and receiver combination * Excellent failsafe receiver protection for close-spaced transmit and receive antennas, without performance degradation of diode circuits of other devices. RTR-2 units feature a unique, failsafe connection method that prevents the hot switching and timing errors that are common on other transmit/receive relays. RTR-2 interfaces switch fast enough for partial break-in CW operation. There are many simple applications for the new RTR-2 and now internal modules can add dramatically improved reception of those really weak signals on the crowded HF bands! DX Engineering RTR-2 Modular Receive-Transmit Interfaces enable operators to enjoy improved reception with any low noise receiving antenna system. This shielded enclosure relay system provides a safe method of connecting a receive antenna, such as a Beverage, Active Receive system, or other receiving accessories to your radio. Major features that make the DX Engineering RTR-2 Receive Antenna Interfaces your best choice for a receive T/R system device: * New Status Indicating Color-changing LEDs * Three internal slots for new DX Engineering modules * New Key Line Out connector for Amplifier * New internal jumper for placing DC on the Receive Antenna feedline for Active or Loop receive antennas * Attractive and heavy stainless steel enclosure * 200 watts RF switching capability * Supports CW partial break-in * Main transmit antenna connector is SO-239 (UHF female) * Radio RF connector is SO-239 (UHF female) * Receive antenna input is 75 ohm F connector * Receive outputs are standard 75 ohm Type F connectors * Inputs are 50 ohm BNC or 75 ohm F (Optional transformer module available) * Safe switching--transmit antenna is always connected to transceiver on power-off * Hot switching lockout--disables receive antenna during transmit mode (Optional DXE-TRI-PM can be set to short the RX ANT line) * Versatile--allows inclusion of Optional RF preamplifiers and other plug-in modules * Simple 13.8 Vdc input for all operations An indispensable accessory for the DX enthusiast and useful for any Amateur's shack, DX Engineering RTR-2 Modular Receive-Transmit Interfaces can help you expand and improve your station's antenna connections and the protection of your equipment.
( 12 )
$375.99