Availability
4 Results Found For "75 ohm coax"
Butternut Antenna Replacement Parts
Butternut Antenna Replacement Parts enable you to keep your Butternut antennas performing at their peak. They offer their capacitors, coaxial matches, coils, and many other parts. Whether used for maintenance or for repairs due to unfortunate damage, Butternut can provide the replacement antenna parts that you need. Butternut high performance antennas have been available for decades. Maintain your antenna with genuine Butternut replacement parts from DX Engineering!
( 92 )
$95.99
DX Engineering Receive Feedline Transformers
DX Engineering Receive Feedline Transformers are designed to match your receive antenna 75 ohm output impedance to the nominal 50 ohm input impedance of most receivers. These transformers may be used in almost any receiving application that requires a 75 ohm Type F connection to a 50 ohm BNC connector. These transformers have very low loss (<0.3 dB) and very wide bandwidth, 100 kHz to 30 MHz! Matching the receive antenna or array to the receiver ensures the best possible performance as a result of a system impedance match. *Important! - These Feedline Transformers are Intended to be used on an RF ONLY coax and should NOT be used for power.
( 1 )
$55.99
DX Engineering Receive Feedline Voltage Injectors
DX Engineering Feedline Voltage Injectors, DXE-FVI-1, are high-quality bias-tee devices that place direct current onto a receive antenna system's coaxial cable while preventing DC from reaching the Radio port. These FVI-1 voltage injectors are used to power active accessory devices, such remote relays, switching systems, and preamplifiers. These are the original equipment FVI-1 units provided with single DX Engineering Active Receive Vertical antenna models. Voltage is applied via the 2.1mm power connector to the receive antenna feedline F connector. The RCA phono jack connects to the receiver input with that DC voltage blocked, while passing RF from 100 kHz to 30 MHz. Various RCA phono plug adapters for different RF cable connectors are available in Suggested Parts. Two DXE-FVI-1 feedline voltage injectors may be connected at opposite ends of a feedline to provide DC voltage on the transmission line for your own custom application, keeping the input and output RF devices isolated from the voltage. The included 120V AC 60 Hz wall transformer power supply may be connected to the 2.1mm power connector may to place approximately +12 volts DC on the coaxial cable center conductor, with the coaxial cable shield used as the negative ground return. A different station power supply, 1-16 VDC, may be used with an in-line, 1 Ampere, fast-blow fuse for various devices. DX Engineering feedline voltage injectors are ready for your "DC power on the coax" needs! Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you need to inject a DC voltage onto a 75 ohm coaxial cable used for receiving, remember the DX Engineering Feedline Voltage Injector!
Not Yet Reviewed
$99.99
DX Engineering LPFC-BNC Low Power Feedline Chokes
DX Engineering LPFC-BNC Low Power Feedline Chokes are intended to be placed in line with coaxial cable fed antennas and equipment used for portable operations, including POTA and SOTA activations. The DXE-LPFC-BNC coax wound toroid achieves an amazing common mode impedance (CMI) curve, with an RF choking capability that far exceeds the CMI of 'a-few-beads-on-coax' product that is offered by other suppliers. Actually, these "Low Power" Feedline Chokes can be used in any station that runs less than 250 watts SSB, 100 watts CW or Digital. ________________________________________ DX Engineering Low Power Feedline Chokes features and benefits: - A unique, lightweight form, with clear heat shrink over the choke* - Light enough to hang inline at the feedpoint of any portable HF antenna. - BNC female connectors for easy connection to portable antennas and gear. - Much higher CMI that other portable, low power chokes, especially across the 40 through 6 meter bands. - Frequency range of 1.8 through 54MHz. - RF Power Handling up to 250 watts PEP SSB, 100 watts CW and Digital (at SWR <2:1). - Recommended for general use to isolate either end of a coaxial cable. * Not intended for permanent outdoor use unless mounted inside a weatherproof enclosure. ________________________________________ These chokes are ideal for use at any HF transceiver or receiver antenna connection, portable, mobile or base. In most cases, DXE-LPFC-BNC prevents RFI, stops stray RF and noise on the feedline from getting into the receiver that would cover up weak signals, and improves efficiency of the antenna system. For any station, including POTA and SOTA, mobile and base, DX Engineering Low Power Feedline Chokes keep the RF controlled.
Not Yet Reviewed
$59.99