Availability
Antennas
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 20 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-800DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-800DXA Medium Heavy-Duty Rotator System from DX Engineering.
( 23 )
$659.99
DX Commander MK2 Signature 9 HF Multi-Band Vertical Antennas
DX Commander MK2 Signature 9 HF Multi-Band Vertical Antennas are an updated version of the original Signature 9 system, featuring a redesigned heavy-duty base section and improved support poles. It's important to note the original Signature9 MK1 plates sets do not fit MK2 poles. The heavy-duty, free-standing DX Commander MK2 Signature 9 antenna design is built on the success of the original DX Commander Classic and Signature 12.4 designs. Efficiently resonant on every HF band of operation, featuring wide SWR bandwidth and low take-off angle, the MK2 Signature 9 covers the Amateur bands 40 through 10 meters, with 80 meters available by adding a horizontal Inverted-L wire. DX Commander vertical antennas are based on the same principles as a fan dipole, with several vertical wire elements of various resonant lengths connected to a common feedpoint. The wire elements and support ropes are arranged with spacer plates around the non-conductive fiberglass mast. When installed with an appropriate radial system, the MK2 Signature 9 achieves efficient quarter-wave vertical performance with natural resonance and low SWR on every band, without the need for traps, coils or antenna tuners. Band-hopping DXing and simultaneous multi-band operations are supported. The MK2 Signature 9 antenna is rated at 1500W SSB/CW, 400W FT8 and other digital modes.
Not Yet Reviewed
$692.98
M2 Antennas Satellite Antenna Packages
M2 Antennas Satellite Antenna Packages will let you operate using Amateur satellites and communicate with the International Space Station! M2 Antennas SATPACK #1 is a perfect starter package for anyone interested in using Amateur satellites to make contacts around the world. SATPACK#1 packages include one each of the following: -- EB-144/RK2M Eggbeater 2 Meter CP Omni Antenna -- EB-432/RK70CM Eggbeater 70cm CP Omni Antenna -- CBVHF-UHF59 Cross Boom VHF/UHF Kit -- Mounting hardware Each Eggbeater antenna includes the reflector kit that produces 6 dB of upward gain for a great hemispherical pattern! Plus, SATPACK #1 provides right-hand, circularly polarized signal transmission and reception that is required for the typical uplink/downlink crossband operations using Amateur satellites. ISS (International Space Station) and ARISS contacts are also possible. Add M2 Antennas Satellite Antenna Packages to your satellite-capable radio and open up a new world of Amateur communications. The SATPACK #1 is now available from DX Engineering!
( 12 )
$719.99
Buckmaster OCF Dipole Antennas
Buckmaster OCF Dipole Antennas are made from the best quality materials with a completely potted waterproof balun and no external connectors. They are designed to give you years of trouble-free service! Buckmaster antennas are shipped fully assembled, ready to deploy with no tuning or trimming required. Choose a model with a 300 watt balun or a 3,000 watt balun. Each has a weather protected SO-239 connector. They are offered in three lengths to operate in these bands: - 270 ft. models cover 160, 80/75, 40, 20, 17, 12, 10, 6 meters - 135 ft. models cover 80/75, 40, 20, 17, 12, 10, 6 meters - 68 ft. models cover 40, 20, 10 and 6 meters Classic OCF (Off-Center Fed) antennas, like Buckmaster, typically have the feedpoint at the 2/3 and 1/3 point on the overall half-wave wire antenna. That means one leg is twice as long as the other. They are intended to be installed with the feedpoint at 35 ft. and the ends at about 15 to 25 ft. However, other installations such as a horizontal "flat top" can work very well. A tuner may be required for best SWR. Buckmaster OCF Dipole Antennas are a very simple way to get on the air and work multiple bands… quickly! They are a great choice as a first antenna or as a supplement to others. Order your Buckmaster OCF Dipole from DX Engineering.
( 65 )
$544.00
Create CLP-5130-1N VHF/UHF Log-Periodic Antennas
Create CLP-5130-1N VHF/UHF Log-Periodic Antennas are high-gain, wideband directional beam antennas. Designed for horizontal polarization, they may also be mounted vertically with user-supplied hardware. These antennas are capable of transmitting on all amateur bands from 6-meters through 23-centimeters at 500 watts power! Forward gain from 50 MHz to 1,300 MHz is 10 to 12 dBi, depending on the frequency. They present an SWR of less than 2.0:1 across their entire 1,250 MHz range of operation. They are also suitable for use in scanner listening, VHF/UHF television, FM broadcast, aviation, government communications, and business-band radio. To fully utilize the entire bandwidth of these antennas requires a high-quality feedline, like DXE-400MAX or LMR-600. These log-periodics use a specially shaped aluminum boom that allows for movement of the phasing line. Additionally, distortions in the vertical and horizontal planes have been minimized and adjustment of the element alignment is unnecessary. This results in a more uniform radiation pattern when compared to similar antennas. Create log-periodic antennas are very easy to assemble when compared to other log-periodic designs. Quality is seen everywhere… even the boom-to-mast bracket is made of rugged magnesium alloy. A Type N connector is employed for maximum signal transfer at high UHF frequencies. If you don't have the space or resources to put up several VHF and UHF antennas, Create CLP-5130-1N VHF/UHF Log Periodic Antennas from DX Engineering are truly your one-antenna solution to VHF/UHF operation!
( 7 )
$519.99
DX Engineering RR8B-HP Remote Antenna Switches
DX Engineering RR8B-HP Remote Antenna Switches are RF switches designed to have excellent performance on HF through 6 meters. Using 16 custom, sealed, moisture-resistant relays, these Remote Switches provide the best port-to-port isolation available with reliable, long-term performance. RR8B-HP switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, thereby allowing their use in complex antenna phasing and stacking systems. DX Engineering RR8B-HP switches use a removable screw-terminal control cable plug that greatly simplifies installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting-bracket flange and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. O.D. Features of the RR8B-HP Remote Antenna Switches include: * Fully RF shielded with stainless steel mounting bracket and hardware * Best port-to-port isolation available: Over 70 dB isolation below 30 MHz, Over 55 dB isolation below 60 MHz * Loss: Less than 0.1 dB below 60 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Shorted or open selection of unused antenna ports * Sealed 20 ampere, RF-rated relays * Safe 12V DC relay operation * Lightning protection on control lines * External quick-connect plug for control lines * Reliable operation in extreme-weather conditions Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For reliable operation of multiple antennas through the operation of remote switching, order DX Engineering RR8B-HP Remote Antenna Switches to do the job!
( 5 )
$549.99
Chameleon Antenna MPAS 2.0 with Hybrid Mini Portable HF Antennas
Chameleon Antenna MPAS 2.0 with Hybrid Mini Portable HF Antennas (Modular Portable Antenna System) is a concept allowing the radio operator to configure and deploy the antenna system in a variety of configurations. This new 2.0 version is a complete backpack antenna system that includes the CHA MIL 2.0 whip and the CHA MIL EXT 2.0 and more wire to support a greater range of deployment configurations: Vertical, Horizontal, Sloper, Inverted Vee, Inverted L, NVIS, Balcony, Stationary Vehicle and Man-Pack. The CHA MPAS 2.0 is perfect for Emergency Preparedness and Survival Communication. It is also the antenna for hams that enjoy camping, hiking, biking, or other types of outdoor recreation which require communication gear to be both effective and highly portable. Specifications: Frequency: 160M - 6M (all configurations require a wide-range antenna tuner) Power: 500W SSB or 250W CW. Mounting Configuration: 3/8-24 Thread The antenna system consists of: 1 X CHA HYBRID-Mini Matching Unit 1 X 73' Antenna Wire 1 X 25' Counterpoise Wire 1 X CHA MIL 2.0 (113 in. Length) 1 X CHA MIL EXT 2.0 (105.5 in. Length) 1 X CHA SPIKE 1 X CHA 50' Coax with RFI Choke 1 X CHA MILITARY BACKPACK 2 X 3/8-24 SS Nuts Stainless Steel Hardware NOTE: IT'S IMPORTANT TO WATERPROOF THE CHA MIL EXT 2.0 BEFORE PERMANENT INSTALLATION Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 6 )
$625.00
DX Engineering RR8B-SD Remote Antenna Switches
DX Engineering RR8B-SD Remote Antenna Switches are the highest power handling antenna switches in the DX Engineering RR8 Series. Think of them as Super Duty. They are designed to switch up to 8 coaxial lines in high-power RF systems. RR8B-SD switches use enclosed RF-rated relays with exceptional RF voltage and current capability to provide reliable, long-term performance. DX Engineering RR8B-SD switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, allowing for use in complex antenna phasing and stacking systems. RR8B-SD switches use removable screw-terminal control cable plugs that greatly simplify installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting bracket flange, and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. outside diameter. RR8B-SD Remote Antenna Switches feature: * Fully shielded, high impact thermoplastic enclosure, stainless steel mounting bracket, and hardware * Excellent port isolation; greater than 60 dB at 30 MHz, worst case * Power Rating: Greater than 10 kW in normal amateur operation on all modes when using antennas with less than 2:1 SWR on 30 MHz and below. Greater than 5 kW above 30 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Lightning protection on control lines * Shorted or open selection of unused antenna ports * Custom sealed 30 ampere high-voltage RF relays * Solderless removable plug for easy installation of control line with no disassembly * Safe 12V DC relay operation * Reliable operation in all weather extremes Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For multi-band multi-antenna QRO operation, there is no better remote switch than DX Engineering RR8B-SD Remote Antenna Switches!
( 4 )
$599.99
M2 Antennas 2M12 2 Meter Yagi Antennas
M2 Antennas 2M12 2 Meter Yagi Antennas offer the VHF operator a perfect balance between manageable size, weight and performance for the money. With 12 elements on a 19 ft. 6 in. boom, but weighing only 8 pounds, 2M12 beams offer nearly 15 dBi gain, and are a great choice for accomplished enthusiasts as well as hams new to the world of VHF beams. M2 Antennas 2M12 beams feature the latest computer techniques for optimization of pattern and gain. Their clean patterns allow you to hear more and interfere less. Clean patterns are essential for stacking, and 2M12 beams are ideal for stacking in either polarization. Two 2M12's side by side vertically polarized make a fantastic FM DX tropo package. Four or more 2M12 beams horizontally polarized are perfect for long haul SSB, CW or digital mode tropo DXing, meteor-scatter, or moon bounce. Structurally 2M12 beams are sturdy and clean, requiring no boom support. Their booms are strong, with 1-1/2 in. diameter tubing in the middle, tapering to 1-1/4 in. and 1 in. sections that reduce weight and wind load. Elements are 3/16 in. 6061-T6 aluminum rod mounted through the boom on UV stabilized button insulators. At the heart of 2M12 beams are M2 Antenna's unique Driven Element Modules, with connectors that are O-ring sealed to the CNC machined block and coaxial balun connectors that feature triple O-ring seals. Internal module connections are sealed in a space-age silicone gel that has nearly four times the dielectric strength of air to enhance power handling. Built for the ham who appreciates a great antenna for a reasonable price, M2 Antennas 2M12 2 Meter Yagi Antennas mean superior performance as well as long term electrical and mechanical integrity. Get your M2 beams from DX Engineering today!
( 5 )
$578.99
Alpha Antenna HexTenna Deluxe Multi-Band Rigid Dipole and Vertical Antennas
Alpha Antenna HexTenna Deluxe Multi-Band Rigid Dipole and Vertical Antennas are versatile, resonant, legal limit portable rigid dipole and vertical antenna systems that cover 40 to 2 meters, plus 220 MHz and 440 MHz. Whether you're operating in the field, at home, or during emergency situations, the HexTenna™ provides reliable performance across multiple bands. This deluxe version includes a heavy-duty Surveyor Tripod.
( 1 )
$600.00
M2 Antennas 436CP30 70cm Circularly Polarized Beams
M2 Antennas 436CP30 70cm Circularly Polarized Beams are a practical sized, yet high performance circular polarized antenna with a remarkably clean pattern. The pattern is important in order to match the antenna's noise temperature with modern low noise preamps. This antenna is ideal for satellite work but is also excellent for terrestrial uses like ATV, repeater operation, and long haul tropo DX. These beams feature CNC machined driven element module is O-ring sealed and weather tight for low maintenance and long-term peak performance. Internal connections are encapsulated in a space-age silicone gel that seals out moisture and improves power handling. The 3/16 in. 6061-T6 aluminum rod elements are centered to minimize interaction and maintain good ellipticity. Insulators are UV stabilized and locked in place with stainless keepers. Rugged construction and uncompromising performance for the boom length; that's M2 Antennas 436CP30 70cm Circularly Polarized Beams!
( 7 )
$643.99
InnovAntennas 50MHz 6-Element LFA-MAX Low Noise Yagi
InnovAntenna 50MHz 6-Element LFA-MAX Low-Noise Yagi is about 3 ft. shorter than other 6-element 6 meter beams but has only 0.7dB less forward gain! It offers excellent performance across the important 50.0 – 50.4 MHz weak signal section of the 6m band. Even though this Yagi has boom only 19.16 ft. long, it produces a forward gain of nearly 11.2dBi and an incredible front-to-back of 31.5dB. This Yagi has a Bent Reflector system designed to enhance SWR bandwidth and front-to-back. And it features a direct-feed 50-ohm feedpoint which eliminates matching losses and is ready to weather severe conditions, with an strong square aluminum tubing boom that is 1.57 in. (40mm) by 0.078 in. (2mm) wall thickness. Tapered elements consist of oversized 0.63 inch (16mm) element centers and 0.51-inch (13mm) element end sections, both with 0.078 in. (2mm) wall thickness. Fully insulated elements ensures continuous, high performance in all weather conditions for many years to come. The boom-to-mast bracket accommodates up to a 2-inch (50mm) mast for this horizontally polarized 6-element LFA-MAX Low Noise Yagi antenna. There are a lot of us... aspiring 6-meter hams in the city where noise is a problem, who want a beam with great gain and amazing front-to-back performance. But space and money is tight? The InnovAntennas 6-Element LFA-MAX is ready!
( 1 )
$699.99
M2 Antennas 2MCP14 2 Meter Circularly Polarized Beams
M2 Antennas 2MCP14 2 Meter Circularly Polarized Beams are the right choice for satellite operations with basic light-duty azimuth-elevation rotator systems. They feature a specially configured driven elements and phasing feeder system and are typically assembled to achieve right-hand circular polarization needed for most satellite operations. An optional polarity switch is available. A single feedline is used to connect 2MCP14 antennas to the 2 meter section of the satellite transceiver. A second feedline typically connects a mated 436CP30 70cm Circularly Polarized Beam, mounted at the other end of a cross boom, to the same satellite transceiver. 2MCP14 beams are light, medium performance circularly polarized antenna designed to work across the two meter amateur band. Optimum match and gain are between 144 & 147 MHz for the satellite band. Computer design techniques help keep spurious side lobes low down for optimum signal to noise ratios. This antenna features CNC machined, O-ring and silicone-gel sealed driven element assemblies that are common to all M2 Yagi antennas. They insure years of trouble free performance regardless of weather. M2 Antennas 2MCP14 2 Meter Circularly Polarized Beams are available for your satellite capable system, right here at DX Engineering.
( 6 )
$662.99
DX Commander CLASSIC 2 Plus 80m HF Multi-Band Vertical Antennas
DX Commander CLASSIC 2 Plus 80m HF Multi-Band Vertical Antennas are an excellent choice for DX performance and general operations. Efficiently resonant on every HF band of operation, featuring wide SWR bandwidth and low take-off angle, the CLASSIC 2 Plus 80 covers the Amateur bands 80 to 2 meters* with the exception of 30M as the 30M element is replaced with an 80M element. DX Commander vertical antennas are based on the same principles as a fan dipole, with several vertical wire elements of various resonant lengths connected to a common feedpoint. The wire elements and support ropes are arranged with spacer plates around the non-conductive fiberglass mast. When installed with an appropriate radial system, the CLASSIC 2 achieves efficient quarter-wave vertical performance with natural resonance and low SWR on every band, without the need for traps, coils or antenna tuners. Band-hopping DXing and simultaneous multi-band multiplexed operations are supported. The CLASSIC 2 antenna is rated at 1500W SSB/CW, 400W FT8 and other digital modes.
( 4 )
$536.04
Unified Microsystems BevFlex-4X and BevFlex-4X/Q Reversible Receive Antenna System
Unified Microsystems BevFlex-4X Reversible Receive Antenna System is a very versatile two-direction low band receiving antenna. This is the updated and improved version of the W8GNM revolutionary design that uses only low cost, low loss RG-6 for the elements and the feedline of a Reversible Beverage antenna or Reversible Beverage on Ground antenna. Plus, it uses specially designed transformer units that allow the feedpoint unit to be placed anywhere along the length of the Reversible Beverage or BOG, instead of only at one end or the other. Like for other Beverage antennas, the Elevated Beverage or a Beverage on Ground (BOG), the performance of the reversible BevFlex-4X system depends upon the length of the user supplied RG-6 coax for the antenna element. Also, the versatile BevFlex-4X components may be used to create a two-direction version of any one of these antennas, using a much shorter length of wire for the receiving element: * EWE * Flag * VE3DO Loop BevFlex-4X Systems consist of four components; one Feed Unit, two Terminator Units and one Control Switch Unit. The Feed and Terminal Units are house in NEMA rated enclosures and use stainless steel hardware for maximum weather protection. Do you need enhanced reception in four directions? The BevFlex-4X/Q combines two sets of Terminator and Feed Units with the RAS-4 remote antenna switch to let you hear better in all four quadrants. The BevFlex-4X antennas can be any mix of Beverage, BOG, Flag, EWE, or VE3DO. The included RAS-4 Remote Antenna Switch only requires a single coax and four wire control cable to the shack. NOTE: An in-shack four direction switch control box is not included. Choose a control console from DX Engineering, EA4TX and others, or build your own. Just add RG-6 coax and ground rods! Click "More Details" and the Brochure link at the Documentation tab to see pdf diagrams of all of these two and four-direction BevFlex receive antenna system connections. Depending upon the real estate you have available, the FAQ chart will help you choose the Unified Microsystems BevFlex-4X or BevFlex-4X/Q configuration that fits your property and your low band reception needs!
( 14 )
$649.95
CHAMELEON ANTENNA MPAS 2.0 Portable HF Antennas
CHAMELEON ANTENNA CHA MPAS 2.0 Portable HF Antennas (Modular Portable Antenna System) is a concept allowing the radio operator to configure and deploy the antenna system in a variety of configurations. This new 2.0 version is a complete backpack antenna system that includes the CHA MIL 2.0 whip and the CHA MIL EXT 2.0 and more wire to support a greater range of deployment configurations: Vertical, Horizontal, Sloper, Inverted Vee, Inverted L, NVIS, Balcony, Stationary Vehicle and Man-Pack. The CHA MPAS 2.0 is perfect for Emergency Preparedness and Survival Communication. It is also the antenna for hams that enjoy camping, hiking, biking or other types of outdoor recreation which require communication gear to be both effective and highly portable. Specifications: Frequency: 160M - 6M (all configurations require a wide range antenna tuner) Power: 100W SSB or 50W CW. Mounting Configuration: 3/8-24 Thread The antenna system consists of: 1 X CHA HYBRID-MICRO 1 X 73' Wire 1 X 25' Wire 1 X CHA MIL 2.0 (113 in. Length) 1 X CHA MIL EXT 2.0 (105.5 in. Length) 1 X CHA SPIKE 1 X CHA 50' Coax with RFI Choke 1 X CHA MILITARY BACKPACK 2 X 3/8-24 SS Nuts Stainless Steel Hardware NOTE: IT'S IMPORTANT TO WATERPROOF THE CHA MIL EXT 2.0 BEFORE PERMANENT INSTALLATION
( 44 )
$600.00
QRO.cz RX AuditePRE SDR Antenna Switch Controllers
QRO.cz RX AuditePRE SDR Antenna Switch Controllers combine the functionality of a T/R switch, a receive antenna input and a receive splitter with specialized switching, all with RF limiter protection. The transmit/receive (TX/RX) main antenna can be shared with both outputs, transceiver and receiver (SDR) with RF power limiter protection. These versatile devices are perfect for use with a separate SDR receiver for Spectrum Panadapter, WebSDR or as a Skimmer Server to contribute spots to the Reverse Beacon Network (RBN). The RX-AuditePRE features frequency coverage of 100 kHz–60 MHz including 160 through 6 meters with a maximum transmit power handling of 200W and a switchable 16 dB preamplifier. Included in the Package: RX-AuditePre Switch – Assembled and Tested DC Cable – DC barrel connector to stripped and tinned wires
( 4 )
$509.99
ACOM eBox Ethernet Remote Control Devices
ACOM eBox Ethernet Remote Control Devices directly integrate ACOM power amplifiers to Ethernet networks for Internet Remote operations. ACOM eBox is specifically designed for use only on ACOM power amplifiers. DX Engineering sells the two versions available, sold with different interface cables: * AOM-EBOX-SS for ACOM 600S, ACOM 700S and ACOM 1200S * AOM-EBOX-2000 for ACOM 2000A with RCU The eBox receives the amplifier's specific commands via Ethernet interface and forwards them to the ACOM amplifier. EASY to OPERATE There is no software to install! The administration of the eBox is done via Web-based programming interface specially developed for ACOM amplifiers. You can use any personal computer running any operating system. You just need to run web browser as Chrome, Opera, Firefox, MS Edge, Safari, etc. ALWAYS UP-TO-DATE Your eBox is always up-to-date due to its integrated function for firmware update. The newest firmware versions are available (usually as *.bin files) at www.acom-bg.com. With just a few clicks you can upload a new firmware to the eBox. ACOM eBox SPECIFICATIONS: * Remote control capabilities via Ethernet * Suitable for use with ACOM 600S, 700S, 1200S and 2000A Power Amplifiers * Web browser-based user-friendly interface NOTE: Included universal 100-240 VAC wall mount power supply with European plug is adapted to North American plug with DMV-EURO-US-PLUG, included in eBox combination models ending in -P.
( 7 )
$749.99
Hustler Base Model G7-144 Vertical Antennas
Hustler Base Model G7-144 Vertical Antennas feature a 7 dBd maximum effective omni-directional gain; providing a consistent pattern, even in marginal areas. Extremely low-angle stacked 5/8 wave radiators deliver superior gain. Due to robust manufacture, harsh environments do not affect their mechanical or signal integrity. They are constructed from high-strength aluminum and employ a fiberglass radome for all-weather durability. Hustler G7-144 antennas are totally self-supporting and are easily assembled. When they are disassembled, their longest section is approximately 4 ft., which makes them easy to handle and move. They are great for EMCOMM and Field Day, or use one for your QTH or repeater service. When it comes to your signal, a good antenna is a must! Order Hustler Base Model G7-144 Vertical Antennas and give your signal a good boost!
( 12 )
$519.99
REZ Antenna Systems Ranger 80 II™ HF Portable Antenna Systems
REZ Antenna Systems Ranger 80 II™ HF Portable Antenna Systems includes a complete, high-quality fast deploy portable antenna that is easily tuned for 80 through 15 meter operations. Perfect for POTA and SOTA activations and any other portable use, this system includes a best-in-class base-load tuning coil and a 9.3 ft. (17 in. folded) stealth black 7-section tapered military whip. Also included, is a premium laser cut water-resistant MOLLE backpack, available in four colors. These amazing backpacks, also available separately, have plenty of space for the Ranger 80 precision-made antenna components as well as your 100W rig, mic, key, coax, battery and laptop. The heart of the REZ Antenna Systems Ranger 80 II™ HF Portable Antenna Systems is the super rugged base-loaded adjustable tuning coil that is 'hands down' the best on the market. Made with CNC machined parts from premium materials, the Delrin body, black anodized 6061 aluminum base and top with all stainless steel hardware makes the Ranger 80 II™ ready to take on any environment, any time. Its unique manually tuned sliding coil tap collar features a large contact area for worry-free power handling of 200W SSB/CW and 100W Digital (at 50% duty cycle). Along with its handy SO-239 connector, the heavy-duty coil base comes with the updated integrated radial ports, improved weather resistance, and will accept up to eight 4mm banana plugs for fast, secure radial wire connections—no fumbling, just plug in and get on the air. The four included quick-deploy 33-foot 18 gauge radials are quickly connected with 4mm banana plugs. Additional radial sets are available separately. Base and whip connections are standard 3/8-24-inch thread for interchangeability with other brand accessories.
Not Yet Reviewed
$634.00
—
$668.99
Chameleon Antenna PRV Portable Resonant Vertical Antennas
Chameleon PRV Portable Resonant Vertical Antennas are lightweight and rugged antenna systems intended for extreme portable use, such as Parks On the Air (POTA), Summits On the Air (SOTA) and other outdoor operation where an efficient but highly portable antenna is required. In addition, it is perfect for RV, apartment or condominium use, where a small balcony or patio may impose space limitations. Adjusting the height of the Multi-Configuration Coil (MCC) and installing the appropriate number of counterpoise wires for the desired band allows for easy band selection, enabling operation on the 40-10 meter Amateur Radio bands without an external tuner. Operation on 6 and 2 meters requires further adjustments to the telescoping whip length, along with adjusting the Multi-Configuration Coil (MCC) and proper counterpoise selection. Available in 2 configurations to complement your operating style, the PRV-SOTA (Light Kit) and PRV-POTA (Heavy Kit), which contains all the components of the PRV-SOTA (Light Kit) with the addition of a Universal Clamp Mount and a set of two 12 inch Extender Rods to elevate the base of the antenna for improved performance. The PRV-SOTA and PRV-POTA are extremely modular antenna systems with the ability to use components and accessories from other popular Chameleon antennas such as the Modular Portable Antenna System (MPAS 2.0) and MPAS Lite antenna.
( 2 )
$569.00
—
$674.00
InnovAntennas VHF UHF Plus Log Periodic Dipole Array Antennas
InnovAntennas VHF UHF Plus Log Periodic Dipole Array Antennas are specifically designed to serve in a wide range of Amateur, industrial and commercial radio applications. Two frequency coverage models feature: - Broadband frequency coverage with good directionality - Horizontal or Vertical Polarization Mounting - Gain and front-to-back performance for specific purposes as compared to Omni-directional zero-gain Discone - RF Power Handling up to 1000 watts - Boom End Mount max. 2 in. (50 mm) mast - Computer-optimized 50 ohm feedpoint design for direct coaxial cable connection - Robust construction with high-quality materials InnovAntenna Log-Periodic Antennas offer state-of-the-art technology and quality along with impressive versatility and reliability. Achieve performance and efficiency for your specialized radio applications.
Not Yet Reviewed
$579.99
DX Engineering 4030VA-1 Dual-Band THUNDERBOLT® Vertical Antennas
DX Engineering's Dual-Band THUNDERBOLT® 40/30 Meter Vertical Antennas are high performance dual-band pile-up busters that are tunable to operate with an SWR of 1.5:1 or less across both bands. The maximum power rating ensures solid performance, particularly on CW. Plus, the digital modes are popular on 30 meters. The massive EXTREN® channel insulator supporting the rugged structural grade type 6063-T832 drawn aluminum antenna radiator has over twice the tensile and flexural strength of competitive nylon plastic materials, and they are superior for their RF handling characteristics. Designed with rugged 6063 heat-treated, corrosion-resistant aluminum tubing and stainless steel hardware, these antennas are very durable and attractive. Now, you can have full quarter wave performance on both bands without having to compromise. Of course, another key to performance is a good ground radial system. We recommend 32 radials, 32 ft. long. Fewer radials will work, but with diminished results. These antennas include the antenna element, insulated Extren mounting channel, mounting plate, tilt base, stainless steel hardware, and stainless steel element clamps. See Suggested Parts for additional items that will enhance the performance of your installation. DX Engineering's Dual-Band THUNDERBOLT® 40/30 Meter Vertical Antennas feature: * Full band coverage on 40 and 30 meters with SWR under 1.5:1, with no tuner needed * 40m bandwidth greater than 750 kHz with SWR under 2:1 * Tunable above and below 7 MHz range for MARS and CAP frequencies * Over maximum legal power handling * Optimum 30 ft. overall height * Self-supporting design to withstand 60 mph wind without guying Note: For additional information, please look at the files under the "Documentation" tab.
( 2 )
$609.98
Green Heron RT-21-CDE Universal Digital Rotor Controllers
Green Heron RT-21-CDE Universal Digital Rotor Controllers are completely new, extremely advanced and adaptable controllers for your directional antenna rotation systems. Offering the ultimate in operational capabilities, Green Heron RT-21-CDE Universal Digital Rotor Controllers are the best controllers available for your new rotor unit or as a replacement in existing systems. You can add these great features to your existing rotator unit, without even climbing the tower! * Pre-programmed for Hy-Gain and CDE rotator systems * High-visibility LCD display with adjustable backlight brightness * Fully versatile controls for point-and-shoot or manual push button operation plus presets * Automated rotator computer control through RS-232 or USB * PWM (pulse width modulated) variable-speed control * Start and stop ramping to reduce tower and antenna stresses * Precision heading accuracy up to 1/10 degree * Fully supports side mounted antennas, soft limits prevent running into tower * Allows over-travel up to 720 degrees total * Offset control allows center of rotation at any heading, allows N & S center on same mast, and compensates for slipped mast * Fully user-programmable, reversal and brake delay, speed minimum and maximum, limits, ramps, and much more * Master/slave for stacked arrays, turn together or separately * Counter-rotation, install rotor above rotating tower * Easy front panel setup and setup utility software Replace your old-fashioned rotator controller with a modern, state-of-the-art digital controller! Green Heron RT-21-CDE Universal Digital Rotor Controllers from DX Engineering are pre-programmed specifically for Hy-Gain/CDE HAM-series and T2X (Tailtwister) rotators. However, they are easy to setup for all other rotator units because they are field programmable with convenient, internal, solderless jumpers. Get yours today!
( 6 )
$571.12
—
$649.00