Availability
Baluns, Ununs and Chokes
Reduce SWR, RFI, and pattern distortion with our leading-brand Baluns, Ununs, and Chokes! For the proper connection and RF transition from a balanced antenna to an unbalanced...
Reduce SWR, RFI, and pattern distortion with our leading-brand Baluns, Ununs, and Chokes! For the proper connection and RF transition from a balanced antenna to an unbalanced coax our baluns provide excellent common mode rejection and current balance so antennas operate at maximum efficiency and high isolation for minimal noise. Ununs are used for matching an unbalanced antenna to an unbalanced feedline. Feedline chokes keep noise out of the antenna and the receiver to improve overall reception plus they reduce RFI by eliminating feedline radiation. Enjoy maximum power transfer, optimum balance and a lot less noise. Shop...
Reduce SWR, RFI, and pattern distortion with our leading-brand Baluns, Ununs, and Chokes! For the proper connection and RF transition from a balanced antenna to an unbalanced coax our baluns provide excellent common mode rejection and current balance so antennas operate at maximum efficiency and high isolation for minimal noise. Ununs are used for matching an unbalanced antenna to an unbalanced feedline. Feedline chokes keep noise out of the antenna and the receiver to improve overall reception plus they reduce RFI by eliminating feedline radiation. Enjoy maximum power transfer, optimum balance and a lot less noise. Shop for DX Engineering Baluns, Ununs and Feedline Chokes here!
COMTEK Current Feedline Chokes
The updated COMTEK CFC-50A 50 ohm Feedline Chokes consist of 75 heavy-duty mix-31 RF choke beads on a length of RG400 PTFE coax terminated at both ends with silver-plated PTFE PL-259/UHF male connectors and the correct length of heat-shrink tubing. COMTEK Current Feedline Chokes ensure that stray RF does not flow on the outside shield of your feedlines. They are typically installed at the antenna feedpoint connection. They may also be used where a long run of feedline leaves a remote antenna switch or a tower. They are also very effective at the shack end of a long run of on-the-ground or above-ground coaxial feedline, to block unwanted RF signals and noise picked up on the shield. These chokes provide excellent common mode impedance and handle up to 5 kW from 1.8 to 54 MHz. These chokes are assembled except for the tubing needs to be installed and heat-shrinked after the choke is positioned as it will be installed.
( 14 )
$131.49
REZ Antenna Systems XFORM 4:1 UNUN
The REZ Antenna Systems XFORM 4:1 UNUN is a modular impedance-matching system designed for the Scout system, expanding its capabilities beyond traditional quarter-wave verticals and half-wave dipoles. It integrates seamlessly with the Scout XF base and supports legacy Scout bases via a jumper connection. The XFORM enables over 30 potential antenna deployment options when combined with future 9:1 and 49:1 transformer modules, which are currently in development. Built for durability, the XFORM features CNC-machined 6061 aluminum, an acetal polymer body, and stainless steel hardware. Its gasket-sealed design ensures reliable performance in harsh weather conditions. The unit handles up to 200 watts PEP SSB and 75 watts digital (50% duty cycle) and measures 5.5 inches in length with a maximum diameter of 2.5 inches. Each core is precisely wound and tested for thermal stability and minimal insertion loss, delivering efficient signal transfer and cooler operation underload. The XFORM requires a Scout base for use, making it an essential upgrade for operators seeking maximum versatility and performance in portable HF antenna systems.
( 3 )
$189.95
DX Engineering LPFC-BNC Low Power Feedline Chokes
DX Engineering LPFC-BNC Low Power Feedline Chokes are intended to be placed in line with coaxial cable fed antennas and equipment used for portable operations, including POTA and SOTA activations. The DXE-LPFC-BNC coax wound toroid achieves an amazing common mode impedance (CMI) curve, with an RF choking capability that far exceeds the CMI of 'a-few-beads-on-coax' product that is offered by other suppliers. Actually, these "Low Power" Feedline Chokes can be used in any station that runs less than 250 watts SSB, 100 watts CW or Digital. ________________________________________ DX Engineering Low Power Feedline Chokes features and benefits: - A unique, lightweight form, with clear heat shrink over the choke* - Light enough to hang inline at the feedpoint of any portable HF antenna. - BNC female connectors for easy connection to portable antennas and gear. - Much higher CMI that other portable, low power chokes, especially across the 40 through 6 meter bands. - Frequency range of 1.8 through 54MHz. - RF Power Handling up to 250 watts PEP SSB, 100 watts CW and Digital (at SWR <2:1). - Recommended for general use to isolate either end of a coaxial cable. * Not intended for permanent outdoor use unless mounted inside a weatherproof enclosure. ________________________________________ These chokes are ideal for use at any HF transceiver or receiver antenna connection, portable, mobile or base. In most cases, DXE-LPFC-BNC prevents RFI, stops stray RF and noise on the feedline from getting into the receiver that would cover up weak signals, and improves efficiency of the antenna system. For any station, including POTA and SOTA, mobile and base, DX Engineering Low Power Feedline Chokes keep the RF controlled.
Not Yet Reviewed
$59.99
DX Engineering Ferrite Bead Choke Kits
DX Engineering Ferrite Bead Choke Kits, DXE-FBC, provide the components for the simplest and most effective technique of creating RF isolation at an antenna feedpoint or feedline termination. Covering the frequency range 1.8 to 54 MHz, these 40 toroidal mix-31 solid ferrite beads, installed on a user supplied coaxial cable (prior to connector installation*), to build an RF choke with a very high Common Mode Impedance (CMI) over a very wide frequency range. This is the same choke that world-class contest and DX stations install. Given the simplicity and raw performance of this 40-bead choke, its comprehensive RF features and benefits should become familiar to every radio amateur and antenna experimenters. * Yes!, the superior overall performance of the DXE-FBC Ferrite Bead Choke completely offsets the trouble of cutting off a coaxial connector, installing the kit, and then installing a new connector. It really is that good!
( 4 )
$152.99