Availability
Baluns, Ununs and Chokes
Reduce SWR, RFI, and pattern distortion with our leading-brand Baluns, Ununs, and Chokes! For the proper connection and RF transition from a balanced antenna to an unbalanced...
Reduce SWR, RFI, and pattern distortion with our leading-brand Baluns, Ununs, and Chokes! For the proper connection and RF transition from a balanced antenna to an unbalanced coax our baluns provide excellent common mode rejection and current balance so antennas operate at maximum efficiency and high isolation for minimal noise. Ununs are used for matching an unbalanced antenna to an unbalanced feedline. Feedline chokes keep noise out of the antenna and the receiver to improve overall reception plus they reduce RFI by eliminating feedline radiation. Enjoy maximum power transfer, optimum balance and a lot less noise. Shop...
Reduce SWR, RFI, and pattern distortion with our leading-brand Baluns, Ununs, and Chokes! For the proper connection and RF transition from a balanced antenna to an unbalanced coax our baluns provide excellent common mode rejection and current balance so antennas operate at maximum efficiency and high isolation for minimal noise. Ununs are used for matching an unbalanced antenna to an unbalanced feedline. Feedline chokes keep noise out of the antenna and the receiver to improve overall reception plus they reduce RFI by eliminating feedline radiation. Enjoy maximum power transfer, optimum balance and a lot less noise. Shop for DX Engineering Baluns, Ununs and Feedline Chokes here!
Clearance
COMTEK Jerry Sevick W2FMI Series Current Baluns
COMTEK Jerry Sevick W2FMI Series Current Baluns were inspired by the writing of Jerry Sevick, as published in his book "Understanding, Building, and Using Baluns and Ununs" also available from DX Engineering. COMTEK baluns are value-engineered for maximum performance at a reasonable cost. They provide a superb, efficient transition between unbalanced coax and balanced antennas. COMTEK Baluns feature: * Jerry Sevick design with modern improvements from DX Engineering's in-depth balun research and development * Unique high-voltage compensating capacitors for unequaled SWR bandwidth * Outstanding ferrite-mix coated toroid core with special design to accommodate close coupling without excessive stress * Exceptionally high and consistent common mode impedance across the specified bandwidth, which provides isolation where it is needed most * Special wire size selection and Teflon-insulated wire sleeves provide exact impedance matching and superb insulation, unlike common Thermaleze wire * Typical insertion loss is less than 0.2 dB * Power handling on HF is 3 kW CW and 5 kW SSB on single core models, 5 kW CW and 7 kW SSB on dual core models * May be used to 54 MHz with reduced ratings * Gasketed SO-239 connectors are silver plated and have Teflon insulation * Sealed in a weatherproof 4 in. x 4 in. x 2 in. NEMA box * Stainless steel hardware Note: Polarity markings on baluns are used for matching phase on balanced antennas when stacking beams for a phased array. Also, the positive terminal should be connected to a vertical element or Inverted-L and the negative terminal goes to the radials. For most regular applications on one antenna, including beams, dipoles and most wire antennas, balun polarity doesn't matter. The best Amateur Radio baluns in the world are from DX Engineering. That includes COMTEK Jerry Sevick W2FMI Series Current Baluns!
( 10 )
$104.99
—
$129.99
$68.24
—
$84.49
DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes
Introducing DX Engineering "Maxi-Core® 20" Baluns and Feedline Chokes. They reduce or eliminate currents on the outside of your feedline allowing you to hear and to be heard much better. They keep more RFI/BCI out of your antenna and receiver and transfer more of your transmitted signal to the antenna for higher efficiency, the best antenna pattern and maximum performance. Signaling a new era of RF performance across the 1.8 to 54 MHz frequency range, DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes handle full-legal-power-plus and provide higher common mode impedance (CMI) across a greater frequency range than competing models and even previous DX Engineering and Comtek models. Years of R&D coupled with major advancements in test equipment and techniques combined with custom ferrite materials have allowed our engineering team to design the DX Engineering Maxi-Core® 20 Baluns and Feedline Chokes. Maxi-Core® 20 Baluns and Chokes have high CMI across the AM Broadcast band and the HF/6M spectrum, which is essential to provide sufficient suppression of unwanted transmitted and received RFI/BCI current on the feedline shield exterior. Hear and be heard with DXE Maxi-Core® 20 Baluns and Feedline Chokes. Choose superior performance from these models: * DXE-MC20-1-1 Maxi-Core® 20 - 1:1 Current Choke Balun - For all HF-6m balanced antennas with a 50 ohm feedpoint, including resonant dipoles, loops, Yagis, beams, etc. * DXE-MC20-FC Maxi-Core® 20 - 1:1 Feedline Choke – This high CMI line isolator is perfect for use in line on 50 ohm coaxial feedlines, at the antenna, tower or shack end of the feedline. * DXE-MC20-1-1T Maxi-Core® 20 - 1:1 Current Choke Balun – This 1:1 "T" model is for force feeding antennas with a tuner. Use it at the end of ladder line of any impedance or mounted on a coax fed non-resonant antenna. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-C4-1 Maxi-Core® 20 - 4:1 Current Choke Balun is for use on antennas with a 200 ohm feedpoint and at the end of any impedance ladder line, especially on antenna systems with higher impedance. This model tolerates operation at high SWR on non-resonant multi-band antennas. * DXE-MC20-V4-1 Maxi-Core® 20 - 4:1 Voltage Balun is a 200 ohm to 50 ohm transformer for use on random long-wire and OCF antenna applications. This true voltage balun is intentionally designed with low CMI for antennas that need a transformer without RF choking for easier antenna tuner operation and it tolerates elevated SWR. Maxi-Core® 20 Baluns and Feedline Chokes are built into a convenient weather resistant NEMA enclosure that is mounted easily with optional brackets. They feature 1/4-20 stainless steel hardware and a high quality silver-plated PTFE dielectric SO-239 (UHF female) input connector. The SO-239 connector limits power handling to 5 kW at low SWR and reduced power at elevated SWR. These baluns and the feedline choke exhibit very low insertion loss and inherently low SWR. Optional mounting brackets are available for use on wire antennas or for verticals, Yagi and beam antennas. See the Suggested Parts tab after clicking "More Detail" on the model of interest. Combination packages that include balun or choke and mounting bracket are also available.
( 142 )
$141.99
—
$169.99