Availability
HF Beam Antennas
EAntenna HEX6B Six Band Hexbeam Antenna
EAntenna HEX6B Six Band Hexbeam is a directional HF antenna for the six Amateur bands 20, 17, 15, 12, 10 and 6 meters. This design follows the ideas of G3TXQ Steve Hunt, the originator of the Broadband version of the Hex Beam antenna. However, this mechanical construction is a version refined by EAntenna with their long-standing antenna engineering experience. The result is an efficient, lightweight portable antenna for the high HF DX bands, which is ideal for use for DXpeditions and vacations. An installation at 20 ft. above the ground can work quite well, but a tower-mounted Hexbeam at a height of 35 to 60 ft. is known to perform as intended and produce excellent DX results. The HEX6B works as two element beam on each band. Ready-to-use wires and ropes are attached to the fiberglass struts and due to the mechanical tension of the struts, the beam is stretched to its fixed size all the time, so there is no sag on the wires. The radiator dipoles are connected to the vertical center support, with each band wire element attaching with screw clamps. The center support is designed as a coaxial transformer and balun, providing a particularly good match on each band, with one feedline for all six bands. The HEX6B forward gain is approximately 3dBD or better, the front/back ratio is between 13 and 22dB. SWR is 1.5:1 or better on all bands except 10m, where SWR is 2:1 or better. Each band can be used in full bandwidth without a tuner. The maximum allowed power is 5 kW. The fiberglass tubes are double coated against UV radiation. The setup of the HEX6B six band beam is simple and can be done by one person in about 30 minutes. All ropes and wires are ready, cut to length, so no tuning is required. Due to the low weight of only 18.7 lbs. (8.2 kg) this hex beam can be installed on a light aluminum push-up mast. Rotation is either done with a small rotator or by hand. The HEX6B mast clamp accommodates poles with a Diameter from 1.10 -2.05 in. (28-52mm).
( 6 )
$899.99
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles offer high performance multi-band HF operations, and they are an excellent choice where there's not enough space for a full-size dipole or Yagi. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these unique multi-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. DIEX Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles power handling is 1500W PEP SSB, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that a directional HF antenna should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 4 )
$765.99
Diex 3 Element Monoband Full Size Yagi Antennas
Diex 3 Element Monoband Full Size Dipole Antennas are full sized directional antennas covering the 20 through 6-meter amateur bands. Expertly engineered and crafted in Brazil from quality aluminum tubing and durable materials, these antennas are built to endure harsh environments while providing long-lasting, high-performance operation. With a power rating of up to 2000 Watts PEP, these antennas are ready for demanding applications. Offering at least 8 dBi of gain and greater than 500 kHz of bandwidth at less than 2:1 SWR, these monoband antennas will help your signal reach further – whether across the country or around the globe. Designed for efficiency, these 3 Element Monoband will get your signal further and let you chase far away DX.
( 3 )
$849.99
—
$995.99
DX Engineering PS-3B PRO-STACK Three Antenna Phasing Units
DX Engineering PS-3B PRO-STACK Three Antenna Phasing Units offer the ultimate performance for combining three identical Yagi or Log Periodic directional antennas and may be used for vertical antennas in a phased array that cover any band, from 160 through 10 meters. Pro-Stack frequency independent broadband phasing devices operate optimally with three properly spaced mono-band antennas, but can be used with three identical stacked multi-band beam antennas, for pattern and null steering that wins contests and snags the rarest DX! Signals arrive at your antenna system from different azimuth directions and different elevation angles. Adding a stacking phasing system to a rotational array adds the ability to steer the pattern of the antenna array in two planes, azimuth and elevation, and to move the major lobe and nulls. The greatest advantage of Pro-Stack arrays is the ability to move harmful pattern nulls away from signal arrival angles. While gain makes a marginal improvement, moving a 20 to 40 dB null can be a phenomenal change, so the Pro-Stack can make the difference between a barely readable and a strong signal, providing the performance edge needed to work rare DX - and win contests. DXE-PS-3B Pro-Stack Phasing Units are 50 ohm relay systems that handle up to 5 kW. A separate user-supplied automated controller or the optional DX Engineering DXE-EC-PS3 Control Console for these 12-position rotary switch selections: - Three antenna ports in phase, default with no power to control console. - Antenna port 1 only - Antenna port 2 only - Antenna port 3 only - Port 2 out of phase, Port 3 in phase - Port 1 out of phase, Port 3 in phase - Port 1 out of phase, Port 2 in phase - Ports 2 and 3 in phase - Ports 1 and 3 in phase - Ports 1 and 2 in phase - Ports 1 and 2 in phase, Port 3 out of phase - Ports 1 and 3 in phase, Port 2 out of phase - Port 1 out of phase, Ports 2 and 3 in phase These PRO-STACK units may also be used for other applications requiring these feedline selections. To ensure lowest SWR, impedance matching automatically changes when any antenna is disabled. By switching between antennas at different heights above ground and/or changing the phase relationship between multiple antennas. The old standard system in stacks was to activate or disable specific antennas in the stack to change pattern. However, with the Pro-Stack system, gain remains higher when all antennas are driven and phase is changed, plus this system allows phase inversion as well as the ability to switch any single antenna out of the array. DXE-PS-3B Broadband Phasing Units provide the greatest flexibility for three identical antennas. This relay unit contains a broad-bandwidth high-power 2:1 impedance matching transformer. This eliminates common requirements of using mixtures of 75 ohm and 50 ohm phasing or delay cables for impedance matching. Feedlines to each antenna from the relay unit must be the same cable of the same length and match the antenna impedance. DXE-PS-3B Pro-Stack Broadband Three Antenna Phasing Units feature: - Power Handling up to 5 kW - Broad band coverage on 160-10 meters - RF Shielded Weatherproof Housing - unique protection - DXE-PS-3B has High-RF tolerant, silver - PTFE UHF connectors - DXE-PS-3BDIN has Amphenol Connex 7/16 DIN Panel Connectors - DXE-PS-3BN-P are made with high-quality silver-PTFE Type N female connectors - Proven high current DX Engineering RF Relays - Safe 12 volt dc relay operation - MOV surge protection on control lines - RoHS compliant assembly Get a DX Engineering PS-3B PRO-STACK Three Antenna Phasing System for your winning antenna array.
Not Yet Reviewed
$895.99
—
$999.99
InnovAntennas 10M and 6M Yagi Antennas
InnovAntennas 10M and 6M Yagi Antennas are a new series of gain-optimized two-band beams designed with the latest software. They feature a single coax feed system, ideal for modern transceivers with HF plus 6 meters. Different versions of these 28 and 50 MHz Yagi beams are available to suit every station and budget, depending upon boom length and element counts. Interlaced elements allow short and medium-length boom versions that are perfect for stations with limited space, simpler supports and smaller rotators, while the long boom versions satisfy the top enthusiasts. Dedicated to the bands where propagation changes quickly, InnovAntennas 10M and 6M Yagi Antennas offer excellent performance and rugged reliability, to take advantage of every opening.
( 1 )
$829.99
—
$949.99
Hamplus Four Stack II Systems
Hamplus Four Stack II Systems makes it possible to easily and quickly change selections of any in-phase combination of two, three, or four stacked HF beam antennas or an array of HF phased vertical antennas. Plus, Four Stack II Systems can be combined to control antenna selections on any of the array switches by any of the multiple system Control Consoles. This is possible with simple patch cable networking. Up to four operating positions can have access to four different stacked arrays. The Hamplus Four Stack II System provides unprecedented control of your multiple antenna arrays. The 4-Stack Control Console has five illuminated pushbuttons; ANT 1 through 4 select stacked antennas and ENTER aids in programming. Each antenna selection keys works as a one-touch ON, one-touch OFF method, so it is easy to control which of antennas you want to use at a certain time. Trying different combinations of antennas for the transmission and reception can be accomplished independently, quickly and easily. Arrays can be configured differently for receive and transmit without manually switching back and forth. The system is managed and supervised by a microcontroller that has internal software designed to meet the various system functions and easy operation. All control boxes can be interconnected so that any remote console can command any antenna array switch box. The Four Stack II switch box is rugged and capable, with a better design for mounting outdoors, near or under antenna arrays. No extra or special housings are needed. With the internally connected controller cable, the system is an easy, plug-and-play operation. The Four Stack II is available with either Type N female or UHF female (SO-239) connectors for your array. The Four Stack II is rated for 3,000 W maximum RF power and covers 1.8 to 30 MHz. Connection to 50 ohm, low SWR antennas with 50 ohm coaxial cable is required. All combinations of antennas are in-phase only. Achieve complete control of your antenna arrays with Hamplus Four Stack II Stack Systems from DX Engineering!
Not Yet Reviewed
$899.99
Diex 4 Element 10-meter Monoband Full Size Yagi Antennas
Diex 4 Element 10-meter Monoband Full Size Yagi Antennas are full sized directional antennas for the 10-meter amateur band. Expertly engineered and crafted in Brazil from quality aluminum tubing and durable materials, these antennas are built to endure harsh environments while providing long-lasting, high-performance operation. With a power rating of up to 2000 Watts PEP, these antennas are ready for demanding applications. Offering 8.6 dBi of gain and greater than 600 kHz of bandwidth at less than 2:1 SWR, this 10-meter monoband antenna will help your signal reach further – whether across the country or around the globe. Designed for efficiency, this 4 Element Monoband antenna will get your signal further and let you chase far away DX.
Not Yet Reviewed
$799.99
Diex 5 Element 10-meter Monoband Full Size Yagi Antennas
Diex 5 Element 10-meter Monoband Full Size Yagi Antennas are full sized directional antennas for the 10-meter amateur band. Expertly engineered and crafted in Brazil from quality aluminum tubing and durable materials, these antennas are built to endure harsh environments while providing long-lasting, high-performance operation. With a power rating of up to 2000 Watts PEP, these antennas are ready for demanding applications. Offering 9.7 dBi of gain and greater than 800 kHz of bandwidth at less than 2:1 SWR, this 10-meter monoband antenna will help your signal reach further – whether across the country or around the globe. Designed for efficiency, this 4 Element Monoband antenna will get your signal further and let you chase far away DX.
Not Yet Reviewed
$959.99
InnovAntennas Moxon Directional Antennas
InnovAntennas Moxon Directional Antennas are mono-band, two element directional antennas with the ends bent toward each other. The gap between the elements is bridged by a non-conductive rod to give the antenna stability. The result is a directional antenna that is compact and of a relatively simple design, providing directionality and a very good front-to-back ratio. Available in versions for 10/11 Meters, 12 Meters, 15 Meters, 17 Meters, and 20 Meters, these compact antennas are a solution when you require directionality and don't have a lot of room. The InnovAntennas Moxon antennas are rated for up to 7,000 Watts and range from eleven pounds to twenty-two pounds in weight, meaning a small tower or mast will be sufficient to hold the antenna and not much in the way of a rotator will be needed. The InnovAntennas Moxon Directional Antennas require no balun and present a balanced 50-ohm load to the radio, connection of the coax to the antenna is carried out by way of screw terminals on the antenna. The Antenna is rated to survive in 99 Mph winds.
Not Yet Reviewed
$783.99
InnovAntennas OP-DES Opposing Phase Driven Element System HF Yagis
InnovAntennas OP-DES Opposing Phase Driven Element System HF Yagis are a relatively new development by InnovAntennas. The ends of the driven element of these antennas are angled backwards, parallel to the boom. The opposing phase relationships in them achieves a very clean directional pattern with few side lobes. The resulting performance includes very good gain over a wide frequency range, along with a very good front-to-back ratio. These monoband beams antennas are available in a variety of boom lengths and element counts, to fit in with each operator's needs and their budget. Feature and Benefits of the InnovAntennas Monoband OP-DES Yagis: • Have bent driven elements to dramatically reduce side lobes and to help provide with constant performance characteristics • Super Wide Bandwidth - the broadest SWR, gain and f/b bandwidth of all our antennas, the OP-DES is best suited to HF applications where performance and a wide frequency range of low-SWR are needed in a single package. • High F/B ratio as with the LFA and OWL, the OP-DES Yagi has an exceptional Front to Back ratio for a direct-feed, 50Ω Yagi, which suppresses unwanted signals from behind your antenna! • Constant Impedance & 'All-Weather' Stability – Similar to the LFA and OWL, the OP-DES Yagi is able to maintain impedance in wet weather and therefore will not de-tune like other antennas can • 50-ohm Direct Feed - No Matching Loss - The OP-DES Yagi has been computer optimized with the 'bent' driven element in place to ensure a 50 ohm feed-point with no matching loss and minimal resistive loss • Class-Leading Direct Feed Yagi Performance - For a given boom length, the OP-DES Yagi provides superior all-round performance as compared to any other HF direct feed Yagi • Simple SWR Fine-Tuning Feature - No two locations for an antenna are the same. With this in mind the requirements of the perfectionist as well as the everyday user in our sights, the driven element of the OP-DES has adjustable end sections to allow for very simple SWR fine-tuning The most important part of your receiver - the antenna - has to be the best part. The antenna is considered the most important part of your station. After spending thousands on radio equipment, don't short-change the station by choosing anything less than the InnovAntennas OP-DES HF Yagi.
Not Yet Reviewed
$825.99
—
$999.99
DX Engineering PRO-STACK Broadband Antenna Phasing Systems
DX Engineering PRO-STACK Broadband Antenna Phasing Systems are designed to combine two identical Yagi or log periodic beams, or three quarter-wave vertical antennas, into a phased array for enhanced directional pattern selections and dramatically improved HF operations. There is no need for special coaxial delay lines with the DX Engineering PRO-STACK systems. Just connect your antennas to the system relay unit with equal-length 50-ohm coaxial cable assemblies. The PRO-STACK switch relay units are available with high-quality PTFE-silver plated SO-239, UHF female connectors. The matching PRO-STACK Control Console operates the system with a 1-of-3 source voltage control format at 12-15V DC with a user supplied four conductor control cable to achieve four different antenna phasing selections. PRO-STACK Broadband Antenna Phasing Systems operate across the 160 to 10 meter range. They have two antenna ports that can be used for any application requiring the four basic selections: 1. BIP - Both antenna ports In-Phase 2. BOP - Both antenna ports Out-of-Phase 3. BOTTOM - Antenna port 1 only 4. TOP - Antenna port 2 only. The unpowered default is 1 - Both ports In-Phase. Impedance matching is automatic in the PRO-STACK even when any antenna port is disconnected. Generally, stacked Yagi antennas are separated vertically with greater than one half wavelength free space. Since the DX Engineering PRO-STACK Antenna Phasing Systems are broadband, they may be easily adapted to larger arrays. For example, four stacked Yagis may be combined by creating two sets of PRO-STACKS, with a third DX Engineering PRO-STACK to combine the first two. PRO-STACK systems may also be used to feed quarter-wave resonant vertical antennas for a high-gain, 4-pattern array. This arrangement requires three verticals, with the center #2 passive antenna element directly grounded to the system ground radial system at all times, while elements #1 and #3 are then fed in various phase relationships by the PRO-STACK. Details are in the complete PRO-STACK PS-2B Instruction Manual linked here in "Documentation" tab. The full- color printed manual is included with the system relay unit. PRO-STACK Broadband Antenna Phasing Systems are available as separate Relay Units for operators who have automated BCD switching devices, and as packaged systems with Relay Unit and matching manual Control Console. Features of the DX Engineering PRO-STACK Broadband Antenna Phasing Systems include: * Power handling up to 5 kW * Broadband coverage on 160-10 meters * High impact shielded weatherproof housing * High-RF tolerant, silver-PTFE SO-239 (UHF female) connectors * Proven DX Engineering RF relays for high performance * Safe 12V relay operation * DC-powered control console allows battery or solar emergency operation * MOV surge protection on control lines * External, removable control line connector * RoHS-compliant assembly Dominate the airwaves with DX Engineering PRO-STACK Broadband Antenna Phasing Systems. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$895.98
—
$935.99
Momobeam Duo4 12/17 Dual Band HF Yagi Antennas
Momobeam Duo4 12/17 Dual Band HF Yagi Antennas are designed for the 12-meter and 17-meter WARC bands. Despite its very compact dimensions, it features full-size elements for superior efficiency. A unique aspect of this antenna is its innovative "open sleeve" feed for the 24 MHz driver, which eliminates the need for a direct connection and greatly simplifies assembly. The Duo4 delivers low SWR on both operating bands, making it an ideal match for modern transceivers and linear amplifiers. Assembly is simple and intuitive thanks to its square boom design, clearly labeled aluminum tubes, and hardware supplied in separate, marked bags. The antenna requires only one coaxial cable and a rotor for a small load, ensuring easy installation and reliable performance. Perfect for operators seeking exceptional signal quality in a compact footprint, the Momobeam Duo4 combines convenience, durability, and outstanding results for serious HF enthusiasts.
Not Yet Reviewed
$952.99
InnovAntennas 1712DUO 4-Element Yagi
InnovAntenna 1712DUO 4-Element Yagi is one of the latest designs from G0KSC. This very compact directional antenna for the 17 and 12m WARC bands (18 and 24 MHz) has no reflectors. One director per band and an LFA/dipole hybrid driver lies flat on its short, 5.1 ft. (1.56m) boom. This dual-band version has a second active element intentionally positioned for open-sleeve coupling with the hybrid driver. Consequently, this antenna requires only one feedline, avoiding potential interference and tuning issues caused by multiple feedlines. This short boom directional antenna design is a smart choice for the WARC bands. Since SWR bandwidth is not a requirement, optimization for excellent gain and good F/B on a short boom length is reached. This dual-band Yagi for 17 and 12m was calculated using advanced software and perfected by hand. Designer Justin, G0KSC, has achieved particularly good electrical properties and robustness to provide reliable performance, even in adverse weather conditions.
Not Yet Reviewed
$829.99
Momobeam DIP30 HF Monoband Rotatable Rigid Dipole Antennas
Momobeam DIP30 HF Monoband Rotatable Rigid Dipole Antennas are high performing rotatable rigid dipole antennas designed for the 30-meter band (10.1MHz). They feature Momobeam's exclusive F.T.L (Folded Top Load) system, which reduces antenna size without compromising electrical performance or bandwidth. This innovative design delivers full-size performance with an SWR below 1.5:1 across the entire band, making it ideal for modern HF operators. A 3kW-rated RF choke is included for reliable operation.
Not Yet Reviewed
$965.99
Momobeam Mono4-10 Monoband Yagi Antennas
Momobeam Mono4 10 Monoband Yagi Antennas are full size, four element antennas engineered to deliver excellent SWR bandwidth, optimal forward gain, and strong front to back performance across the 10 meter band. Despite their robust construction, these antennas remain lightweight, making them easy to handle while still offering the durability needed for harsh weather conditions. Designed for high performance installations, the MONO4 10 excels in multi stacked array configurations. Stacks can be optimized for maximum forward gain or arranged to broaden directional coverage across multiple regions—making them an excellent choice for contest stations and serious DX operators. Built on a sturdy square boom, each antenna comes with an assembly tool, spare hardware (bolts and aluminum tubing), and fully labeled components. All hardware bags and aluminum tubes are clearly marked, ensuring quick, accurate, and hassle free assembly. A 3kW RF choke balun is included as standard equipment—an essential component that many manufacturers offer only as an optional upgrade. Momobeam RF Chokes are built using high quality, low loss, double shielded coaxial cable with a Teflon dielectric, combined with carefully selected ferrite material sleeved over the cable. Together, these elements create a high impedance path for RF, providing excellent isolation between the antenna and the coaxial feedline. The Mono4-10 requires a medium duty rotator for proper operation.
Not Yet Reviewed
$955.99