Availability
HF Beam Antennas
EAntenna HEX6B Six Band Hexbeam Antenna
EAntenna HEX6B Six Band Hexbeam is a directional HF antenna for the six Amateur bands 20, 17, 15, 12, 10 and 6 meters. This design follows the ideas of G3TXQ Steve Hunt, the originator of the Broadband version of the Hex Beam antenna. However, this mechanical construction is a version refined by EAntenna with their long-standing antenna engineering experience. The result is an efficient, lightweight portable antenna for the high HF DX bands, which is ideal for use for DXpeditions and vacations. An installation at 20 ft. above the ground can work quite well, but a tower-mounted Hexbeam at a height of 35 to 60 ft. is known to perform as intended and produce excellent DX results. The HEX6B works as two element beam on each band. Ready-to-use wires and ropes are attached to the fiberglass struts and due to the mechanical tension of the struts, the beam is stretched to its fixed size all the time, so there is no sag on the wires. The radiator dipoles are connected to the vertical center support, with each band wire element attaching with screw clamps. The center support is designed as a coaxial transformer and balun, providing a particularly good match on each band, with one feedline for all six bands. The HEX6B forward gain is approximately 3dBD or better, the front/back ratio is between 13 and 22dB. SWR is 1.5:1 or better on all bands except 10m, where SWR is 2:1 or better. Each band can be used in full bandwidth without a tuner. The maximum allowed power is 5 kW. The fiberglass tubes are double coated against UV radiation. The setup of the HEX6B six band beam is simple and can be done by one person in about 30 minutes. All ropes and wires are ready, cut to length, so no tuning is required. Due to the low weight of only 18.7 lbs. (8.2 kg) this hex beam can be installed on a light aluminum push-up mast. Rotation is either done with a small rotator or by hand. The HEX6B mast clamp accommodates poles with a Diameter from 1.10 -2.05 in. (28-52mm).
( 6 )
$851.99
DX Engineering XB-5 Hexx Beam HF Antenna
The DX Engineering XB-5 Hexx Beam is a lightweight directional five-band HF antenna for the 20, 17, 15, 12 and 10 Meter bands that is ideal for permanent or temporary installations. What are the benefits of this oddly shaped HF beam antenna? There are many, such as its small turning radius and full legal-limit power handling on all bands. But the most important are that the XB-5 Hexx Beam receives signals very well and transmits RF very efficiently. Its special configuration of full-size wire elements reject noise so more signals are heard. Months of development have culminated in this advanced antenna design for easier assembly, improved SWR and better bandwidth while maintaining excellent front-to-back performance. The DX Engineering XB-5 is our best Hexx Beam to date. DXE-XB-5 is the complete HF antenna package of specialized DX Engineering XB-5 Hexx Beam components; some are new and pre-assembled. These essential components include the patented* Hexx Hub and the Stainless Steel and PTFE Rigid Flat Feeder which is fully balanced with the Maxi-Core® 20 1:1 Current Balun and Mount. Also included are the all-new Heavy-Duty "Ice" Spreader Support Ropes with thimbles and stainless steel carabiners, better fiberglass Center Post and Spreaders, the Heavy-Duty Mast Mount, newly configured Element Wire Kits with the unique DX Engineering Wire Guides and innovative Element Spacer Insulators. The DX Engineering XB-5 Hexx Beam design has a number of important advantages over other Hex Beams or a mini-Yagi: - New, easy and faster assembly - fewer parts to speed completion of the antenna project - Pre-made 4.4 mm heavy duty "ice" support ropes with thimbles and stainless steel carabiners - High CMI Balun (1:1 5kW) and Mounting Bracket included - New Heavy-duty Mast Plate with DXE Saddle Clamps - Strong fiberglass without slits - Pre-sized and pre-drilled element spacer insulators designed for simple antenna assembly and tuning adjustment - Improved SWR band coverage - Small turning radius - the XB-5 Hexx Beam has a turning radius of 11' - Gain - 5 dBi (3 dBd), depending on band - similar to 2 element Yagi, far exceeding the performance of multi-band mini-beams - Front-to-Back – greater than 20 dB, depending on band - Wind balanced - Hexx symmetry reduces torque on the rotator - Light weight – about 25 lbs. fully assembled - Wind load – only 5 square feet wind surface - Can be turned with a light duty rotator - Performs well at low heights - good results at 25 to 35 feet above ground - Handles full legal limit power – no power restriction as on competing antennas - Low Noise results - approaches performance of closed loop antennas - Full length HF antenna elements - no lossy coils or traps - Five-Band Stainless Steel/PTFE Rigid Feeder System – balanced for best pattern - Requires no matching network - direct single 50 ohm coax feed The DX Engineering XB-5 Hexx Beam is one of the best performance values on the market for a directional HF antenna. *(US Patent No. 8,669,911, US Patent No. D 624,060, British Patent No. GB248003 B)
( 3 )
$1,247.92
EAntenna HF Rotatable Antennas
EAntenna HF Rotatable Antennas include a comprehensive range of mono-band and multi-band Yagi beams and rotatable Delta Loops and Dipoles. Find the band coverage and performance antenna of your dreams right here. For example, the exciting EAntenna 59+ provides great performance on 20, 17, 15, 12 and 10 meters! Check out the specs on this great line of HF directional antennas. DX Engineering offers EAntenna because their attention to manufacturing detail is excellent! Their Yagi, log periodic, and rotatable dipole antennas are built with high-quality stainless steel hardware and aircraft-grade aluminum. As you look through these selections, be aware that advanced, cutting-edge computer modeling and optimization techniques were used to produce every one of the EAntenna premier HF beam antennas and state-of-the-art VHF and UHF Yagi antennas. Their mechanical designs are very robust in every way, as most are rated for at least 100 mph wind survival. To see additional information about each antenna, click on the "More Details" link on the antenna of interest. Then click the Specifications tab to see all of the physical and electrical characteristics of that antenna. EAntenna products are offered exclusively in North America by DX Engineering. Plus, we can ship these great antennas internationally! When you're making plans for a new antenna at your station, look no further for the outstanding solutions by EAntenna, "The Best Choice for Your Antenna System!" NOTE: Manuals are normally supplied bilingual. If your manual lacks an English section, contact DX Engineering for an English version.
( 47 )
$355.99
—
$2,215.99
OptiBeam HF Directional Antennas
OptiBeam antenna technology has achieved directional antennas with extraordinary electrical properties, including the highest efficiency, optimum band coverage, nearly constant gain and unchanging radiation pattern across the band, and low SWR. These antennas maintain consistent electrical characteristics under all weather-conditions and include a high power balun with UHF female connector for your 50 Ohm coaxial cable. OptiBeam Antennas are distinguished by their advanced mechanical qualities. Specially configured, stable and properly shaped element holders, robust square and round booms with effective and very solidly-built element transitions are OptiBeam exclusives. They provide advanced physical properties, including proper balance and the highest stability of the entire system. Elements are perfectly aligned and secured against torsion with minimal sag for a visually pleasing appearance. OptiBeam antennas are made for those who understand the true value of investing in proven electrical performance and unequalled mechanical quality for the ultimate in reliability. They are built to withstand the harshest conditions using the very best materials, including high quality aluminum alloys, UV stable synthetic parts and stainless steel hardware. OptiBeam antennas are designed to be easier to build than others, arriving in subassemblies with every part carefully sorted, clearly labeled, and extremely well packed for worry-free shipment and straightforward installation. In 2025, the OptiBeam brand of products was exclusively acquired by WiMo Antennen und Elektronik GmbH. The OptiBeam portfolio is now produced by WiMo and integrated into its product offering. With this acquisition, WiMo will integrate the technical expertise and know-how gained from OptiBeam's many years of experience in antenna technology and will provide new impetus with its extensive service and sales network. The primary goal is to successfully continue OptiBeam's antennas, ensure long-term customer service and spare parts availability, and leverage development potential. For enthusiastic operators of all pursuits, OptiBeam provides the advantage of pure performance. Proven in the field and confirmed by the most demanding hams around the world – choose OptiBeam for your station.
( 5 )
$1,338.99
—
$6,172.00
DX Engineering XB-5 Hexx Beam 5-Band Wire Element Kit
DX Engineering XB-5 Hexx Beam 5-Band Wire Element Kit is a component of parts and assemblies that are used to construct the directional XB-5 HF Antenna. It features innovation and convenience for the assembler of this high performance antenna. Here are the items included in this kit: - Wire Elements made from high quality AWG 14 stranded copper with a relaxed black PVC insulation for longevity - Band specific Driven Elements and Reflectors are pre-cut and pre-assembled with color coded and printed shrink tubing near one end for easy identification - Floating Element Wire Guides – studded element and P-clamps with nylon guide tubes that secure the elements to the Hexx Beam fiberglass spreaders while allowing independent movement to reduce strain - Innovative Element Spacers, five pairs of band specific lengths made of Acetal rods that are cut and drilled for specific band spacing. Closely spaced holes secure driven and reflector wire element ends with a simple serpentine routing. This allows easy adjustments of element lengths if tuning is necessary. Refer to the DX Engineering XB-5 Hexx Beam HF Antenna manual for more information.
( 1 )
$375.99
Chelegance JHEX-6 HF 6-Band Hex Beam Antennas
Chelegance JHEX-6 HF 6-Band Hex Beam Antennas are powerful, full-size 6-band Hex Beam antennas built for hams who want serious performance—whether you're into contesting, chasing DX, or talking with fellow hams around the globe. Covering the 20, 17, 15, 12, 10, and 6-meter bands, and rated for 2000 watts PEP, the JHEX-6 is ideal for DXing and high-duty-cycle operation. The JHEX-6 is engineered for rapid deployment, featuring a modular, tool-free design that allows for quick assembly and effortless installation by a single operator—ideal for stationary installations, field operations, and solo deployments. With full-size elements on each band, it delivers exceptional gain and directivity, making it a top-tier choice for demanding operators. A 1:1 balun ensures optimal feedline performance, while its lightweight construction—weighing just 26.5 pounds—enhances portability and ease of setup. Built for long-term reliability, the JHEX-6 incorporates precision-molded cable lugs, a robust beam structure, and aluminum-reinforced plug-in joints with butterfly screw connections for fast, secure assembly. Its rugged 1.40-inch (35mm) 304 stainless steel base tube provides a dependable mast mounting solution, even in harsh environmental conditions.
Not Yet Reviewed
$1,199.98
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles offer high performance multi-band HF operations, and they are an excellent choice where there's not enough space for a full-size dipole or Yagi. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these unique multi-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. DIEX Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles power handling is 1500W PEP SSB, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that a directional HF antenna should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 2 )
$409.99
—
$765.99
DX Engineering XB-5 Hexx Beam Spreader and Center Post Kit
The DX Engineering XB-5 Hexx Beam Spreader and Center Post Kit is a component of the XB-5 Hexx Beam that contains parts for the antenna assembly. The Spreaders and Center Post are manufactured from high quality fiberglass material and all the parts are used as-is and no cutting or drilling is required. This helps to reduce the risk of stray fibers becoming a problem during assembly. This DXE-XB-5-SCP kit includes: - Pre-assembled Spreader Support "Ice" Ropes terminated with thimbles - Stainless Steel Carabiners for easy assembly - Pre-cut Fiberglass Spreader Sections of the appropriate lengths and diameters - Pre-cut Fiberglass Center Post - Element Clamps to serve as stops for the spreader sections and Guy Ring - Vinyl Cap - Guy Rings - only the 1-1/4 in. ID is used on the Hexx Beam Center Post (four other sizes may be retained for use as desired) - Spreader End Padded P-clamps Refer to the DX Engineering XB-5 Hexx Beam HF Antenna manual for more information.
Not Yet Reviewed
$209.99
Diex 3 Element Monoband Full Size Yagi Antennas
Diex 3 Element Monoband Full Size Dipole Antennas are full sized directional antennas covering the 20 through 6-meter amateur bands. Expertly engineered and crafted in Brazil from quality aluminum tubing and durable materials, these antennas are built to endure harsh environments while providing long-lasting, high-performance operation. With a power rating of up to 2000 Watts PEP, these antennas are ready for demanding applications. Offering at least 8 dBi of gain and greater than 500 kHz of bandwidth at less than 2:1 SWR, these monoband antennas will help your signal reach further – whether across the country or around the globe. Designed for efficiency, these 3 Element Monoband will get your signal further and let you chase far away DX.
( 3 )
$379.99
—
$995.99
Diex Antennas Single-Band Full Size Rigid Rotatable Dipoles
Diex Antennas Single-Band Full Size Rigid Rotatable Dipoles provide coverage of one specific HF band. Built as a full-size resonant dipole, Diex aluminum tubing antennas provide excellent performance and are handled with a lighter tower and smaller rotator, offering a very economical alternative to the expense of a Yagi. Crafted with precision in Brazil using quality materials, they are designed to withstand tough environments assuring long-lasting service. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these single-band HF antennas provide very good directionality depending upon installed height above ground. They feature the flexibility of physical adjustments to set the lowest SWR to a specific frequency. Diex Antennas Single-Band Full Size Rigid Rotatable Dipoles power handling is 1,500W+ PEP, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 6 )
$115.99
—
$209.99
DX Engineering XB-5 Hexx Beam Hexx Hub
The patented* DX Engineering XB-5 Hexx Beam Hexx Hub provides a strong, solid base for the entire XB-5 Hexx Beam antenna. Made from cast aluminum and machined to perfection, the Hexx Hub is far superior to available base plate designs. The Hexx Hub has integral V-Saddles and with the included Stainless Steel V-Bolt hardware firmly attaches Hexx Beam fiberglass spreaders in proper alignment without drilling or crushing. The upper and lower mast mounts are integrally cast into the hub, eliminating the need to find separate mounting flanges, reducing assembly time, improving mast alignment and providing a far stronger heavy duty attachment for the mast. Kits include: * Cast aluminum Hexx Hub * Twelve 1 1/2 in. short stainless steel V-bolts * Twelve 1/4-20 in. stainless steel hardware kit for V-bolts * Six 1/4-20 in. stainless steel hex head bolts * Six 1/4-20 in. stainless steel hex nuts * Six 1/4-20 in. stainless steel flat washers * Six 1/4-20 in. stainless steel split washers Use DX Engineering XB-5 Hexx Beam Hexx Hubs as replacement parts, for upgrading other kits or for home brew projects. *US Patent # D 605,184
( 1 )
$102.99
DX Engineering XB-5 Hexx Beam 5-Band Rigid Feeder System
The patented* DX Engineering XB-5 Hexx Beam 5-Band Rigid Feeder System, DXE-XB-5-FF, is specifically designed for the DX Engineering XB-5 Hexx Beam. A professionally engineered Stainless Steel and PTFE flat balanced feedline system, the Rigid Feeder eliminates vulnerable coaxial cable sections - providing a weatherproof, low-loss, high power balanced connection to all five bands - 20, 17, 15 12 and 10 meters. Used with the DX Engineering Maxi-Core 1:1 Balun, this balanced feeder solves the pattern-skewing problems created by the unbalanced coaxial post feeders used by others, for the optimal antenna pattern and maximum XB-5 Hexx Beam performance. This revolutionary Rigid Feeder attaches directly to the outside of the full-size 1-1/4" fiberglass Center Post of the DX Engineering XB-5 Hexx Beam. There is no drilling for attachments that would weaken the Center Post. The integral wire element center insulators with the unique serpentine wire grip and strain relief assure long, reliable performance. Rated to handle more power than the legal limit, the DXE-XB-5-FF Rigid Feeder is pre-assembled and tested and is also ideal for retrofitting to other hex beams. Intended for use the DX Engineering XB-5 Hexx Beam Wire Element Kit, DXE-XB-5-EK. *US Patent No. 8, 669,911, US Patent No. D 624,060; British Patent Number GB248003B
Not Yet Reviewed
$192.99
InnovAntennas DXC-140 40 Meter Rotatable Dipole
InnovAntennas DXC-140 40 Meter Rotatable Dipole covers the entire 40-meter band with particularly good efficiency, impressive SWR bandwidth and a very reasonable wingspan, just over 39 ft. (12m). There are several methods to shorten a mast-mounted rotatable dipole, including loading coils and capacity hats. The position of the coils is critical to efficiency--closer to center is mechanically easier, further out is electrically better. The designer has used both methods to build the Delta C-140 antenna robustly and efficiently, limiting the size to a turning radius under 20 ft. (6 m) that many radio amateurs can easily mount on their tower mast and rotate within their property limits. The advantage of this design is a very large usable bandwidth of the antenna--the DXC-140 can be used over the entire internationally approved range from 7.0 to 7.3 MHz without having to use a tuner (SWR 2:1 or better). In the DXing range from 7.0 to 7.2 MHz, the SWR is usually equal to or better than 1.6:1, making the efficiency of the antenna 89 percent! Due to the robust construction of the DXC-140, no guy wires are necessary. Some of the images of this model installed show examples with guy wires, as chosen by individual user dependent upon the location, due to the expectation of snow and ice, for example. However, the mechanical design and construction will handle heavy loads, with the element diameter of 2.17 in. (55mm) in the center with a wall thickness of 0.078 in. (2mm). The element diameter decreases towards the end of the element save weight, but the ends still have a diameter of 0.98 in. (25mm) to easily support the capacity hats. All in all, the DXC-140 antenna combines a carefully calculated design with a very robust construction from an experienced antenna designer. This is also supported by the materials used: UV-resistant insulators, seawater-proof stainless steel hardware, and aircraft-grade aluminum elements. The result is a rotatable dipole with high efficiency, with an overall length of only 39.4 ft. (12 m) and a weight of only 18.7 lbs. (8.5 kg). The InnovAntennas DXC-140 40 Meter Rotatable Dipole is creating enthusiasm for many radio amateurs around the world. Order the DXC-140 for your station from DX Engineering.
( 1 )
$1,128.99
DX Engineering PRO-STACK 2 Control Consoles
DX Engineering PRO-STACK 2 Control Consoles are designed for use with DX Engineering PS-2 and PS-2B switches. They require 12 Vdc well-filtered at 2 amps (fused) minimum.
( 1 )
$195.99
QRO.cz Stack Match High Power Broadband Antenna Phasing Switches
QRO.cz Stack Match High Power Broadband Antenna Phasing Switches are high-performance broadband antenna combiner designed to impedance match two Yagi antennas to a single transceiver (TRX). Ideal for mono-band, tri-band, or multi-band antenna systems, they support both in-phase (BiP) and out-of-phase (BoP) configurations, enabling advanced stacking and phasing configurations. Whether you're optimizing a contest station or enhancing DX performance, these Stack Match 1-2 switches allow seamless switching between upper, lower, BiP, and BoP modes. Built with high-quality components and housed in a rugged aluminum enclosure makes them a reliable choice for demanding HF operations.
Not Yet Reviewed
$559.99
DX Engineering XB-5 Hexx Beam Mast Mount Kit
The all-new DX Engineering XB-5 Hexx Beam Mast Mount Kit, DXE-XB-5-MMK, is a component of the DXE-XB-5 Hexx Beam, used in the initial assembly and final mounting of the antenna onto a user supplied mast of 1.25 to 2.00 in. OD. The DXE-XB-5-MMK Mast Mount includes: - One Center Post Aluminum Mounting Tube, 1.50 in. OD for the XB-5 Hexx Beam - One Element Clamp for use on the Center Post during assembly. - One Mast Mount Plate, Heavy-Duty, 1/4 inch formed aluminum 16 x 5.125 in. with inline clamp holes - Two DXE-SAD-150A U-Bolt Saddle Clamps for the Hexx Beam Mounting Tube - Two DXE-CAVS-2P V-Bolt Saddle Clamps for the user supplied 1.25 to 2.00 in. OD mast. Additional lower holes accommodate two optional DXE-SAD-300B U-Bolt Saddle Clamps for only a 3.00 in. OD mast, or two DXE-CAVS-3P for a 2.00 to 3.00 in. OD mast, or two DXE-SSVC-3P Clamps for a 2.375 to 3.000 in OD steel mast ++++++++++++++++++++++++++++++++++++++++++++++++++++++ This DXE-XB-5-MMK Mast Mount Kit may also be used with the supplied Saddle Clamps to create a short extension at the top of a 1.25 to 2 in. OD mast with an optional 1.50 in. OD only tubing to mount a small VHF or UHF beam or vertical. This kit cannot be added to the top of any Hexx Beam. +++++++++++++++++++++++++++++++++++++++++++++++++++++ This aluminum plate is available separately as DXE-MTMP, to mount a 1.25 in. OD short upper mast. The two upper holes on this plate accommodate Stainless Steel V-Bolt Saddle Clamps model DXE-SSVC-150P for an upper mast mounting a range of 1.00 to 1.50 in. OD steel. The lower inner holes will accommodate two DXE-SSVC-2P Stainless Steel V-Bolt Saddle Clamps for a 1.00 to 2.00 in. OD steel mast, or the lower outer holes accept two DXE-SSVC-3P Stainless Steel V-Bolt Saddle Clamps for a 2.375 to 3.000 in OD steel mast. All applicable Saddle Clamps are sold individually, only at DX Engineering. Off-brand clamps will not fit this plate.
Not Yet Reviewed
$119.99
Diex Antennas Two-Band Shortened Rigid Rotatable Dipoles
Diex Antennas Two-Band Shortened Rigid Rotatable Dipoles provide coil-shortened specialized coverage of two non-adjacent HF bands that can complement band coverage of existing antennas. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotatable mast, these unique two-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of coil-shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. Diex Two-Band Shortened Rigid Rotatable Dipoles power handling is 300W PEP SSB and 100W maximum for digital modes, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 7 )
$215.99
—
$309.99
DX Engineering W1ZR 6 Meter Add-On Kits
DX Engineering W1ZR 6 Meter Add-On Kits are 3-element hardware kits designed for an existing triband or monoband HF beam. Unlike other add-on kits that use clear polycarbonate, these kits include black polymer plastic for the construction of the plates. These kits include: * Six 6 ft. x 0.375 in. x 0.058 in. aluminum tubes, 6063-T832 drawn, no slits * Three 3 ft. x 0.500 in. x 0.058 in. aluminum tubes, 6063-T832 drawn, one end slit * Six V-saddle clamps, 1-2 in. outside diameter applications * Six element clamps for 0.500 in. and smaller tubes * Two 0.250 in. x 7.50 in. x 11.50 in. plate, polymer plastic, blank (sufficient to make four insulator plates) * Six 1/2 in. stainless steel saddle clamps, 1/4 in. U-bolt thread size Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Want to add 6 meters to that old HF Yagi? Try one of these DX Engineering W1ZR 6 Meter Add-On Kits!
Not Yet Reviewed
$315.26
WiMo - EAntennas 2850MOX Dual Band Moxon Antenna for 10 and 6 Meters
WiMo - EAntennas 2850MOX Dual Band Moxon Antenna for 10 and 6 Meters is perfect for Sporadic-E QSOs on these bands, as well as for local and regional weak-signal operations on SSB, CW, and Digital Modes. The 2850MOX is a horizontally polarized directional antenna that offers high gain for its very compact dimensions. This antenna features an additional third element for especially good gain on the 6 meter band. The 2850MOX Dual Band Moxon advantages: - Radiator configuration offers high gain: 8.3 dBi - 6m, 10.5 dBi - 10m - Relatively compact dimensions - Front-to-back ratio is very good; 12dB on 6m, 21dB on 10m - Flat SWR curve over a wide bandwidth The 2850MOX Dual Band Antenna covers 28-29.7 and 50-52 MHz, requires only one coax feed line, and the included 3kW balun has an SO-239 connector. It has a short boom of 180cm (5.9 ft.) and a low weight of only 6.2kg (13.67 lbs.). Ideal for the restricted property and for temporary or portable operations, this antenna can fit well on an existing mast where space is limited. Join the fun of weak-signal operations, locally, regionally or long range via Sporadic-E for DXing or contesting on the 10 and 6 meter bands. The 2850MOX offers high performance with very reasonable dimensions at a low cost.
( 8 )
$469.99
Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles
Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles provide coil-shortened specialized coverage of a single HF band that can complement band coverage of existing antennas. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotatable mast, these unique single-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of coil-shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles power handling is 300W PEP SSB and 100W maximum for digital modes for the 20, 30 and 60M models, 1000W PEP for 80M and 1500W PEP for 40M, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 7 )
$215.99
—
$679.99
InnovAntennas DXR Series Multi-Band HF Beams
InnovAntennas DXR Series Multi-Band HF Beams have short booms with full-size elements or capacity-loaded shortened elements, all with excellent performance, making them very popular internationally. The DXR Series interlaced-element antennas, optimized by G0KSC over a long period of time, achieve the best possible balance between compact size and performance. For the DXR Series Multi-band Yagis, equal attention was paid to a very solid construction and sufficiently small component and packaging size, to keep shipping costs within reasonable limits. Click on any model listed for specific details and specifications. InnovAntennas DXR Series Multi-Band HF Beams are available exclusively from DX Engineering in North America. Important features of InnovAntennas DXR Series Multi-Band HF Beams: * No traps, matching links, or hairpins * Only one feed line for all bands * Careful selection of materials without regard to cost * Very robust construction with still manageable package size The DXR Series beams use a 1.97 x 1.97 in. (50 x 50 mm) square boom with 0.078 in. (2 mm) wall thickness. A square boom has the advantage that the elements cannot twist in the plane. On the other hand, it is slightly heavier than a round boom of the same stiffness. The DXR Yagis do not require any bracing of the boom. The longest elements are 1.378 in. (35 mm) diameter in the middle and taper relatively quickly to achieve a good compromise between weight and strength. This construction also helps to avoid constant vibration even in light winds. With these multi-band Yagis, care has been taken to ensure that there are never more than the elements of three bands nested within each other. This is because each additional element for one band can cause interference on another band. This negative effect was avoided by careful manual optimization. The result is the best possible matching over a wider band range than other antenna designs. In most cases, no tuner is necessary; the SWR minimum can be precisely set by adjusting the element lengths. Due to the robust construction and the absence of moving or electrically active components such as coils, traps, hairpins, etc., an InnovAntennas DXR beam is maintenance-free for many years. The insulators are UV-resistant and designed for a wide temperature range. The mounting hardware uses sea-water resistant stainless steel and the aluminum is type T6 6066/6082, which is also used in aviation. It is nice not to have to climb the mast every year to maintain the antenna. The DXR Series Multiband beams are designed to require only one feed line. This makes installation on a mast with a rotor very easy. And the use of modern SDR transceivers, which allow the observation of several bands at the same time, becomes really useful. The one feed line is connected directly to the solid distribution rails of the fed elements. By avoiding baluns, matching elements, traps, or hairpins for tuning, transmit power is only limited by the coaxial cable and connectors. Note: Front-to-back ratio (F/B) and SWR bandwidth data for the DXR Series will be added as it becomes available. Many models of the DXR Series are available as a "super-compact" version, on which the longest elements have been shortened with capacity hats, thus reducing their turning radius considerably. The installation of these impressive antennas is possible even where space is limited.
( 4 )
$1,439.99
—
$2,097.99
Diex Antennas DXM Series 2 Element 40 meter Directional Antennas
Diex Antennas DXM Series Single-Band Shortened 2 Element Directional Antennas provide coil-shortened specialized coverage of a single HF band that can complement band coverage of existing antennas. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotatable mast, these unique single-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of coil-shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles power handling is 300W PEP SSB and 100W maximum for digital modes for the 20, 30 and 60M models, 1000W PEP for 80M and 1500W PEP for 40M, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
Not Yet Reviewed
$1,129.99
Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles
Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles are compact all aluminum self-supported dipole antennas specifically designed for "Limited-Small space" applications. Designed for use with an antenna tuner, each element is fitted with an M5 stud and wing nut to enable easy feed wire connection. The central bracket has two U bolts to allow attachment to a 50mm (1-7/8 in.) OD mast. Radiating elements are manufactured from telescoping 25mm and 22mm diameter "drawn," not extruded, aluminum tubing. This makes them flexible and extremely resilient to high winds and bird landings. The width of the assembled antenna is only 6.8 meters (22.31 ft.). They are configured to operate in a frequency range of 3-54 MHz with the aid of a manual/auto tuner. Ultimate band coverage is subject to the functional range of your antenna tuner. If not using a remote mast-mounted tuner, then an RF choke or balun should be used at the antenna to limit RFI. Dipole elements are two-piece to reduce the shipping length to 202 centimeters (79.53 in.). These antennas are very easy to assemble and with a weight of only 3 kg (6.6 lbs.) they are extremely easy to erect. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. These antennas are ideal for pairing with an LDG-RT-RC-100 remote autotuner and a Channel Master CNM-9521A light Duty Rotator System. Order Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles and accessories from DX Engineering!
( 5 )
$429.99
Diex Antennas DXS Series Multiband Directional Antennas
Diex Antennas DXS Series Multi-band 3 Element Yagi Antennas delivers high-performance, Multi-band operation for the 40, 20, 15, 10 and 6-meter amateur bands. The DXS antenna series features three tunable aluminum elements, engineered for optimal directionality and gain. With a power handling capacity of up to 1,500 watts, these antennas are built to perform under demanding conditions. Crafted in Brazil using quality materials, the DXS Series is designed for long-lasting, trouble-free service. Easy to assemble and require only a modest mast or tower, these antennas offer an economical and effective solution for getting on the air.
( 1 )
$1,279.99
—
$1,745.99