Availability
11 Results Found For "in-line"
Chelegance Guy Line Anchors
Chelegance Guy Line Anchor Rods are made from steel with a shaft diameter of 9mm, just under 3/8in. and they are 7.9 inches in length, with a built-in hook that makes tying off your guy ropes a breeze. Sold in packs of 4.
Not Yet Reviewed
$20.99
Chelegance Guy Line Rope
Chelegance Guy Line Rope provides the support necessary to keep your antenna standing tall! These guy line ropes are sold in 328ft. (100m) lengths and they are approximately 1/4 in. (6mm) in diameter. They are made from a polyester material with a breaking strength of 500lbs. (227kg).
Not Yet Reviewed
$39.99
DX Engineering Radial Wire Metal Anchor Pins
DX Engineering radial wire metal anchor pins are perfect for fastening radials below the grass line to eliminate the risk of damaging your radials during lawn maintenance. They are manufactured from 11-gauge steel and are 6 in. long to help keep the cables buried properly.
( 39 )
$22.99
—
$59.99
Mastrant MA1 Universal Heavy Duty Mast Guying Clamps
Mastrant MA1 Universal Heavy-Duty Mast Guying Clamps accommodate a wide range of mast diameters and support both 3 and 4-directional guying configurations. A 4-direction kit can also be used for 3-direction configuration, providing maximum flexibility for installation. MA1 brackets are made from 5/32-inch thick 304 stainless steel and feature a drilled hole to insert a screw for securing the guying clamp to the mast. Another option is to utilize a rubber pad between the clamp and the mast made from weather and UV stabilized EPDM. It spreads the pressure on the larger surface of the mast, reducing slippage and moreover isolating the clamp from the mast. The guy line holes measure 5/8-inch (16mm) diameter and are compatible with shackles, chain couplers, and carabiners sized from 5/32-inch (4mm). They also accommodate thimbles from 1/8-inch (3mm) up to 3/8-inch (10mm).
( 1 )
$23.00
—
$33.00
Mastrant MA2 Universal Mast Guying Clamps
Mastrant MA2 Universal Mast Guying Clamps accommodate a wide range of mast diameters and support both 3 and 4-directional guying configurations. A 4-direction kit can also be used for 3-direction configuration, providing maximum flexibility for installation. MA2 brackets are made from 3/32-inch thick 304 stainless steel and feature a drilled hole to insert a screw for securing the guying clamp to the mast. Another option is to utilize a rubber pad between the clamp and the mast made from weather and UV stabilized EPDM. It spreads the pressure on the larger surface of the mast, reducing slippage and moreover isolating the clamp from the mast. The guy line holes measure 1/8-inch diameter and are compatible with shackles, chain couplers, and carabiners sized from 5/32-inch (4mm). They also accommodate thimbles from 1/16-inch (2mm) up to 5/16-inch (8mm).
Not Yet Reviewed
$18.00
—
$24.00
DX Engineering Direct Coax Feed Add-On Kits
DX Engineering Direct Coax Feed Add-On Kits are designed for the Hustler BTV Series of antennas. They allow for a direct connection with a coaxial cable PL-259 (UHF male) connector. Manufactured from heavy-duty stainless steel, these add-on kits allow for a convenient connection from your coaxial cable feed line directly to the base of the Hustler BTV series vertical antennas by adding a mounted SO-239 (UHF female). They may be positioned in any one of three different directions to accommodate a straight-in or sideways connection from your feed line. If you are looking for a professional and reliable installation, then order a low power or high power (low loss) coaxial jumper cable for connecting your radial plate with a bulkhead connector. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Direct Coax Feed Add-On Kits include a laser-cut stainless steel bracket, high quality SO-239 with PTFE insulation, and stainless steel hardware. Order one for your BTV vertical!
( 79 )
$42.99
WiMo 23050 Metal Guy Ring Kits
WiMo 23050 Metal Guy Ring Kits are perfect for stabilizing WiMo metric telescoping aluminum masts. This strong, metal guy ring features a game-changing design with a cable management slot that allows for the rotation of the mast—while preventing the tangling of cables with the guys. The handy 25mm slot for cables (0.984 in.) will accommodate most rotator and RF connectors. Four plastic bushings are included: 50mm (1.969 in.), 40mm (1.575 in.), 30mm (1.181 in.), 20mm (.0787 in.). These bushings provide the flexibility to choose the correct height to guy your mast. Use more than one kit for a tall mast. Properly spaced holes provide attachment for guy ropes or lines for a three-way guying system. Note: If used to guy radiating vertical antenna tubing, non-metallic guy lines must be used.
( 2 )
$89.99
DX Commander Venture HF Multi-Band Vertical Antennas
DX Commander Venture HF Multi-Band Vertical Antennas are designed for portable operation. The design is built on the proven success of other DX Commander antennas but optimized for portable operation. Efficiently resonant on 40, 20 and 15 meters, the DX Commander Venture is designed for some of the most popular bands for portable operation. Using the same principals as a fan dipole, with several vertical wire elements of various resonant lengths attached to a common feedpoint. The Wire elements and any supporting ropes are arranged on spacer plates with "speed slots" around the non-conductive fiberglass mast. When a proper radial system is attached to the radial plate, the Venture will achieve quarter-wave vertical performance with natural resonance and low SWR on the bands it's configured for with no antenna tuner required. Band hopping DXing and simultaneous multi-band multiplex operations are supported. The Venture is rated at 1500W SSB/CW, 400W FT8 and other digital modes. The Venture antenna is only 23 feet (7 m) so setup is a cinch in the field. SWR bandwidth is typically 300 kHz on the bands the antenna is cut for. The Venture, while being designed for 40, 20 and 15 meters, can be used on 10 and 6 meters with an antenna tuner. DX Commander Venture Features and Specifications: Ground Post: Supplied with a Fiberglass Ground post. Alloy Plates: Aircraft quality 5251 alloy, laser cut in England before deburring to give that "hammered" look, which eliminates sharp edges and provides a nice finish. Spreader Plates: Marine-grade high-density polyethylene sheet material from USA, charcoal-gray, UV and environmentally stabilized to withstand the harshest of marine and high RF conditions. Spreader Plates are machine cut in England to DX Commander specifications. Shock Cord: Marine Grade shock-cord, with a UV and RF stable Dyneema woven exterior. Hardware: Kit includes Stainless Steel bolts, wing nuts, and spade connectors. Coaxial Connector: UHF Female SO-239 coaxial connector, nickel plated brass with PTFE dielectric. Fiberglass Poles: Made to DX Commander specifications in a spiral wound fiber, high-quality epoxy and paint finish. DX10 Wire: Made in England for DX Commander, DX10 wire has an outstanding reputation for both strength and in particular, extreme flexibility. The insulation is "arctic grade" and still flexible down to -40° F. Originally designed for military use, this insulation is particularly strong but highly flexible and the stranded annealed copper wire is approximately 19 AWG and is made from 24 strands of 0.008 in. (0.2mm) wire. All DX Commander Venture Antenna Kits come with everything you need (except the patio): • Rapide2 Mast – 23 ft. (7m) Extended Height • Supplied with a 1.50 in. (38mm) Fiberglass Ground Post • The DX Commander Ground Plate – 0.128 in. (3mm) thick laser cut 5251 alloy, with the hole for the included SO-239 assembly and 6 pre-drilled holes for the ground radials. Use up to 4 wires per connector and you can double up on connectors to achieve 48 radials total. • The Driven Plate – 0.128 in. (3mm) thick with pre-drilled holes for the three bands that the antenna is cut for. • The Venture kit comes with 3 spreader plates with speed slots to help facilitate setup in the field. One of the spreader plates has three holes to attach guy ropes to. • 328 ft. (100m) of DX10 Antenna Wire – cut all the elements first, then cut radials with the remaining wire. • SO-239 Coaxial Connector Assembly • Selection of Spade Connectors • Marine Dyneema Shock-Cord • Glue Lined Shrink-Wrap • Stainless Steel Hardware.
( 1 )
$354.97
DX Engineering 80 Meter Full Size Quarter Wave Vertical Antennas
DX Engineering 80 Meter Full Size Quarter Wave Vertical Antennas, model DXE-7580FS-VA-1, are high performance 68 ft. antennas that are tunable to operate over segments of the entire 75/80 meter band with an SWR of 1.5:1 or less! These antennas are a breakthrough in full size, quarter wave verticals that offer full performance, but don't cost an arm and a leg. Plus, if your neighbors are the slightest bit touchy, these are the antennas for you. Their slim lines can hide in even a small stand of tall trees. Some have even painted these antennas the color that matches the bark of their surrounding trees! Designed with 6063 corrosion-resistant aluminum tubing and stainless steel hardware, these 80 meter vertical antennas are very durable and attractive. Because of their full size height and tubing size, rope guying is required on these antennas, typically at two levels. They include the DX Engineering standard stainless steel Tilt Base to allow you to walk the antenna up or down with only a few helpers on the rope guys. These inexpensive 80 meter verticals are ideal for phased arrays! DX Engineering 80 Meter Full Size Quarter Wave Vertical Antennas have a bandwidth that is outstanding—up to 528 kHz under 2:1, depending on your radial field. Your internal tuner can get the SWR down to 1:1 on any DX frequency for maximum power transfer and full performance! Of course, another key to performance is a good ground radial system; we recommend 32 radials, 65 ft. long. Fewer radials will work, but with diminished results. DX Engineering 80 Meter Full Size Quarter Wave Vertical Antennas feature: -- 5 kW SSB and CW rating—unparalleled reliability -- High power handling capacity--high strength, UV-protected EXTREN® insulators -- Ultra-wide SWR bandwidth and unbeaten gain -- Highest wind ratings—Up to 100 mph with proper rope guying --High strength 6063/6061 tubing manufactured to DX Engineering specifications -- Easy tilt up and down— exclusive antenna mount features DX Engineering's patented Tilt Base, *U.S. Patent Number 7,432,875 -- No rust --100 percent stainless steel tubing clamps and hardware -- Reliability second to none--specially manufactured stainless and aluminum saddle clamps, stainless bolts, and precision machining on each antenna Note: For additional information, please look at the files under the "Documentation" tab. Make plans to install your DX Engineering 80 Meter Full Size Quarter Wave Vertical Antennas and join in the fun of having the best possible signal on the 75 and 80 meter bands with a great antenna!
( 1 )
$899.98
DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas
DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas are high-performance antennas specifically designed for use on Top Band. You will achieve the strongest possible presence at your power level and be competitive with a 160 meter vertical monoband antenna that is only 55 feet tall! A custom-designed capacity hat system allows you to get on 160 meters with unparalleled performance. Wires and ropes have been accentuated in our product image for your viewing clarity. They are much less visible in an actual installation with minimal visual impact for such a large antenna. DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas are tunable with an impressive 40 kHz bandwidth. This means that operation on the CW DX frequencies and DX Phone frequencies are within the range of most internal tuners - no physical changes to the antenna are necessary. DX Engineering DXE-160VA-1, made with sectional aluminum tubing, is a 55-foot high Monoband Vertical Antenna system with a massive 3-inch OD base section. Included with this antenna system is a rugged, patented* stainless steel pivot fixture for ease of raising, lowering and tuning adjustments. Engineered with 6061-T8 and 6063-T832 corrosion-resistant aluminum tubing, stainless steel mounting brackets and stainless steel hardware, this antenna is very durable and attractive. Why Does This Antenna Perform So Well for Its Height? The top capacity hat is large enough that the current along the radiator is almost constant. Typical shortened verticals for this band, with smaller top-hats, have currents that vary along the length and end up producing much less signal strength. This also works in the receive mode to let you hear weaker signals, although at this frequency range dedicated receiving antennas are almost a must. See DX Engineering's full line of Receive Antennas and Array Systems. DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas feature: * High Efficiency Design * 5 kW SSB and CW rated * Unparalleled reliability * Custom designed capacity hat engineered for top performance * DX Engineering Adjustable Matching Network configures the lowest SWR * Broad 2:1 SWR bandwidth - 40 kHz - CW + DX Phone * Lowest possible take-off angle reduces domestic QRM signals * Easy tilt up and down-- Unique fold-over antenna mount features DX Engineering's patented pivoting fixture, *U.S. Patent Number 8,130,168 * High power handling and high strength, UV protected EXTREN® insulators * Ultra-rugged construction starts with 3 inch OD Aircraft Grade heavy wall tubing * Withstands steady-state winds in excess of 50 mph The optional DXE-VRW-1 Manual Winch for easy one-person raising and lowering of the antenna is available from DX Engineering. You can move the DXE-VRW-1 winch between similar antennas in a multi-antenna installation. This antenna system requires the installation of a heavy duty mounting pipe set in concrete. Specifically, 3 in. OD high strength galvanized steel tubing with 0.250 in. minimum wall thickness and 7 ft. (84 in.) minimum length, which is available from DX Engineering; part number DXE-VGMT-3CG. A customer supplied 2-1/2 in. Schedule 80 pipe that has an outside diameter of 2.875 in. is also suitable. About 36 in. of the mounting pipe should extend above the concrete. Depth of the mounting hole and amount of concrete is dependent on local soil type, condition and antenna guying. THUNDERBOLT® Vertical Antennas require a good ground radial system. We recommend a minimum of 32 radials, 65 ft. long, but more radials that are all longer will be more efficient for better signals. Note: For additional information, please look at the files under the "Documentation" tab. Do you want a great Top Band signal? If so, then try one of these DX Engineering 160 Meter THUNDERBOLT® Vertical Antennas!
( 2 )
$1,664.97
DX Engineering HF Vertical Antenna Replacement Parts
DX Engineering's line of HF Vertical Antenna Replacement Parts are offered for you to perform antenna maintenance or repair. DX Engineering has the antenna parts that you need!
( 1 )
$17.49