Availability
11 Results Found For "Stack"
Yaesu G-450ADC Medium-Duty Rotator Systems
Yaesu G-450ADC Medium-Duty Rotator Systems are the entry-level rotator and controller that are perfect for small HF beams, a tri-bander or VHF and UHF antennas up to about 10 sq. ft. of tower-mounted wind load. A lesser wind load of about 5 sq. ft. can be handled when mounting the G-450ADC on top of a mast with the optional lower mast bracket, GC-038. Rotate Amateur and professional antennas with the Yaesu's handsome 120 Vac desktop remote control console, featuring a compass-style indicator at the station operating position. The G-450ADC rotator system provides 450 degrees of azimuth rotation in just over one minute. The rotator handles masts of 1.25 to 2.48 in. outside diameter and, when tower mounted, a total vertical mast load up to 200 lbs. In the Yaesu G-450ADC, the clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-450ADC Rotator motors and controllers operate with a 20 V DC control voltage, four-wire system, using the provided connectors to be installed at each end of the user supplied control cable, same as the previous models. For clarity, the new DC rotator motors are marked "G-450DC" at the connector. The rear panel of the controller is titled "G-450ADC" on the serial number label. WARNING: The legacy Yaesu G-450A Rotator motors and controllers used a 26 VAC control voltage, five-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-450ADC components, which only use pins 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use four-conductor, 20 gauge control cable (4 x 20 AWG). If the rotator cable needs to be longer than 125 ft., then use four-conductor 18 gauge cable (4 x 18 AWG). The input voltage for the G-450ADC controller is labeled "117 VAC" to indicate house current of 110 to 120 Vac. When you need a medium-duty rotator system, which is durable and attractive, order a new Yaesu G-450ADC Medium-Duty Rotator System from DX Engineering.
( 46 )
$429.99
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 20 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-800DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-800DXA Medium Heavy-Duty Rotator System from DX Engineering.
( 23 )
$659.99
Yaesu G-5500DC Azimuth-Elevation Rotator Systems
Yaesu G-5500DC Azimuth-Elevation Rotator Systems are specially designed to accommodate horizontal cross-booms to mount pairs of VHF and UHF directional antennas for space communications. Providing simultaneous control of 450 degrees of azimuth rotation and 180 degrees of elevation rotation, they are perfect for EME (moon bounce) and satellite communications installations. The G-5500DC dual controller lets you adjust and keep track of both aspects of the antenna system's positioning. The 120 VAC controller includes an interface jack for computer control, supported by the optional GS-232A Computer Controller, as well as many aftermarket control programs and interfaces. These azimuth and elevation rotators are actually two separate motor units, now DC controlled. They may be mounted together on a mast with the included mast bracket, or independently with the azimuth rotator inside a tower and the elevation rotator mounted on the mast above the top of the tower. They handle a total of about 10 sq. ft. of antenna wind load and rotate each way in about one minute. The Yaesu G-5500 AZ-EL clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-5550DC azimuth and elevation motors operate with two independent 22 V DC control lines, each a five-wire system, using the same connectors at the end of the control cable as the previous models. Both of the new DC motors, azimuth, and elevation, are marked "G-5550DC" at the connector. Be sure to mark your connectors AZ or EL. The rear panel of the controller is titled "G-5500DC" on the serial number label. WARNING: The legacy Yaesu G-5500 Rotator motors and controller used a 26 VAC control voltage, six-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-5500DC components, which only use pins 1, 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use five-conductor, 20 gauge control cable (5 x 20 AWG). If the rotator cable needs to be longer than 125 ft. then use five-conductor 18 gauge cable (5 x 18 AWG). The input voltage for the G-5500DC controller is labeled "117 VAC" to indicate house current range of 110 to 120 Vac. When you are launching your EME or satellite communications adventure, an azimuth/elevation combination rotator is a vital tool for your antenna system. As durable as they are attractive, Yaesu G-5500DC Azimuth-Elevation Rotator Systems are available from DX Engineering.
( 17 )
$969.99
Yaesu G-1000DXA Heavy-Duty Rotator Systems
Yaesu G-1000DXA Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-1000DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-1000DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 23 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-1000DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-1000DXA Heavy-Duty Rotator System from DX Engineering.
( 14 )
$799.99
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-2800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-2800DXA, G-1000DXA and G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 30 sq. ft. of antenna wind load and over 650 lbs. of vertical mast load. About 130 ft. of control cable is included with the G-2800DXA only. Control console power is 110/120 volts AC. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 50 to 120 seconds on the G-2800DXA, and preset a desired heading for the rotator, to which it then turns automatically. When a fast rotation speed is selected, special "auto slow-start" and "auto slow-stop" features avoid sharp jolts to the antenna array and tower. Activating the rotator causes it to begin turning at slow, but increasing, speed. As the antenna approaches the desired heading, the rotation automatically slows down, before bringing the antenna to a gentle stop. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-2800DXA Extra Heavy-Duty Rotator System from DX Engineering.
( 1 )
$1,769.99
Green Heron RT-21-CDE Universal Digital Rotor Controllers
Green Heron RT-21-CDE Universal Digital Rotor Controllers are completely new, extremely advanced and adaptable controllers for your directional antenna rotation systems. Offering the ultimate in operational capabilities, Green Heron RT-21-CDE Universal Digital Rotor Controllers are the best controllers available for your new rotor unit or as a replacement in existing systems. You can add these great features to your existing rotator unit, without even climbing the tower! * Pre-programmed for Hy-Gain and CDE rotator systems * High-visibility LCD display with adjustable backlight brightness * Fully versatile controls for point-and-shoot or manual push button operation plus presets * Automated rotator computer control through RS-232 or USB * PWM (pulse width modulated) variable-speed control * Start and stop ramping to reduce tower and antenna stresses * Precision heading accuracy up to 1/10 degree * Fully supports side mounted antennas, soft limits prevent running into tower * Allows over-travel up to 720 degrees total * Offset control allows center of rotation at any heading, allows N & S center on same mast, and compensates for slipped mast * Fully user-programmable, reversal and brake delay, speed minimum and maximum, limits, ramps, and much more * Master/slave for stacked arrays, turn together or separately * Counter-rotation, install rotor above rotating tower * Easy front panel setup and setup utility software Replace your old-fashioned rotator controller with a modern, state-of-the-art digital controller! Green Heron RT-21-CDE Universal Digital Rotor Controllers from DX Engineering are pre-programmed specifically for Hy-Gain/CDE HAM-series and T2X (Tailtwister) rotators. However, they are easy to setup for all other rotator units because they are field programmable with convenient, internal, solderless jumpers. Get yours today!
( 6 )
$506.22
—
$649.00
DX Engineering Digital Rotator Controllers
DX Engineering Digital Rotator Controllers are completely new, extremely advanced and adaptable controllers for your directional antenna rotation systems. Offering the ultimate in operational capabilities, the RT-21DXE Digital Rotor Controllers are the best controllers available for your new rotor unit or as a replacement in existing systems. The RT-21DXE comes preset for 24 VDC for operation with the DXE-RT4500HD Heavy Duty Rotator, but they are easily adaptable for use with other directional antenna rotation systems because they are field programmable with convenient, internal, solderless jumpers. Replace your old-fashioned rotator controller with a modern, state-of-the-art digital controller. Order your DXE-RT-21DXE Digital Rotor Controller from DX Engineering today! DXE-RT-21DXE Additional Features and Specifications: You can add these great features to your existing rotator unit, without even climbing the tower! * Preset for 24 VDC for operation with the DXE-RT4500HD Heavy Duty Rotator * High-visibility LCD display with adjustable backlight brightness * Fully versatile controls for point-and-shoot or manual push-button operation plus presets * Automated rotator computer control through RS-232 or USB * PWM (pulse width modulated) variable-speed control * Start and stop ramping to reduce tower and antenna stresses * Precision heading accuracy up to 1/10 degree * Fully supports side-mounted antennas, soft limits prevent running into the tower * Allows over-travel up to 720 degrees total * Offset control allows the center of rotation at any heading, allows N & S center on the mast, and compensates for slipped mast * Fully user-programmable, reversal and brake delay, speed minimum and maximum, limits, ramps, and much more * Master/slave for stacked arrays, turn together or separately * Counter-rotation, install rotor above rotating tower * Easy front panel setup and setup utility software Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
Not Yet Reviewed
$714.99
4O3A Rotator Genius Smart Rotator Controllers
4O3A Rotator Genius Smart Rotator Controllers are a high-precision, network-enabled rotator controllers that use a magnetic sensor to read azimuth. They support control via Windows and Android apps and integrate with the 4O3A Genius ecosystem. Typically mounted at the base of a tower in a waterproof housing or installed in the shack, they are compatible with most rotators and control is provided via LAN, USB, or Wi-Fi. A built-in web interface allows multi-user access and full remote operation. Rotator Genius supports independent control of two rotators, making them suitable for stacked arrays or complex installations.
Not Yet Reviewed
$869.99
Green Heron RT-21-M2 Universal Digital Rotor Controllers
Green Heron RT-21-M2 Universal Digital Rotor Controllers are completely new, extremely advanced and adaptable controllers for your directional antenna rotation systems. Offering the ultimate in operational capabilities, Green Heron RT-21-M2 Universal Digital Rotor Controllers are the best controllers available for your new rotor unit or as a replacement in existing systems. You can add these great features to your existing rotator unit, without even climbing the tower! * Pre-programmed for M2 Antennas rotator systems * High-visibility LCD display with adjustable backlight brightness * Fully versatile controls for point-and-shoot or manual push button operation plus presets * Automated rotator computer control through RS-232 or USB * PWM (pulse width modulated) variable-speed control * Start and stop ramping to reduce tower and antenna stresses * Precision heading accuracy up to 1/10 degree * Fully supports side mounted antennas, soft limits prevent running into tower * Allows over-travel up to 720 degrees total * Offset control allows center of rotation at any heading, allows N and S center on same mast, and compensates for slipped mast * Fully user-programmable, reversal and brake delay, speed minimum and maximum, limits, ramps, and much more * Master/slave for stacked arrays, turn together or separately * Counter-rotation, install rotor above rotating tower * Easy front panel setup and setup utility software Replace your old-fashioned rotator controller with a modern, state-of-the-art digital controller! Green Heron RT-21-M2 Universal Digital Rotor Controllers from DX Engineering are pre-programmed specifically for M2 Antennas rotators. However, they are easy to setup for all other rotator units because they are field programmable with convenient, internal, solderless jumpers. Get yours today!
( 6 )
$649.00
Green Heron RT-21D-CDE Deluxe Universal Digital Rotor Controllers
Green Heron RT-21D-CDE Deluxe Universal Digital Rotor Controllers have a new green vacuum fluorescent display and a black front panel. The new deluxe version builds upon the excellent design of the RT-21 with higher resolution when using the Point and Shoot Knob. Offering the ultimate in operational capabilities, Green Heron RT-21D-CDE deluxe universal digital rotor controllers are the best controllers available for your new or existing directional antenna rotor unit or rotation systems. Replace your old-fashioned rotator controller with a modern, state-of-the-art digital controller! Green Heron RT-21D-CDE Deluxe Universal Digital Rotor Controllers from DX Engineering are pre-programmed specifically for Hy-Gain/CDE HAM-series and T2X (Tailtwister) rotators. However, they are easy to setup for all other rotator units because they are field programmable with convenient, internal, solderless jumpers. You can add these great features to your existing rotator unit without even climbing the tower! * Pre-programmed for Hy-Gain and CDE rotator systems * New high-visibility green vacuum fluorescent display with adjustable brightness * Custom black front panel * Fully versatile controls for point-and-shoot or manual push button operation plus presets * Automated rotator computer control through RS-232 or USB * PWM (pulse width modulated) variable-speed control * Start and stop ramping to reduce tower and antenna stresses * Precision heading accuracy up to 1/10 degree * Fully support side mounted antennas, soft limits prevent running into tower * Allow over-travel up to 720 degrees total * Offset control allows center of rotation at any heading, allows N and S center on same mast, and compensates for slipped mast * Fully user-programmable, reversal and brake delay, speed minimum and maximum, limits, ramps, and much more * Master/slave for stacked arrays, turn together or separately * Counter-rotation, install rotor above rotating tower * Easy front panel setup and setup utility software Green Heron RT-21D-CDE Deluxe Universal Digital Rotor Controllers will get your antenna system operational again or add advanced features your old controller lacked. Order from DX Engineering… today!
Not Yet Reviewed
$759.00
Green Heron RT-21D-M2 Deluxe Universal Digital Rotor Controllers
Green Heron RT-21D-M2 Deluxe Universal Digital Rotor Controllers have a new green vacuum fluorescent display and a black front panel. The new deluxe version builds upon the excellent design of the RT-21 with higher resolution when using the Point and Shoot Knob. Offering the ultimate in operational capabilities, Green Heron RT-21D-M2 deluxe universal digital rotor controllers are the best controllers available for your new or existing directional antenna rotor unit or rotation systems. Replace your old-fashioned rotator controller with a modern, state-of-the-art digital controller! Green Heron RT-21D-M2 Deluxe Universal Digital Rotor Controllers from DX Engineering are pre-programmed specifically for M2 Antennas rotators. However, they are easy to set up for all other rotator units because they are field programmable with convenient, internal, solderless jumpers. You can add these great features to your existing rotator unit without even climbing the tower! * Pre-programmed for M2 Antennas rotator systems * New high-visibility green vacuum fluorescent display with adjustable brightness * Custom black front panel * Fully versatile controls for point-and-shoot or manual push button operation plus presets * Automated rotator computer control through RS-232 or USB * PWM (pulse width modulated) variable-speed control * Start and stop ramping to reduce tower and antenna stresses * Precision heading accuracy up to 1/10 degree * Fully support side mounted antennas, soft limits prevent running into tower * Allow over-travel up to 720 degrees total * Offset control allows center of rotation at any heading, allows N and S center on same mast, and compensates for slipped mast * Fully user-programmable, reversal and brake delay, speed minimum and maximum, limits, ramps, and much more * Master/slave for stacked arrays, turn together or separately * Counter-rotation, install rotor above rotating tower * Easy front panel setup and setup utility software Green Heron RT-21D-M2 Deluxe Universal Digital Rotor Controllers will get your antenna system operational again or add advanced features your old controller lacked. Order from DX Engineering… today!
Not Yet Reviewed
$759.00