Selected Filters


Availability


9 Results Found For "Choke"

Part Groups

Results 1 - 9 of 9

DX Engineering TWIG QRP Monoband Dipole Antenna Kits

DX Engineering TWIG QRP Monoband Dipole Antenna Kits provide everything needed to build a lightweight, low-power (QRP) standard Dipole antenna using the DXE-TWIG-1-1 QRP Choke Balun. Designed for portable operating, these kits make it easy to assemble an efficient monoband dipole antenna for outdoor activities such as POTA® and SOTA®, as well as other field and portable operations. This antenna kit comes with enough wire to operate on any single band, 40 through 10-meters, depending upon the length of wire cut for both legs of the dipole according to the included instructions. When properly constructed and supported with the center feedpoint at least 15 feet above ground, this antenna is rated for 25 watts SSB, 10 watts CW, and 5 watts digital modes. DX Engineering TWIG QRP Monoband Dipole Kits Include: • (1) DXE-TWIG-1-1 QRP Choke Balun • (2) DXE Lightweight Wire Winders • (2) End Insulators • (4) Bongo Ties • (3) Hanging Clips • (2x35ft.) 24 AWG PVC Insulated High-Viz Yellow Antenna Element Wire •(1) Instruction Manual

Not Yet Reviewed

$79.99

DX Engineering TWIG QRP Off Center Fed Dipole Kits

DX Engineering TWIG QRP Off Center Fed Dipole Kits provide everything needed to build lightweight, low-power (QRP) Off Center Fed Dipole (OCF) antennas around the DXE-TWIG-4-1C QRP Current Balun. Designed for portable operating, these kits make it easy to assemble efficient multiband antennas for outdoor activities such as POTA® and SOTA®, as well as other field and portable operations on the 40 through 10-meter amateur bands. When properly constructed, these antennas are rated for 25 watts SSB, 10 watts CW, and 5 watts digital modes. At the heart of these kits is the included DXE-TWIG-4-1C balun, which features a 4:1 transformer that converts the approximately 200-ohm impedance of an OCF antenna to the desired 50-ohm impedance required by standard coaxial feedlines. A BNC female connector provides compatibility with recommended coaxial cables and most QRP transceivers. When installed correctly and tuned to the desired operating bands, the included 24 AWG PVC-insulated, stranded copper, high-visibility yellow antenna wire typically eliminates the need for an external antenna tuner. This reduces the amount of gear operators need to carry into the field while allowing for quick band changes and improved operating efficiency. For best performance, a coaxial feedline with BNC connectors (sold separately) measuring approximately 25 to 35 feet is recommended. These antennas can be deployed in a variety of configurations, with final wire lengths varying based on the installation method and operating requirements.

Not Yet Reviewed

$77.99

DX Engineering TWIG End Fed Half Wave QRP Antenna Feedpoint Kits

DX Engineering TWIG End Fed Half Wave QRP Antenna Feedpoint Kits are a compact, essential component for building a low-power (QRP) end-fed half-wave antenna system. Perfect for portable operations and outdoor activities such as POTA® or SOTA™, this feedpoint kit simplifies setup while delivering reliable performance. The TWIG is rated for 25W SSB, 10W CW, and 5W Digital modes, delivering an SWR of less than 2:1 without an antenna tuner. At its core, the TWIG features a 49:1 transformer that matches the impedance of the user supplied half-wave element wire to 50-ohms, ensuring compatibility with most QRP transceivers. The BNC female connector pairs easily with recommended coax cables, and when the element wire is properly tuned, no external tuner is required—reducing the amount of gear you need to carry. The kit includes a built-in quick connector designed for 24/26 AWG antenna wire, making element installation fast and secure. Two end insulators and clips are also provided, ensuring reliable strain relief and easy attachment of the antenna wire in the field. Installation is quick and straightforward, allowing you to get on the air fast and start making contacts. No additional counterpoise wire is necessary; the coax cable serves that function when installed correctly. For best results, use optional 24/26 AWG wire such as CEW-VIZ24-YEL100, a high-visibility, PVC-insulated stranded copper wire. A typical setup uses a sloper configuration, with the feedpoint about 6–7 feet above ground and the wire sloping upward to 25–30 feet. Recommended coax length is 25–35 feet with BNC connectors and adding an optional DXE-LPFC-BNC Feedline Choke at the transceiver end is suggested. While the antenna supports multiple configurations, wire length will vary based on installation.

5.0 out of 5 stars ( 1 )

$49.99

DX Engineering TWIG End Fed Half Wave QRP Antenna Kits

DX Engineering TWIG End Fed Half Wave QRP Antenna Kits include the essential components needed to build a lightweight, low-power (QRP) end-fed half-wave antenna for portable and field operations. Ideal for activities such as POTA® and SOTA™, these kits are designed for quick deployment, efficient operation, and minimal equipment requirements. When properly assembled and tuned, TWIG End Fed Half Wave QRP antennas deliver an SWR of less than 2:1 without the need for an antenna tuner and are rated for 25 watts SSB, 10 watts CW, and 5 watts digital modes. At the heart of these kits is a 49:1 transformer that matches the high feedpoint impedance of the half-wave radiator to a standard 50-ohm coaxial feedline. The integrated BNC female connector is compatible with recommended coaxial cables and most QRP transceivers. Once the included antenna wire is properly tuned for the desired operating band, an external tuner is typically unnecessary, reducing pack weight and simplifying field operation. No separate counterpoise wire is required, as the coaxial feedline serves this function when installed correctly. To simplify assembly and deployment, the kits feature a built-in quick-connect wire terminal designed for use with the included 24 AWG antenna wire. Two end insulators and attachment clips are also included to provide secure strain relief and convenient field installation. A DX Engineering wire winder and reusable Bongo ties help keep the antenna organized and compact when stored or transported. A typical installation uses a sloper configuration, with the feedpoint positioned approximately 6 to 7 feet above ground level and the antenna wire extending upward to a height of 25 to 30 feet. For optimum performance, a 25- to 35-foot coaxial feedline with BNC connectors is recommended. An optional DXE-LPFC-BNC Feedline Choke installed at the transceiver end of the coax is also recommended to help minimize common-mode current. While the antenna can be deployed in a variety of configurations, final wire lengths may vary depending on the installation method and operating requirements. User assembly is required. Recommended tools and materials include wire cutters, a tape measure, 3/16-inch diameter rope to hang the antenna, electrical tape, a suitable throwing weight for antenna installation, and an antenna analyzer for trimming and tuning the antenna element to the desired operating band.

Not Yet Reviewed

$77.99

EAntenna Sloper Antennas

The EAntenna Slopers are shortened with a coil to reduce the antenna length, but behave like quarter-wave sloper antennas. Like any Sloper antenna, it is directional with a low angle for excellent long range DX results. Directivity is away from the supporting metal mast or tower, toward the lower end of the sloper. If a non-metallic vertical support is used for the sloper, an additional vertical wire counterpoise is required. The antenna wire is 2mm (approx. 12 AWG) with UV-resistant insulation for durability. This antenna does not include a balun, but use with a feedline choke, line isolator, or coax bead choke is recommended to achieve the desired results. These antennas are rated for 2 kW CW. The EAntenna EASLP160S achieves a considerable 2:1 SWR bandwidth of 75 kHz. The EAntenna EASLP80S achieves a respectable 2:1 SWR bandwidth of 210 kHz. The assembly and deployment of this antenna is simple. The feedpoint of the antenna is attached to the mast or tower at the minimum height listed below, or higher, if possible, for better results. If supported by a tree, this antenna requires a grounded vertical wire counterpoise, in addition to the coax feedline. With antenna support rope, extend the insulated end to a support a minimum of 10 ft. above the ground. This antenna is preset to the bottom of the band. Adjust to higher frequencies within the band with 5 cm (2 in.) cuts for gradual changes while using an antenna analyzer. In just 5 minutes you can prune the antenna to cover the desired portion of the band. Physical Characteristics of the EAntenna Slopers: * EASLP160 Total Length: 17.7m (58.0 ft.); Minimum Height: 12.7m (41.6 ft.) * EASLP80 Total Length: 11.0m (36.0 ft.); Minimum Height: 8.0m (26.2 ft.)

5.0 out of 5 stars ( 2 )

$122.99

—

$161.99

Alpha Delta SEP Arc-Plug® Static Electricity Protectors

Alpha Delta SEP Arc-Plug® Static Electricity Protectors are mounted in the DELTA-C Center Insulator and bleed off slow-rising static electricity charges by routing them harmlessly to ground, before they can enter the shack through the feedline. This method is far more effective than DC-grounded baluns or chokes, which can be "popped" by static charges. Dangerous static charges are developed from thunderstorms, high-wind driven snow, or desert sand. The static electricity generated by these forces has been measured to thousands of volts. They're so potent; they can puncture the dielectric of unterminated coax. Alpha Delta SEP Arc-Plug® units are OEM replacements for the protectors located in the back of DELTA-C Center Insulators and are easily replaced by carefully removing the #10 stainless steel hardware used to attach the ends of the antenna wires. Please note the assembly order of your washers, lock washers, wires, nuts, and carefully re-assemble them in the same order after replacing the static electricity protector cartridge. Keep antenna-produced static electricity out of your receiver or transceiver. Order Alpha Delta SEP Arc-Plug® Static Electricity Protectors from DX Engineering and keep a few on hand!

3.67 out of 5 stars ( 3 )

$19.99

SOTAbeams Antenna Center and 4:1 Transformers

SOTAbeams Antenna Center and 4:1 Transformers are a very handy feed point for a low-power lightweight portable HF doublet antenna project. Available as a kit (SBM- ACBA-101) or already built (SBM-ACBA-102). These are very versatile dipole center insulators that include these outstanding features: • Coaxial Cable Strain-Relief Built In • BNC female Connector • Water-Resistant Construction with Integral UV Resistant Cover • Antenna Wire Strain-Relief Built-in • Binding Posts for Antenna Wire Connections • Mounting Holes for Center Support Rope • Lightweight – 3.1 oz. (88g) • High Performance by Design - Flat Response from 3-30MHz • Loss: < 0.2dB @ 14MHz • Matched SWR < 1.15:1 1.8-30MHz (< 1.50:1 0.5-60MHz) • Power Rating: 125W SSB-CW; 30W Digital The SOTAbeams Antenna Center and 4:1 Transformers are useful for pre-matching higher impedance antenna systems such as doublets and folded dipoles to bring the SWR into the matching range of internal antenna tuners. In that application, the length of the feeder between the transformer and the tuner must be kept to about 6 ft. These Antenna Centers have a 4:1 matching transformer that is sometimes referred to as a balun. This isn't a choke, so strictly speaking it's not a choke balun, but it's typically referred to as a voltage balun. This transformer is designed with a lip that can be sealed using a silicone sealant if required for use in more permanent installations. We do not supply the Balun sealed as this allows users to gain access to the enclosure and allow any buildup of moisture to drain away. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.

Not Yet Reviewed

$25.99

—

$45.99

Alpha Delta Parallel Wire Sloper Antennas

Alpha Delta Parallel Wire Sloper Antennas are designed for limited-space installations that don't allow for the DX-A twin sloper antennas. These antennas have a 50 ohm coax feed and are rated for full legal power. They are designed to use your tower or other antenna support structure. Requiring only 60 ft. of overall length, they provide amazing DX performance at installation heights of only 35 ft. at the high end and 8 ft. at the low end. These antennas are pre-assembled and pre-tuned for an easy installation. DX-B sloper antennas cover 160, 80, 40 and 30 meters. The "top wire" covers 160, 80 and 40 meters. The parallel "underslung" wire covers 30 meters and may be removed or trimmed to 20 meters if desired. Parallel sloper antennas utilize stainless steel hardware, 12-gauge solid copper wire, and efficient Alpha Delta "Iso-Res" RF choke coils. To gain the same broadband performance as the DX-As, the DX-Bs are also designed to be used with a wide-range antenna tuner, so no trimming or tweaking is necessary. Here's an efficient and compact antenna for 160, 80, 40 and 30 or 20 meters. Order your Alpha Delta Parallel Wire Sloper Antennas from DX Engineering!

5.0 out of 5 stars ( 2 )

$159.99

Alpha Delta Twin Sloper Antennas

Alpha Delta Twin Sloper Antennas combine the tremendous DX firepower of the quarter wave sloper with the wide bandwidth of the half wave dipole. These model DX-A twin slopers are designed to cover 160, 80 and 40 meters. One leg is 67 ft. long, while the other is 60 ft. long. The sloper antennas install like an inverted-V with ground return accomplished through the tower or down-lead. These antennas utilize stainless steel hardware, 12-gauge solid copper wire, and efficient Alpha Delta "Iso-Res" RF choke coils. Twin sloper antennas are designed for use on an un-guyed metal tower with a beam on top. The beam provides a capacity hat effect and helps to tune the twin slopers. NOTE: It is possible that the introduction of the sloper antennas into a tower system employing multiple guy wires or other attached wire antennas may cause a slight detuning of the sloper antennas. Other installation types will require the use of an outboard wide-range antenna tuner. Time-proven antennas are always good values. Order Alpha Delta Twin Sloper Antennas from DX Engineering and enjoy some vintage wire antenna performance!

5.0 out of 5 stars ( 1 )

$154.99

  • 1
  • Page 1 of 1