Antennas
Availability
Antennas for HAM Radio
Monoband or multi-band. Vertical or directional. Base or mobile. Transmitting or receiving. No matter what type of antenna or antenna system you need, you’ll find it...
Monoband or multi-band. Vertical or directional. Base or mobile. Transmitting or receiving. No matter what type of antenna or antenna system you need, you’ll find it at DX Engineering. Choose from a wide range of antenna types, including single-band, dual-band, multi-band, vertical, trap vertical, wire, Yagi, VHF/UHF and HF/VHF mobile, and more. DX Engineering receive antenna systems feature the best designs available for HF DXing, as well as for “AM DXing” on the MW Broadcast Band and for the Short Wave Listening bands (SWL). Maximize your signal and minimize noise with antenna accessories such as antenna switches, vertical...
Monoband or multi-band. Vertical or directional. Base or mobile. Transmitting or receiving. No matter what type of antenna or antenna system you need, you’ll find it at DX Engineering. Choose from a wide range of antenna types, including single-band, dual-band, multi-band, vertical, trap vertical, wire, Yagi, VHF/UHF and HF/VHF mobile, and more. DX Engineering receive antenna systems feature the best designs available for HF DXing, as well as for “AM DXing” on the MW Broadcast Band and for the Short Wave Listening bands (SWL). Maximize your signal and minimize noise with antenna accessories such as antenna switches, vertical add-on kits, variable phasing controllers, baluns, radial and tilt base plates, preamplifiers, and more. Fortify your existing antenna or build your own with high-quality brackets, clamps, tubing and supports from DX Engineering. Shop here for HAM radio antennas, antenna systems, and antenna components from the best: DX Engineering, Cushcraft, Hy-Gain, Hustler, COMTEK SYSTEMS, Diamond Antenna, and more!
QRO.cz Stack Match High Power Broadband Antenna Phasing Switches
QRO.cz Stack Match High Power Broadband Antenna Phasing Switches are high-performance broadband antenna combiner designed to impedance match two Yagi antennas to a single transceiver (TRX). Ideal for mono-band, tri-band, or multi-band antenna systems, they support both in-phase (BiP) and out-of-phase (BoP) configurations, enabling advanced stacking and phasing configurations. Whether you're optimizing a contest station or enhancing DX performance, these Stack Match 1-2 switches allow seamless switching between upper, lower, BiP, and BoP modes. Built with high-quality components and housed in a rugged aluminum enclosure makes them a reliable choice for demanding HF operations.
Not Yet Reviewed
$559.99
DX Engineering PRO-STACK Broadband Antenna Phasing Switches
DX Engineering PRO-STACK Broadband Antenna Phasing Switches are newly designed to combine two identical Yagi or log periodic beams, or three quarter-wave vertical antennas, into a phased array for enhanced operation. There is no need for coaxial delay lines with the DX Engineering PRO-STACK switches. Just connect your antennas to the phasing switch controller with equal-length 50 ohm lines. PRO-STACK switch units are available with high-quality PTFE-silver plated SO-239 (UHF female) connectors. These relay units are 1-of-3 source voltage controlled at 12-15VDC over a four conductor cable. A matching Control Console is available separately or is included in the PRO-STACK System. These phasing switches can be used for any applications that require the following four basic antenna feed selections: both antenna ports in-phase, both antenna ports out-of-phase, antenna port 1 only, and antenna port 2 only. The default is both output ports in-phase. Impedance matching automatically changes when any antenna port is disconnected. Generally, stacked Yagi antennas are separated vertically greater than 1/2-wavelength free space. Since the DX Engineering PRO-STACK Broadband Antenna Phasing Systems are broadband, they may be easily adapted to larger arrays. For example, four stacked Yagis may be combined by creating two sets of two, and then using a third DX Engineering control console to combine the first two sets. PRO-STACK switches can also be used to feed three quarter wave resonant vertical antennas for a high-gain 4-pattern array. In this arrangement, the center #2 passive element is directly grounded to a good ground radial system at all times, while the end elements #1 and #3 are then fed in various phase relationships by the PRO-STACK. Details are in the complete PRO-STACK PS-2B Instruction Manual linked here in Documentation. Features of the DX Engineering PRO-STACK Broadband Antenna Phasing Switches include these great features: * Power handling up to 5 kW * Broadband coverage on 160-10 meters * High-impact RF shielded weatherproof housing * High-RF tolerant, silver-PTFE SO-239 (UHF female) connectors * Proven DX Engineering RF relays for high performance * Safe 12 VDC relay operation, even on battery or solar power * MOV surge protection on control lines * External, removable control line connector * RoHS-compliant assembly
( 1 )
$699.99
—
$740.00
M2 Antennas HO LOOP Stacking Kits
M2 Antennas HO LOOP Stacking Kits provide the parts for vertical stacking of two HO LOOP antennas, to achieve an additional 3 dB gain. Stacking two loops at sufficient height above the ground will focus your VHF or UHF horizontally polarized omnidirectional signal toward the horizon, so you can make more contacts with more distant stations! You can expect better long haul tropo range with two HO LOOPS and HO LOOP stacking kits. HO LOOP Stacking Kits contain phasing lines, "T" junction block, upper and lower small mast sections. The HO LOOP Antennas are purchased separately, as are the appropriate base or mobile installation mounts. Get your HO LOOP Stacking Kits form DX Engineering today!
( 2 )
$332.99
DX Engineering PRO-STACK Broadband Antenna Phasing Systems
DX Engineering PRO-STACK Broadband Antenna Phasing Systems are designed to combine two identical Yagi or log periodic beams, or three quarter-wave vertical antennas, into a phased array for enhanced directional pattern selections and dramatically improved HF operations. There is no need for special coaxial delay lines with the DX Engineering PRO-STACK systems. Just connect your antennas to the system relay unit with equal-length 50-ohm coaxial cable assemblies. The PRO-STACK switch relay units are available with high-quality PTFE-silver plated SO-239, UHF female connectors. The matching PRO-STACK Control Console operates the system with a 1-of-3 source voltage control format at 12-15V DC with a user supplied four conductor control cable to achieve four different antenna phasing selections. PRO-STACK Broadband Antenna Phasing Systems operate across the 160 to 10 meter range. They have two antenna ports that can be used for any application requiring the four basic selections: 1. BIP - Both antenna ports In-Phase 2. BOP - Both antenna ports Out-of-Phase 3. BOTTOM - Antenna port 1 only 4. TOP - Antenna port 2 only. The unpowered default is 1 - Both ports In-Phase. Impedance matching is automatic in the PRO-STACK even when any antenna port is disconnected. Generally, stacked Yagi antennas are separated vertically with greater than one half wavelength free space. Since the DX Engineering PRO-STACK Antenna Phasing Systems are broadband, they may be easily adapted to larger arrays. For example, four stacked Yagis may be combined by creating two sets of PRO-STACKS, with a third DX Engineering PRO-STACK to combine the first two. PRO-STACK systems may also be used to feed quarter-wave resonant vertical antennas for a high-gain, 4-pattern array. This arrangement requires three verticals, with the center #2 passive antenna element directly grounded to the system ground radial system at all times, while elements #1 and #3 are then fed in various phase relationships by the PRO-STACK. Details are in the complete PRO-STACK PS-2B Instruction Manual linked here in "Documentation" tab. The full- color printed manual is included with the system relay unit. PRO-STACK Broadband Antenna Phasing Systems are available as separate Relay Units for operators who have automated BCD switching devices, and as packaged systems with Relay Unit and matching manual Control Console. Features of the DX Engineering PRO-STACK Broadband Antenna Phasing Systems include: * Power handling up to 5 kW * Broadband coverage on 160-10 meters * High impact shielded weatherproof housing * High-RF tolerant, silver-PTFE SO-239 (UHF female) connectors * Proven DX Engineering RF relays for high performance * Safe 12V relay operation * DC-powered control console allows battery or solar emergency operation * MOV surge protection on control lines * External, removable control line connector * RoHS-compliant assembly Dominate the airwaves with DX Engineering PRO-STACK Broadband Antenna Phasing Systems. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$895.98
—
$935.99
Clearance
COMTEK Stack 3 Yagi Switch Control Consoles
COMTEK Stack 3 Yagi Switch Control Consoles are available as replacements for Stack 3 Yagi Systems. When connected to the Stack 3 Switch Relay Unit, these control consoles allow you to select one antenna, all antennas, or any combination of two antennas. Indicator lights for each antenna tell you at a quick glance which antennas are selected. Choose either 115 V AC or 12 V DC control console operation. Keep using your Yagis together! Order COMTEK Stack 3 Yagi Switch Control Consoles from DX Engineering!
Not Yet Reviewed
$124.99
—
$125.99
$56.25
—
$63.00
DX Engineering PRO-STACK 2 Control Consoles
DX Engineering PRO-STACK 2 Control Consoles are designed for use with DX Engineering PS-2 and PS-2B switches. They require 12 Vdc well-filtered at 2 amps (fused) minimum.
( 1 )
$195.99
DX Engineering PS-3B PRO-STACK Three Antenna Phasing Units
DX Engineering PS-3B PRO-STACK Three Antenna Phasing Units offer the ultimate performance for combining three identical Yagi or Log Periodic directional antennas and may be used for vertical antennas in a phased array that cover any band, from 160 through 10 meters. Pro-Stack frequency independent broadband phasing devices operate optimally with three properly spaced mono-band antennas, but can be used with three identical stacked multi-band beam antennas, for pattern and null steering that wins contests and snags the rarest DX! Signals arrive at your antenna system from different azimuth directions and different elevation angles. Adding a stacking phasing system to a rotational array adds the ability to steer the pattern of the antenna array in two planes, azimuth and elevation, and to move the major lobe and nulls. The greatest advantage of Pro-Stack arrays is the ability to move harmful pattern nulls away from signal arrival angles. While gain makes a marginal improvement, moving a 20 to 40 dB null can be a phenomenal change, so the Pro-Stack can make the difference between a barely readable and a strong signal, providing the performance edge needed to work rare DX - and win contests. DXE-PS-3B Pro-Stack Phasing Units are 50 ohm relay systems that handle up to 5 kW. A separate user-supplied automated controller or the optional DX Engineering DXE-EC-PS3 Control Console for these 12-position rotary switch selections: - Three antenna ports in phase, default with no power to control console. - Antenna port 1 only - Antenna port 2 only - Antenna port 3 only - Port 2 out of phase, Port 3 in phase - Port 1 out of phase, Port 3 in phase - Port 1 out of phase, Port 2 in phase - Ports 2 and 3 in phase - Ports 1 and 3 in phase - Ports 1 and 2 in phase - Ports 1 and 2 in phase, Port 3 out of phase - Ports 1 and 3 in phase, Port 2 out of phase - Port 1 out of phase, Ports 2 and 3 in phase These PRO-STACK units may also be used for other applications requiring these feedline selections. To ensure lowest SWR, impedance matching automatically changes when any antenna is disabled. By switching between antennas at different heights above ground and/or changing the phase relationship between multiple antennas. The old standard system in stacks was to activate or disable specific antennas in the stack to change pattern. However, with the Pro-Stack system, gain remains higher when all antennas are driven and phase is changed, plus this system allows phase inversion as well as the ability to switch any single antenna out of the array. DXE-PS-3B Broadband Phasing Units provide the greatest flexibility for three identical antennas. This relay unit contains a broad-bandwidth high-power 2:1 impedance matching transformer. This eliminates common requirements of using mixtures of 75 ohm and 50 ohm phasing or delay cables for impedance matching. Feedlines to each antenna from the relay unit must be the same cable of the same length and match the antenna impedance. DXE-PS-3B Pro-Stack Broadband Three Antenna Phasing Units feature: - Power Handling up to 5 kW - Broad band coverage on 160-10 meters - RF Shielded Weatherproof Housing - unique protection - DXE-PS-3B has High-RF tolerant, silver - PTFE UHF connectors - DXE-PS-3BDIN has Amphenol Connex 7/16 DIN Panel Connectors - DXE-PS-3BN-P are made with high-quality silver-PTFE Type N female connectors - Proven high current DX Engineering RF Relays - Safe 12 volt dc relay operation - MOV surge protection on control lines - RoHS compliant assembly Get a DX Engineering PS-3B PRO-STACK Three Antenna Phasing System for your winning antenna array.
Not Yet Reviewed
$895.99
—
$999.99
DX Engineering PS-3B PRO-STACK Three Antenna Phasing System
Dominate the airwaves with a DX Engineering PS-3B PRO-STACK Three Antenna Phasing System. Achieve ultimate array control and performance with three identical Yagi or Log Periodic directional antennas or use the system for vertical antennas in a phased array. DXE-PS-3B Pro-Stack Units are frequency independent broadband phasing devices that operate with three antennas on any bands, from 160 through 10 meters. Select from twelve combinations of in-phase and out-of-phase for pattern and null steering that wins contests and snags the rarest DX! DXE-PS-3B-P PRO-STACK Three Antenna Phasing Systems consist of one DXE-PS-3B Relay Unit and one DXE-EC-PS3 Control Console with manual 12-position rotary switch. This advanced system requires only 9-conductor control cable and standard 50-ohm feedlines of equal lengths to each antenna. DXE-PS-3B Pro-Stack Broadband Three Antenna Phasing Systems offer these compelling features: - Power Handling up to 5 kW - Broad band coverage on 160-10 meters - RF Shielded Weatherproof Housing - unique protection - DXE-PS-3B has High-RF tolerant, silver - PTFE SO-239 (UHF female) connectors - DXE-PS-3BN-P are high-quality silver-PTFE Type N female connectors - DXE-PS-3BDIN has Amphenol Connex 7-16 DIN Panel Connectors - Proven high current DX Engineering RF Relays - Safe 12 volt DC relay operation - MOV surge protection on control lines - RoHS compliant assembly DXE-PS-3B Broadband Phasing Units provide the greatest flexibility for three identical antennas. This relay unit contains a broad-bandwidth high-power 2:1 impedance matching transformer. This eliminates common requirements of using mixtures of 75 ohm and 50 ohm phasing or delay cables for impedance matching. Feedlines to each antenna from the relay unit must be the same cable of the same length and match the antenna impedance. So all of them need only be as long as the longest, to reach from the antennas to the relay unit. While it is best to have feedlines of equal electrical lengths, there is no need to closely phase-match cables; cutting the antenna feedlines made from the same coax to equal physical lengths is sufficient. To ensure lowest SWR, impedance matching automatically changes when any antenna is disabled. By switching between antennas at different heights above ground and/or changing the phase relationship between multiple antennas. The old standard system in stacks was to activate or disable specific antennas in the stack to change pattern. However, with the Pro-Stack system, gain remains higher when all antennas are driven and phase is changed, plus this system allows phase inversion as well as the ability to switch any single antenna out of the array. Signals arrive at your antenna system from different azimuth directions and different elevation angles. Adding a stacking phasing system to a rotational array adds the ability to steer the pattern of the antenna array in two planes, azimuth and elevation, and to move the major lobe and nulls. This is accomplished by switching between three identical antennas that are properly spaced for phasing, as well as changing the phase relationship between the antennas to effect changes in the null positons of their elevation patterns. The greatest advantage of equipping your array with a DX Engineering Pro-Stack is the ability to move debilitating pattern nulls away from signal arrival angles. While gain makes a marginal improvement, moving a 20 to 40 dB null can make a phenomenal change in reception. So, the Pro-Stack can make the difference between a barely readable and a strong signal, thus providing the performance edge needed to work rare DX - and win contests. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Get a DX Engineering PS-3B PRO-STACK Three Antenna Phasing System for your winning antenna array.
( 1 )
$1,101.98
—
$1,205.98
DX Engineering PRO-STACK 3 Control Consoles
DX Engineering PRO-STACK Three Antenna Control Consoles, model DXE-EC-PS3, are custom made twelve-position rotary switch controls for manual operation of PRO-STACK Broadband Three Antenna Phasing Relay Units, models DXE-PS-3B and DXE-PS-3BDIN. DXE-EC-PS3 Control Consoles offer the following features: * Stainless Steel Housing * Non-Skid feet * On-Off toggle switch * Green LED power on indicator * Filter capacitors on each control line * Internal automatic resettable fuse * Includes a 2.1mm power plug for +12 V DC power connection Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DXE-EC-PS3 Control Consoles connect to the PRO-STACK Relay Units with 9-conductor control cable, or with 8-conductor cable plus ground using the coaxial cable shield as the ground return. These consoles were designed for the PS-3B series, but may be used for other applications which require a special BCD controller. See the EC-PS3 manual linked in the "Documentation" tab for detail on connections and the BCD truth table.
Not Yet Reviewed
$205.99
Clearance
COMTEK Stack 2 Yagi Switch Control Consoles
COMTEK Stack 2 Yagi Switch Control Consoles are designed for use with newer or older COMTEK Stack 2 systems. These are the control consoles, only. They include a 2.1mm power cord and operate on 12V DC. Station power, if used, must be 12V DC at 1A minimum (fused). A 3-conductor control line between the control console and relay unit is required. Whether you are replacing a damaged console or building a new system from parts, these COMTEK Stack 2 Yagi Switch Control Consoles from DX Engineering are what your stacking system needs!
Not Yet Reviewed
$124.99
$50.00
Hamplus Four Stack II Systems
Hamplus Four Stack II Systems makes it possible to easily and quickly change selections of any in-phase combination of two, three, or four stacked HF beam antennas or an array of HF phased vertical antennas. Plus, Four Stack II Systems can be combined to control antenna selections on any of the array switches by any of the multiple system Control Consoles. This is possible with simple patch cable networking. Up to four operating positions can have access to four different stacked arrays. The Hamplus Four Stack II System provides unprecedented control of your multiple antenna arrays. The 4-Stack Control Console has five illuminated pushbuttons; ANT 1 through 4 select stacked antennas and ENTER aids in programming. Each antenna selection keys works as a one-touch ON, one-touch OFF method, so it is easy to control which of antennas you want to use at a certain time. Trying different combinations of antennas for the transmission and reception can be accomplished independently, quickly and easily. Arrays can be configured differently for receive and transmit without manually switching back and forth. The system is managed and supervised by a microcontroller that has internal software designed to meet the various system functions and easy operation. All control boxes can be interconnected so that any remote console can command any antenna array switch box. The Four Stack II switch box is rugged and capable, with a better design for mounting outdoors, near or under antenna arrays. No extra or special housings are needed. With the internally connected controller cable, the system is an easy, plug-and-play operation. The Four Stack II is available with either Type N female or UHF female (SO-239) connectors for your array. The Four Stack II is rated for 3,000 W maximum RF power and covers 1.8 to 30 MHz. Connection to 50 ohm, low SWR antennas with 50 ohm coaxial cable is required. All combinations of antennas are in-phase only. Achieve complete control of your antenna arrays with Hamplus Four Stack II Stack Systems from DX Engineering!
Not Yet Reviewed
$899.99
Yaesu G-450ADC Medium-Duty Rotator Systems
Yaesu G-450ADC Medium-Duty Rotator Systems are the entry-level rotator and controller that are perfect for small HF beams, a tri-bander or VHF and UHF antennas up to about 10 sq. ft. of tower-mounted wind load. A lesser wind load of about 5 sq. ft. can be handled when mounting the G-450ADC on top of a mast with the optional lower mast bracket, GC-038. Rotate Amateur and professional antennas with the Yaesu's handsome 120 Vac desktop remote control console, featuring a compass-style indicator at the station operating position. The G-450ADC rotator system provides 450 degrees of azimuth rotation in just over one minute. The rotator handles masts of 1.25 to 2.48 in. outside diameter and, when tower mounted, a total vertical mast load up to 200 lbs. In the Yaesu G-450ADC, the clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-450ADC Rotator motors and controllers operate with a 20 V DC control voltage, four-wire system, using the provided connectors to be installed at each end of the user supplied control cable, same as the previous models. For clarity, the new DC rotator motors are marked "G-450DC" at the connector. The rear panel of the controller is titled "G-450ADC" on the serial number label. WARNING: The legacy Yaesu G-450A Rotator motors and controllers used a 26 VAC control voltage, five-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-450ADC components, which only use pins 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use four-conductor, 20 gauge control cable (4 x 20 AWG). If the rotator cable needs to be longer than 125 ft., then use four-conductor 18 gauge cable (4 x 18 AWG). The input voltage for the G-450ADC controller is labeled "117 VAC" to indicate house current of 110 to 120 Vac. When you need a medium-duty rotator system, which is durable and attractive, order a new Yaesu G-450ADC Medium-Duty Rotator System from DX Engineering.
( 46 )
$429.99
Yaesu G-5500DC Azimuth-Elevation Rotator Systems
Yaesu G-5500DC Azimuth-Elevation Rotator Systems are specially designed to accommodate horizontal cross-booms to mount pairs of VHF and UHF directional antennas for space communications. Providing simultaneous control of 450 degrees of azimuth rotation and 180 degrees of elevation rotation, they are perfect for EME (moon bounce) and satellite communications installations. The G-5500DC dual controller lets you adjust and keep track of both aspects of the antenna system's positioning. The 120 VAC controller includes an interface jack for computer control, supported by the optional GS-232A Computer Controller, as well as many aftermarket control programs and interfaces. These azimuth and elevation rotators are actually two separate motor units, now DC controlled. They may be mounted together on a mast with the included mast bracket, or independently with the azimuth rotator inside a tower and the elevation rotator mounted on the mast above the top of the tower. They handle a total of about 10 sq. ft. of antenna wind load and rotate each way in about one minute. The Yaesu G-5500 AZ-EL clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-5550DC azimuth and elevation motors operate with two independent 22 V DC control lines, each a five-wire system, using the same connectors at the end of the control cable as the previous models. Both of the new DC motors, azimuth, and elevation, are marked "G-5550DC" at the connector. Be sure to mark your connectors AZ or EL. The rear panel of the controller is titled "G-5500DC" on the serial number label. WARNING: The legacy Yaesu G-5500 Rotator motors and controller used a 26 VAC control voltage, six-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-5500DC components, which only use pins 1, 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use five-conductor, 20 gauge control cable (5 x 20 AWG). If the rotator cable needs to be longer than 125 ft. then use five-conductor 18 gauge cable (5 x 18 AWG). The input voltage for the G-5500DC controller is labeled "117 VAC" to indicate house current range of 110 to 120 Vac. When you are launching your EME or satellite communications adventure, an azimuth/elevation combination rotator is a vital tool for your antenna system. As durable as they are attractive, Yaesu G-5500DC Azimuth-Elevation Rotator Systems are available from DX Engineering.
( 17 )
$969.99
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 20 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-800DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-800DXA Medium Heavy-Duty Rotator System from DX Engineering.
( 24 )
$659.99
Yaesu G-1000DXA Heavy-Duty Rotator Systems
Yaesu G-1000DXA Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-1000DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-1000DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 23 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-1000DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-1000DXA Heavy-Duty Rotator System from DX Engineering.
( 14 )
$799.99
DX Engineering RR8B-SD Remote Antenna Switches
DX Engineering RR8B-SD Remote Antenna Switches are the highest power handling antenna switches in the DX Engineering RR8 Series. Think of them as Super Duty. They are designed to switch up to 8 coaxial lines in high-power RF systems. RR8B-SD switches use enclosed RF-rated relays with exceptional RF voltage and current capability to provide reliable, long-term performance. DX Engineering RR8B-SD switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, allowing for use in complex antenna phasing and stacking systems. RR8B-SD switches use removable screw-terminal control cable plugs that greatly simplify installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting bracket flange, and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. outside diameter. RR8B-SD Remote Antenna Switches feature: * Fully shielded, high impact thermoplastic enclosure, stainless steel mounting bracket, and hardware * Excellent port isolation; greater than 60 dB at 30 MHz, worst case * Power Rating: Greater than 10 kW in normal amateur operation on all modes when using antennas with less than 2:1 SWR on 30 MHz and below. Greater than 5 kW above 30 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Lightning protection on control lines * Shorted or open selection of unused antenna ports * Custom sealed 30 ampere high-voltage RF relays * Solderless removable plug for easy installation of control line with no disassembly * Safe 12V DC relay operation * Reliable operation in all weather extremes Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For multi-band multi-antenna QRO operation, there is no better remote switch than DX Engineering RR8B-SD Remote Antenna Switches!
( 4 )
$599.99
DX Engineering RR8B-HP Remote Antenna Switches
DX Engineering RR8B-HP Remote Antenna Switches are RF switches designed to have excellent performance on HF through 6 meters. Using 16 custom, sealed, moisture-resistant relays, these Remote Switches provide the best port-to-port isolation available with reliable, long-term performance. RR8B-HP switches may be used as conventional one-of-eight antenna switches or configured to simultaneously select multiple output ports, thereby allowing their use in complex antenna phasing and stacking systems. DX Engineering RR8B-HP switches use a removable screw-terminal control cable plug that greatly simplifies installation by eliminating the need for disassembly or soldering to wire the control lines. These remote relay boxes are custom-made on a revised stainless steel chassis with integral mounting-bracket flange and include a special RF-shielded high-impact thermoplastic cover. There is also a custom conductive gasket to complete the seal between the cover and stainless steel housing base. A DX Engineering V-Bolt Saddle Clamp is included to mount the RR8B-HP on any tower leg or pipe sized from 1 to 2 in. O.D. Features of the RR8B-HP Remote Antenna Switches include: * Fully RF shielded with stainless steel mounting bracket and hardware * Best port-to-port isolation available: Over 70 dB isolation below 30 MHz, Over 55 dB isolation below 60 MHz * Loss: Less than 0.1 dB below 60 MHz * High-RF tolerant, Amphenol UHF female, SO-239 connectors * Shorted or open selection of unused antenna ports * Sealed 20 ampere, RF-rated relays * Safe 12V DC relay operation * Lightning protection on control lines * External quick-connect plug for control lines * Reliable operation in extreme-weather conditions Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For reliable operation of multiple antennas through the operation of remote switching, order DX Engineering RR8B-HP Remote Antenna Switches to do the job!
( 5 )
$549.99
Hustler Base Model G7-144 Vertical Antennas
Hustler Base Model G7-144 Vertical Antennas feature a 7 dBd maximum effective omni-directional gain; providing a consistent pattern, even in marginal areas. Extremely low-angle stacked 5/8 wave radiators deliver superior gain. Due to robust manufacture, harsh environments do not affect their mechanical or signal integrity. They are constructed from high-strength aluminum and employ a fiberglass radome for all-weather durability. Hustler G7-144 antennas are totally self-supporting and are easily assembled. When they are disassembled, their longest section is approximately 4 ft., which makes them easy to handle and move. They are great for EMCOMM and Field Day, or use one for your QTH or repeater service. When it comes to your signal, a good antenna is a must! Order Hustler Base Model G7-144 Vertical Antennas and give your signal a good boost!
( 12 )
$519.99
M2 Antennas 2M7 2 Meter Yagi Antennas
M2 Antennas 2M7 2 Meter Yagi Antennas are top quality, capable beams for the operator who wants the convenience of a short, 9 ft. boom, in an antenna that can handle full power and deliver true performance over the long term. The 2M7's are computer optimized Yagis that will outperform longer old design antennas. They cover the whole band with only slight performance degradation at the band edges. Their side lobes are very low and are perfect for stacking two or more for increased gain. Their light weight and durability make them great for portable hill topping and rover operations. M2 Antennas 2M7 are built for long term electrical and mechanical integrity. Their CNC machined "T" Match Block features O-ring sealed connectors and is internally sealed with a space-age silicone gel with nearly four times the dielectric strength of air. Full power operation is no problem for these antennas. Their elements are 6061-T6 3/16 in. aluminum rod, mounted through the boom on UV stabilized button insulators. All hardware is stainless steel except U-bolts. Other key electrical and mechanical parts are CNC machined for accuracy and durability. M2 Antennas 2M7 2 Meter Yagi Antennas can take your FM, SSB, CW or digital mode 2 meter operations to a new level. Get yours from DX Engineering!
( 12 )
$258.99
M2 Antennas 2M4X 2 Meter Yagi Antennas
M2 Antennas 2M4X 2 Meter Yagi Antennas are exceptional, with a clean mechanical design, full band coverage and computer optimized performance. A totally sealed and grounded driven element design with a unique internal balun provides the heart that will beat for years to come. The 2M4X is perfect for base or portable use. Its boom end-mount mast bracket allows either vertical polarization for FM or horizontal polarization for SSB, CW and Digital, plus easy stacking or tower side mounting. Every station needs at least one 2M4X! M2 Antennas designs and builds new antennas to fit the needs of Amateur Radio enthusiasts. The "X" series of antennas are redesigns that reduce packaging length to under 48 inches, to minimize oversize surcharges applied by shippers. The "X" series antennas offer the same performance as its predecessor, but with shorter and multiple boom sections. Some boom sections have a thicker wall for added strength. A side benefit of the "X" series antenna redesign is that they are now more portable with shorter boom sections. Replacing the popular 2M4, the 2M4X features a 50-ohm Type-N Female connector for the lowest loss. (If you prefer to use a 2 meter beam with an SO-239, see the M2 Antennas 2M3SS.)
( 5 )
$229.99
WiMo X-Quad Antennas
WiMo X-Quad Antennas, with separate monoband models for 144-146 MHz or 430-440 MHz, represent a refinement of VHF and UHF cross-polarized Yagis. They are well-known in Europe as "multi-element quads"—an antenna with aluminum elements, not a wire and fiberglass antenna—which offer excellent gain with a relatively short boom length. X-Quads are a great solution due to their short length and lightweight construction, especially for VHF/UHF satellite systems which require rotation in all compass directions and elevations. Two X-Quad Antennas, one for 144-146 MHz and one for 430-440 MHz, may be mounted at opposite ends of an azimuth-elevation rotator cross-boom for high-performance full duplex Satellite operations. For either or both bands, X-Quad Antennas may instead be used in a stationary mount, as pictured, for all-mode terrestrial operations. In either application, multiple X-Quad Antennas may be stacked vertically and horizontally for additional gain and tighter patterns. The WiMo X-Quad special features, developed specifically for Satellite Amateur Radio include: * Switchable Polarization Plane; horizontal/vertical/right hand circular/left hand circular (remote switching requires optional equipment) * High gain compared to other antenna forms due to the "stacking effect" * Short boom length and compact design * Back-end boom or mid-boom centered mounting to the mast is possible The radiator element is a "stacked quad" multi-element beam, for which linear polarization can be compared to a crossed slotted radiator. However, the advantage of the X-Quad is that it can be optimally used for the desired polarization by simply changing the feed. Compared to a typical cross-polarized Yagi, all directors and reflectors are active in the X-Quad, which enables the compact design. As with cross-polarized Yagis, switching is accomplished on the mono-band X-Quad either by a coaxial relay or with a band specific WiMo Remote Polarization Switch (sold separately). If the remote switch is mounted at the antenna, then only one coax cable and a 4-conductor control cable are required, sold separately. If the Switch is used at the station, then two coaxial cables from the antenna to the station are needed. The WiMo X-Quad Antenna can also be permanently set for circular operation by using an optional, band-specific Phase Line. The secondary elements are arranged diagonally in relation to the square-shaped driven element, which corresponds to the voltage distribution on the radiating element, for the most favorable results. In comparison to Yagi antennas, the X-Quad pattern and tuning are affected less by the influence of external fields, making them ideal for installation under a roof, in an attic space. All elements are electrically conductively connected with boom and cable outer sheath, thus eliminating interference from atmospheric noise. Two Type-N female coaxial connectors, one for each polarization, are mounted in a housing that is waterproof. Boom and elements are made of aluminum, all hardware is stainless steel. Construction and design of the antennas are protected by law (DBGM). The antennas are designed for boom-end mounting; however, alternatively the mast clamp can be mounted in the middle of a non-metallic boom. These antennas have a split boom, so their transport length is only 29.53 in. (75cm) for the 2m antenna and 25.59 in. (65cm) for the 70cm X-Quad. For portable operations they can be stowed away comfortably in the trunk of car and their shipping costs are comparatively low.
( 5 )
$349.99
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-2800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-2800DXA, G-1000DXA and G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 30 sq. ft. of antenna wind load and over 650 lbs. of vertical mast load. About 130 ft. of control cable is included with the G-2800DXA only. Control console power is 110/120 volts AC. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 50 to 120 seconds on the G-2800DXA, and preset a desired heading for the rotator, to which it then turns automatically. When a fast rotation speed is selected, special "auto slow-start" and "auto slow-stop" features avoid sharp jolts to the antenna array and tower. Activating the rotator causes it to begin turning at slow, but increasing, speed. As the antenna approaches the desired heading, the rotation automatically slows down, before bringing the antenna to a gentle stop. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-2800DXA Extra Heavy-Duty Rotator System from DX Engineering.
( 1 )
$1,769.99
M2 Antennas 2M9X 2 Meter Yagi Antennas
M2 Antennas 2M9X 2 Meter Yagi Antennas provide two sets of elements to build either a horizontally polarized SSB-CW-Digital beam or a vertically polarized FM beam, replacing the separate 2M9SSB and 2M9FM. Performance is optimized for a specific mode and frequency range, with no compromises to achieve unneeded bandwidth. The 2M9X SSB covers 144-146 MHz and the 2M9X FM covers 145-148 MHz. Where do you want to make yourself heard? Both models are ideal building blocks for a small turning radius, high-gain stacked array. Two horizontally polarized, vertically stacked 2M9Xs yield the same gain (14.8 dBd) as M2's 33 ft. 2M5WL, but with about 1/2 the turning radius. Great for QTHs that won't permit a long boom Yagi. The 2M9X can be stacked on a cross boom for the same gain increases, and the turning radius is still a very manageable 10 ft. Always designing and building new antennas to fit the needs of amateur radio operators, the "X" Series of antennas were redesigned to keep the packaging under 48 in. long, to minimize oversize surcharges applied by shippers. The "X" Series antennas offer the same performance as its predecessor, but with shorter boom sections. The boom sections also have a thicker wall for added strength. A side benefit of the "X" Series antennas are that they are more portable with the smaller sections. At the heart of M2 Antennas VHF beams is a driven element module originally designed for maritime ATS satellite service. All connectors are O-ring sealed to the CNC-machined block. Internal connections are sealed with a space-age silicone gel with nearly four times the dielectric strength of air. The balun connectors are triple sealed on the coax and nut-sealed at the block connectors. The type N feed connector uses a gold-plated, beryllium copper center pin. Elements are 6061-T6 3/16 in. solid rod with UV stabilized polyethylene Button insulators and stainless steel keepers. Thousands of these type elements are in amateur and commercial service with NO failures! Booms are constructed of 6061-T6 aluminum alloy tubing. Other key electrical and mechanical components are CNC machined for accuracy and durability. All hardware is stainless steel except the U-bolts. For uncompromising performance and long-term electrical and mechanical integrity, the 2M9X is unmatched. Specifications the M2 Antennas 2M9X: Frequency range (2M9X SSB): 144 To 146 MHz Frequency range (2M9X FM): 145 To 148 MHz Gain: 14.1 dBi Front to back: 20 dB Typical Beamwidth: E=35 degrees; H=38 degrees Feed type: "T" match Feed impedance: 50 Ohms unbalanced Maximum VSWR: 1.2:1 typical Input connector: N female Power handling: 1.5 kW Boom length/diameter: 14 ft. 6 in./1 to 3/4 in. OD Maximum element length: 40 5/8 in. Turning radius: 8 ft. Stacking distance: 9 ft. 6 in. High and 10 ft. Wide Mast Size: 1 1/2 to 2 in. Nom. Wind area/survival: 1.2 sq. ft./100 mph Weight/ship weight.: 5 lbs./7 lbs.
( 5 )
$403.99
DX Engineering RR8B Remote Antenna Switch and Control Console Packages
DX Engineering RR8B Remote Antenna Switch and Control Console Packages bring a new level of convenience to your antenna setup. These packages combine DX Engineering's 5 or 10 kW key-down switch, plus a CC-8A or EC-8 Control Console. RR8B series Remote Antenna Switches feature: * 0-54 MHz operation with industry leading port-to-port isolation * 5 or 10 kW versions * Fully RF shielded with high strength, UV-resistant cover, stainless steel mounting bracket, and hardware * Lightning protection is standard * Solderless, removable plug for easy installation of control line with no disassembly * Can be wired without disassembly * Can select individual or multiple ports for stacking and phased array applications * Safe 12V DC relay operation * Unused antenna ports are open by design; may be internally jumpered to be grounded when not selected CC-8A Consoles feature: * 1-of-8 control format * 8 front panel LEDs to indicate switch position (with adjustable brightness) * Rear panel external plug * Operates on your 12V DC source, ideal for battery or emergency ops * Ergonomic selector knob * Powder-coated metal housing EC-8 controller features include: * 1-of-8 control format * Green power LED * Operates on your 12V DC source, ideal for battery backup or EMCOMM * Ergonomic selector knob * Powder-coated metal housing Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When a complete remote antenna switching system is needed and high reliability is a must, DX Engineering RR8B Remote Antenna Switch and Control Console Packages are your best solution! * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
( 8 )
$739.98
—
$859.98