Availability
11 Results Found For "75 ohm coax"
DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable
DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable is our regular RG-6U with a Type II PVC jacket, low loss and greater protection against electromagnetic interference. Available cut to length or in 1,000 ft. spools; this is a high-quality standard RG-6U quad-shield cable. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. (Please Note: Also available is our waterproof direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ-CTL and DXE-RG6UFQ-1000.) DXE-RG-6UQ cable is ideal for many applications, such as active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution as well as satellite radio installations like Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up to the microwave frequencies that Satellite Radio systems employ! Our RG-6 quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding and the UV protected black jacket is made with a tough, but very flexible, PVC. The nominal impedance of DXE-RG-6UQ cable is 75 ohms, and it has a nominal Velocity Factor of 82%. The minimum bend radius of this cable is 2.50 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? Please Note: Also available is our direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ and DXE-RG6UFQ-1000. This DX Engineering RG-6UQ 75-ohm Standard Quad-Shield Coaxial Cable is a Type-II PVC jacket RG-6 quad-shield cable that is RoHS compliant. Check out these low attenuation figures: 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? Order DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable.
( 1 )
$219.99
DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coax Assemblies
Our patented* revolutionary new PL-259 connector and our premium, low-loss 400MAX coaxial cable are designed to make the new DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best cable assemblies available for simplex HF, VHF and UHF applications. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX DX Series low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 DX Series Coaxial Cable Assemblies are terminated at each end with our new, custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our new 400MAX DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are now available, only from DX Engineering! *U.S. Patent D745849
( 324 )
$144.99
DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Cable Assemblies
Our patented* revolutionary new PL-259 connector and our premium 213U coaxial cable were designed to make the new DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Assemblies the best 213/U cable assemblies available for virtually every HF antenna application. DX Engineering 213U is a high-grade standard coaxial cable type, which features a very rugged, highly UV-resistant, non-contaminating Type II-A PVC jacket. These cable assemblies are ideal for all outdoor feedline applications, commonly used for HF and direct-bury installations. With heavy 12.5 AWG stranded copper center conductor, RG-213U PL-259 cable assemblies are perfectly suited for long cable connections to antennas from HF equipment running at very low to high power levels. Our DXE-213U cable features a solid polyethylene dielectric that cannot absorb moisture and it withstands constant movement and flexing on tower mounted rotatable and directional beam antennas. DXE-213U is used at contest station K3LR for installation at the tower top as "rotator loop" coax for HF and VHF. It has excellent shielding with minimum 96 percent coverage copper braid. Regarded in the industry as the right choice for a high quality HF feedline, our 213U Coaxial Cable is custom made for DX Engineering to provide the performance and longevity you expect. DX Engineering RG-213U PL-259 DX Series Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 213U DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our Next Generation PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849
( 185 )
$149.99
DX Engineering 400MAX Type N Low-Loss 50-ohm Coax Assemblies
DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies offer the lowest possible loss at VHF and UHF frequencies. Used by communications professionals through 2,400 MHz and above, N-Type connectors have low insertion loss and maintain 50 Ohm impedance, for installations where every tenth of a dB counts! DX Engineering 400MAX coax features a tough, waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for simplex outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. B) Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. Our 400MAX DN Series cable assembly N-Type connectors feature machine crimped shields and centers, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate in-service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies are now available, only from DX Engineering!
( 33 )
$148.99
DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coax Cable Assemblies
Our patented* revolutionary new PL-259 connector and our high quality, low-loss RG-8U coaxial cable were designed to make the new, extra-flexible DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8/U cable assemblies available for all HF, VHF and UHF applications. DX Engineering 8U coax features a super-flexible jacket made with UV-resistant, Type I PVC jacket which is great for all indoor and above-ground outdoor applications. With a large 11 AWG stranded copper center conductor, our 8U DX Series low-loss assemblies are well suited for short interconnections as well as long cable runs in low or high power operations. Our 8U coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has excellent shielding with minimum 95 percent coverage copper braid. DX Engineering 8U is a new-age cable that far surpasses the capabilities of the moisture collecting foam RG-8/U of 35 years ago. Now regarded in the industry as a top quality low-loss feedline, our 8U Coaxial Cable is custom made for DX Engineering to provide the highest performance with extraordinary flexibility. DX Engineering RG-8U PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 8UDX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849
( 113 )
$132.99
DX Engineering RG-8X PL-259 Low-Loss 50-ohm RF Choke Coaxial Cable Assemblies
DX Engineering RG-8X PL-259 Low-Loss 50-ohm RF Choke Coaxial Cable Assemblies feature our patented* revolutionary PL-259 connector and our premium flexible DXE-8X coaxial cable. They were designed to make the best RG-8X cable assemblies available for HF applications. Adding fifteen Mix-31 ferrite beads makes them even better! The ferrite beads provide RF choking to reduce RFI and improve current balance on antennas. These assemblies are made with low-loss, gas injected foam dielectric DXE-8X cable, featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket. Okay for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, the gas-injected foam of DXE-8X cannot gather moisture and has lower loss than old RG-8X foam cables. The ferrite bead choke part of these cable assemblies should be connected to a grounded protector or the radio end of the cable, especially when used on End Fed Half-Wave or non-resonant antennas, random wires, and verticals. They are also used at feed point of a dipole or Yagi antenna. Many installations can benefit from the use of an RF Choke Coaxial Cable Assembly, such as isolating the coaxial cable from a remotely tuned antenna system for improved performance. DX Engineering RG-8X PL-259 Low-Loss RF Choke Coaxial Cable Assemblies are terminated with our custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. The patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849
Not Yet Reviewed
$115.99
DX Engineering RG-8X Hi-Viz Orange 50-ohm RF Choke Coaxial Cable Assemblies
DX Engineering RG-8X Hi-Viz Orange 50-ohm RF Choke Coaxial Cable Assemblies are the most flexible and lowest loss high-quality coaxial cable assemblies on the market. Assembled with fifteen Mix -31 ferrite beads under weather-sealed heat shrink, these DXE-8XV cables offer RF choking to reduce RFI and improve current balance on antennas. These flexible assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are terminated with high quality silver plated PTFE dielectric PL-259 (UHF male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. The end of these cable assemblies with the ferrite bead choke should be connected to a grounded protector or to the radio, especially when used on End Fed Half-Wave or non-resonant antennas and random wires, and some verticals. They are also used at feed point of a dipole or Yagi antenna. Many installations can benefit from the use of an RF Choke Coaxial Cable Assembly, such as isolating the coaxial cable from a remotely tuned antenna system for improved performance. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. Color of delivered cable can vary. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8XV is the part number for this coaxial cable sold by the foot, and it is available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.
( 3 )
$133.99
DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies
What if two RF devices – the radio, switch, meter, lightning protector, choke, balun or the antenna – have opposite female connectors, one type-N and the other SO-239? This dilemma is solved with the uniquely helpful DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies, the perfect alternative to questionable straight adapters. Made for any job (HF, VHF and UHF) and especially for outdoors, one top-quality silver plated Type-N male connector and one patented* Next Generation PL-259 (UHF male) connector terminates our premium, low-loss 400MAX coaxial cable to create these very useful Adapter Cable Assemblies. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications, including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX NX Series low-loss assemblies are perfectly suited for short or long cable runs and low or high-power level operations. Our 400MAX coaxial cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95-percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. Note: DXE-400MAX is not recommended for use in repeater applications, VHF/UHF duplex, or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 NX Series Coaxial Adapter Cable Assemblies are terminated at one end with the N-Type male connector and the other end with our custom-designed DX Engineering PL-259 (UHF male) connector. Both silver plated connectors feature machine-crimped shields with 360 degrees of complete mechanical and electrical contact for maximum reliability. PL-259 center pins are hand-soldered, and Type-N center pins are machine-crimped by trained assembly techs to assure a proper connection. Next Generation PL-259 connectors feature: * Full diameter, full-length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double-knurled threaded shells for secure finger tightening These high-quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies are available in selected lengths and at any length in the Custom Cable Builder, only from DX Engineering! *U.S. Patent D745849
( 8 )
$238.40
DX Engineering Phased Array Quarter Wave Tuned Cables
DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.
( 3 )
$137.13
—
$245.99
DX Engineering Pretuned Quarter-Wave Phased Array Cables
DX Engineering Pretuned Quarter-Wave Phased Array Cables are ready to go into your phased array for 80 or 40 meters. These RG-11U coaxial cable assemblies are electronically tuned during production to 3650 kHz and 7100 kHz, the two most popular phased array frequencies. Pretuned Quarter-Wave Phased Array Cables ensure optimum pattern control and gain from your phased antenna array. They are available individually, in pairs and in four-packs, all terminated with soldered silver-plated PL-259s. These cable assemblies are exactly as required for many 80 and 40 meters phased arrays including Comtek Hybrid Four Square Arrays, DX Engineering TFS4 Four Square Arrays, as well as DX Engineering Dual Vertical Arrays. DX Engineering Pretuned Quarter-Wave Phased Array Cables are made from the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable. They are called "phasing feed-lines" because they are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. This RG-11U coaxial cable is manufactured to DX Engineering specifications, with a nominal velocity factor of 0.82. That means they're the right physical length to allow for easy burial and routing from the center-mounted array phasing unit to the base of each vertical element. Maximum performance is achieve with properly installed phased arrays, including ground-mounted base-fed full-size quarter-wave elements with free-space array dimensions and complete, interconnected ground radial wire systems. The electrical dimensions of phased array transmission cables are critical to system performance. Each of our cable assemblies is hand crafted and electronically tuned at DX Engineering. Eliminate the trouble and concern of trying to tune your own cables and order a set of DX Engineering Pretuned Quarter-Wave Phased Array Cables. NOTE: Custom tuned phased cables for all other frequencies in each Amateur band are also available. See DX Engineering Phased Array Quarter Wave Tuned Cables.
( 1 )
$119.99
—
$239.98
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.
Not Yet Reviewed
$249.99