Availability
14 Results Found For "in-line"
Yaesu DC Power Cables
Yaesu DC Power Cables are as originally supplied for your Yaesu radio. Yaesu-matched power connectors and in-line fuses allow you to safely connect your radio to a DC power supply or run it mobile. An extra DC power cable makes it easy to move your radio from one power source to another… or home to car. Replacement Yaesu DC Power Cables are available now; here at DX Engineering!
( 76 )
$25.49
—
$47.99
Heil Sound Headset Adapter Cables
Heil Sound Headset Adapter Cables are used to interface your Heil headset to your favorite transceiver. Heil AD-1 series headset radio cables are required for Heil boom microphone headset models including PROSET Elite, PROSET, the original and reintroduced PRO-MICRO series, the lightweight, yellow BM-17 series and BM-10 series headsets, and the legacy PROSET PLUS. These cables support all of the Heil Sound Headsets that feature a 3.5 mm (1/8 in. miniature phone) mono connector for the microphone audio. Each has a female 1/4 in. mono dongle connector on a short wire for PTT keying foot switch or hand switch connection. NOTE: These Heil Headset Adapter Cable assemblies handle mic audio and keying, NOT the headphone audio. The stereo male plug on your headset cable connects directly to your transceiver headphone jack, not to the AD-1 series adapter cable. Headsets typically include stereo 1/8 in. (3.5mm) to 1/4 in. (6.35mm) headphone audio adapters. All Heil Headset Adapter Cables use commercial-grade microphone connectors with dual-exit cable clamps that are much heavier than the normal CB-type connectors that the industry had been forced to use for decades. If you have several brands of transceivers, individual adapter cables may be connected to each radio, so you may quickly and easily move your Heil boom microphone headset from one transceiver to another, without having to remove any connectors from the transceivers. All Heil audio cables are wired through to support VOX operation. Heil Sound Headset Adapter Cables are available in 4-pin and 8-pin round connectors, and 6-pin and 8-pin modular-style connectors. HSTA series Headset Adapter Cables were specially designed for the legacy Heil TRAVELER Headsets that were discontinued and are no longer available. Some of the presently available adapter cables feature an extra wire and connector to go to the transceiver external speaker connector, for those radios where receive audio is not provided on the microphone connector. On transceivers that support them, the special UP-DOWN buttons on the TRAVELER Headset cables are connected with these cables.
( 214 )
$30.00
Heil Sound Microphone Adapter Cables
Superior-quality Heil Sound Microphone Adapter Cables, CC-1 series, are used to connect your Heil microphone to your favorite transceiver. There are two types of cables available for the two types of Heil microphones, 4-pin XLR and 3-pin XLR. Both adapter cable types feature the PTT mono 1/4 inch (6.35mm) jack at the transceiver mic connector for a foot switch or hand switch. Heil Sound Microphone Adapter Cables are available with round 8-pin, round 4-pin and 8-pin modular-style connectors for most transceivers. Most Heil Microphone adapter cables feature the special 4-pin XLR connector to serve the Heil microphones that have a built-in PTT switch. They work with the Classic, Goldline, GM, HM-12 Genesis, Handi-Mic, HM-10XD and HM-10 microphones. Use of an external foot or hand switch is optional. Conversely, the cables with the letters "XLR" in the part number have the audio industry standard 3-pin XLR microphone connector. These cables are required for the "PR" PRO Series microphones such as the PR-20, PR-28, PR-40, PR-781 and several others. Since these mics have no PTT switch, they require the use of an outboard hand or foot switch connected to the adapter cable PTT jack. Features and benefits of Heil Microphone Adapter Cables compared to others: * 100 percent silver-braid shield... keeps noise OUT * PTT control lines are OUTSIDE the shield... eliminates stray coupling * Made using commercial-audio grade 'Heilwire'... strong and supple * 18-gauge wire; not 22 or 24 like others... lower cable resistance * Commercial-grade microphone connectors (patent pending)... lasting durability * Heil dual-exit cable clamps are heavier than normal connectors... robust reliability * Outstanding engineering... lowest-noise transmit audio The XLR connector's quick-disconnect feature lets you easily move your Heil microphone from transceiver cable to transceiver cable, at the microphone end, without having to rewire a boom or remove any connectors from the transceivers. Additionally, all Heil audio cables are wired through to support VOX operation. Don't attach a high-quality microphone to cheap cable! Order your Heil Sound Microphone Adapter Cables from DX Engineering and transmit the best audio possible!
( 149 )
$30.00
—
$49.00
ICOM DC Power Cables
Keep your radios running properly with ICOM DC power cables. Available with connectors for your ICOM DC powered transceiver and inline fuses to protect your transceiver, ICOM DC power cables keep you on the air.
( 22 )
$28.99
—
$45.99
12 Volt Power, Inc. DC Power Cable Assemblies
12 Volt Power, Inc. offers a range of premium DC power cable assemblies designed to supply power to HF transceivers, FM transceivers, and various electronic devices from multiple power sources and connector types. Look no further than DX Engineering for your 12 Volt Power, Inc. DC Power Cable Assemblies.
( 7 )
$25.99
—
$34.99
Digirig USB Isolators
Digirig USB Isolators are a compact and effective solution for effectively removing ground loop-induced hum and interference by isolating your PC from transceivers and audio devices. They also serve as a protective barrier for your computer when using USB-connected test equipment such as JTAG debuggers, oscilloscopes, and programmers. Built with high-quality components, the Digirig USB Isolator features signal isolation up to 2.5kV and power isolation up to 1.6kV, utilizing the ADUM3160 for signal and B0505S for power. It supports USB 2.0 Full and Low Speed devices, with a load capacity of up to 1W, though it is not recommended for charging devices that draw more than 180mA.
( 1 )
$22.95
DX Engineering Transceiver Amplifier Keying Cables
DX Engineering Transceiver Amplifier Keying Cables connect the "ground on transmit" or contact closure provided by the radio that is required to make an HF amplifier switch from "receive mode" to "transmit and amplify mode" when using PTT (push-to-talk), VOX or break-in CW keying. DX Engineering Transceiver Amplifier Keying Cables are made for specific transceiver models that have special DIN or mini-DIN connector accessory ports which provide the transceiver's only connections for linear amplifier keying. One type of amplifier keying cable has one RCA phono plug for the amplifier relay jack, which is all that is needed. When the transceiver PTT (push-to-talk) is keyed, the RCA plug center pin is connected to the shield (and chassis ground in most cases) to key the amp relay or its solid state keying circuit. Instead of a direct connection to the amp relay, the RCA plug may be connected to the keying input of an accessory device (DXE-KEYLINE-3, DXE-RTR-2 or DXE-NCC-2), amplifier keying interface (DXE-SV-KR or legacy Ameritron ARB-704 or KD9SV Products SV-KR) or other amp keying line interrupt device, such as a meter or an array controller. Each has a keying input and a keying output for the amplifier relay or another accessory. Another type of amplifier keying cable has two RCA phono plugs, one RED plug for the amplifier relay jack and one WHITE plug for ALC (Automatic Level Control) voltage from the amplifier. The legacy ALC connection does not need to be used with present era solid state transceivers and most modern amplifiers. ALC was required for use on transmitters with tube finals. Some modern amplifiers do not have an ALC output connector. If the amplifier does not have ALC it is okay to leave the WHITE plug disconnected. Order your DX Engineering Transceiver Amplifier Keying Cables to connect to your transceiver accessory port for keying amplifiers, sequencers, receive-transmit interfaces, buffer relays, and other accessories. NOTE: To enable the function of this keying cable, some late model Kenwood transceivers require menu activation of the amplifier keying circuit.
( 51 )
$36.99
—
$41.99
Amphenol RF UHF Male Crimp Connectors
Amphenol RF UHF Male Crimp Connectors are lightweight units that are designed to operate up to 300 MHz. The PL-259 UHF Male connector has become the de facto standard for HF and VHF transmission lines. These connectors feature brass bodies finished in bright-nickel plating. Their Phenolic dielectric material resists water absorption, while their gold or silver-plated contacts ensure low-resistance connective surfaces. The PL-259 was the original US military designation for these "UHF" connectors, named for the upper frequency limit of their use at the time. Therefore, UHF Male for PL-259 and UHF Female for SO-239 are the terms recognized around the world. When shopping for UHF connectors, be sure to consider these Amphenol RF UHF Male Crimp Connectors now available from DX Engineering!
( 30 )
$23.99
—
$44.99
Kenwood DC Power Cables
Kenwood DC Power Cables were made specifically for your Kenwood radio. Perfectly matched connectors and in-line fuses let you safely connect your radio to a DC power supply or a run it in a mobile. Get an extra DC power cable to make it easy to move your radio from one power source to another. Replacement Kenwood DC Power Cables are here at DX Engineering!
( 12 )
$30.99
Amphenol RF 031-28 UHF to BNC Coaxial Adapters
Amphenol RF 031-28 UHF/BNC Coaxial Adapters are used convert a UHF SO-239 jack for use as a BNC female jack. These adapters deliver positive, secure female connection for your BNC-Male terminated jumpers or feed line. Their nickel-plated brass bodies have high-quality silver-plated center contacts to ensure the best performance in any application. Amphenol RF 031-28 details: * Description: Adapter, jack to jack * Body Material: Brass * Body Plating: Nickel * Body Style: Straight * Contact Plating: Silver * Dielectric: Co-polymer of Styrene * Gender: UHF Male, PL-259/BNC Female * Impedance: 50 Ohms * RoHS compliant Choose the coaxial adapters you need from DX Engineering's wide selection of quality coax adapters and connectors. When you need UHF to BNC female adapters, Amphenol RF 031-28 UHF/BNC Coaxial Adapters will provide the BNC RF or test connection you need. Order yours from DX Engineering… today!
( 2 )
$38.99
Extension Cables for Yaesu Rotator Controllers
Extension Cables for Yaesu Rotator Controllers provide an easy-to-reach quick-disconnect in the station for user made or for premade DX Engineering Yaesu Rotator Cable Assemblies (DXE-YRC series). Available in several lengths, purchase the extension cable length you need to make it easy to disconnect the rotator control line from your Yaesu controller. These cables allow the controller to be repositioned and moved more easily. Plus, disconnecting the rotator control line when leaving the shack offers additional protection for the controller. Each 6-conductor 18 AWG extension cable has the standard Yaesu female 6-pin Molex installed on one end and the male 6-pin Molex installed on the other end, for use between the long Yaesu rotator control cable run and the rotator controller. Heat shrink on the cable ends provide strain relief and longevity.
Not Yet Reviewed
$47.99
Heil Sound Heil Wire Microphone Cable
Heil Sound Heilwire Microphone Cable is a specially-designed cable ideal for connecting microphones, foot switches, keyer paddles, and other audio, data or control devices. Heilwire features two 18-gauge wires inside a 100% coverage silver-plated braid shield, plus two 18-gauge wires external to the braid, for PTT or other control purposes. This design reduces capacitive coupling between the control lines and the sensitive AC audio signals residing inside the shield, resulting in significant reduction of the possibility of hum pickup, PTT pulses or RFI. Heilwire has an outer jacket made with extra flexible PVC and has a specified outer diameter of 1/4 in. to fit perfectly inside Heil Sound connectors. Heilwire Microphone Cable is great for many different types of audio and switching connectors and applications. For making connections to microphones and other devices, Heil Sound's exclusive Heilwire is the best choice. Get some today from DX Engineering.
( 7 )
$30.00
Alinco DC Power Cables
Keep your radios running with Alinco DC Power Cables, with the connectors and plugs specifically designed for your Alinco DC powered transceiver. Some have inline fuses to protect your transceiver, the original equipment replacement and accessory DC Power Cables from Alinco will keep you on the air, wherever you go!
( 5 )
$24.99
—
$34.99
Digirig DC Power Cables
Digirig DC Power Cables provide dependable, high-quality power connections for transceivers. These cable assemblies support a variety of power sources and connector types, making them ideal for any Amateur Radio GoBox, shack, or portable operation. For proven performance and compatibility, choose Digirig DC Power Cable Assemblies, available at DX Engineering.
Not Yet Reviewed
$22.95
—
$28.45