Availability
Cable and Connectors
DX Commander DX10 Antenna Wire Spools
DX Commander DX10 Antenna Wire Spools provides enough wire to replace the elements on DX Commander antenna models while still having enough wire left over to make several radials. Made in England for DX Commander, DX10 wire has an outstanding reputation for both strength and in particular, extreme flexibility. The insulation is "arctic grade" and still flexible down to -40° F. Originally designed for military use, this insulation is particularly strong but highly flexible and the stranded annealed copper wire is approximately equivalent to 19 AWG and is made from 24 strands of 0.008 in. (0.2mm) wire.
( 17 )
$95.99
DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coax Cable Assemblies
Our patented* revolutionary new PL-259 connector and our premium flexible DXE-8X coaxial cable were designed to make the new DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8X cable assemblies available for HF applications. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are made from our new-process low-loss, gas injected foam dielectric cable. Featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket, good for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, this is the new type of foam that cannot gather moisture and has lower loss than old RG-8X foam cables. DX Engineering RG-8X PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These new, ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849
( 543 )
$52.99
—
$91.99
DX Engineering Next Generation Crimp/Solder 8U PL-259 Connectors
DX Engineering proudly announces our new, ultra-high quality, PL-259 connector that is so different from previous designs that we have a Patent**! DX Engineering Next Generation Crimp/Solder 8U UHF Male Connectors are now available to build your custom coaxial cable assemblies. Engineering studies have confirmed that the absolute best RF connections for double-shielded cables like LMR-400 and DXE-400MAX are made by crimping the shield, not soldering. However, most PL-259 crimped center pins aren't large enough and don't have enough contact area, which affects reliability. DX Engineering has solved those issues with these custom-designed connectors that we introduced on DX Engineering DX Series Coaxial Cable Assemblies. These PL-259s have soldered center pins that are full length and full diameter, so they connect properly, even with worn SO-239s. DX Engineering Next Generation PL-259CS8U series connectors achieve exceptional RF performance and power handling with these features: * All silver-plated brass shell and body * Silver-plated center pin securely mounted in PTFE dielectric * Center pin accepts large conductors and scalloped-tip allows generous solder flow * Crimped shield connection provides maximum reliability for all cables * Deep, double-knurled threaded shells for secure finger tightening * Fits all RG-8U size cables with center conductors up to 10 AWG including DXE-400MAX and LMR-400 as well as RG-213U, RG-11U and many others, including Belden 7810A, 8214, 8267 and 8237, 9913 and 9913F7. * Available in packages of 6, 12 or 24 connectors NOTE: DX Engineering offers reasonably priced, professional grade cable prep and connector crimping tools for an entire range of cables and connectors. Click "More Details" and the "Suggested Parts" tab to see available related products. Now you don't have to use the same old PL-259s. These advanced-technology PL-259 connectors let you build the highest quality coaxial cable assemblies. We designed them to be strong and lightweight and they represent a landmark improvement over decades-old, unchanged connector designs. This time, new IS better! Order DX Engineering Next Generation Crimp/Solder 8U UHF Male Connectors today and take advantage of DX Engineering innovations in RF connectivity! **U.S. Patent D745849
( 230 )
$59.99
DX Engineering Next Generation Crimp/Solder 8X PL-259 Connectors
DX Engineering proudly announces our new, ultra-high quality, PL-259 connector that is so different from previous designs that we have a Patent**! DX Engineering Next Generation Crimp/Solder 8X UHF Male Connectors are now available to build your custom coaxial cable assemblies. Engineering studies have confirmed that the absolute best RF connections for double-shielded cables are made by crimping the shield, not soldering. However, most PL-259 crimped center pins aren't long enough and some don't even have enough crimped contact area, which affects reliability. DX Engineering has solved those issues with these custom-designed connectors that we introduced on new DX Engineering 8XDX Series Coaxial Cable Assemblies. These PL-259s have soldered center pins that are full length and full diameter, so they connect properly, even with worn SO-239s. DX Engineering Next Generation PL-259CS8X series connectors achieve exceptional RF performance with these features: * Fits all standard RG-8X size cables including DXE-8X, LMR-240 as well as RG-59, RG-62 and many others, including Belden 9258, 8241, 1505 and 7808 series * All silver-plated brass shell and body * Silver-plated center pin securely mounted in PTFE dielectric * Center pin scalloped-tip allows generous solder flow * Crimped shield connection provides maximum reliability for all cables * Deep, double-knurled threaded shells for secure finger tightening * Available in packages of 6, 12 or 24 connectors NOTE: DX Engineering offers reasonably priced, professional grade cable prep and connector crimping tools for an entire range of cables and connectors. Click "More Details" and the "Suggested Parts" tab to see available related products. Now you don't have to use the same old PL-259s. These advanced-technology PL-259 connectors let you build the highest quality coaxial cable assemblies. We designed them to be strong and lightweight and they represent a landmark improvement over decades-old, unchanged connector designs. This time, new IS better! Order DX Engineering Next Generation Crimp/Solder 8X UHF Male Connectors today and take advantage of DX Engineering innovations in RF connectivity! **U.S. Patent D745849
( 157 )
$58.99
DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies
DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are the most flexible and lowest loss high-quality orange coaxial cable assemblies on the market. DXE-8XV cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are terminated with high quality silver plated PTFE dielectric PL-259s, and select lengths with BNC connectors for POTA and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. Color delivered can vary. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8XV is the part number for this coaxial cable sold by the foot, and it is available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.
( 22 )
$55.51
—
$99.99
Comet Window Feed-Thru Jumpers
Comet Window Feed-Thru Jumpers are flexible, 50 ohm, flat feedline assemblies with SO-239 UHF female connectors at each end. They are used for routing RF through a window frame without drilling holes for the coax cable or connectors. These window-gap jumpers are almost 16 in. long and are made from copper-clad steel and PET plastic to allow for a low power transfer of RF with a nominal loss of only 0.5 dB up to 500 MHz, and they are useable up to 1300 MHz! When drilling through the wall is forbidden, or if there is no way to make a sufficient hole for your coaxial cable, then a Comet Window Feed-Thru Jumper may be the problem solver that you need! Here are the specs that will help you decide if one of these handy flat cable assemblies is right for you: * Frequency Range: DC-1300 MHz * Connectors: SO-239 * Impedance: 50 Ohm * Length: 15.75 inches * Max Power: HF 100W PEP, VHF: 60W FM, UHF 40W FM, 900 MHz–1.3 * GHz: 10W FM * SWR: Less than 1.3:1 below 500 MHz, Less than 1.5:1 above 500 MHz * Loss: DC-500 MHz = 0.5 dB, 500-900 MHz = 1.3 dB, 900-1300 MHz = 1.8 dB Whether you use one of these feed thru devices for a temporary coaxial installation or as a permanent no-hole solution, Comet Window Feed-Thru Jumpers from DX Engineering can get you on the air!
( 34 )
$64.95
DX Engineering Premium Antenna Wire
DX Engineering Premium Antenna Wire helps you achieve top performance and long, trouble-free operation at a very reasonable cost. This PVC-insulated 14 AWG stranded copper wire is comprised of 19 strands of 27 AWG solid copper. Its relaxed PVC insulation is UV-resistant and rolls out easily, unlike wire that is commonly available at "big-box" stores, which coils and kinks. Our antenna wire is well worth its price for its features, especially for ease in handling. Over a decade of successful wire antenna installations have proven this insulated copper wire is up to the task. Conservatively rated at 92.5 lbs. breaking strength, this wire is strong enough for virtually every wire antenna application. Suggested installation includes supporting the feedpoint to properly handle the weight of the feedline, and balun if used, so that the wires only need to support themselves. When placed under extreme stress, this copper wire will stretch before breaking, allowing it to serve in a longer lasting installation for wire antennas of almost any style. Available in several pre-cut coiled lengths as well as on 500 and 1,000 ft. rolls, UV-resistant black insulated 14 AWG stranded copper DX Engineering Antenna Wire lasts longer than bare wire exposed to the elements. Use it with confidence for your wire antenna projects and get on the air!
( 144 )
$94.99
Amphenol RF 83-1SP-6 PL-259 Coaxial Connectors
Amphenol RF 83-1SP-6 PL-259 Coaxial Connectors are quality RF products that provide a positive, secure connection for your coax cable. This part number is for a half-dozen connectors. These superior Amphenol RF brand PL-259 connectors have a nickel-plated shell and silver-plated body and pin that make soldering and assembly a snap. They have close manufacturing tolerances you can FEEL! Tough Liquid Crystal Polymer (LCP) dielectric insulation further ensures the best performance for your application. These superior PL-259 connectors are the genuine Amphenol RF coaxial connectors you have been asking for from our selection of DX Engineering connectors. Amphenol RF 83-1SP-6 PL-259s use the standard reducers (sold separately) for DXE-8X and RG-58 cables. You asked and we listened! Order your Amphenol RF 83-1SP PL-259 Coaxial Connectors from DX Engineering and enjoy genuine Amphenol quality!
( 54 )
$68.99
DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coax Assemblies
Our patented* revolutionary new PL-259 connector and our premium, low-loss 400MAX coaxial cable are designed to make the new DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best cable assemblies available for simplex HF, VHF and UHF applications. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX DX Series low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 DX Series Coaxial Cable Assemblies are terminated at each end with our new, custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our new 400MAX DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are now available, only from DX Engineering! *U.S. Patent D745849
( 322 )
$52.99
—
$70.99
Amphenol RF 83-1AP UHF Right Angle Coaxial Adapters
Amphenol RF 83-1AP UHF Right Angle Adapters are used convert a UHF SO-239 jack to a 90 degree angle for easy coax connection to a female jack. These adapters allow equipment to sit closer to walls and cabinet dividers because coax may be connected parallel to the rear of the equipment chassis. These adapters deliver positive, secure female connection for your UHF-Male terminated jumpers or feed line. Their nickel-plated Zamac bodies have high-quality nickel-plated brass center contacts to ensure good performance. Amphenol RF 83-1AP details: * Description: Adapter, jack to jack * Body Material: Zamac * Body Plating: Nickel * Body Style: Right Angle * Contact Material: Brass * Contact Plating: Nickel * Dielectric: PTFE * Gender: UHF Male, UHF Female * Impedance: 50 Ohms Choose the coaxial adapters you need from DX Engineering's wide selection of quality coax adapters and connectors. When you need UHF right-angle adapters, Amphenol RF 83-1AP UHF Right Angle Adapters will provide the connection you need. Order yours from DX Engineering… today!
( 32 )
$58.99
DX Engineering LMR400UF Ultra-Flex Coaxial Cable Assemblies
DX Engineering LMR400UF UltraFlex Coaxial Cable Assemblies handle twice the power at half the loss with the same bending capabilities of smaller diameter coaxial cables. UltraFlex Cable Assemblies are perfect for interconnecting high and low power HF and VHF equipment. Times Microwave LMR® 400UF UltraFlex cable has a stranded bare copper center, foam polyethylene dielectric and a pliable rubber jacket (black thermoplastic elastomer) designed for bending. DX Engineering LMR400UF UltraFlex DX Series PL-259 Coaxial Cable Assemblies are terminated at each end with our custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity checked and evaluated with extremely high voltage, then heat-shrink weather-sealed for ultimate longevity. You will not find this level of cable assembly quality anywhere else! Terminated with DX Engineering Next Generation PL-259 connectors, these cable assemblies are intended for use to 170 MHz. An exceptionally flexible, low-loss coaxial jumper for high power Amateur or commercial HF or VHF use – order DX Engineering LMR400UF UltraFlex Coaxial Cable Assemblies.
( 30 )
$54.19
—
$72.59
DX Engineering Stealth Antenna Wire
DX Engineering Stealth Antenna Wire is very thin, at 26 AWG, and is very hard to see, jacketed in rugged black UV resistant polyethylene. For its size this is a surprisingly strong wire with a break load of over 24 pound-force and with a length of 62 feet weighing in at only 1 oz., it is also incredibly light! This "kite" wire is ideal for antennas intended for back-packing, camping and stealth portable operations. This is the wire to buy to build a center-supported HF stealth dipoles, inverted-vees or modest length end-fed wire antennas, just right for challenging CC&R and HOA installations. Under a 2:1 SWR this wire easily handles 100 watts SSB PEP, 50 watts CW and 25 watts Digital. DXE Stealth Antenna Wire Specs: Conductor: 26 AWG Copper-coated Steel (0.019 in., 7 strands) Conductor Break Load: 24.5 lbf Insulation: High Density Polyethylene (PE) Insulation Color: Black, UV resistant Insulation Thickness, nominal: 0.011 in. Overall Diameter, nominal: 0.041 in. Overall Weight: 0.016 oz. /ft. (0.62 lbs. /500 ft.) Spool Lengths: 150 ft., 250ft. and 500 ft. For HF operations with nearly invisible wire antenna, on the sly or on the go, choose DX Engineering Stealth Antenna Wire.
( 39 )
$72.99
DX Engineering Transceiver Amplifier Keying Cables
DX Engineering Transceiver Amplifier Keying Cables connect the "ground on transmit" or contact closure provided by the radio that is required to make an HF amplifier switch from "receive mode" to "transmit and amplify mode" when using PTT (push-to-talk), VOX or break-in CW keying. DX Engineering Transceiver Amplifier Keying Cables are made for specific transceiver models that have special DIN or mini-DIN connector accessory ports which provide the transceiver's only connections for linear amplifier keying. One type of amplifier keying cable has one RCA phono plug for the amplifier relay jack, which is all that is needed. When the transceiver PTT (push-to-talk) is keyed, the RCA plug center pin is connected to the shield (and chassis ground in most cases) to key the amp relay or its solid state keying circuit. Instead of a direct connection to the amp relay, the RCA plug may be connected to the keying input of an accessory device (DXE-KEYLINE-3, DXE-RTR-2 or DXE-NCC-2), amplifier keying interface (DXE-SV-KR or legacy Ameritron ARB-704 or KD9SV Products SV-KR) or other amp keying line interrupt device, such as a meter or an array controller. Each has a keying input and a keying output for the amplifier relay or another accessory. Another type of amplifier keying cable has two RCA phono plugs, one RED plug for the amplifier relay jack and one WHITE plug for ALC (Automatic Level Control) voltage from the amplifier. The legacy ALC connection does not need to be used with present era solid state transceivers and most modern amplifiers. ALC was required for use on transmitters with tube finals. Some modern amplifiers do not have an ALC output connector. If the amplifier does not have ALC it is okay to leave the WHITE plug disconnected. Order your DX Engineering Transceiver Amplifier Keying Cables to connect to your transceiver accessory port for keying amplifiers, sequencers, receive-transmit interfaces, buffer relays, and other accessories. NOTE: To enable the function of this keying cable, some late model Kenwood transceivers require menu activation of the amplifier keying circuit.
( 51 )
$51.99
—
$59.99
Summit Racing™ Accessory Wire
Summit® Accessory Wire isn't the run-of-the-mill wire that is found in a local hardware store. This is high-quality stranded-copper wire with excellent insulation that resists grease, oil, and acids. Use it for all types of projects to suit your needs. This top-notch wire is available in a variety of AWG sizes and lengths with several insulation colors for a professional wiring. Order a few rolls now to have on hand and be ready for your next electronics or electrical project!
( 2 )
$51.99
Yaesu Separation Cables
Yaesu Separation Cables are for connection of control faceplates to separately mounted mobile transceiver units.
( 22 )
$59.99
—
$84.99
Yaesu Interface Cables
Yaesu Interface Cables include data, cloning and "CAT" computer interface connections. Developed or selected by Yaesu engineers for specific transceiver models and specific functions, these are original Yaesu cables. Get your Yaesu radio completely connected with Yaesu Interface Cables from DX Engineering! IMPORTANT Note for Yaesu Radio models: FT-450, FT-450D, FT-950, FTDX-10, FTDX-1200 * When using the IC-109 cable to 10-pin mini-DIN, the LINEAR Port must be used on these transceiver models. * DO NOT use the 8-pin TUNER port. * DO NOT set EXT in the Tuner Select menu
( 106 )
$54.99
—
$69.99
DX Engineering 400MAX Type N Low-Loss 50-ohm Coax Assemblies
DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies offer the lowest possible loss at VHF and UHF frequencies. Used by communications professionals through 2,400 MHz and above, N-Type connectors have low insertion loss and maintain 50 Ohm impedance, for installations where every tenth of a dB counts! DX Engineering 400MAX coax features a tough, waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for simplex outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. B) Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. Our 400MAX DN Series cable assembly N-Type connectors feature machine crimped shields and centers, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate in-service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies are now available, only from DX Engineering!
( 33 )
$53.99
—
$71.99
DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coax Cable Assemblies
Our patented* revolutionary new PL-259 connector and our high quality, low-loss RG-8U coaxial cable were designed to make the new, extra-flexible DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8/U cable assemblies available for all HF, VHF and UHF applications. DX Engineering 8U coax features a super-flexible jacket made with UV-resistant, Type I PVC jacket which is great for all indoor and above-ground outdoor applications. With a large 11 AWG stranded copper center conductor, our 8U DX Series low-loss assemblies are well suited for short interconnections as well as long cable runs in low or high power operations. Our 8U coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has excellent shielding with minimum 95 percent coverage copper braid. DX Engineering 8U is a new-age cable that far surpasses the capabilities of the moisture collecting foam RG-8/U of 35 years ago. Now regarded in the industry as a top quality low-loss feedline, our 8U Coaxial Cable is custom made for DX Engineering to provide the highest performance with extraordinary flexibility. DX Engineering RG-8U PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 8UDX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849
( 113 )
$51.99
—
$99.99
DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Cable Assemblies
Our patented* revolutionary new PL-259 connector and our premium 213U coaxial cable were designed to make the new DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Assemblies the best 213/U cable assemblies available for virtually every HF antenna application. DX Engineering 213U is a high-grade standard coaxial cable type, which features a very rugged, highly UV-resistant, non-contaminating Type II-A PVC jacket. These cable assemblies are ideal for all outdoor feedline applications, commonly used for HF and direct-bury installations. With heavy 12.5 AWG stranded copper center conductor, RG-213U PL-259 cable assemblies are perfectly suited for long cable connections to antennas from HF equipment running at very low to high power levels. Our DXE-213U cable features a solid polyethylene dielectric that cannot absorb moisture and it withstands constant movement and flexing on tower mounted rotatable and directional beam antennas. DXE-213U is used at contest station K3LR for installation at the tower top as "rotator loop" coax for HF and VHF. It has excellent shielding with minimum 96 percent coverage copper braid. Regarded in the industry as the right choice for a high quality HF feedline, our 213U Coaxial Cable is custom made for DX Engineering to provide the performance and longevity you expect. DX Engineering RG-213U PL-259 DX Series Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 213U DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our Next Generation PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849
( 184 )
$55.99
—
$72.99
Armoloq RF Cable Relocation Kits
Armoloq RF Cable Relocation Kits are the ideal complement to the Armoloq Tactical Protective Armor (TPA) Modular Radio Mounting Frames. They simplify the process of relocating the RF connection to a more accessible and convenient position when the radio is secured within the TPA frame.
Not Yet Reviewed
$99.99
Pigtail Cables for Yaesu Azimuth-Elevation Rotator Controllers
Pigtail Cables for Yaesu Azimuth-Elevation Rotator Controllers offer a handy way to be able to use the quick-disconnect premade DX Engineering Yaesu Rotator Cable Assemblies (DXE-YRC series). Each 3 ft. pigtail has a female 6-pin connector on one end and #6 Ring Terminals installed on each color coded conductor at the other end, for permanent attachment to the screw terminals on the Yaesu Azimuth-Elevation Rotator Controller. Heat shrink on the cables and conductors provides strain relief and longevity. These pigtails make it much easier to move the controller into a different position, or for testing and for disconnection as a protection method. Purchase two pigtails per controller, one for the Azimuth rotator unit and one for the Elevation rotator unit. NOTE: Yaesu uses only five (5) conductors on each of the azimuth and elevation control cables. One pin of the 6-pin connector is open intentionally.
( 1 )
$53.99
Summit Racing™ SXL Primary Electrical Wire
Summit® SXL Primary Electrical Wire is an excellent choice for electronics and low voltage electrical projects, especially where high heat is present. Insulated with cross-linked polyethylene thermoplastic, this stranded copper wire is designed for use in engine compartments. Rated for use in circuits of 50 V or less, this wire has a temperature rating of 257 degrees F and resists the abrasion, oil, and gas found in high-heat applications. Summit® SXL Primary Electrical Wire meets USA vehicular SAE J1128 specifications, so it's the perfect choice for automotive electrical system projects. This top-notch wire is available in a variety of AWG sizes and with several insulation colors for a professional wiring job. Order a few rolls now to have on hand and be ready for your next electronics or electrical project!
Not Yet Reviewed
$51.99
—
$99.99
Diamond Antenna Through Window/Door Cable Sets
Diamond Antenna Through Window/Door Cable Sets are great for use when a hole cannot be drilled through the wall for a coaxial feedline. Made from a flat, flexible strip that acts like coaxial cable, these RF feedline assemblies have an SO-239 at each end, so connections to a radio indoors and an antenna outdoors is a snap! Now available from DX Engineering, here are the specs on Diamond Antenna Through Window/Door Cable Sets: Frequency range: DC to 1500MHz Max Power Ratings: * HF to 50MHz: 150 W (SSB), 50 W (FM/CW), * 144MHz: 40 W (FM) * 440MHz: 30 W (FM), * 1200 MHz: 10 W (FM) Length: 19.7 in. (between connectors) Weight: 102g; 6.0 oz. Connectors: UHF Female to UHF Female VSWR: * HF up to 500MHz: Less than 1.2 * 500 to 1000MHz : Less than 1.3 * Up to 1000MHz: Less than 2.0 * 1200MHz: Less than 1.7. Impedance: 50 ohms Insertion Loss: * 144MHz: Less than 0.3dB * 440MHz: Less than 0.6dB * 1200MHz: Less than 1.6dB Here's an easy solution to get your signal through the window! Order Diamond Antenna Through Window/Door Cable Sets from DX Engineering!
( 19 )
$56.99
DX Engineering RG-8X BNC Low-Loss 50-ohm Coax Cable Assemblies
DX Engineering RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies are very flexible low-loss, foam-dielectric, braided shield cable intended for special connections to BNC equipment. Suitable for moderate-power, base, mobile or portable applications where short runs and flexibility are key factors. NOTE: THESE ARE NOT PL-259 CABLES. These assemblies have BNC MALE connectors installed at each end of the cable, for use on specialized equipment with BNC Female connectors. Slightly larger than RG-58 cable, DX Engineering DX Engineering RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies are made from our new-process low-loss, gas injected foam dielectric cable. Featuring stranded copper center, braided copper shield and a non-contaminating Type II PVC jacket, our 8X BNC cable assemblies are intended for low to moderate power, test and mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, this is the new type of foam that cannot gather moisture and has lower loss than old RG-8X foam cables. Our RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies come complete with high-quality nickel-body Delrin-dielectric BNC male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. Their gold-plated center conductors are hand soldered and inspected. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. When you are looking for pre-assembled BNC male cable assemblies and want a high-quality, reliable product, look no farther than our own DX Engineering RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies!
( 38 )
$52.99
—
$65.99