Filters
3 Results Found For "hex"
DX Engineering Utility Enclosure Kits
DX Engineering Utility Enclosure Kits are ideal for the outdoor mounting of many types of lightning protectors or other equipment. This enclosure and grounding plate kit accommodates coaxial protectors with a flange mount or bracket so connectors are parallel with the grounding plate. (Bulkhead protectors that mount the connector through a grounding panel cannot be used.) DX Engineering DXE-UE-2P Utility Enclosure kits are manufactured from weather-resistant, high-impact thermoplastic material that protects the inside components against rain and directed water spray. The housing and wire entrance grommet materials used in the enclosure are fire-retardant and UV-stabilized and resist degradation from weathering, environmental contaminants, chemical fertilizers, and insecticide sprays. The exterior of the housing may be painted with latex or oil base paints if needed to help blend into the location. Because these kits have many potential applications, no holes have been drilled in the enclosure. However, mounting holes have been pre-drilled in the aluminum mounting plate. Four of the six sheet metal screws are included to secure the mounting plate to the enclosure; the other two sheet metal screws are for mounting the copper strap clamp to the mounting plate. Watertight feedthrough couplers mount to the top of the enclosure; drilling or cutting with a hole saw is required. Eleven port openings exist in the bottom--two are large for conduit coaxial entry/exit, and nine are smaller for coaxial cable, rotor cable, Telco lines, and more. All openings are sealed by a weathertight foam insert. NOTE: The DXE-UE-2P accommodates coaxial protectors that have a Flange Mount bracket, or those that work with an accessory bracket, to mount the connectors parallel with the grounding plate. Bulkhead Mount protectors that place a connector through the grounding plate cannot be used. These kits include: * 13 in. W x 14 in. H x 4 in. D enclosure (11-1/2 in. W x 11 in. H x 3-1/8 in. D) * 6 stainless steel hex washer head slotted sheet metal #8 x 1/2 in. screws * 8 in. W x 11.0 in. H x 1/8 in. D pre-drilled 6061-T6 aluminum mounting plate * Four weathertight coaxial cable feedthrough couplers, ideal for most RG8U or RG-213 sized coaxial cable * One 2 in. x 1/2 in. x 1/8 in. thick copper strap clamp with two drilled holes Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Provide proper protection for your weather-sensitive connections. Use DX Engineering Utility Enclosure Kits to supply the environmental safeguard you need!
( 79 )
$92.99
DX Engineering UCGC-Z Universal Copper Grounding Clamps
DX Engineering Universal Copper Grounding Clamps, model DXE-UCGC-Z, are custom designed to provide a ground rod mounting solution for various types of lightning protectors commonly used for Amateur Radio. The "Z" design makes it easy to install and remove coaxial cable connectors. This ground rod clamp for surge protector mounting is ideal for permanent installations as well as for temporary installations, such as Field Day. The DXE-UCGC-Z Copper Grounding Clamp Features: - Mounts up to six protectors onto one ground rod - Fits common standard 5/8 in. through 3/4 in. diameter ground rods - Made from 1/16 in. thick Copper Alloy 110 for maximum conductivity -"Z" bends in the copper for easier installation and removal of coax connectors on protectors - Easy to assemble two-piece construction. Each plate is approximately 3-1/4 in. wide x 4-3/16 in. tall - Stainless Steel hardware is included: Four 1/4 in.-20 x 3/4 in. long hex head bolts, eight 1/4 in. flat washers, four 1/4 in.-20 Nyloc hex nuts - Using this copper clamp is faster and easier than building up the joint for an exothermic weld The DXE-UCGC-Z can easily mount up to six lightning protectors. The photo shows two DX Engineering and two PolyPhaser lightning protectors installed on a DXE-UCGC-Z mounted to a 5/8 in. diameter ground rod. Other lightning protection products can also be mounted, such as the DXE-IS-RCT Control Line Protector and Alpha Delta Lightning Protectors. Additionally, a solid copper strap from the station grounding bus bar may also be sandwiched between the copper plates of this clamp and the ground rod (not shown). An anti-seize compound such as JTL-12555 Jet Lube SS-30 Pure Copper Anti-Seize must be used on the threads to prevent galling or seizing of stainless steel hardware. All connections must be generously coated with a conductive joint compound to prevent moisture penetration and enhance conductivity. Properly weatherproofing coaxial cables and lightning protectors is important to ensure the longevity of the connection and maintain optimal performance. Prior to attaching the lightning protectors, install the coaxial cables to the lightning protectors and weather seal the PL-259 connectors using TES-2155 Temflex Rubber Sealing Tape with an overwrap of TES-06132 3M Super 33+ Vinyl Tape or 3M Scotch Super 88 Premium Vinyl Tape (TES-06143). These easily removable connector sealing tapes are now available in kits. The lightning protector bodies are not weatherproof and it is suggested to use a DX Engineering Weatherproofing Kits to permanently cover the body of the protectors. Some users have also suggested covering the entire assembly with a plastic food container or plastic trash bin As with all electronic equipment, take proper safety considerations. For example: Do not install if there is a storm anywhere in your area. Do not adjust or touch the grounding system equipment when there is a storm anywhere in your area. Make sure all power is removed before making any adjustments or working on any ground system or grounding components. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Complete your coaxial cable grounding installation with DX Engineering UCGC-Z Universal Copper Grounding Clamps.
( 40 )
$65.99
DX Engineering Ground Bus Hardware Packs
DX Engineering Ground Bus Hardware Packs include the original 24-piece hardware that comes with the DXE-GBWM-W: (4) - 1/4 x 20 hex head stainless steel (4) - 1/4 in.-20 hex nuts (4) - 1/4 in. flat washers (4) - 1/4 in. split washers (4) - 1/4 in. external tooth washers (2) - ring terminals (2)- wire lugs Bus bar mounting hardware is not included due to a variety of mounting surfaces and hardware requirements.
( 1 )
$20.99