Filters
4 Results Found For "in-line"
DX Engineering Grounding Clamps
DX Engineering Grounding Clamps are used to connect wire grounding conductors of AWG 2 through 10 to a ground rod, tower leg or grounded pipe. These clamps are manufactured from cast bronze, a highly conductive copper alloy, and include high quality 1/4-20 stainless steel screws for maximum longevity and durability. These clamps also accept the stud from our IS-RCT control line protectors, to provide the proper protection of rotator control lines at the base of a grounded tower. Please note that pipe is measured by ID, not OD. For example, 1-1/4 pipe is much larger than 1-1/3 in. OD. DX Engineering Grounding Clamps are available in two sizes, to fit your grounding project. These are great general purpose grounding clamps to have on hand for future projects, so add a few to your order today!
( 8 )
$16.99
ERICO Ground Rods
Many hams are misinformed about the importance of proper grounding. It's paramount for safety and station efficiency to have an excellent grounding system. In any grounding system, the ground electrode provides the physical connection to the Earth and is the essential instrument used to dissipate current. ERICO Ground Rods provide the superior Earth connections you need! ERICO has decades of experience and offers a complete line of ground rods to meet Amateur Radio and industry needs. ERICO Ground Rods have these great features: * 99.9 percent pure electrolytic copper coating * Manufactured of high strength 1018 cold drawn steel * Specifically manufactured to work with other ERICO/CADWELD products, like ONE SHOT * Molecular bond to nickel-sealed high strength steel core * Copper coating will not crack when bent or tear when driven * Rods have a high carbon steel core and tip that provide superior strength when driving * Resist corrosion better than galvanized rods allowing for approximately 30-year service life in most soils * Minimum tensile strength of 80,000 psi and straightness tolerance of .010 in. per linear foot * State of the art manufacturing process helps ensure uniform plating thickness * ERICO name, length, diameter and part number is roll-stamped within 12 in. (304.8 mm) of chamfered end * UL logo and control number where applicable stamped on each rod for easy inspection after installation * Minimum copper coating of 10 mils on Rods Listed To Meet UL 467 * Exceed the requirements of ANSI®/UL® 467, CSA, and ANSI/NEMA GR-1 ERICO Ground Rods are a vital part of your station and antenna grounding systems. These superior ground rods will guarantee an efficient Earth ground and enhance your station's safety and efficiency. Order your ERICO Ground Rods from DX Engineering!
( 27 )
$17.29
DX Engineering Electronic Protection Components
DX Engineering Electronic Protection Components may be used in a variety of electronics and radio applications. These are wire lead components that can be used on circuit boards or in multi-purpose connection devices. Choose from the components listed for detailed specifications: DXE-MOV-82VDC-10 Metal Oxide Varistor, Surge Protector, max. 82VDC/50VAC Pack of 10 DXE-GDT-4KV-5 Gas Discharge Tube, Surge Arrestor, 4kV, Pack of 5 DXE-TVS-1500-10 ESD Suppressor, TVS Diode, Bidirectional, 17VDC max., Pack of 10 DXE-CAP-PT1UF-10 Capacitor, Ceramic, 0.1uf, 1kV DC, RF Bypass, Pack of 10 ---------------------------------------------------------------------------------------------------------------------------------- This series of protection components are well suited for the DXE-CLTB Control Line Terminal Board that provides a flexible and simplified approach to control line surge protection. The DXE-CLTB is a small, 3 inch square printed circuit board (PCB) with four ten-wire compression screw terminal blocks that handle from 14 to 26 AWG conductors and up to 10A. The two outer terminal blocks are for input and output of the control wires and the two 45 degree angled ten-wire compression screw terminal blocks are for connecting electronic surge protection components. This provides for the choice of components to install between the control line and ground to provide shunt protection. Metal Oxide Varistor (MOV), Gas Discharge Tube (GDT), EMP Suppressor TVS Diodes, RF Bypass Capacitors and other wire lead components are easily connected between the control lines and ground. For effective protection wherever shunt devices are used, a low impedance ground is critical. The DXE-CLTB Control Line Terminal Board has four corner grounding screw holes for mounting on metal standoffs to a metal grounding panel inside an enclosure. DXE-CLTB-M Control Line Terminal Board includes a 10-pack of MOVs.
( 1 )
$11.99
—
$15.99
DX Engineering Weatherproofing Kits
DX Engineering Weatherproofing Kits weatherize your outdoor connections and prevent moisture entry and corrosion with vapor wrap and high quality electrical tape. When your non-weather resistant equipment needs to be mounted outdoors, these weatherproofing kits provide needed protection. Use these kits to protect lightning protectors, coaxial connections, antenna joints, steel hardware, junction boxes and just about anything you can wrap with tape by using these kits. The non-conductive malleable vapor wrap sealant is water-impermeable and withstands temperatures from minus 65 degrees F to plus 180 degrees F without cracking. Choose from Standard, Upgraded or Ultimate kits with different grades of vinyl tape. The WK-PRO Kit has more vapor wrap material and five rolls of tape for large projects. See each kit's detailed description. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Reliable waterproofing is important to protect equipment and cable connections from damage caused by moisture penetration. Protect your equipment, handle extreme temperatures, and remain unaffected by water and UV sun rays with DX Engineering Weatherproofing Kits.
( 19 )
$15.99