Transceivers and Receivers
Availability
HAM Radio Transceivers & Receivers
Your world of Amateur Radio communications or shortwave listening begins with a transceiver or a receiver from DX Engineering! We carry a wide variety of transceivers...
Your world of Amateur Radio communications or shortwave listening begins with a transceiver or a receiver from DX Engineering! We carry a wide variety of transceivers and receivers from Alinco, Icom, Kenwood, and Yaesu, and accessories from MFJ, Nifty, bhi Ltd., West Mountain Radio, LDG and many others! We have the right rig for your favorite operating bands and modes—CW, SSB, AM, RTTY, PSK, JT65 and beyond. Choose from base receivers, entry-level transceivers, mobile transceivers for extra versatility, or all-mode transceivers and cutting-edge deluxe transceivers for contesting and chasing DX. We’ll help you maximize...
Your world of Amateur Radio communications or shortwave listening begins with a transceiver or a receiver from DX Engineering! We carry a wide variety of transceivers and receivers from Alinco, Icom, Kenwood, and Yaesu, and accessories from MFJ, Nifty, bhi Ltd., West Mountain Radio, LDG and many others! We have the right rig for your favorite operating bands and modes—CW, SSB, AM, RTTY, PSK, JT65 and beyond. Choose from base receivers, entry-level transceivers, mobile transceivers for extra versatility, or all-mode transceivers and cutting-edge deluxe transceivers for contesting and chasing DX. We’ll help you maximize your new or existing rig with transceiver filters, plug-in modules, remote meters, interface devices, handles and many other available accessories. Communicate and listen to your world, as you desire, with a transceiver or receiver from DX Engineering.
Yaesu DC Adapters and Cables
Yaesu DC Adapters and Cables are available for several models to keep your portable radio charged and running. Most of these cables will plug directly into the portable radios, and some will plug into a charging cradle, sold separately. Yaesu DC Adapters and Cables are available to keep your radio on the air.
( 38 )
$37.99
STAMPFL HAM Electronics VT5-S Active HF Receiver Multicouplers
STAMPFL HAM Electronics VT5-S Active HF Receiver Multicouplers were developed according to a design by Günter Fred Mandel DL4ZAO especially for SWL (Shortwave Listener) covering 9 kHz to 52 MHz. The VT-5S distributes a single near zero-Ohm star point (HF antenna input) to five outputs with a passive distribution network. This decoupling of the individual outputs prevents connected devices from influencing each other without level losses using a low-noise, high-dynamic RF amplifier and a push-pull output stage. These HF Multicouplers ensure high signal stability, minimal self-noise, and strong isolation between outputs. Additional protections include ESD protection on the input and short-circuit protection for the bias-T, which can remotely power active antennas. The VT5-S Multicoupler is designed to supply an external stabilized DC voltage . With an operating voltage in the range of 11.7 to 15VDC. The DC voltage must be free of hum and noise. The current consumption is approx. 150mA (at 13.8VDC). The DC supply is connected via a center positive 2.1mm ID (5.5mm OD) DC barrel plug. With its compact, lightweight design, the VT5-S delivers reliable performance for professional and hobbyist HF monitoring stations.
Not Yet Reviewed
$309.71
ICOM Handheld Cigarette Lighter Cables
Keep your radio powered at all times with one of these ICOM handheld cigarette lighter cables. Available for several models, these cables will plug directly into some handheld radios, and others will require a charger unit, sold separately. Regardless, ICOM handheld cigarette lighter cables will keep you powered or charged and operating for hours.
( 3 )
$46.99
Icom IC-7300MK2 HF/50MHz Base Transceivers
Icom IC-7300MK2 HF/50MHz Base Transceivers are an advanced evolution of the original IC-7300, designed for superior performance and equipped with modern connectivity. Connectivity upgrades include a first for Icom HF transceivers: the MK2 integrates an HDMI™ output for external display of spectrum scope, waterfall, and audio. Additionally, USB Type-C™ interfaces with dual virtual COM ports and audio I/O enable simultaneous use of digital modes and logging software, while LAN ports provide simplified RS-BA1 remote control without the need for a base station PC. The IC-7300MK2 features an improved Reciprocal Mixing Dynamic Range (RMDR) of approximately 105dB at 2kHz separation and transmit phase noise reduced to –139dBc/Hz at 1kHz offset, delivering cleaner signals and enhanced adjacent-signal handling. Power efficiency is optimized with standby current reduced from 0.9A to 0.7A, minimizing heat generation for stable long-duration operation. Additional enhancements include built-in CW decoding, RX antenna IN/OUT connectors for external filters or preamps. These refinements make the IC-7300MK2 a high-performance, feature-rich solution for serious HF operators seeking cutting-edge SDR technology with robust remote and display capabilities
( 31 )
$1,499.95
FlexRadio 8400 Signature Series HF/6-Meter SDR Transceivers
FlexRadio 8400 Signature Series SDR Transceivers offer the latest in high-performance, direct sampling software-defined radio (SDR) technology designed for the HF and 6-meter amateur bands. Designed for hams who operate exclusively via remote access, the FLEX-8400 is engineered as a server-based SDR transceiver. It supports SmartSDR clients on Windows, Mac, iOS, and Maestro, allowing seamless control from virtually anywhere. With dual independent receivers and full duplex cross-band capability, it's ideal for DXing, contesting, and digital modes—no external sound cards or interfaces required. Using a PC, laptop, or Mac client, the FLEX-8400 supports up to two 7 MHz spectrum/waterfall displays and independent receivers, providing enhanced band visibility. Both receivers can operate simultaneously on any band and mode, with instant QSY between VFOs. Digital mode operation is streamlined—no sound cards, cables, or external interfaces required. The radio delivers advanced band awareness, low phase noise, brick wall filters, and high-quality audio performance to support a wide range of operating styles.
( 4 )
$2,499.00
Instant Rebate
Manufacturer Rebate
ICOM IC-705 HF/50/144/430 MHz All Mode Portable Transceiver
Icom IC-705 HF/50/144/430 MHz All-Mode Portable Transceiver brings the advanced features of the IC-7300, IC-7610 and IC-9700 to a portable QRP package. It features SDR Direct Sampling technology for low noise and low distortion receiver performance and incredible voice and digital transmission capabilities. Along with the same color touch screen and high speed, high resolution of the real-time spectrum scope and waterfall display, the rich set of features in the IC-705 will easily place this radio as the "Best Ever" All-Band All-Mode Portable! Here are many of the advanced features of the Icom IC-705 Portable Transceiver: * "Base Station" performance in compact package that you can hold with one hand! * Dimensions (WHD): 7.9 x 3.1 x 3.3 in. (20.0 x 8.0 x 8.5 cm) * All-band All-mode Transceiver Capability: 160-6m+2m+70cm; SSB/CW/RTTY/AM/FM/DV (D-STAR) * Full D-STAR capabilities including DR mode and Terminal Mode/Access Point Mode * Send, receive and view images on the IC-705 with no application software required * "General Receive" coverage from MW through 148 MHz, 430-450 MHz * Receives AM and FM Broadcast Bands and Air Band * Output power is 10W on external 13.8V supply or 5W with included clip-in rear panel battery pack (BP-272 Li-ion); supports QRP and QRP operation down to 0.5 W * 4.3 in. color touchscreen display – same as used in the Icom IC-7300 and IC-9700 * High-speed, high-resolution, real-time spectrum scope and waterfall display * SDR Direct Sampling below 25 MHz and Down-conversion IF above 25 MHz * Built-In GPS tracking logger, repeater locator and finds nearby D-STAR repeaters * USB port (micro-B) for direct interface * Wireless LAN (802.11 b/g/n Wi-Fi) for remote operation * Bluetooth - supports smartphone linking, remote control and Bluetooth wireless headsets and headphones * microSD Card Slot (microSD card not included) * Includes HM-243 Speaker/Mic with multi-function buttons * Optional LC-192 Multibag Backpack for easy portable operations Note: A single BNC antenna connector functions for all bands
( 127 )
$1,399.95
FlexRadio 8400ATU Signature Series HF/6-Meter SDR Transceivers
FlexRadio 8400ATU Signature Series SDR Transceivers offer the latest in high-performance, direct sampling software-defined radio (SDR) technology designed for the HF and 6-meter amateur bands. Designed for hams who operate exclusively via remote access, the FLEX-8400 is engineered as a server-based SDR transceiver. It supports SmartSDR clients on Windows, Mac, iOS, and Maestro, allowing seamless control from virtually anywhere. With dual independent receivers and full duplex cross-band capability, it's ideal for DXing, contesting, and digital modes—no external sound cards or interfaces required. The integrated automatic antenna tuner (ATU) is designed to match antennas with up to 3:1 SWR on 80–10 meters and up to 2.5:1 SWR on 160 and 6 meters. Using a PC, laptop, or Mac client, the FLEX-8400 supports up to two 7 MHz spectrum/waterfall displays and independent receivers, providing enhanced band visibility. Both receivers can operate simultaneously on any band and mode, with instant QSY between VFOs. Digital mode operation is streamlined—no sound cards, cables, or external interfaces required. The radio delivers advanced band awareness, low phase noise, brick wall filters, and high-quality audio performance to support a wide range of operating styles.
( 2 )
$2,849.00
On Sale
ICOM IC-718 HF All Band Transceivers
ICOM IC-718 HF All Band Transceivers make communicating with the world easy! The superior performance of these HF base transceivers allows you to make contacts over long distances--even to the other side of the world! With excellent receiver sensitivity, a wide dynamic range, high signal-to-noise ratio, and full-duty operation, the ICOM IC-718s offer the latest RF and digital technology in a compact size. Clean, clear audio is easily heard from the front-facing speaker and the IC-718s feature a minimum of switches and controls to simplify operation. Plus, a soft-touch 10-key pad allows for the direct entry of an operating frequency. These are great HF starter transceivers but they will also thrill the accomplished ham, because the IC-718s are very simple to use. The IC-718 HF All Band transceivers will definitely be the most practical DSP rigs you will ever own! They provide many useful features that you want and need--and the price isn't bad, either! Some quick specs: * 160 through 10 meter operation (60 meter channels not available) * Continuously adjustable RF power output -- 100 watts maximum to 2 watts minimum (SSB and CW modes) -- 40 watts to 2 watts (AM mode) * 30 kHz through 30 MHz general coverage receiver * 1 Hz frequency resolution * 101 memory-scan channels Other great features include: * Includes DSP noise reduction and auto notch (UT-106 module) * RF gain control * RF attenuator and preamplifier * Adjustable level noise blanker * IF shift control * Receiver Incremental Tuning (RIT) * Band stacking register * Tuning rate auto step-up function * Digital S/RF meter * VOX operation * Adjustable microphone audio compressor * Electronic CW keyer Note: For additional information, please look at the files under the "Documentation" tab. Supplied accessories include: * Hand-held microphone * DC power cable and spare fuses These little transceivers are great for portable use or as Field Day equipment. They also make great back-up transceivers for well-equipped ham shacks. New Ham or not, one of these IC-718s is a nice addition to any station. Order ICOM IC-718 HF All Band Transceivers from DX Engineering and enjoy some easy QSOs.
( 47 )
$1,099.95
$899.95
ICOM CX-10G 10 GHz Transverters
ICOM CX-10G 10 GHz Transverters are high-performance RF transmit and receive converters designed for amateur radio SHF enthusiasts and radio experimenters. Fully compatible with ICOM IC-905, the CX-10G Transverter converts 2.4 GHz IF signals to the 10 GHz band, opening a new range of frequencies for experimentation and communication. The CX-10G compact and lightweight unit that connects directly to, and is powered by the IC-905 RF Unit. This 0.5-watt output 10 GHz Transverter is also fully IPX5 waterproof for tower or tripod mounting at the antenna to limit cable loss. It features a built-in preamplifier and uses the RF Unit GPS signal for an ultra-stable local oscillator, ensuring excellent sensitivity and signal stability. A variety of protection circuits are built-in to prevent damage from overvoltage, overcurrent, and overheating. These transverters also include a range of useful features such as adjustable output power, a low noise figure and a built-in cooling fan to keep the unit operating smoothly even during extended use. Whether you are a seasoned SHF experimenter or a curious operator looking to explore the 10 GHz band, the Icom CX-10G 10 GHz Transverter is a powerful and reliable tool that is sure to impress. Along with the Icom IC-905, this transverter unit makes it easy to try the 10 GHz band and take your operations to the next level.
( 1 )
$1,199.95
Alinco DR-MD500T Advanced Dual Band VHF/UHF DMR Mobile Transceivers
Alinco DR-MD500T Advanced Dual Band VHF/UHF DMR Mobile Transceivers add to its existing line-up of Digital Commercial/Business or Amateur Radio products. The DR-MD500T has features such as Color LCD Display, 55W Output Power on VHF, and 40W on UHF, as well as up to 4,000 Memory Channels, 10,000 TalkGroup, and up to 300,000 contact lists. Capable of operating in digital and analog with mixed mode in VFO or Memory mode. The DR-MD500T utilizes DVSI's AMBE+2 vocoder for crystal clear DMR digital audio for use in noisy environments like construction sites, parks, security applications, or your favorite repeaters coverage area with no noise or fading even in low lying areas. The DR-MD500T has powerful 2W audio output power to ensure loud crisp receive audio. Alinco DR-MD500T features: * DMR Tier I and Tier II * MAX output power 55 watt (VHF)/40 watt (UHF) * 4,000 channels, 250 zones, 250 scan lists * 300,000 digital contact list * Large 1.77 in. LCD display * Automatic Repeater Roaming * Single or dual channel selectable * Displays DMR ID, Call sign, Name * X-band repeat, analog uplink/digital downlink or vice versa * FM Broadcasting receiver with 100 memory channels and VFO * AES 256bit Encryption (digital mode) * SMS (digital mode) * Communication recording (digital mode) * Individual/Group/All call (digital mode) * CTCSS/DCS/DTMF/2Tone/5Tone encode and decode (analog mode) * Allows CSV export/import of setting parameters * Programmable Auto Repeater Shift in VFO mode * Kill and Stun functions * VFO/MR switch * FCC Part 90 certified
( 11 )
$379.95
Fobos Wideband General Purpose SDR Receivers
Fobos Wideband General Purpose SDR Receivers offer exciting functionality designed to elevate your radio communication experience. This is a high-performing Software-Defined Radio receiver encased in a sleek, attractive blue aluminum body. Equipped with High-Speed USB 3.0, Fobos SDR ensures quick data transfer and easy device connectivity. The compact and EMI-shielded construction further enhances its durability, making it ideal for a variety of challenging environments. We are proud of the primary features of our new Fobos SDR • Broad Frequency Range: Fobos SDR offers a continuous operating frequency range from 100 kHz – 25 MHz (direct sampling) and 25 MHz – 6 GHz (double conversion heterodyne). • High-Quality Signal Conversion: Dual conversion, two HF channels, 14-bit ADC, 50 MHz IQ rate. • Continuous Data Stream: Uninterrupted recording and real-time analysis. We've enhanced Fobos Software-Defined Radio (SDR) receiver with updated features and improvements. • Added a custom GPO port for 8 lines (general purpose output – software-controlled digital outputs) for remote control of the SDR. • Improved frequency response. • Added protection against static electricity and input voltage surges. • Minimized influence of parasitic harmonics and improved resistance to noise. • The low-pass filter for HF1 and HF2 is designed for a cutoff frequency of 24 MHz. • Improved stability of USB stream. All functions mentioned above can be performed simultaneously! Fobos SDR also offers robust software support, compatible with Windows and Linux platforms. It includes a lightweight API, support for an external clock input, and straightforward driver installation that ensures a smooth user experience. Additionally, it is widely compatible with popular software such as SDRSharp, HDSDR, SoapySDR, Delphi library, GNURadio, and HDSDR ExtIO plugins, along with native uSDR support. All source codes are available on GitHub page and provided with LGPL-2.1 license. This is the best quick start SDR Receiver kit for additional software development, education and equipment evaluation. FOBOS Wideband General Purpose SDR Receivers are an excellent choice for hobbyists, researchers, and professionals in the field of radio communication, providing tools to fully leverage SDR technology.
Not Yet Reviewed
$485.00
Yaesu SSM-BT20 Bluetooth Mini Headsets
Yaesu SSM-BT20 Bluetooth Mini Headsets represent an ideal choice for those in pursuit of untethered communication. They boast a streamlined design, suitable for handheld radios and mobile phones and offer seamless, interference-free communication. This state-of-the-art Bluetooth headset is compatible with an extensive array of devices, including the Yaesu FT-3DE, Yaesu FT-3DR, Yaesu FTM-300DE, Yaesu FTM-300DR, Yaesu FTM-6000E, Yaesu FTM-6000R, among others. The SSM-BT20 model is equipped with a high-grade microphone, integrated with a multi-functional PTT button that can also be utilized to answer mobile phone calls. It features two volume buttons, a status LED, and two interchangeable earphone inserts with detachable open ear hooks, ensuring maximum comfort. The headset is specifically engineered for environments with low to normal noise levels. The Bluetooth headset is capable of transmitting audio up to approximately 32 ft. (10 meters) with excellent quality. This implies that the radio or mobile phone does not necessarily need to be always carried on the person. However, it is recommended to test the range in the specific environment of use to guarantee signal quality. The SSM-BT20 Bluetooth headset is supplied with a USB charging cable, enabling charging via any USB port. Whether it's a USB power adapter, USB cigarette lighter adapter, computer, notebook, or power bank, the headset can be charged with ease and convenience. Additional Features and Specifications: -Bluetooth version Ver 4.1 (profiles HSP, HFP), max. 32.81 ft. (10m) range (class 2) -Built-in lithium polymer battery -Intelligent Noise Reduction -Standby time with one battery charge: up to 400 hours -Talk time on one battery charge: up to 12 hours (continuous talk) -Dimensions: 2.362 x 0.866 x 0.591 in. (60 x 22 x 15mm) -Operating temperature: -4° F to 140° F (-20 to +60 degrees Celsius) -Charging temperature: 32° F to 113° F (0 to +45 degrees Celsius)
( 5 )
$49.99
Alinco DR-138TMKII 2 Meter Mobile Transceivers
Alinco DR-138TMKII 2 Meter Mobile Transceivers deliver up to 70W of output power with selectable 70W/25W/10W (H/M/L) settings. Advanced noise reduction and voice commander technology provide exceptional audio clarity, even in noisy environments. Built for durability, the DR-138TMKII features a cooling fan to maintain optimal performance during extended operation. With 200 memory channels, wideband FM broadcast, and air band capabilities, the DR-138TMKII offers versatility and includes a wide variety of selective calling features such as built-in 2-Tone, 5-Tone, 50 CTCSS, 114 DCS, 4 Tone-burst tones, and DTMF/ANI decode, plus radio stun/kill/revive functions for enhanced communication security. The large, bright LCD and easy-to-operate backlit keys, paired with a multi-function backlit microphone for direct frequency entry, make operation intuitive. Additional features like various scan modes, key lock, and wide/narrow operations are included.
Not Yet Reviewed
$229.95
Heil Sound HTH Series Handie-Talkie Headsets
Now you can have Heil Sound quality for your HT! Heil Sound HTH Series Handi-Talkie Headsets are single-sided or double-sided lightweight headsets with adjustable boom mics, designed for use with many popular handheld transceivers. These headsets provide hands-free and discreet two-way communication while maintaining the comfort necessary for extended use in moderate noise environments. The single-side models feature a left or right ear adaptable earpiece and both single and double include an in-line Push-to-Talk switch. HTH and HTHD headset details: * Microphone Element: Electret * Frequency Response: 100 Hz to 10 kHz * Polar Pattern: Omni * Impedance: 2.2 k ohm * Weight: 2.7 oz. * Required Adapter: None** HTH Series headsets are available with three pin-out configurations- ICOM, Yaesu, and Kenwood/Baofeng. HTH-I and HTHD-I: Works with 2-pin Icom HTs and IC-705*** HTH-Y and HTHD-Y: Works with single pin TRRS Yaesu/Vertex HTs (not FT-25, FT-65 and not FT-4XR)** HTH-K and HTHD-K: Works with 2-pin Kenwood/Baofeng HTs, no adapter cable needed **For the weather-resistant Yaesu/Vertex models, such as the VX6R and VX7R, use the HTH-Y or HTHD-Y headset and a Heil HTH-ADY adapter cable. Works with Yaesu CT-131 for VX8DR. ***For HTH-I and HTHD-I used with ICOM HTs having 2-pin plugs, no adapter cable is needed. HTHD-I is compatible with the Icom IC-705, in its very tight fitting plug location; use caution and care when unplugging. Hams around the world have used Heil products on their HF base transceivers for decades. Now you may add Heil technology to your portable radio. Order Heil Sound HTH Series Handi-Talkie Headsets from DX Engineering for your HTs!
( 62 )
$45.00
—
$49.00
Instant Rebate
Kenwood TS-890S HF/50MHz Transceiver
Kenwood TS-890S HF/50MHz Transceiver: The most rewarding results often take place when faced with the harshest and most challenging conditions. HF enthusiasts know this all too well because of their love of HF. KENWOOD has the answer. Achieve results through certainty, not circumstance—delivered with impeccable receiver and audio performance. Introducing Kenwood's most advanced DSP transceiver, the TS-890S. Key features of the Kenwood TS-890S HF + 6M Transceiver: * 160-6 meters 100W All Modes * Full Down-Conversion Superheterodyne * Extra-low phase noise Local Oscillator * Built-in Roofing Filters, 15 kHz, 6 kHz, 2.7 kHz, and 500 Hz (270 Hz optional) * 7 in. TFT color display * High-speed Independent Band Scope * Animated Meter display toggles between TS-930 and TS-940 meter styles at a touch! * External display connector (DVI-I) * ANT output for external receiver * RF Attenuator (OFF/6/12/18dB) * Advanced DSP Noise Reduction function * Heavy-duty design delivers transmitter performance and endurance operation * Built-in high-speed automatic antenna tuner for rapid band changes * Encode and decode built-in for CW / PSK / RTTY * 120 channel memory * 3 PF keys (preferred function) * Screen capture * Remote operation via direct LAN connection (see KNS in owner's manual) * Multiple USB connections * KEYPAD jack (add up to 8 external PF keys) Place your order here for the Kenwood TS-890S.
( 33 )
$4,399.95
Instant Rebate
Kenwood TS-990S HF/6 Meter Base Transceivers
The ultimate Contest/DX experience is here! Kenwood's flagship HF model is equipped with the latest technology and represents an entirely new standard in HF Amateur Radio communications equipment. Kenwood TS-990S HF/6 Meter Base Transceivers come equipped with dual receivers for simultaneous reception on different bands. They also feature narrow-band roofing filters on the main receiver in a full down-conversion configuration. TS-990S features include: * Down-conversion for all amateur bands on main RX * Newly developed mixer achieves 40dBm IP3 * Narrow-band High-IP roofing filters * Comes with 0.1 ppm TCXO * DSP for main receiver, sub-receiver and band scope * Advanced AGC control * Extensive interference and noise reduction functions * Built-in automatic ATU * Dual TFT displays * USB Firmware Updates * Data mode supported by external I/O switching * Transmit and receive DSP equalizers * Two USB Ports on front panel * Voice guidance/Recording function * Remote control from your PC General details: * TX Frequency range: All Amateur bands 1.8 to 54.0 MHz * General coverage RX: Continuous 30 kHz to 60 MHz * Modes: CW, SSB, FSK, PSK, AM, FM * Stability: Plus/minus 0.1 ppm 32 degrees F to 122 F * Antenna impedance: 50 ohms * ATU range: 16.7 to 150 ohms * Line voltage: AC 120 V (60 Hz) * Power consumption: TX: 720 VA, RX: 120 VA (no signal) * Temperature range: 32 degrees F to 122 F * Dimensions in inches: 18.11 W x 6.50 H x 15.75 D Transmitter Details: * Output power: CW/SSB/FSK/PSK/FM (AM); 200 W (50 W) * Modulation SSB: Balanced, AM: Low Power, FM: Reactance * Spurious emissions: HF (Harmonics) -60 dB or less, HF (others) -50 dB or less 50 MHz -66 dB or less * Carrier suppression: -60 dB or less * Sideband suppression: -60 dB or less * Microphone impedance 600 ohms * XIT variable range: Plus/minus 9.999 kHz * Maximum frequency deviation (FM) wide: Plus/minus 5 kHz, (NFM): 2.5 kHz * Transmit frequency response: Within -6 dB (300 to 2700 Hz) Receiver: * Circuit type: Double or Triple Superheterodyne (depending on band/mode) * Sensitivity (TYP): SSB, CW, FSK, PSK (S/N 10 dB); 0.2 uV (1.705 to 24.5 MHz), 0.13 uV (24.5 to 54 MHz) * Sensitivity AM (S/N 10 dB): 2 uV (1.705 to 24.5 MHz), 1.3 uV (24.5 to 54 MHz) * Sensitivity FM (12 dB SINAD): 0.22 uV (28 to 30 MHz), 0.22 uV (50 to 54 MHz) * Image Rejection HF/(50 MHz): 70 dB/(60 dB) or less * IF Rejection Ratio 70 dB or less * SSB Selectivity 200 to 2800 Hz: 2.4 kHz or more (-6 dB), 4.4 kHz or less (-60 dB) CW, FSK, PSK Selectivity (WIDTH: 500 Hz): 500 Hz or more (-6 dB), 1.2 kHz or less (-60 dB) * AM Selectivity: 100 to 3000 Hz: 6.0 kHz or more (-6 dB), 12 kHz or less (-50 dB) * FM Selectivity: 12 kHz or more (-6 dB), 25 kHz or less (-50 dB) * XIT variable range: Plus/minus 9.999 kHz * Notch filter attenuation: 60 dB or more (Auto), 70 dB or more (Manual) * Beat cancel attenuation: 40 dB or more Note: For additional information, please look at the files under the "Documentation" tab. Get more DX! Contesters and DX Chasers will appreciate every feature on these TS-990 radios. Your time in the shack isn't unlimited. Give yourself every opportunity to make each possible contact. Couple a 200 watt transmitter and one of the most capable receivers on the planet to YOUR antenna system. Order one of your own Kenwood TS-990S HF/6 Meter Base Transceivers from DX Engineering!
( 4 )
$9,699.95
Instant Rebate
Yaesu FTDX10 Compact HF/50 MHz 100W SDR Transceivers
The exciting Yaesu FTDX10 Compact HF/50 MHz 100 W SDR Transceiver utilizes the Yaesu Hybrid SDR configuration - Narrow Band SDR and Direct Sampling SDR - like the FTDX101 series. The Narrow band SDR receiver emphasizes excellent receiver performance, while the Direct Sampling SDR provides a Digital Processing Real-Time Spectrum Scope. This stylish and well equipped model sets a new performance standard for the "affordable class" transceiver. Great for base and portable operations, the Yaesu FTDX10 is ready to order from DX Engineering. Click "More Details" for Features and Specifications Main Features of the Yaesu FTDX10 Compact HF/50 MHz 100W SDR Transceiver: - Narrow Band SDR with 3 types of roofing filters and phenomenal multi-signal receiving characteristics, as in the FTDX-101 series. The Down Conversion type receiver configuration with the first IF at 9 MHz has been adopted for the FTdx10. Excellent narrow bandwidth crystal roofing filters have the desired sharp "cliff edge" shape factor. Thanks to the Narrow Band SDR's latest circuit configuration including 500 Hz, 3 kHz and 12 kHz roofing filters and low-noise oscillator, the RMDR (Reciprocal Mixing Dynamic Range) reaches 116 dB or more, the close-in BDR (Blocking Dynamic Range) reaches 141 dB or more and 3rd IMDR (third-order Intermodulation Dynamic Range) reaches 109 dB or more in the 14 MHz band at 2 kHz separation. - 250MHz HRDDS (High Resolution Direct Digital Synthesizer) affords quiet and clear reception The local circuit of the new FTdx10 uses 250MHz HRDDS method same as the FTdx-101 series. Thanks to its characteristics that improve the C/N (carrier to noise) ratio and the careful selection of components in the design, the phase noise characteristic of the local signal achieves an excellent value of -145 dB or less in 14 MHz at 2 kHz separation. - 3DSS (3-Dimensional Spectrum Stream) on the 5-inch Full-Color TFT Display with Touch-Panel functionality The 5-inch Full-Color panel shows the 3DSS display. By touching the frequency display, the numeric keypad is displayed and the active band and frequency adjustment can be set by direct input. Frequency setting and adjustment can also be performed by turning the MAIN dial or touching the scope display. Similar to the FTdx-101 series, the MULTI display, RX operation status display, Center, FIX and Cursor modes are available. - Front Panel Designed for Superior Operating Efficiency - MPVD (Multi-Purpose VFO Outer Dial), is a large multi-purpose ring around the outside of the VFO dial that enables control of Clarifier, C/S (custom selection function) and recall of memory channels. - Remote Operation with optional LAN unit (SCU-LAN10) is possible with the optional SCU-LAN10 and SCU-LAN10 Network Remote Control Software. In addition to controlling the transceiver basic operations, the versatile scope displays enable sophisticated operations such as monitoring the band conditions on a large display at a location away from the ham shack by connection to a home LAN network. Additional features of the compact Yaesu FTDX10 include: - 15 separate band pass filters - Effective QRM rejection with the IF DSP (IF SHIFT/WIDTH, IF NOTCH DNF, DNR, CONTOUR) - High-quality and super stable final amplifier utilizing the new push-pull MOSFET RD70HUP2 - Aluminum Heat Sink with 80 mm low-noise axial flow cooling fan - High Speed Automatic Antenna Tuner with a large capacity 100-channel memory - RF & AF Transmit Monitor - Microphone Amplifier with Three-stage parametric Equalizer (SSB/ AM mode) - QMB (Quick Memory Bank) - Band Stack Function - Optional speaker – SP-30 designed for the new FTDX10 - Optional 300 Hz Plug-In Roofing Filter– XF-130CN
( 166 )
$1,499.95
Instant Rebate
Yaesu FTDX-101D HF/50MHz 100W Transceivers
The Yaesu FTDX-101D HF/50MHz 100W Transceiver brings new excitement and surprising advances in a particularly attractive package. Its unique hybrid narrow-band SDR configuration achieves unsurpassed critical dual receiver performance. The Direct Sampling SDR section provides astounding visual awareness of activity across the band as well as detail around the operating frequency on each receiver. The large, precision color touch-panel display also features gorgeous dual multi-function meters, dual frequency readouts and multi-functional touch controls, plus the exclusive 3DSS - Three Dimension Spectrum Stream waterfall and panadapter scope. The entire class-leading screen of the FTDX-101D may be displayed on a user supplied external monitor! Ergonomically arranged transceiver controls are centered about a large, tactile and weighted VFO. The Main knob is enhanced with the MPVD; Multi-Purpose VFO Outer Dial which controls the sub receiver VFO, clarifier, VC-Tune RF Preselector**, VFO fine tuning and a user defined Custom Selection function. A welcome feature, each function of the identical Main (A) and Sub (B) receivers have separate independent front panel controls; AF and RF gain, Shift, Width, Notch, Contour, Digital Noise Reduction and APF. Built for the serious contester, dual LED pushbuttons comprise the Active Band Indicator for each receiver, enabling effortless and rapid independent band changes. Adjustments of mode-specific settings and levels are displayed and accomplished quickly with the press-and-turn Multi-function selector. Every important control is strategically placed and readily available for maximum flexibility and ease of operation with this remarkable transceiver. Some of the impressive features and specs of the Yaesu FTDX-101D include: * High-Class 160 to 6 Meters 100 Watt Transceiver for all modes; SSB, AM, FM, CW, RTTY and Digital. * Superb and astonishing close-in dynamic range performance (120 dB RDR at 2 kHz spacing, 14 MHz, 500 Hz) * Hybrid SDR technology: Direct Sampling and NBW (narrow bandwidth) SDR * 9 MHz IF Roofing Filters with excellent Shape Factor * 400 MHz HRDDS (High Resolution Direct Digital Synthesizer) *Ultra-low phase noise 1st Local Oscillator * Completely independent dual receivers with general coverage receive *High-Q VC-Tune Front-End RF Preselector for maximum attenuation of -70 dB (Built-In Main RX, Option for Sub RX) * Yaesu renowned interference reduction system with 32 bit IF DSP and digital noise reduction (DNR) and DSP Auto Notch Many are aware that the iconic model number "101" comes from the legendary and best-selling FT-101 series produced in the 1970s. "The Legend Continues" as this HF transceiver carries the tradition of high quality known of the original 101 series. It is certain to satisfy the demands of a wide variety of Amateur Radio enthusiasts. Today, you may order the Yaesu FTDX-101D HF/50MHz 100W Transceiver from DX Engineering. Click 'More Detail' below to see additional information about the FTDX-101D HF/50MHz 100W Transceivers. The 200 watt version, Yaesu FTDX-101MP is displayed separately in the Base Transceivers area. **NOTE: The Yaesu FTDX-101D has the VC Tune Preselector installed in the MAIN receiver and 12 kHz, 3 kHz and 600 Hz roofing filters installed in the MAIN and SUB receivers. A second VC Tune Preselector is optional for the SUB receiver and four optional roofing filters, 300 Hz and 1.2 kHz for the MAIN and SUB, are available only by transceiver special order. Installation and calibration are done by Yaesu only with a $30 per item labor charge when options are special ordered with the transceiver. The standard model FTDX-101D shipped from stock cannot be internally upgraded by the user. Call DX Engineering to order your standard or custom built FTDX-101D.
( 53 )
$3,749.99
Instant Rebate
Yaesu FTDX-101MP HF+50MHz 200W Transceivers
The Yaesu FTDX-101MP HF+50MHz 200W Transceiver brings new excitement and surprising advances in a particularly attractive package. Its unique hybrid narrow-band SDR configuration achieves unsurpassed critical dual receiver performance. The Direct Sampling SDR section provides astounding visual awareness of activity across the band as well as detail around the operating frequency on each receiver. The large, precision color touch-panel display also features gorgeous dual multi-function meters, dual frequency readouts and multi-functional touch controls, plus the exclusive 3DSS - Three Dimension Spectrum Stream waterfall and panadapter scope. The entire class-leading screen of the FTDX-101MP may be displayed on a user supplied external monitor! Ergonomically arranged transceiver controls are centered about a large, tactile and weighted VFO. The Main knob is enhanced with the MPVD; Multi-Purpose VFO Outer Dial which controls the sub receiver VFO, clarifier, VC-Tune RF Preselector, VFO fine tuning and a user defined Custom Selection function. A welcome feature, each function of the identical Main (A) and Sub (B) receivers have separate independent front panel controls; AF and RF gain, Shift, Width, Notch, Contour, Digital Noise Reduction and APF. Built for the serious contester, dual LED pushbuttons comprise the Active Band Indicator for each receiver, enabling effortless and rapid independent band changes. Adjustments of mode-specific settings and levels are displayed and accomplished quickly with the press-and-turn Multi-function selector. Every important control is strategically placed and readily available for maximum flexibility and ease of operation with this remarkable transceiver. Here are some of the impressive features and specs of the amazing Yaesu FTDX-101MP: - High-Class 160 to 6 Meters 200 Watt Transceiver for all modes; SSB, AM, FM, CW, RTTY and Digital. - FPS-101 Separate External Speaker and Power Supply combination is included - Superb and astonishing close-in dynamic range performance (120 dB RDR at 2 kHz spacing, 14 MHz, 500 Hz) - Hybrid SDR technology: Direct Sampling and NBW (narrow bandwidth) SDR - 9 MHz IF roofing filter with excellent Shape Factor** - 400 MHz HRDDS (High Resolution Direct Digital Synthesizer) - Ultra-low phase noise 1st Local Oscillator - Completely independent dual receivers with general coverage receive - High-Q VC-Tune Front-End RF Preselector for maximum attenuation of -70 dB (Built-in Main and Sub Receivers) - Yaesu renowned interference reduction system with 32 bit IF DSP and digital noise reduction (DNR) and DSP Auto Notch (AN) Click 'More Detail' below to see additional information about the FTDX-101MP HF/50MHz 200W Transceivers. The 100 watt version, Yaesu FTDX-101D is also displayed in the Base Transceivers area. Many are aware that the iconic model number "101" comes from the legendary and best-selling FT-101 series produced in the 1970s. "The Legend Continues" as this HF transceiver carries the tradition of high quality known of the original 101 series. It is certain to satisfy the demands of a wide variety of Amateur Radio enthusiasts. Today, you may order the Yaesu FTDX-101MP HF/50MHz 200 Watt Transceiver from DX Engineering. **NOTE: The Yaesu FTDX-101MP has the VC Tune Preselector installed in the MAIN and SUB receivers. Roofing filters installed in the MAIN and SUB receivers are the 12 kHz, 3 kHz and 600 Hz, plus a 300 Hz is installed in only the MAIN receiver. Three optional roofing filters are available, the 300 Hz for the SUB receiver and 1.2 kHz for the MAIN and SUB receivers. Installation and calibration is done by Yaesu only with a $30 per item labor charge when options are special ordered with the transceiver. The standard model FTDX-101MP ordered on the web, and shipped from stock, cannot be internally upgraded by the user. Call DX Engineering to order your standard or custom equipped Yaesu FTDX-101MP.
( 44 )
$5,098.95
Alinco DR-MD520T Advanced Tri-Band VHF/UHF/DMR Mobile Transceivers
Alinco DR-MD520T Advanced Tri-Band VHF/UHF/DMR Mobile Transceivers are the latest addition to the Alinco Amateur Radio lineup. These advanced tri-band mobile DMR 144/220/440MHz radios come packed with features such as: a large 1.77 in. color LCD display; easy-to-use front panel; a hand microphone with built-in remote-control keypad; and a powerful 2 watts of audio output to ensure loud, crisp receive audio. Power output of the DR-MD520T is 55 watts on the 2 M band, 5 watts on 1.25 M, and 40 watts on the 70 cm band—and can operate in digital and analog with mixed-mode in VFO or Memory mode. A built-in GPS receiver also supports APRS in both analog and digital modes. Store up to 4,000 Memory Channels, 10,000 Talk Groups, 250 zones, 250 scan lists, and up to 500,000 digital contact lists. The DR-MD520T uses DVSI's AMBE+2 vocoder for crystal clear DMR digital audio for Amateur Radio applications or your favorite repeaters coverage area with no noise or fading even in low lying areas. Receiver capabilities include FM Broadcast and AM Aircraft Bands.
( 4 )
$449.95
Perseus22 4-Channel Direct Sampling Receiver
Perseus22 4-Channel Direct Sampling Receiver offers dual continuous frequency coverage from 10 kHz to 225 MHz with typical image rejection greater than 70dB, and excellent dynamic range on four independent receivers, two VLF-HF and two VHF, each with a dedicated antenna input. All four receiver channels are synchronously sampled by a high signal to noise ratio (s/n or SNR), 14-bit A/D converter and processed by a software defined digital down converter, implemented on an FPGA. The four output channels are routed to the host PC via the USB 3.0 controller, achieving synchronized true diversity reception and wide bandwidth IF applications. Supported modes are AM, SAM, QSAM, CW, CWrev, RTTY, RTTYrev, LSB, USB, IQ, FM, WFM (RDS in development), and DAB+. Presently available sample rates are 250, 500, 1000 and 2000 kSps, with the maximum span currently displayed at 1600 kHz. The frequency coverage of the Perseus22 is split-up into pairs of receiving channels (slices), which mean two receivers for the VLF-HF frequency range of 10 kHz to 70 MHz, and two receivers for VHF range from 70 MHz to 225 MHz. Each receiving pair is capable of diversity processing, which can reduce noise by orders of magnitude. Each of the four receiver channels include an analog RF front end equipped with attenuators, preselection filters and amplifiers. The receiver enclosure is machined from solid aluminum and finished with a fine, non-reflective black surface treatment. Perseus22 SDR multichannel software was created by a team formed by Elad and Microtelecom developers, with years of experience in developing software for Digital Signal Processing (DSP). This software takes advantage of an agile GUI interface platform, integrating past DSP design experience to accommodate future modules for demodulators and decoders. This advanced software features a simple and intuitive graphical user interface, simultaneously efficient and complete. The GUI is built using OpenGL, making it possible to leverage the GPU for everything related to the rendering of controls and windows. This allows the CPU to be tasked exclusively with digital processing of the radio signals, to offer revolutionary receiving features and capabilities. Presently this is a Windows software application. Thanks to the libraries used, Perseus22 management software can be implemented on other operating systems such as Linux, MacOS and even Android, with little effort. Perseus22 is shipped with: • AC to DC high-quality medical-grade switch mode power supply GSM40A09-P1J (with AC power cord); 9 VDC 4.45A Output 2.1 x 5.5mm; 80-264 VAC input, IEC320-C14 • USB 3.0 A to B cable, length 76 in. (2 m) • 4 SMA-BNC adapters
( 1 )
$2,579.99
AnyTone AT-6666Pro 10 Meter Mobile Transceivers
AnyTone AT-6666Pro 10 Meter Mobile Transceivers are single band transceivers that provide 80 Watts on CW and SSB (50 Watts on FM). This compact mobile radio has the features you want in a radio: Multi-Mode, adjustable tuning steps, Dual Watch Function, CTCSS/DCS codes, scan function, and is PC programmable. With 99 memories, there is sure to be enough memories to store your commonly used frequencies. Covering all modes on the entire 10-meter band, this compact radio is a perfect fit for today's vehicles. The front panel features a 6-pin connector for the microphone, and the rear panel features an SO-239 for the antenna connection, a speaker jack and the connection jack for PC Programming. Software is available from AnyTone's website. The large display provides information as to the status of the radio including the current mode of the transceiver, frequency, memory channel, status of various functions, and signal strength. It is also possible to change the backlight color to any one of 7 predefined color options as well as the brightness of the display. Additional features include tuning steps ranging from 10Hz to 1MHz, Clarifier, Noise reduction on both Transmit and Receive, squelch and automatic squelch on AM and FM, Repeater offsets, VOX, and a user-defined button on the microphone. The AnyTone AT-6666Pro provides the features that you expect in a compact, professional-grade mobile transceiver. The AT-6666 has modest power needs for a radio that can output 80 watts, requiring only 15A at 13.8VDC and will fit in most vehicles with its small size at 9.92 in x 6.22 in x 1.89 in. Additional Feature and Specifications: • LCD display with 7 color options and back light dimming • FM, AM, USB, LSB, CW, PA modes • Frequency Tuning Steps: 10Hz, 100Hz, 1KHz, 5KHz, 10KHz, 100KHz, 1MHz • ± 500Hz, 5KHz Clarifier (R/T/R+T selectable) • Flexible menu functions and PC programming software • RX and TX NRC Noise Reduction • SQ, ASQ Function (FM and AM mode) • RF GAIN Adjustment • RF PWR Adjustment • VFO / BAND / Memory Channel Modes • Repeater Shift / Offset Frequency Function • CTCSS/DCS with RX/TX Split functions • SCAN Function • NB/ANL Function • DW DUAL-WATCH Function • SWR, S/RF meter Function • TOT function • HI-CUT Function • EMG CALL • SWR Protection • Power Supply Voltage Protection • Key-Lock Function • DTMF Function • BEEP Prompt • Enhanced VOX Function (VOX.SPK can support digital mode operation) • ECHO Function • Programmable RB Function • AM TX NPC • User Defined (PF) key on microphone • Audio path select • +10KHz Function Dimensions: (LWH): 9.92 x 6.22 x1.89 in. Weight: 2.80 lbs.
Not Yet Reviewed
$299.99
SOTAbeams LASERBEAM-817 Digital Audio Filter Modules
Building on the success of their range of LASERBEAM Filter Modules, the LASERBEAM-817 Digital Audio Filter Modules are the perfect addition to your FT-817, FT-817ND or FT-818. Unlike analog filters, digital filters provide near-perfect characteristics. Because of the way that the filters are implemented, they are better than analog filters in almost every way. LASERBEAM-817 modules have been designed to specifically complement the FT-817 or FT-818. It has a new filter line-up, optimized gain for this application; revised switching and a filter select LED. These modules greatly improve the performance of the stock ceramic SSB filter. They also have a far superior shape factor when compared to the aftermarket Collins mechanical filters. These filter modules are applicable whether you have extra filters installed or not. LASERBEAM-817 Modules have two superb digital filters: a 300-2700Hz SSB filter and a 450-950Hz (500Hz) CW filter. These filters have been specifically optimized for the FT-817 or FT-818. The filter switching is fully automatic - no external switches are required. Each LASERBEAM-817 module is supplied with a special integration kit which includes the main parts that you will need to complete your installation. Installing your LASERBEAM-817 module LASERBEAM-817 modules are easy to add - no harder than installing an after-market noise reduction unit. Your FT-817 or FT-817 is a great little radio. Why not make it a bit better with LASERBEAM-818 Digital Audio Filter Modules from DX Engineering!
( 2 )
$81.99
Rugged Radios Patrol Lapel Microphones
Rugged Radios Patrol lapel microphone kits are specifically developed to provide the best audio performance and durability. With their low-profile microphone and the ear-hugging earbud coil, the Patrol lapel microphone is a discreet and comfortable solution to being on the air all day. The included case provides easy storage to protect your equipment and maintain sanitary conditions. Features include: * Rugged, fiber braided cable * Quick-disconnect radio plug * Comfort-Fit semi-custom earpiece * Noise reflecting microphone * Loud and clear audio speaker
Not Yet Reviewed
$59.99