Selected Filters


Filters


Part Groups

Results 1 - 3 of 3

Clearance

Open Box

4O3A A50 Antenna/Load Switches

4O3A A50 Antenna/Load Switches serve as 50-ohm loads for open ports on the HFC4500 combiner or other multiplexer, preventing tuning degradation. Applying 12V power connects the input to the combiner's output, linking it to the corresponding combiner or filter. A typical setup switches a filter or a combiner to a monoband antenna. When the A50 is not powered, the switch defaults to a 50-ohm termination for the input and the antenna output is open. NOTE: The A50 is NOT an A/B switch. The manufacturer's label of "A/B Switch" is a product grouping, NOT an indication of the function of this product. The LOAD resistor is internal, so one of three connectors is unnecessary, which leaves an open hole in the chassis, a "normal feature" of the A50.

Not Yet Reviewed

$181.99


$118.29

Clearance

DX Engineering Multi-Band Dipole Antennas

DX Engineering Multi-Band Dipole Antennas are designs that are rugged, yet lightweight. Using a tuner, they are usable to 30 MHz and come complete with the wire elements, ladder feedline, center T support, and end mount brackets. These antennas are built using the highest quality components. They use 14 AWG stranded-copper, PVC jacketed elements for flexibility and strength and 100 ft. of 18 AWG 300-ohm 0.88 Velocity Factor ladder lines that are UV-resistant. Stainless steel hardware is included. Often, a 4:1 balun is suggested for multi-band dipoles; however, the best balun to use for this application is a 1:1 ratio. The 1:1 baluns provide better balance, have lower loss, and are more tolerant to load impedance and balance variations than other baluns. A tuner balun is not included in the dipole antenna kits and is available separately. The dipole center T support has pre-drilled holes for the attachment of the wire elements, feedline, and support or messenger lines. The center support top hole is used for the attachment of a "messenger line" that can be strung above the antenna wire and is used to provide support for the antenna wire and feedline. The use of the messenger line, which is strongly recommended but not included, will reduce the stress on the element wires and keep the antenna from stretching over time, which will change its resonant frequency. This line can be thin Synthetic Textile rope available from DX Engineering, which has a high breaking strength. Ideally, it should attach to the same structure used for the dipole, only above it, forming at least a 30 degree angle between the dipole and the messenger line. For further information and to decide the amount of rope you will need, please read the included instructions and check your wire antenna area of construction. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you lack the room for more than one antenna or need a multiband antenna for band agility, consider one of these DX Engineering Multi-Band Dipole Antennas as an elegant and economical solution!

4.87 out of 5 stars ( 30 )

$125.99


$100.79

Clearance

Low Band Systems HF Transmit Band Pass Filters

NOTICE: Due to materials supply and logistical issues, resupply of Low Band Systems products will be delayed for an indefinite period. Low Band Systems HF Transmit Band Pass Filters are very high quality multi-stage devices designed to specifically limit the RF band pass to a single Amateur band. They eliminate image and harmonic RF interference issues for dedicated mono-band operations in multi-radio contesting environments. Required for use with transmit multiplexers, these passive filters provide the additional isolation needed to allow multiple transceivers to be operated on different bands simultaneously on the same antenna. Used individually on mono-band radio and antenna combinations, these filters provide the isolation required in multi-radio contest stations. Low Band Systems band pass filters are available for each of the ten HF Amateur Bands in 200, 500 and 1,500 watt models, and 2,000 watt models for the main contesting bands of 160, 80, 40, 20 ,15 and 10 meters. Their unique aluminum enclosures, some with fans, are laser cut with "Perfo-Box" on the side and their power handling and band of operation are stenciled chassis cutouts in European nomenclature, such as "3,5 MHz" for the 80 meter filter, for example. Their permanent demarcation allows immediate identification, preventing any future trouble with faded or missing printed labels. Supplied only with standard UHF Female/SO-239 connectors, these HF Transmit Band Pass Filters achieve over 60 dB of out-of-band suppression that virtually eliminates out of band noise and interfering signals. They are designed to provide a sharp roll off just outside each Amateur band; just below 3.5 MHz and just above 4.0 MHz for the 80 meter filter for example. Low Band Systems filters are the first choice of major multi-multi contest stations around the world! They provide the clear benefit of a dramatically lower noise floor for enhanced single-band weak signal reception desired for elite contest and Field Day operations. Low Band Systems Band Pass Filters are used in conjunction with their multiplexers, also known as multi-band transmit combiners. Low Band Systems Diplexers, Triplexers, Quadplexers and Pentaplexers, also available from DX Engineering, provide good levels of isolation between band ports, but band pass filters are also needed for multi- transmitter operation. This is because the multiplexer's main purpose is to balance the impedances for the multiple-transceiver/single multi-band antenna stations. They provide UHF Female/SO-239 connections for multiple 50-ohm transceivers to be connected to a single 50-ohm feedline. So, band pass filters are REQUIRED for each multiplexer band input to provide the additional isolation required to allow multiple transceiver setups to work. The transceivers for each band are connected to their associated band pass filter, and then to the multiplex device such as a triplexer, which is connected to a tri-band beam, for example. All transceivers can operate simultaneously with up to 80 dB of isolation, unhindered by the signals from the other connected radios operating on the other bands on the same antenna! Achieve the advanced operational advantages that these exceptional filters and multiplexers provide. Order Low Band Systems HF Transmit Band Pass Filters from DX Engineering! NOTE: Filters made for 160 meters are 2.0 MHz low pass models to prevent harmonics on higher bands. They do not reject frequencies below 1.8 MHz. If AM broadcast interference is a problem, an additional BCI filter should be used. After better antennas, these filters are suggested as the most important multi-radio station upgrade by top contest station builders and operators. Low Band Systems HF Transmit Band Pass Filters simply allow more contacts to be made with worldwide DX stations and DXpeditions.

4.86 out of 5 stars ( 28 )

$359.99


$233.99

  • 1
  • Page 1 of 1