Filters
Clearance
COMTEK Jerry Sevick W2FMI Series Current Baluns
COMTEK Jerry Sevick W2FMI Series Current Baluns were inspired by the writing of Jerry Sevick, as published in his book "Understanding, Building, and Using Baluns and Ununs" also available from DX Engineering. COMTEK baluns are value-engineered for maximum performance at a reasonable cost. They provide a superb, efficient transition between unbalanced coax and balanced antennas. COMTEK Baluns feature: * Jerry Sevick design with modern improvements from DX Engineering's in-depth balun research and development * Unique high-voltage compensating capacitors for unequaled SWR bandwidth * Outstanding ferrite-mix coated toroid core with special design to accommodate close coupling without excessive stress * Exceptionally high and consistent common mode impedance across the specified bandwidth, which provides isolation where it is needed most * Special wire size selection and Teflon-insulated wire sleeves provide exact impedance matching and superb insulation, unlike common Thermaleze wire * Typical insertion loss is less than 0.2 dB * Power handling on HF is 3 kW CW and 5 kW SSB on single core models, 5 kW CW and 7 kW SSB on dual core models * May be used to 54 MHz with reduced ratings * Gasketed SO-239 connectors are silver plated and have Teflon insulation * Sealed in a weatherproof 4 in. x 4 in. x 2 in. NEMA box * Stainless steel hardware Note: Polarity markings on baluns are used for matching phase on balanced antennas when stacking beams for a phased array. Also, the positive terminal should be connected to a vertical element or Inverted-L and the negative terminal goes to the radials. For most regular applications on one antenna, including beams, dipoles and most wire antennas, balun polarity doesn't matter. The best Amateur Radio baluns in the world are from DX Engineering. That includes COMTEK Jerry Sevick W2FMI Series Current Baluns!
( 10 )
$104.99
—
$129.99
$68.24
—
$84.49
Clearance
DX Engineering Bead Choke Standoff Kits
DX Engineering Bead Choke Standoff Kits bring a practical solution to a serious problem when ferrite chokes are placed directly onto the metal boom at the feedpoint of beam antennas. A number of Amateur Radio operators and antenna engineers have known for years about the superior choking function of many ferrite toroids beads placed directly on the coaxial cable, as compared to standard feedpoint baluns. A more recent revelation is that the proximity of ferrite beads on coax taped to the aluminum boom of the antenna drastically reduces their effectiveness. DX Engineering Bead Choke Standoff Kits are mounting systems, made of fiberglass or acetyl standoff rods (color varies), PVC carriers and stainless steel hardware, available in four versions. Two sizes of PVC cradle tubes handle two different types of RF bead chokes; 3/4 inch outside diameter (OD) ferrite beads on RG-400 size cable, and 1 inch OD ferrite beads on RG-213 size 0.405 in. coax cable. Each are offered with two different boom size clamps, 2 inch OD and 3 inch OD. Bead Choke Standoff Kits simply hold an RF bead choke and feedline 4 inches away from the metal beam antenna boom (or 4 inches away from the metal mast for a dipole). They maintain the optimal choking performance of ferrite beads on coax. Using DX Engineering Bead Choke Standoff Kits, ferrite bead chokes function at peak performance for these key results: • Prevent feedline radiation of RF • Preserve current balance for proper beam antenna pattern • Prevent feedline shield exterior collected noise and signals from entering the antenna and interior of the feedline, resulting in lower noise floor and enhanced reception The absolute superiority of RF chokes made of many beads on the feedline, over the traditional enclosure balun, is becoming better understood in Amateur Radio. They achieve the best possible RF isolation of the feedline from the antenna and provide completely balanced currents at the feedpoint. Plus, they provide quieter reception with reduction of common-mode noise. Keeping Bead RF Chokes away from metal preserves the optimal function of this method of antenna feedpoint current balance and isolation. This mechanical requirement is simple and practical with DX Engineering Bead Choke Standoff Kits.
( 3 )
$65.99
$52.79
Clearance
DX Engineering Feedpoint Connectors
DX Engineering Feedpoint Connectors provide a direct transition from coaxial cable to feedpoint for Yagi, Loop Fed Arrays (LFA), Rotatable Dipoles and other antennas that do not have a coaxial connector. Three Feedpoint Connector types are available; SO-239 UHF Female, Type-N Female and 7-16 DIN Female. Each Feedpoint Connector (FPC) features silver-soldered solid tinned-copper 12 AWG wire leads to the connector, which is epoxy potted into a plastic housing, 1.573 inch square and 0.787 inch deep, for a weather-sealed direct feedpoint connection. Of course, additional weatherproofing should be applied to the male to female connector junction, as is typically suggested. DX Engineering Feedpoint Connectors' two wire leads are about 4 in. each, for connection to balanced driven elements of beams and rotatable dipoles on which a coaxial connector does not exist. A longer length of wire is easily soldered to these tinned wires, if required, but increasing connection spacing drives up feedpoint impedance and increases the possibility of mismatch. FPCs are ideal for antennas, especially phased antenna pairs or multiples, on which a coaxial cable ferrite RF bead choke is required at the feedpoint, in place of a traditional enclosed balun. DXE-FPC units do not have mounting clamps, straps or holes. They are intended to be supported by the coax cable attachment to the boom or mast and by the connections to the antenna. An appropriate center insulator kit, such as the DXE-UWA-KIT and coaxial cable strain relief, DXE-CSR213-1, can accommodate the use of Feedpoint Connectors SO-239 UHF Female, Type-N and 7-16DIN for specialized and high power wire antennas, also accommodating a ferrite RF Bead Choke on the RG-213U size coax cable, 0.405 in. diameter.
( 8 )
$46.99
$37.59
On Sale
Clearance
Kelemen Trap Dipole Antennas
Kelemen Trap Dipole Antennas are high-quality, heavy-duty pre-assembled wire antennas intended for permanent installations. They feature special traps made with of PTFE (Teflon®) insulated coax for high Q and low losses, offer high performance multi-band operations—and are excellent shortened antennas where there's not enough space for a full-size dipole. Kelemen Trap Dipole Antennas include a series of monoband models, as well as a series of multi-band models that cover an extensive combination of HF bands from 160m through 10 meters. Specific models handle either 400 watts, 1,000 watts or 2,000 watts PEP SSB and CW at resonance. Kelemen Antennas are fully temperature-resistant and weather-proof, and are manufactured from high-quality materials. Balun cases are constructed of transparent, weather-proof polycarbonate with a bottom-mounted SO-239 (UHF female) connector. Hardware and clamps are all stainless steel. Each antenna is completely assembled with the balun, clear PVC-insulated stranded copper wire, stainless wire clamps and egg insulators, ready for operation. Just add rope and coax to complete your Kelemen wire antenna installation. Kelemen Trap Dipole Antennas may be mounted horizontally or in an Inverted-Vee configuration with a central support required. Many Kelemen Antennas are perfect for portable operations because of their low weight. Their coaxial traps are much lighter than conventional traps, making it easier to keep the antenna at an effective height. In many cases they can be easily supported by a single fiberglass pole. For base operations, these antennas should be placed high, in an unobstructed location well away from buildings to limit shifting of resonant frequencies. Kelemen Antennas are often the best possible antenna choice for full-time base operations, offering the advantages of specialized multi-band coverage that perfectly complements the other antennas of the station. Order Kelemen Antennas in North America exclusively from DX Engineering.
( 30 )
$219.99
$164.99
Clearance
VE2DX Electronics SO2R 2X6 Remote Antenna Switches
VE2DX Electronics SO2R 2X6 Remote Antenna Switches provide selection of any six antennas for connection to two radios, covering the frequency range of 1.8 to 60 MHz. All control signals are RFI filtered as are all VE2DX Electronics printed circuit boards (PCB) with shielding on both sides. Each SO-239 (UHF female) antenna port features five relays to achieve a design with over 80db port isolation and full legal limit power handling. The simplicity of this 2X6 design allows the use of only 2 coax cables from the station to the tower. Both radio ports have access to any of the unselected 6 antenna ports. The VE2DX Electronics SO2R 2X6 Remote Antenna Switches is available in both 12VDC and 24VDC versions; the 24VDC version is for installation that requires a longer control line to the Remote Antenna Switch . Each provides a terminal for a 12VDC line inside the weatherproof unit for remote accessories. VE2DX Electronics SO2R 2X6 Remote Antenna Switches may be controlled by third party switch consoles, station controllers and computer automation that supports two sets of 1 of 6 selection. A weatherproof chassis protects the electronics; units should be installed outdoors with connectors facing downward.
Not Yet Reviewed
$624.99
$531.24