Availability
Clearance
Times Microwave Systems® Coaxial Connectors
Times Microwave Systems Coaxial Connectors are innovative designs of the highest quality. Using genuine LMR® connectors and tools will assure reliable connections and quality you can trust. Times Microwave Systems LMR connectors are designed to work perfectly with LMR cables, so choosing and using Times connectors and termination tools assures reliable connections and puts Times quality you can trust to work for you. Although LMR cables through LMR-400 work with just about any manufacturer's connectors, LMR-600 cable requires Times Microwave Systems coaxial connectors. Order your cable and quality Times Microwave Systems Coaxial Connectors from DX Engineering! LMR® is a registered trademark of Times Microwave Systems.
( 38 )
$25.99
—
$45.69
$20.79
—
$34.27
Clearance
DX Engineering F6 75-ohm Coaxial Cable Assemblies
DX Engineering F6 75-ohm Coaxial Cable Assemblies are intended to be used for HF receive antenna systems as well as for cable or satellite TV system use. They are made with a high-quality, 75-ohm, direct-bury, "flooded" F6-type coax and watertight Snap-N-Seal F connectors. Flooded-style feedline, infused with a waterproof compound, have the distinct advantage of automatically sealing small accidental cuts or lacerations in the cable jacket. Plus, the flooding compound works perfectly with the Snap-N-Seal connector's O-rings to provide a reliable, environmentally sealed connection that prevents shield contamination, with no external waterproofing requirement. These low-loss cable assemblies feature a waterproof polyethylene jacket, dual shields, and connectors that are installed with a unique 360 degree radial compression system. A superior RF integrity of over -95 dB external signal rejection means that DX Engineering F6 75-ohm Coaxial Cable Assemblies are your best choice for any high performance system installation.
Not Yet Reviewed
$28.99
—
$29.99
$20.29
—
$20.99
Clearance
Georgia Copper Flexible Ground Strap Jumpers
Georgia Copper Flexible Ground Strap Jumpers are excellent for low impedance outdoor grounding and HF antenna feedpoint and radial system connections. Even weathered to a dull patina, copper strap does not lose its low impedance advantages over wire or cables, for DC and AC through HF and VHF. Plus, flexible copper strap is far superior to tinned copper braid, which holds moisture and disintegrates which causes a undesirable increase in connection impedance over a relatively short time. Flexible SOLID Copper Strap Jumpers come in pre-cut lengths at 1 in. or 3/4 in. widths and 0.022 in. thickness, punched with 0.280 in. holes at each end, to accommodate 1/4 in. bolts. They're available in two-packs at six different lengths, 6 in., 12 in., 24 in., 36 in., 48 in., 72 in. and also in a variety pack that contains one piece of all six lengths. Order and use any of these specific length straps for your project. Or, use your tin snips and your imagination to make all types of low impedance connections for surge protection grounding boxes and panels, protectors, equipment racks, vertical antenna feedpoints, radial system connections and antenna feedpoint connections from a bolt terminal balun to the driven elements. This pre-cut copper strap may also be used as a shack ground bus or for the bus bar connection to the station ground rod or rods. Hobbyists and Electricians order extra copper straps to have on hand and be ready for those grounding and antenna connection projects that come up. Georgia Copper Ground Strap Jumpers are here at DX Engineering, ready for your needs.
( 10 )
$33.99
—
$39.99
$27.19
—
$31.99
Clearance
DX Engineering Feedpoint Connectors
DX Engineering Feedpoint Connectors provide a direct transition from coaxial cable to feedpoint for Yagi, Loop Fed Arrays (LFA), Rotatable Dipoles and other antennas that do not have a coaxial connector. Three Feedpoint Connector types are available; SO-239 UHF Female, Type-N Female and 7-16 DIN Female. Each Feedpoint Connector (FPC) features silver-soldered solid tinned-copper 12 AWG wire leads to the connector, which is epoxy potted into a plastic housing, 1.573 inch square and 0.787 inch deep, for a weather-sealed direct feedpoint connection. Of course, additional weatherproofing should be applied to the male to female connector junction, as is typically suggested. DX Engineering Feedpoint Connectors' two wire leads are about 4 in. each, for connection to balanced driven elements of beams and rotatable dipoles on which a coaxial connector does not exist. A longer length of wire is easily soldered to these tinned wires, if required, but increasing connection spacing drives up feedpoint impedance and increases the possibility of mismatch. FPCs are ideal for antennas, especially phased antenna pairs or multiples, on which a coaxial cable ferrite RF bead choke is required at the feedpoint, in place of a traditional enclosed balun. DXE-FPC units do not have mounting clamps, straps or holes. They are intended to be supported by the coax cable attachment to the boom or mast and by the connections to the antenna. An appropriate center insulator kit, such as the DXE-UWA-KIT and coaxial cable strain relief, DXE-CSR213-1, can accommodate the use of Feedpoint Connectors SO-239 UHF Female, Type-N and 7-16DIN for specialized and high power wire antennas, also accommodating a ferrite RF Bead Choke on the RG-213U size coax cable, 0.405 in. diameter.
( 8 )
$46.99
$37.59
Clearance
SOTAbeams Filter Boards and Band Component Kits
SOTAbeams Filter Boards and Band Kits are used for the WSPRlite Classic, WSPRlite Flexi, or for your own QRP transmitter, SDR front-end filter projects or on any receiver. Choose the Low Pass Filter Board and Band Kit components for the specific bands on which you want to use your WSPRlite. Build these high performance seven-element Chebyshev low pass filters to eliminate harmonics and spurs. They function bi-directionally and may be used for QRP transceivers or for receive. Each board features a manual band change jumper header and comes with a SMA male cable to connect to the WSPR lite and a board mount SMA female connector for your antenna feedline adapter or adapter cable. SOTAbeams Filter Boards and Band Kits are available in four versions. These three have a revised board layout: - SBM-LOWPASSKIT Low Pass Filter Kit for 160, 80 and 40 meters, version 1.2 Board - SBM-LOWPASSKITHB Low Pass Kit for 20, 15 and 10 meters, version 1.2 Board These two include the filter components, connector and one cable. - SBM-PCB3BLPF Low Pass Printed Circuit Board only, version 1.2 Board. This kit includes only the board, SMA connector and one cable. Add to your cart the specific component Band Kits for the bands you want to use. All 11 bands are available from 160-6 meters. After you finish building one of these three boards, it fits into the updated accessory enclosure model DXE-LPFV1-2-CASE. NOTE: These three version 1.2 Boards DO NOT fit into the DXE-SB-LPF-CASE -------------------------------------------------------------------------------------------------------------- - SBM-LPFKITDXEPCB Low Pass Filter Kit for 160, 80 and 40 meters, version 1.1 Board. This kit includes band filter components, connector and one cable with the old PCB. When this v1.1 kit completed, it is the only board that fits into the original DXE-SB-LPF-CASE. (NOTE: This v1.1 board does not fit into the updated DXE-LPFV1-2-CASE which fits only v1.2 boards). --------------------------------------------------------------------------------------------------------------- Buy and build more than one SOTAbeams Filter Boards and Band Component Kits to use your WSPRlite Classic or WSPRlite Flexi on more than three bands. Don't forget to add the adapters shown in suggested parts. These low pass filters also work on QRP transmitters and all receivers. DX Engineering is your source for SOTAbeams and WSPRlite products and accessories.
( 3 )
$39.99
$23.99