Availability
Clearance
DX Engineering F6 75-ohm Coaxial Cable Assemblies
DX Engineering F6 75-ohm Coaxial Cable Assemblies are intended to be used for HF receive antenna systems as well as for cable or satellite TV system use. They are made with a high-quality, 75-ohm, direct-bury, "flooded" F6-type coax and watertight Snap-N-Seal F connectors. Flooded-style feedline, infused with a waterproof compound, have the distinct advantage of automatically sealing small accidental cuts or lacerations in the cable jacket. Plus, the flooding compound works perfectly with the Snap-N-Seal connector's O-rings to provide a reliable, environmentally sealed connection that prevents shield contamination, with no external waterproofing requirement. These low-loss cable assemblies feature a waterproof polyethylene jacket, dual shields, and connectors that are installed with a unique 360 degree radial compression system. A superior RF integrity of over -95 dB external signal rejection means that DX Engineering F6 75-ohm Coaxial Cable Assemblies are your best choice for any high performance system installation.
Not Yet Reviewed
$28.99
—
$29.99
$20.29
—
$20.99
Clearance
Scratch & Dent
Phonema Miranda S Speakers
Phonema Miranda S Speakers are designed to deliver high-quality audio with special attention to the intelligibility of SSB signals. The high-quality wide range driver is specifically positioned into a custom designed medium density fiber cabinet which is lined internally with a variety of specially selected acoustical foam materials. The resulting sound of Miranda S is clear and sharp, with a frequency response that makes it easy to understand both voice and CW signals. Bass is present and well controlled when listening to broadcast signals. The midrange curve suits voice frequencies so that they stand out above the QRM, all with the warmth of a hand-crafted wooden speaker that reduces listener fatigue. The Miranda S is a gorgeous looking and great sounding speaker that is perfect for many new and old transceivers. This 8-ohm speaker is a convenient size that matches the listed rigs, but it will work for virtually any radio. The rich and articulate sound is perfect for listening to your transceiver or receiver. Miranda S Speakers offer these features: * Speaker Cabinet Material: MDF (medium density wood fiber) * Internal Materials: Acoustic Foam AG150 and Basotect * Pull-out Bail under the front to adjust height and angle to match radio * Power Handling: 10 w * Impedance: 8 ohms * Frequency response: 80 - 18,000 Hz * Sensitivity: 83 dB * Driver protection: IP64 * Input, rear panel: Mono 3.5mm jack * Dimensions (WHD): 6.02 x 3.98 x 10.04 in. (153 x 101 x 255 mm) * Weight: 3.48 lbs. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Phonema has gained an excellent reputation for quality and value. Order Phonema Speakers from DX Engineering and discover the difference a quality speaker can make!
( 7 )
$241.99
$217.79
Clearance
Open Box
4O3A A50 Antenna/Load Switches
4O3A A50 Antenna/Load Switches serve as 50-ohm loads for open ports on the HFC4500 combiner or other multiplexer, preventing tuning degradation. Applying 12V power connects the input to the combiner's output, linking it to the corresponding combiner or filter. A typical setup switches a filter or a combiner to a monoband antenna. When the A50 is not powered, the switch defaults to a 50-ohm termination for the input and the antenna output is open. NOTE: The A50 is NOT an A/B switch. The manufacturer's label of "A/B Switch" is a product grouping, NOT an indication of the function of this product. The LOAD resistor is internal, so one of three connectors is unnecessary, which leaves an open hole in the chassis, a "normal feature" of the A50.
Not Yet Reviewed
$181.99
$118.29
Clearance
MFJ-392C Radio Communication Headphones
MFJ-392C Radio Communication Headphones are the ideal choice for Amateur Radio enthusiasts and shortwave radio listening, offering versatility across all modes including SSB, FM, AM, data, and CW. What sets it apart is its commitment to comfort, featuring a superbly padded headband and plush ear cushions that make extended listening sessions a pleasure. The headband is adjustable to accommodate various head sizes and the earpieces can be freely adjusted on three axis to provide a custom fit that is so comfortable, you'll practically forget you're wearing them while you explore radio stations from around the globe. The high-performance driver unit within these headphones ensures that the sound quality is truly exceptional, with signals coming through crystal clear. It comes equipped with a 3.5mm stereo plug and includes a free 1/4 inch stereo adaptor for added convenience. With a generous 9 foot cord, you have the freedom to move around while enjoying your favorite radio broadcasts. Plus, it's incredibly lightweight, weighing in at just 8 ounces, so you can wear it for extended periods without any discomfort. In terms of technical specifications, the MFJ-392C can handle 400mW of power and offers a frequency response spanning from 20 to 20,000Hz. Its impedance is 16Ω ±10%, and its sensitivity is an impressive 106±3dB at 1 kHz. Whether you're an avid Amateur Radio operator or a dedicated shortwave radio listener, these headphones provide the comfort and performance you need to fully immerse yourself in the world of radio communications.
( 17 )
$59.95
$47.96
Clearance
Open Box
Kenwood Base Station Speakers
Listening to any transceiver is a joy with Kenwood Base Station Speakers. Designed to match Kenwood transceivers, these speakers are great for use on many transceivers and other types of communication equipment. Top-quality base station speakers improve intelligibility and reduce listening fatigue. External speaker offer great sound and special features to enhance your station. Efficient and enjoyable communications are yours with the legendary sound of Kenwood Base Station Speakers, available from DX Engineering.
( 34 )
$121.99
$109.79
Clearance
Open Box
Alpha Delta F Connector Coaxial Cable Surge Protectors
Alpha Delta F Connector Coaxial Surge Protectors are rated for 200 or 2,000 watts at frequencies up to 3 GHz. They are not DC-blocked, so they will pass control and power voltages in applications requiring the coaxial cable to carry both RF and DC voltage. They can be easily mounted for the most effective grounding with their 1/4-20 in. stud in a single hole, or as a bulkhead through the grounding panel. In a study under the auspices of the U.S. Dept. of Energy, utilizing the satellite FORTE launched in 1997 carrying VHF lightning discharge sensors, it was determined that there can be damaging lightning energy emissions throughout the 30 through 300 MHz VHF spectrum. Before FORTE, it was thought that most lightning energy emissions were primarily in the VLF range. Therefore, the damage threat can be anywhere from VLF through VHF. Through the careful design of the Alpha Delta Arc-Plug® gas tube module and precision, constant impedance through-line allowing proper firing characteristics, these devices are designed to provide effective protection throughout this entire spectrum. Other surge protector designs may only utilize simple VLF filters with no gas tube backup. Additional features include: * Excellent broadband performance from DC through 3 GHz, compared to the narrow-band DC-blocked or stub designs. Typical dB loss: 0.1@ 1 GHz; 0.2@ 2 GHz; and 0.5@ 3 GHz. * Innovative impedance-compensated, through-line cavity design allows control voltages to pass through the devices, instead of the "wire-around" requirement of DC-blocked designs. This design allows "in-circuit" cable sweeps. * Innovative, fast-acting gas tube replaceable Arc-Plug® module can be removed and replaced in the field in about one minute with no tools required, and without having to remove the protector from the circuit. The "O" ring sealed knurled knob does the trick! * The Arc-Plug® module and connectors are "O" ring sealed for complete weatherproofing. * Effective performance. Due to the carefully designed reactance-compensated, through-line cavity and Arc-Plug® module placement, customer and government test approvals show that this design is as good as, or better than, DC-blocked designs. Lightning surges do lots of damage annually. Protect your equipment from surges with Alpha Delta F Connector Coaxial Surge Protectors from DX Engineering!
( 3 )
$79.99
$75.99
Clearance
Open Box
Antennas-Amplifiers LPF30 HF Low Pass Filters
Product Line Title: Antennas-Amplifiers LPF30 HF Low Pass Filters Antennas-Amplifiers LPF30 HF Low Pass Filters are designed for use with legal-limit linear amplifiers up to 2kW. They operate across a passband frequency range of 1.5–29.7MHz with a low insertion loss of 0.07dB, maintaining signal integrity while suppressing harmonic frequencies generated by the amplifier. These filters feature a 50-ohm nominal impedance and come equipped with SO-239 coaxial connectors. Precision-tuned and verified using a calibrated HP8753ES network analyzer, they deliver low return loss and consistent attenuation performance. The LPF30 Low Pas Filters support flexible mounting in any position with the included 5mm mounting holes. Exceptional Performance is achieved through careful design, tuning, and component selection.
Not Yet Reviewed
$332.99
$249.74
Clearance
Open Box
ACOM 2000A Automatic HF Linear Amplifiers
ACOM 2000A Automatic HF Linear Amplifiers are the world's most advanced amplifiers designed specifically for hams. These amplifiers were the first to include fully-automatic tuning and sophisticated digital-control capabilities. ACOM's revolutionary 2000A amplifiers deliver maximum legal power in all modes and operate on all amateur HF bands 160 to 10 meters. Be sure to read the SPECIAL Note, below. These amplifiers follow your transceiver's band and frequency automatically in far less than a second. No special cables are required: Just a "dit" on CW or "AHH" on SSB is enough for instant band and band segment changes. ACOM 2000A amps break every amateur band into multiple frequency segments. The user can store up to ten (10) sets of tuning adjustments for every frequency segment - allowing individual settings for multiple antennas on each band. By completely eliminating time-consuming tune-up procedures, ACOM 2000A linear amplifiers give contesters a real edge. At the core of the ACOM 2000A is a classic HF amplifier design that employs two matched 4CX800A high-performance ceramic-metal tetrodes for maximum efficiency. ACOM uses these rigorously tested tubes with today's most advanced digital control technology to create an amplifier with outstanding performance, features and reliability. Measured third and fifth order IMD are typically 40dB and 45dB down, respectively. Typical harmonic emissions are as low as -55dBc (second) and below -70dBc (for third and above). Thus, probability of QRM, BCI or TVI is dramatically minimized. ACOM's 2000A remote diagnostic features and modular design ease fault isolation and repair. The protection system makes damaging one of these amplifiers difficult. Information on the 12 most recent protection trips is stored in an INFO BOX for remote diagnostics via phone line, PC, and Internet. Full break-in (QSK) is based on a built-in vacuum relay. Transmit/receive switching sequence is secured by a dedicated microprocessor. * Frequency Coverage: All Amateur Bands 1.8-29.7 MHz * Power Output: 1,500W PEP, 1,500W continuous carrier (the external auxiliary fan must be installed for operations of continuous carrier transmissions longer than 15 minutes * Hum and noise: Better than 35dB below rated output * Harmonics Output Suppression: Better than 50dB below rated output * Input and Output Impedance: Nominal values: 50 Ohm unbalanced output; Input circuit: broadband, VSWR less than 1.3:1, 1.8-29.7 MHz Amateur Bands (no tuning, no switching); Relay Bypass Throughput: VSWR less than 1.1:1, 1.8-29.7 MHz Amateur Bands * Automatic Tuning: Load Impedance Matching - less than 3 seconds; Band Change - less than one second; Segment Change - less than 0.2 seconds * RF Gain: 14.5dB, frequency response less than 0.5dB (50 to 60W drive power for rated output) * ALC: grid-current derived, -11V max, rear panel adjustable * Primary Power: 180-264V (200, 220 and 240V nominal taps, 10 percent tolerance), 50-60Hz, single phase, 3,500VA consumption at rated output * SPECIAL Note: Order part number AOM-2000A to wire the AC plug yourself; order part number AOM-2000A-240 for pre-wired 240 volt operation * Complies CE safety and electromagnetic compatibility requirements, as well as FCC regulations * Size: W 17.3 x 19.7 x H 7.1 in. Weight: 36 kg * Operating environments: temperature range: 0 to 50 degrees C; Humidity: up to 95 percent at 35 degrees Celsius * Altitude: up to 3,000m above sea level without output degradation Note: For additional information, please look at the files under the "Documentation" tab. Get the most advanced legal-limit HF amplifier for your shack. Order ACOM 2000A Automatic HF Linear Amplifiers from DX Engineering… today! Note: During and after your amplifier's warranty period, DX Engineering can direct you to the appropriate location for repairs for ACOM amplifiers. That facility will charge a repair fee for services outside the warranty period.
( 9 )
$7,499.99
$6,374.99
Clearance
DX Engineering Multi-Band Dipole Antennas
DX Engineering Multi-Band Dipole Antennas are designs that are rugged, yet lightweight. Using a tuner, they are usable to 30 MHz and come complete with the wire elements, ladder feedline, center T support, and end mount brackets. These antennas are built using the highest quality components. They use 14 AWG stranded-copper, PVC jacketed elements for flexibility and strength and 100 ft. of 18 AWG 300-ohm 0.88 Velocity Factor ladder lines that are UV-resistant. Stainless steel hardware is included. Often, a 4:1 balun is suggested for multi-band dipoles; however, the best balun to use for this application is a 1:1 ratio. The 1:1 baluns provide better balance, have lower loss, and are more tolerant to load impedance and balance variations than other baluns. A tuner balun is not included in the dipole antenna kits and is available separately. The dipole center T support has pre-drilled holes for the attachment of the wire elements, feedline, and support or messenger lines. The center support top hole is used for the attachment of a "messenger line" that can be strung above the antenna wire and is used to provide support for the antenna wire and feedline. The use of the messenger line, which is strongly recommended but not included, will reduce the stress on the element wires and keep the antenna from stretching over time, which will change its resonant frequency. This line can be thin Synthetic Textile rope available from DX Engineering, which has a high breaking strength. Ideally, it should attach to the same structure used for the dipole, only above it, forming at least a 30 degree angle between the dipole and the messenger line. For further information and to decide the amount of rope you will need, please read the included instructions and check your wire antenna area of construction. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you lack the room for more than one antenna or need a multiband antenna for band agility, consider one of these DX Engineering Multi-Band Dipole Antennas as an elegant and economical solution!
( 30 )
$93.99
—
$125.99
$75.19
—
$100.79
Clearance
Low Band Systems HF Transmit Band Pass Filters
NOTICE: Due to materials supply and logistical issues, resupply of Low Band Systems products will be delayed for an indefinite period. Low Band Systems HF Transmit Band Pass Filters are very high quality multi-stage devices designed to specifically limit the RF band pass to a single Amateur band. They eliminate image and harmonic RF interference issues for dedicated mono-band operations in multi-radio contesting environments. Required for use with transmit multiplexers, these passive filters provide the additional isolation needed to allow multiple transceivers to be operated on different bands simultaneously on the same antenna. Used individually on mono-band radio and antenna combinations, these filters provide the isolation required in multi-radio contest stations. Low Band Systems band pass filters are available for each of the ten HF Amateur Bands in 200, 500 and 1,500 watt models, and 2,000 watt models for the main contesting bands of 160, 80, 40, 20 ,15 and 10 meters. Their unique aluminum enclosures, some with fans, are laser cut with "Perfo-Box" on the side and their power handling and band of operation are stenciled chassis cutouts in European nomenclature, such as "3,5 MHz" for the 80 meter filter, for example. Their permanent demarcation allows immediate identification, preventing any future trouble with faded or missing printed labels. Supplied only with standard UHF Female/SO-239 connectors, these HF Transmit Band Pass Filters achieve over 60 dB of out-of-band suppression that virtually eliminates out of band noise and interfering signals. They are designed to provide a sharp roll off just outside each Amateur band; just below 3.5 MHz and just above 4.0 MHz for the 80 meter filter for example. Low Band Systems filters are the first choice of major multi-multi contest stations around the world! They provide the clear benefit of a dramatically lower noise floor for enhanced single-band weak signal reception desired for elite contest and Field Day operations. Low Band Systems Band Pass Filters are used in conjunction with their multiplexers, also known as multi-band transmit combiners. Low Band Systems Diplexers, Triplexers, Quadplexers and Pentaplexers, also available from DX Engineering, provide good levels of isolation between band ports, but band pass filters are also needed for multi- transmitter operation. This is because the multiplexer's main purpose is to balance the impedances for the multiple-transceiver/single multi-band antenna stations. They provide UHF Female/SO-239 connections for multiple 50-ohm transceivers to be connected to a single 50-ohm feedline. So, band pass filters are REQUIRED for each multiplexer band input to provide the additional isolation required to allow multiple transceiver setups to work. The transceivers for each band are connected to their associated band pass filter, and then to the multiplex device such as a triplexer, which is connected to a tri-band beam, for example. All transceivers can operate simultaneously with up to 80 dB of isolation, unhindered by the signals from the other connected radios operating on the other bands on the same antenna! Achieve the advanced operational advantages that these exceptional filters and multiplexers provide. Order Low Band Systems HF Transmit Band Pass Filters from DX Engineering! NOTE: Filters made for 160 meters are 2.0 MHz low pass models to prevent harmonics on higher bands. They do not reject frequencies below 1.8 MHz. If AM broadcast interference is a problem, an additional BCI filter should be used. After better antennas, these filters are suggested as the most important multi-radio station upgrade by top contest station builders and operators. Low Band Systems HF Transmit Band Pass Filters simply allow more contacts to be made with worldwide DX stations and DXpeditions.
( 28 )
$359.99
$233.99
Clearance
DX Engineering Bead Choke Standoff Kits
DX Engineering Bead Choke Standoff Kits bring a practical solution to a serious problem when ferrite chokes are placed directly onto the metal boom at the feedpoint of beam antennas. A number of Amateur Radio operators and antenna engineers have known for years about the superior choking function of many ferrite toroids beads placed directly on the coaxial cable, as compared to standard feedpoint baluns. A more recent revelation is that the proximity of ferrite beads on coax taped to the aluminum boom of the antenna drastically reduces their effectiveness. DX Engineering Bead Choke Standoff Kits are mounting systems, made of fiberglass or acetyl standoff rods (color varies), PVC carriers and stainless steel hardware, available in four versions. Two sizes of PVC cradle tubes handle two different types of RF bead chokes; 3/4 inch outside diameter (OD) ferrite beads on RG-400 size cable, and 1 inch OD ferrite beads on RG-213 size 0.405 in. coax cable. Each are offered with two different boom size clamps, 2 inch OD and 3 inch OD. Bead Choke Standoff Kits simply hold an RF bead choke and feedline 4 inches away from the metal beam antenna boom (or 4 inches away from the metal mast for a dipole). They maintain the optimal choking performance of ferrite beads on coax. Using DX Engineering Bead Choke Standoff Kits, ferrite bead chokes function at peak performance for these key results: • Prevent feedline radiation of RF • Preserve current balance for proper beam antenna pattern • Prevent feedline shield exterior collected noise and signals from entering the antenna and interior of the feedline, resulting in lower noise floor and enhanced reception The absolute superiority of RF chokes made of many beads on the feedline, over the traditional enclosure balun, is becoming better understood in Amateur Radio. They achieve the best possible RF isolation of the feedline from the antenna and provide completely balanced currents at the feedpoint. Plus, they provide quieter reception with reduction of common-mode noise. Keeping Bead RF Chokes away from metal preserves the optimal function of this method of antenna feedpoint current balance and isolation. This mechanical requirement is simple and practical with DX Engineering Bead Choke Standoff Kits.
( 3 )
$65.99
$52.79
Clearance
COMTEK Jerry Sevick W2FMI Series Current Baluns
COMTEK Jerry Sevick W2FMI Series Current Baluns were inspired by the writing of Jerry Sevick, as published in his book "Understanding, Building, and Using Baluns and Ununs" also available from DX Engineering. COMTEK baluns are value-engineered for maximum performance at a reasonable cost. They provide a superb, efficient transition between unbalanced coax and balanced antennas. COMTEK Baluns feature: * Jerry Sevick design with modern improvements from DX Engineering's in-depth balun research and development * Unique high-voltage compensating capacitors for unequaled SWR bandwidth * Outstanding ferrite-mix coated toroid core with special design to accommodate close coupling without excessive stress * Exceptionally high and consistent common mode impedance across the specified bandwidth, which provides isolation where it is needed most * Special wire size selection and Teflon-insulated wire sleeves provide exact impedance matching and superb insulation, unlike common Thermaleze wire * Typical insertion loss is less than 0.2 dB * Power handling on HF is 3 kW CW and 5 kW SSB on single core models, 5 kW CW and 7 kW SSB on dual core models * May be used to 54 MHz with reduced ratings * Gasketed SO-239 connectors are silver plated and have Teflon insulation * Sealed in a weatherproof 4 in. x 4 in. x 2 in. NEMA box * Stainless steel hardware Note: Polarity markings on baluns are used for matching phase on balanced antennas when stacking beams for a phased array. Also, the positive terminal should be connected to a vertical element or Inverted-L and the negative terminal goes to the radials. For most regular applications on one antenna, including beams, dipoles and most wire antennas, balun polarity doesn't matter. The best Amateur Radio baluns in the world are from DX Engineering. That includes COMTEK Jerry Sevick W2FMI Series Current Baluns!
( 10 )
$104.99
$68.24