Availability
DX Engineering AFHD-4 AM/FM/HD Antennas
DX Engineering AFHD-4® AM/FM/HD Antennas are designed for easy outdoor or attic installation. With rugged pro-quality construction, these low profile omni-directional antennas will bring out the best performance from any receiver. They deliver best-in-class AM/FM and HD radio reception over a single RG-6 cable! DX Engineering AFHD-4® antenna features: * AM and FM broadcast reception, analog and digital * Easy to install; mast and wall-mount options included * Omni-Directional antenna receives signals from 360 degrees * Requires single RG-6 coaxial cable (not included) * Band separator for optimal performance * Antenna Length: 49.00 in. (not including the base) Note: For additional product information, please look at the files under the "Documentation" tab. Many audiophiles use high-end, classic and vintage receivers. HD receiver listeners use the latest in digital technology. Why not have a professional quality antenna that will satisfy both kinds of listening? Old receiver or new, these DX Engineering AFHD-4® AM/FM/HD Antennas deliver the best broadcast radio reception!
( 11 )
$165.99
On Sale
DX Engineering IC-7300 Power Up Gear Combo
Take your Amateur Radio experience to the next level with the DX Engineering IC-7300 Power Up Gear Combo, featuring two powerhouse components designed for performance, reliability, and convenience.
( 1 )
$1,185.90
$1,174.90
Clearance
DX Engineering Multi-Band Dipole Antennas
DX Engineering Multi-Band Dipole Antennas are designs that are rugged, yet lightweight. Using a tuner, they are usable to 30 MHz and come complete with the wire elements, ladder feedline, center T support, and end mount brackets. These antennas are built using the highest quality components. They use 14 AWG stranded-copper, PVC jacketed elements for flexibility and strength and 100 ft. of 18 AWG 300-ohm 0.88 Velocity Factor ladder lines that are UV-resistant. Stainless steel hardware is included. Often, a 4:1 balun is suggested for multi-band dipoles; however, the best balun to use for this application is a 1:1 ratio. The 1:1 baluns provide better balance, have lower loss, and are more tolerant to load impedance and balance variations than other baluns. A tuner balun is not included in the dipole antenna kits and is available separately. The dipole center T support has pre-drilled holes for the attachment of the wire elements, feedline, and support or messenger lines. The center support top hole is used for the attachment of a "messenger line" that can be strung above the antenna wire and is used to provide support for the antenna wire and feedline. The use of the messenger line, which is strongly recommended but not included, will reduce the stress on the element wires and keep the antenna from stretching over time, which will change its resonant frequency. This line can be thin Synthetic Textile rope available from DX Engineering, which has a high breaking strength. Ideally, it should attach to the same structure used for the dipole, only above it, forming at least a 30 degree angle between the dipole and the messenger line. For further information and to decide the amount of rope you will need, please read the included instructions and check your wire antenna area of construction. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you lack the room for more than one antenna or need a multiband antenna for band agility, consider one of these DX Engineering Multi-Band Dipole Antennas as an elegant and economical solution!
( 30 )
$93.99
—
$125.99
$75.19
—
$100.79
On Sale
DX Engineering Select Transceiver Packages
DX Engineering Select Transceiver Packages offer Amateur Radio enthusiasts the opportunity to purchase some of our best-selling equipment in conveniently packaged sets. These packages include a transceiver, antenna, and all necessary accessories to form a complete communications package. Certain packages also include a power supply, if required. Basically, once you get the antenna up, it's all you need to get on the air! Choose from packages that lend themselves to all-band / all-mode QRP portable use, 100-watt all-band / all-mode operations through 70cm, an SDR touchscreen 160-6 meter rig that is great for DX and contesting, a compact, ultra-portable, 100-watt all-band / all-mode compact station, or even a compact 50W 1.25 or 2 meter station. When you want a station that includes popular and easy to use components, consider one of these DX Engineering Select Station Packages! Look carefully at the photos for each package and be sure to click on the Kit/Combo Contents tab for more detailed information about every item contained in a package. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE® Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
( 7 )
$2,117.54
—
$2,826.76
$1,756.54
—
$2,815.76
On Sale
DX Engineering Switch Pad 8 Transceiver Memory Keypad
DX Engineering Switch Pad 8 Transceiver Memory Keypad is an eight-button external keypad inspired by DM2RM for use with specific Icom and Kenwood transceivers. It provides a method of selecting voice and CW keying memories without the need to access the keyer menu on the transceiver's main touch screen. This prevents the reduction of the functionality of the main screen during contesting. It also enhances transceiver keyer memory access without the need to integrate the radio with a computer program. For these Kenwood transceivers, in addition to memory keyer access, any of 99 different functions may be programmed to respond to one of the eight buttons on this external keypad, as described in the transceiver manuals. This convenient keypad connects to the appropriately named 3.5mm port only on these transceivers: Icom IC-705, IC-7610, IC-7850 and IC-7851 Kenwood TS-890S and TS-990S See your transceiver manual for functional details of using an external keypad. This item will operate as described. The Switch Pad 8 has an internal jumper to select for use with either Icom or Kenwood. Here is another quality accessory designed for specific high-quality transceivers; the DX Engineering Switch Pad 8 Transceiver Memory Keypad is ready to enhance your transceiver's operations. A complete set of replacement buttons is available. Order part number: DXE-SWP8-BTN
( 21 )
$96.99
$86.99
Clearance
DX Engineering Feedpoint Connectors
DX Engineering Feedpoint Connectors provide a direct transition from coaxial cable to feedpoint for Yagi, Loop Fed Arrays (LFA), Rotatable Dipoles and other antennas that do not have a coaxial connector. Three Feedpoint Connector types are available; SO-239 UHF Female, Type-N Female and 7-16 DIN Female. Each Feedpoint Connector (FPC) features silver-soldered solid tinned-copper 12 AWG wire leads to the connector, which is epoxy potted into a plastic housing, 1.573 inch square and 0.787 inch deep, for a weather-sealed direct feedpoint connection. Of course, additional weatherproofing should be applied to the male to female connector junction, as is typically suggested. DX Engineering Feedpoint Connectors' two wire leads are about 4 in. each, for connection to balanced driven elements of beams and rotatable dipoles on which a coaxial connector does not exist. A longer length of wire is easily soldered to these tinned wires, if required, but increasing connection spacing drives up feedpoint impedance and increases the possibility of mismatch. FPCs are ideal for antennas, especially phased antenna pairs or multiples, on which a coaxial cable ferrite RF bead choke is required at the feedpoint, in place of a traditional enclosed balun. DXE-FPC units do not have mounting clamps, straps or holes. They are intended to be supported by the coax cable attachment to the boom or mast and by the connections to the antenna. An appropriate center insulator kit, such as the DXE-UWA-KIT and coaxial cable strain relief, DXE-CSR213-1, can accommodate the use of Feedpoint Connectors SO-239 UHF Female, Type-N and 7-16DIN for specialized and high power wire antennas, also accommodating a ferrite RF Bead Choke on the RG-213U size coax cable, 0.405 in. diameter.
( 8 )
$46.99
$37.59
DX Engineering Yagi Mechanical® Antenna Design Software Download
Developed specifically for the antenna building enthusiast, DX Engineering Yagi Mechanical® Antenna Design Software has been rebuilt from the ground up to display a greater range of accurate data while streamlining the design and planning of your beam antenna project. This completely new version provides greater flexibility in tubing types, simplified data entry, and automated measurement conversions. YM® now delivers 3D views, real-world mechanical strength and wind load calculations, as well as material costing and DX Engineering material links. Click the product listing to read the Overview, where a web link provides a free trial version download. Unlock the Full Version with the purchase of a Yagi Mechanical® software license here, which is delivered by e-mail, typically within two business days.
( 1 )
$69.99
On Sale
DX Engineering Getting Started Mobile Radio Packages
Congratulations! Your Amateur Radio license from the FCC has arrived! But what do you do now to get on the air from your vehicle? DX Engineering has the answer with our DX Engineering Getting Started Mobile Radio Packages for new hams. Get started with Alinco, Icom, Kenwood or Yaesu mobile transceivers and Diamond Antenna and Comet brand antenna accessories. These mobile radio packages include everything you need to get on the air right away and for the long term. This is the gear you need to go mobile on 2 meters! We've eliminated the guesswork about which parts work with each radio and matching antennas with mounts! Just order the package you want by radio and antenna mount type and we've got it all ready to go! You've got your new ham ticket, now order one of your own DX Engineering Getting Started Mobile Radio Packages and get on the air! Each starter package includes: * A great mobile transceiver * An effective, high-performance mobile antenna * A matching high-quality antenna mount to fit your vehicle… choose from either a lip mount for your hatchback, trunk or door, or a magnet mount, or a luggage rack mount When reviewing these packages, click on "More Detail…" then the "Kit/Combo Contents" tab to see detailed descriptions of each included item. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$343.93
—
$1,869.79
$338.93
—
$1,508.79
Clearance
DX Engineering Rope Hardware Kits
DX Engineering Rope Hardware Kits are exactly what you need for all kinds of antenna projects that use support rope. Designed especially for use in conjunction with Mastrant Antenna Support Rope, these rope hardware kits provide just the right size pulleys, shackles, rope clips, duplex clips, carabiners, thimbles and quick links to facilitate fast and easy rigging, raising and lowering of wire antennas and guying of vertical antennas and antenna supports. They're great for experimenters, SWLs and Radio Amateurs who need to frequently adjust or "tinker" with their antennas. When used with new wire antenna installations, these products and Mastrant Antenna Support Rope allow for easy trimming or retuning of mono and multiband dipoles, end-feds, slopers and all types of wire antennas. Just lower, trim, and raise your antenna again until it's just right. For vertical antennas and support masts, use these kits for an installation that can be adjusted and disconnected easily, without having to constantly re-tie knots and deal with tangled excess rope. These kits feature stainless steel and metal-alloy parts for excellent durability and weather resistance. They will last a very long time. Are you raising a wire or vertical antenna or mast, or are using support rope on another project where strength and convenience are equally important? Consider using Rope Hardware Kits from DX Engineering for a professional looking project that really is stronger and is SO much easier to work on!
( 33 )
$14.99
—
$65.99
$9.10
—
$36.29
On Sale
DX Engineering Handheld Transceiver Packages
DX Engineering Handheld Transceiver Packages include everything you need to get on the air quickly and start enjoying the 2 meters, 1.25 meters, or 70cm bands, whether you're a brand-new recently licensed HAM or a seasoned veteran. Get started with one of our hand-picked Alinco, ICOM, Kenwood or Yaesu portable handheld transceiver packages. These packages make it easy; we've removed the guesswork about which parts work with each radio. Each package starts with a quality handheld (HT) transceiver and paired them with quality upgrades and accessories such as antennas, batteries, chargers, headsets, or speaker-microphones. Certain packages even include RT Systems PC software to make programming your new radio easy! When reviewing these packages, click on "More Detail…" then the "Kit/Combo Contents" tab to see detailed descriptions of each included item. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
( 14 )
$236.92
—
$273.92
$216.92
—
$263.92
Clearance
DX Engineering Saddle Clamps
DX Engineering Saddle Clamps are the best designed and tested clamps you'll find anywhere! And, the selection is extensive! Designed specifically to fit and secure tubing to surfaces in antenna construction, our Saddle Clamps are built strong to prevent slippage. DX Engineering U-bolts and V-bolts are crafted from high-strength 18-8 stainless steel with enough length to attach to thick plates. Saddles are cast from high-strength 535.0 aluminum with a rippled surface for superb gripping plus superior anti-corrosion properties. Saddles are available with natural or powder coated finishes. Need to clamp steel pipe or ground rods? Choose our V-clamps with stainless steel saddles. They have serrated teeth for clamping to a pipe or rod securely. All saddle clamps include stainless steel flat washers, lock washers, and nuts. NOTE: Due to the nature of high-tolerance metals, especially stainless steel, this hardware requires the application of an anti-seize thread lubricant before assembly to prevent galling and seizing. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you need Saddle Clamps for your application, there's only one smart choice--clamp central at DX Engineering.
( 111 )
$14.99
—
$44.99
$11.24
—
$33.74
Clearance
Ham Radio T-Shirts
Ham radio enthusiasts are always on the lookout for the newest equipment to enhance their hobby. Communicating with other ham operators around the world is thrilling—especially when they make contact with a very rare remote station. These cotton T-shirts feature a large bold graphic on the back and smaller version on the front, teasing "just one more radio, I promise!" The stylish, comfortable crew neck tees are available in a variety of men's sizes.
( 5 )
$19.99
$14.50
Clearance
DX Engineering Heavy-Duty Saddle Clamps
Our tradition of continuous innovation was evident with the introduction of the DX Engineering Heavy-Duty Saddle Clamp line. DX Engineering set new standards over a decade ago with the introduction of the industry's best clamps for mounting antennas and element tubing. Featuring superior gripping power, our new Heavy-Duty Saddle Clamps are available in six different sizes, to fit tubing with Outside Diameter (OD) inch sizes of 0.75, 1.00, 1.25, 1.50, 1.75, and 2.00. Commercial and industrial engineers and installation technicians all over the world have discovered a diverse range of applications for DX Engineering Heavy Duty Saddle Clamps. DX Engineering Heavy Duty Saddle Clamps are designed to be used where maximum torque handling is required on aluminum, steel or stainless steel tubing. Conceived of by builders of large and heavy Yagi antennas and Log Periodic arrays, these clamps are made in sizes that securely fit the outside diameter of tubing for mounting to a flat plate or surface. Their wide gripping surface equals superior clamping power! Perfect for antenna construction and mounting, or wherever standard U-bolt saddle clamps and other torque-control products have proven inadequate, our Heavy Duty Saddle Clamps provide excellent grip on booms, masts and element tubing. Unlike stamped or machined-type clamps, Heavy Duty Saddle Clamps are cast from a rugged aluminum alloy that grips tubing with a special textured surface and are sized for an incredibly secure fit that resists torque, wind and weather. Heavy Duty Saddle Clamps include two cast aluminum saddles (two halves) and a stainless steel reinforcement plate for high strength and superior corrosion resistance. Due to the wide diversity of clamping applications where Heavy Duty clamps are beneficial, mounting hardware is NOT included. However, a complete line of Armor-Coated and Stainless Steel Hex Bolt Hardware Sets are available for top performance in most mounting applications. Typical Heavy Duty clamp mounting applications on a 1/4 in. plate require a minimum length bolt set, as indicated in the chart, linked in "More Detail…," and displayed in the "Required Parts" tab. For larger tubing attachment applications with ultimate gripping strength, DX Engineering Super Duty Saddle clamps are also available for 2.0, 2.5 and 3.0 in. O.D. sizes. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Plan your next project with the best clamps available... period. DX Engineering Heavy Duty Saddle Clamps are ready to provide superior performance for your antenna, mast or other tubing mounting application.
( 11 )
$14.49
$10.49
On Sale
DX Engineering Emergency Readiness Packages
DX Engineering Emergency Readiness Packages – the perfect solution for reliable communication in times of crisis. These expertly designed kits take the guesswork out of emergency preparedness, providing you with everything you need to stay connected when traditional communication methods fail. Whether you're facing a natural disaster, power outage, or system failure, GMRS radios offer a dependable means of communication, using pre-defined channels for simplicity and ease of use. No need to fiddle with complex frequencies – just turn it on and go!
Not Yet Reviewed
$843.66
$763.66
Clearance
DX Engineering Hook and Loop Cable Wraps
Ever since Velcro™ was first introduced, hook and loop fasteners have been applied to almost everything… from tennis shoes to biomedical prosthetics to spacesuits and much more. When it comes to tidying up the ham shack, nothing works better than DX Engineering Hook and Loop Cable Wraps! These hook and loop wraps cling tightly to themselves, allowing you to bundle wires and cables neatly and efficiently. Use them to keep your connecting cables organized and off the floor. Make your cable runs look professional every time! These cable wraps hold tight, yet easily unfasten with a pull from the end. Because they are hook and loop, they may be undone moved and reused time and again; saving money in the process! Available with buckles or nylon wire ties to aid installation, DX Engineering cable wraps are convenient to use and extremely durable. Get some DX Engineering Hook and Loop Cable Wraps for your station to organize your cables and keep them where you want them!
( 2 )
$7.99
—
$9.99
$5.99
—
$6.49
Clearance
DX Engineering Socket Head Bolts and Hardware Sets
DX Engineering Socket Head Bolts and Hardware Sets are available for our antenna mounting products as well as your specialized projects. Offered in stainless steel, these Allen key socket head cap screws support the extreme versatility of DX Engineering Resin Support Blocks. These 8-18 stainless steel bolt and hardware sets include two socket head bolts, two split washers, and two nuts, and two flat washers for use with the Resin Support Blocks. These bolts are not threaded for their entire length, so each set will only work for a specific range of mounting plate thickness and Resin Support Block size. NOTE: The use of anti-seize thread lubricant is REQUIRED on all stainless steel hardware BEFORE initial assembly. Our DX Engineering Resin Support Blocks are superior products that use DX Engineering Socket Head Bolts and Hardware Sets as the proper high-quality companion hardware. Order them today from DX Engineering!
Not Yet Reviewed
$8.49
$6.37
Clearance
DX Engineering Feedpoint Wire and Connector Assemblies
DX Engineering Feedpoint Wire and Connector Assemblies provide a new and unique method of feeding an antenna radiating element. A ring terminal with a 1/4 in. hole is crimped and soldered to a 12 in. long insulated 14 AWG stranded copper wire, complete with weather-protective heat shrink tubing. Then, these feed point wires are terminated to the center pin of an N-type male or UHF male PL-259 with special insulating sleeves and weather-sealing heat shrink. These assemblies are intended to be used with a double female bulkhead connector, mounted into the Radial Plate, for use on an HF vertical antenna, for example. This wire and connector combination allows for the complete weather sealing of a single wire feed point, while properly terminating the feedline shield to the radial system or ground point of the antenna system. Especially useful for phased vertical installations, the DX Engineering Feedpoint Wire and Connector Assemblies are ready for your special antenna projects!
( 5 )
$35.99
$20.24
Clearance
DX Engineering Element Clamps
DX Engineering Element Clamps, also known as band clamps, are made completely from marine-grade stainless steel; even the worm gear screw and housing. They are available with or without a 10-24 threaded stud welded to the band. The standard, non-studded Element Clamps are suitable for many projects around the home or business, in the shop or the shack, and from ship to shore. They are typically used on slit aluminum or fiberglass tubing, also available from DX Engineering, for the repair and construction of antenna elements. The studded band clamps are ideal for mechanical fastening to round or odd-shaped members. These DX Engineering Element Clamps can be used for electrical connections (including grounding) or for the mechanical assembly of components, attachment of signs, etc. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. There are sizes for each and every application. Order extras of these ALL Stainless Steel DX Engineering Element Clamps for those unexpected repairs and projects!
( 10 )
$11.29
$7.49
Clearance
DX Engineering Hex Bolt Hardware Sets
DX Engineering Hex Bolt Hardware Sets let you choose the length of the bolts you want to use for your DX Engineering Clamps. To support the extreme versatility of DX Engineering Clamps, these stainless steel bolt sets come in specially selected pairs for Super Duty Saddle Clamps, Heavy Duty Saddle Clamps and our Resin Support Blocks. Eight bolt sets are provided specifically for our Genius Clamps. One of these Hex Bolt Hardware Sets will complete your order for any DX Engineering Clamps that requires a straight hex bolt. Perfectly sized for the Super Duty and Heavy Duty Saddle Clamps, various sizes of 8-18 stainless steel hex bolt sets include two hex head bolts, two split washers, and two nuts, with four flat washers, or with two flat washers for the Resin Support Blocks. Genius Clamps Bolt Sets include 8 bolts, flat washers, split washers and nuts. Please remember that price and quantity of parts vary according to the application. Saddle Clamps are typically mounted on a customer supplied 1/4 inch plate with one of these specified DX Engineering Hex Bolt Sets. Click "More Details" and find the clamp dimensions chart linked in the Documents tab, or view the recommended or required parts listing at each clamp to find the matched bolt set of minimum usable length. Longer bolt sets may be used for special applications such as on plates of greater thickness. However, some DX Engineering Hex Bolts are not threaded for their entire length, so each set will only work for a specific range of mounting plate or tubing thickness. NOTE: The use of anti-seize thread lubricant is REQUIRED on all stainless steel hardware BEFORE initial assembly. 18-8 Stainless Steel bolts have a tightening torque specification of 132 in/lbs. Our DX Engineering Genius Clamps, Super Duty Saddle Clamps, Heavy Duty Saddle Clamps and Resin Support Blocks are superior products. Use DX Engineering Hex Bolt Hardware Sets as the proper high-quality companion hardware for your clamps. Order them today from DX Engineering!
( 6 )
$6.99
—
$14.99
$4.49
—
$10.49
Clearance
Scratch & Dent
DX Engineering Replacement TW Antenna Structures
DX Engineering Replacement TW Antenna Structures are direct-replacement structures for the top (DXE-TW-BAS-TOP) or bottom (DXE-TW-BAS-BTM) of your DX Engineering TW Adventurer, Explorer, Globetrotter or Solo Explorer compact vertical dipole antennas. No one ever wants their antennas damaged, but accidents do happen; especially with antennas as portable as these TW Series antennas. Made of high-quality black powder-coated aluminum, these replacement parts are also compatible with older TW portable or stealth antennas. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. If you have need of a replacement top or bottom section of your TW antenna, order DX Engineering Replacement TW Antenna Structures and get your TW antenna back in great shape! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
Not Yet Reviewed
$128.99
—
$139.99
$77.39
—
$83.99
Clearance
DX Engineering Face Masks
DX Engineering Face Masks are a pull-over-the head neck gaiter that can be positioned over the mouth and nose. Cover yourself and help limit dust and contamination with this very useful DX Engineering logo apparel item that works like a bandanna, without needing to be tied. Stretchy fabric - one size fit all. NOTE: This product, like any cloth covering, cannot guarantee the prevention or possibility of the spread or contraction of any virus or pathogen.
( 4 )
$6.99
$2.00
Clearance
DX Engineering Armor Coated Hex Bolt Hardware Sets
DX Engineering Armor Coated Hex Bolt Hardware Sets are offered in pairs and are intended for use with DX Engineering Super Duty Saddle Clamps or Heavy Duty Saddle Clamps on a customer supplied 1/4 in. plate. These Armor Coated Hex Bolt sets include two hex head bolts, two split washers, two nuts, and two flat washers. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Armor Coated Hex Bolt Hardware Sets are offered in pairs and are available in limited quantities until they are sold out. For all bolt sizes available including sizes not available here in armor coated bolts, see the stainless steel bolts offered. Search for DX Engineering Hex Bolt Hardware Sets.
( 1 )
$6.99
—
$11.99
$1.40
—
$4.80
Clearance
DX Engineering Vinyl End Caps
DX Engineering Vinyl End Caps are designed to fit over the ends of tubing, pipe, or coaxial cables to keep moisture out and protect your equipment. Open-ended vertical tubing can collect rainwater, which may lead to internal corrosion or even cause the tubing to burst if the water freezes. Sealing the ends with vinyl caps helps prevent these issues. These caps are also ideal for sealing booms and Yagi antenna elements. Made from durable, UV-rated material, they're built to withstand harsh weather and maintain a clean, professional appearance for years. Additionally, they're perfect for keeping SO-239, Type-N female, and SMA connectors clean and dust-free when not in use. Choose DX Engineering Vinyl End Caps to seal your tubing or coaxial cable • DXE-VC-0250 will fit an SMA female connector. • DXE-VC-0375 will fit an SMA connector. • DXE-VPC-0615 (Black or Red) fits an SO239 or Type-N Female connector Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 40 )
$8.49
—
$9.99
$5.62
—
$6.74
Clearance
DX Engineering SOTAbeams Low Pass Filter Enclosures
DX Engineering SOTAbeams Low Pass Filter Enclosures provide all of the parts to house your SOTAbeams filter boards to work with your WSPRlite Classic or Flexi. Construction of the enclosure and installation of the filter and is easy to accomplish. ------------------------------------------------------------------------------------ Please note, presently we have two enclosures due to the change made by SOTAbeams: DXE-LPFV1-2-CASE is the new enclosure that fits the newer LOWPASSKIT, LOWPASSKITHB and PCB3LPF v1.2 boards. DXE-SB-LPF-CASE is the old enclosure that fits the original SOTAbeams Low Pass Filter v1.1 boards, which we have renumbered as part SBM-LPFKITDXEPCB. Supplies of these originals are limited, and when they sell out they are discontinued. ---------------------------------------------------------------------------------- Made of aluminum for excellent shielding, the enclosure has a soft grommet to protect the SMA cable and two removable covers for the access holes to allow easy manual band switching of the filter. Here are all of the parts contained in the DX Engineering SOTAbeams Low Pass Filter Enclosure Kits: 1 - Aluminum Case - Top 1 - Aluminum Case - Bottom 4 - Phillips Head Cover Screws 4 - PCB Spacers 8 - Phillips Head Screws for PCB mounting 4 - Internal Tooth Lock Washers 1 - Soft Grommet for SMA Cable 2 - Removable Access Plugs 4 - Stick-on Rubber Feet 1 - Label
( 2 )
$32.99
—
$55.99
$14.85
—
$41.99