Availability
Clearance
DX Engineering Multi-Band Dipole Antennas
DX Engineering Multi-Band Dipole Antennas are designs that are rugged, yet lightweight. Using a tuner, they are usable to 30 MHz and come complete with the wire elements, ladder feedline, center T support, and end mount brackets. These antennas are built using the highest quality components. They use 14 AWG stranded-copper, PVC jacketed elements for flexibility and strength and 100 ft. of 18 AWG 300-ohm 0.88 Velocity Factor ladder lines that are UV-resistant. Stainless steel hardware is included. Often, a 4:1 balun is suggested for multi-band dipoles; however, the best balun to use for this application is a 1:1 ratio. The 1:1 baluns provide better balance, have lower loss, and are more tolerant to load impedance and balance variations than other baluns. A tuner balun is not included in the dipole antenna kits and is available separately. The dipole center T support has pre-drilled holes for the attachment of the wire elements, feedline, and support or messenger lines. The center support top hole is used for the attachment of a "messenger line" that can be strung above the antenna wire and is used to provide support for the antenna wire and feedline. The use of the messenger line, which is strongly recommended but not included, will reduce the stress on the element wires and keep the antenna from stretching over time, which will change its resonant frequency. This line can be thin Synthetic Textile rope available from DX Engineering, which has a high breaking strength. Ideally, it should attach to the same structure used for the dipole, only above it, forming at least a 30 degree angle between the dipole and the messenger line. For further information and to decide the amount of rope you will need, please read the included instructions and check your wire antenna area of construction. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you lack the room for more than one antenna or need a multiband antenna for band agility, consider one of these DX Engineering Multi-Band Dipole Antennas as an elegant and economical solution!
( 30 )
$93.99
—
$125.99
$75.19
—
$100.79
Clearance
DX Engineering Feedpoint Connectors
DX Engineering Feedpoint Connectors provide a direct transition from coaxial cable to feedpoint for Yagi, Loop Fed Arrays (LFA), Rotatable Dipoles and other antennas that do not have a coaxial connector. Three Feedpoint Connector types are available; SO-239 UHF Female, Type-N Female and 7-16 DIN Female. Each Feedpoint Connector (FPC) features silver-soldered solid tinned-copper 12 AWG wire leads to the connector, which is epoxy potted into a plastic housing, 1.573 inch square and 0.787 inch deep, for a weather-sealed direct feedpoint connection. Of course, additional weatherproofing should be applied to the male to female connector junction, as is typically suggested. DX Engineering Feedpoint Connectors' two wire leads are about 4 in. each, for connection to balanced driven elements of beams and rotatable dipoles on which a coaxial connector does not exist. A longer length of wire is easily soldered to these tinned wires, if required, but increasing connection spacing drives up feedpoint impedance and increases the possibility of mismatch. FPCs are ideal for antennas, especially phased antenna pairs or multiples, on which a coaxial cable ferrite RF bead choke is required at the feedpoint, in place of a traditional enclosed balun. DXE-FPC units do not have mounting clamps, straps or holes. They are intended to be supported by the coax cable attachment to the boom or mast and by the connections to the antenna. An appropriate center insulator kit, such as the DXE-UWA-KIT and coaxial cable strain relief, DXE-CSR213-1, can accommodate the use of Feedpoint Connectors SO-239 UHF Female, Type-N and 7-16DIN for specialized and high power wire antennas, also accommodating a ferrite RF Bead Choke on the RG-213U size coax cable, 0.405 in. diameter.
( 8 )
$46.99
$37.59
Clearance
DX Engineering Rope Hardware Kits
DX Engineering Rope Hardware Kits are exactly what you need for all kinds of antenna projects that use support rope. Designed especially for use in conjunction with Mastrant Antenna Support Rope, these rope hardware kits provide just the right size pulleys, shackles, rope clips, duplex clips, carabiners, thimbles and quick links to facilitate fast and easy rigging, raising and lowering of wire antennas and guying of vertical antennas and antenna supports. They're great for experimenters, SWLs and Radio Amateurs who need to frequently adjust or "tinker" with their antennas. When used with new wire antenna installations, these products and Mastrant Antenna Support Rope allow for easy trimming or retuning of mono and multiband dipoles, end-feds, slopers and all types of wire antennas. Just lower, trim, and raise your antenna again until it's just right. For vertical antennas and support masts, use these kits for an installation that can be adjusted and disconnected easily, without having to constantly re-tie knots and deal with tangled excess rope. These kits feature stainless steel and metal-alloy parts for excellent durability and weather resistance. They will last a very long time. Are you raising a wire or vertical antenna or mast, or are using support rope on another project where strength and convenience are equally important? Consider using Rope Hardware Kits from DX Engineering for a professional looking project that really is stronger and is SO much easier to work on!
( 33 )
$14.99
—
$65.99
$9.10
—
$36.29
Clearance
Scratch & Dent
Ciro Mazzoni Loop Antenna Replacement Parts
Ciro Mazzoni Loop Antenna Replacement Parts are stocked for those who need to update or reinstall their Loop Antenna by I3VHF. Parts are all original; exactly the same supplied with each model, MIDI, BABY and STEALTH models, including Actuator motors and Isolator Arms. The updated, current model ATU 2.0 replacement (MZZ-COM1001) is the same as supplied with all three new antennas. So are the Universal AC Power Supply (MZZ-COM1002) and the USB Keyboard (MZZ-COM1003). The Stainless Steel Mast Clamp and hardware (MZZ-COM1005) fit the MIDI or the BABY Loops. The MZZ-BLA1010 aluminum adapter plate is supplied with BABY Loop Tripods, available here as a replacement. Order Loop Antenna by I3VHF Replacement Parts here at DX Engineering.
( 7 )
$799.99
$439.99
—
$759.99
Clearance
MFJ Monoband Mobile HamTenna Whips
MFJ Monoband Mobile HamTenna Whips make HF mobile operating fun and easy! They're small, lightweight, efficient, and super-easy to use. Their dual feature of center and distributed loading lets you radiate efficiently... you get more power out for working DX and rag-chewing! Each antenna is ruggedly constructed from a heavy-duty, 4 ft. long, 3/8 in. diameter fiberglass rod. They also feature a nearly indestructible 0.125 in. diameter PH-17-7 stainless steel whip and chrome plated brass fittings that will give you years of dependable service. Their sleek, low-profile construction has low wind loading and their semi-rigid fiberglass eliminates the need for springs or guys. A black anti-static jacket protects the loading coil and blends in with any vehicle. The stainless steel whips are adjustable for lowest SWR and include an Allen wrench and complete tuning and matching instructions. They handle 250 watts PEP and depending on the model, they measure up to 7 ft. tall fully extended, and approximately 4 ft. tall when collapsed for easy storage. They simply screw into any 3/8 x 24 in. female mount for quick band-changing! MFJ HF Monoband HamTenna whips are available for 10, 15, 17, 20, 30, 40, and 75 meters. Think about the durable construction, efficiency, and easy band-switching that these antennas provide, and then call DX Engineering today for one of these MFJ Monoband Mobile HamTenna Whips!
( 89 )
$29.95
$23.96
On Sale
WiMo Big Wheel Horizontal Loop Antennas
WiMo Big Wheel Horizontal Loop Antennas are VHF or UHF omni-directional, horizontally polarized antennas used for weak signal work on SSB, CW, and digital modes. They are ideal companions to directional beam antennas; by covering all directions at once, they help make sure you don't miss that rare contact that may otherwise be lost. Constructed from stainless aluminum and stainless steel hardware, featuring low loss Type-N connectors, these unique monoband antennas cover 50 to 52 MHz (1,000 watt) or 144 to 146 MHz (500 watt) or 430 to 440 MHz (200 watt) providing 3 dBd gain. Two Big Wheel antennas vertically stacked will achieve about 5 dBd gain with a monoband power divider or coaxial phasing harness that connects two same-band antennas to one coax feedline.
( 6 )
$299.99
$254.99
Clearance
COMTEK Jerry Sevick W2FMI Series Current Baluns
COMTEK Jerry Sevick W2FMI Series Current Baluns were inspired by the writing of Jerry Sevick, as published in his book "Understanding, Building, and Using Baluns and Ununs" also available from DX Engineering. COMTEK baluns are value-engineered for maximum performance at a reasonable cost. They provide a superb, efficient transition between unbalanced coax and balanced antennas. COMTEK Baluns feature: * Jerry Sevick design with modern improvements from DX Engineering's in-depth balun research and development * Unique high-voltage compensating capacitors for unequaled SWR bandwidth * Outstanding ferrite-mix coated toroid core with special design to accommodate close coupling without excessive stress * Exceptionally high and consistent common mode impedance across the specified bandwidth, which provides isolation where it is needed most * Special wire size selection and Teflon-insulated wire sleeves provide exact impedance matching and superb insulation, unlike common Thermaleze wire * Typical insertion loss is less than 0.2 dB * Power handling on HF is 3 kW CW and 5 kW SSB on single core models, 5 kW CW and 7 kW SSB on dual core models * May be used to 54 MHz with reduced ratings * Gasketed SO-239 connectors are silver plated and have Teflon insulation * Sealed in a weatherproof 4 in. x 4 in. x 2 in. NEMA box * Stainless steel hardware Note: Polarity markings on baluns are used for matching phase on balanced antennas when stacking beams for a phased array. Also, the positive terminal should be connected to a vertical element or Inverted-L and the negative terminal goes to the radials. For most regular applications on one antenna, including beams, dipoles and most wire antennas, balun polarity doesn't matter. The best Amateur Radio baluns in the world are from DX Engineering. That includes COMTEK Jerry Sevick W2FMI Series Current Baluns!
( 10 )
$104.99
$68.24
Clearance
Mastrant Antenna Support and Guy Line Ropes
Mastrant Antenna Support and Guy Line Ropes are available in several sizes and strength ratings, perfect for support of wire antennas, vertical antennas and antenna masts, as well as support of Yagi booms and elements. Mastrant ropes are of the highest quality for strength and are UV-protected for extended longevity. MASTRANT-O is a highly reflective rope (bright orange plus braided reflective tape) based on long-term proven Polyester (Dacron) product line. It is designed for maximum visibility in public places such as Field Day and POTA activities. Like all Mastrant ropes, it is UV stable and resistant to all weather conditions. It has low weight, great abrasion resistance, great durability and is nonconductive (no effect whatsoever on your antenna). Moreover, in contrast to ropes made from aramid fibers (Kevlar, Vectran, Technora, Twaron), it has knot strength about 60 %. Mastrant-P and Mastrant-R Ropes are stronger than other synthetic ropes of the same size, made from proven modern polyester. Mastrant-Q is a new rope made from a blend of polyester and polypropylene, designed specifically for guying applications. It offers an excellent performance-to-price ratio and has a knot strength of approximately 60%. It replaces Mastrant-P in diameters of 6 mm (1/4 in.) and larger. Mastrant-S is a similar polyester/polypropylene rope, distinguished by its highly reflective strands for increased visibility. Mastrant-M is their highest strength rope with the Dyneema® DM20 core, a superior synthetic rope offering high performance at an affordable price. Very high strength, negligible elongation, very low weight, and great abrasion resistance are all attributes that make Mastrant-M the best rope for guying. Larger, stronger sizes of Mastrant-M are used in Europe and other parts of the world for tower guying. Durability and safety are of prime concern to ensure that an antenna installation remains fully operational for a long time. Antennas and guy lines are exposed to changing weather conditions, mechanical strain, UV radiation, humidity, and more. These non-conductive synthetic fibers have all the necessary qualities: high strength, negligible stretch but good flexibility, long life, low moisture collection, fast drying, a minimum bending radius adding the ability to tie knots, good UV radiation resistance, weather durability and resistance to acids and alkali. Conversely, steel guying wires are heavy, difficult to work with, and their strength deteriorates with time due to corrosion and general aging. Electrical conductivity of steel guys is an undesirable feature, as they interact with the antennas and adversely modify radiation patterns. Thanks to recent developments in synthetic materials, both amateur and professional users are changing over to non-conductive guys and ropes. Mastrant offers these products for a variety of applications, from thin support lines used for wire antennas and beams, to rope guys for supporting small and portable masts and vertical antennas. When you need quality rope to install, replace, or modify your antenna systems, consider Mastrant Antenna Support and Guy Line Ropes, now available from DX Engineering.
( 186 )
$298.99
—
$851.99
$239.19
—
$681.59
On Sale
Chameleon Antenna CHA LRT 2.0 Loop Remote Tuners
Chameleon Antenna CHA LRT 2.0 Loop Remote Tuners allow for remote tuning of the CHA F-LOOP 2.0 magnetic loop antennas. This permits the antenna to be mounted up to 20 feet from the operating position, such as on a balcony or deck and enables precise tuning of the loop. The CHA LRT 2.0 replaces the manual tuning knob with a motor housing and is controlled by a wired, battery-powered control box that features fast and slow tuning buttons. The CHA LRT 2.0 is not an electronic Automatic Tuning Unit (ATU), this is an electric device for mechanically rotating the loop tuning unit capacitor in place of the standard manual tuning knob. Includes detailed instructions to allow for easy installation and operation of the Loop Remote Tuner.
Not Yet Reviewed
$350.00
$262.50
Clearance
Scratch & Dent
4O3A 8xAB Antenna Switches
4O3A 8xAB Antenna Switches integrate eight independent A/B switches into a single compact unit, enabling seamless switching between multiple antennas and radios. When paired with two 403A Antenna Genius switches (O3A-40-AG8X2 or O3A-40-AG8X2-N), it forms a powerful 8×4 antenna matrix, allowing up to eight antennas to be routed to four radios with exceptional isolation. Built with the needs of high-power stations in mind, the 8xAB Switch delivers robust performance, intuitive operation, and a clean, maintainable installation. The primary motivation behind the 8xAB switch is the integration of two Antenna Genius smart switches into an 8×4 Super Switch.
Not Yet Reviewed
$775.99
$465.59
—
$737.19
Clearance
DX Engineering Feedpoint Wire and Connector Assemblies
DX Engineering Feedpoint Wire and Connector Assemblies provide a new and unique method of feeding an antenna radiating element. A ring terminal with a 1/4 in. hole is crimped and soldered to a 12 in. long insulated 14 AWG stranded copper wire, complete with weather-protective heat shrink tubing. Then, these feed point wires are terminated to the center pin of an N-type male or UHF male PL-259 with special insulating sleeves and weather-sealing heat shrink. These assemblies are intended to be used with a double female bulkhead connector, mounted into the Radial Plate, for use on an HF vertical antenna, for example. This wire and connector combination allows for the complete weather sealing of a single wire feed point, while properly terminating the feedline shield to the radial system or ground point of the antenna system. Especially useful for phased vertical installations, the DX Engineering Feedpoint Wire and Connector Assemblies are ready for your special antenna projects!
( 5 )
$35.99
$20.24
Clearance
Scratch & Dent
DX Engineering Replacement TW Antenna Structures
DX Engineering Replacement TW Antenna Structures are direct-replacement structures for the top (DXE-TW-BAS-TOP) or bottom (DXE-TW-BAS-BTM) of your DX Engineering TW Adventurer, Explorer, Globetrotter or Solo Explorer compact vertical dipole antennas. No one ever wants their antennas damaged, but accidents do happen; especially with antennas as portable as these TW Series antennas. Made of high-quality black powder-coated aluminum, these replacement parts are also compatible with older TW portable or stealth antennas. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. If you have need of a replacement top or bottom section of your TW antenna, order DX Engineering Replacement TW Antenna Structures and get your TW antenna back in great shape! NOTE: Some older versions of the TW Antennas are not compatible with current production parts. The original manufacturer of TW Antennas had changed the design more than once and newer parts will not fit some older models. Call DX Engineering to verify if your old TW Antenna will be compatible with currently produced parts and assemblies.
Not Yet Reviewed
$128.99
—
$139.99
$77.39
—
$83.99
Clearance
Larsen Mobile Antenna Replacement Parts
Larsen Mobile Antenna Replacement Parts will help you keep your Larsen antenna in great shape. Manufactured to high Larsen standards, they are OEM-quality direct replacements. When you need a replacement part for your Larsen antenna or mount, be sure to use genuine Larsen Mobile Antenna Replacement Parts from DX Engineering!
( 25 )
$11.75
$8.22
On Sale
Kelemen Trap Dipole Antennas
Kelemen Trap Dipole Antennas are high-quality, heavy-duty pre-assembled wire antennas intended for permanent installations. They feature special traps made with of PTFE (Teflon®) insulated coax for high Q and low losses, offer high performance multi-band operations—and are excellent shortened antennas where there's not enough space for a full-size dipole. Kelemen Trap Dipole Antennas include a series of monoband models, as well as a series of multi-band models that cover an extensive combination of HF bands from 160m through 10 meters. Specific models handle either 400 watts, 1,000 watts or 2,000 watts PEP SSB and CW at resonance. Kelemen Antennas are fully temperature-resistant and weather-proof, and are manufactured from high-quality materials. Balun cases are constructed of transparent, weather-proof polycarbonate with a bottom-mounted SO-239 (UHF female) connector. Hardware and clamps are all stainless steel. Each antenna is completely assembled with the balun, clear PVC-insulated stranded copper wire, stainless wire clamps and egg insulators, ready for operation. Just add rope and coax to complete your Kelemen wire antenna installation. Kelemen Trap Dipole Antennas may be mounted horizontally or in an Inverted-Vee configuration with a central support required. Many Kelemen Antennas are perfect for portable operations because of their low weight. Their coaxial traps are much lighter than conventional traps, making it easier to keep the antenna at an effective height. In many cases they can be easily supported by a single fiberglass pole. For base operations, these antennas should be placed high, in an unobstructed location well away from buildings to limit shifting of resonant frequencies. Kelemen Antennas are often the best possible antenna choice for full-time base operations, offering the advantages of specialized multi-band coverage that perfectly complements the other antennas of the station. Order Kelemen Antennas in North America exclusively from DX Engineering.
( 30 )
$199.99
—
$309.99
$159.99
—
$247.99
Clearance
DX Engineering Receive Filters
DX Engineering Receive Filters are available individually for use in the NCC-2, RPA-2, RTR-2 or DMC-2 with adapter boards. These filters are also available in sets with mounting fixtures for use in the NCC-1. DX Engineering Receive Filters are numbered for the key Amateur Band on which they function. The Band Pass filter models pass RF only on the numbered band, the High Pass models function on that band and all device frequencies above, and the Low Pass models work on that band and all device frequencies below. Response plots for Receive Filters are conveniently listed on a single page in this product's detail web page tab labeled "Charts and Guides". Some users will want to use a pair of these filters with two of the required DXE-RXFL-1 Filter Adapter Boards in their NCC-2. Each individual filter used requires a DXE-RXFL-1 Single Filter Adapter Board to convert them for installation in DX Engineering device models DXE-NCC-2, DXE-RPA-2, DXE-RTR-2 or DXE-DMC-2. All of the RXFL filters are still available in paired sets including two filters and one filter mounting fixture for owners of the legacy NCC-1 unit. See the Receive Filter Sets in combo packages by entering NCC-1 into the search box above.
( 1 )
$47.99
—
$59.99
$35.99
—
$37.49
On Sale
WiMo Portable Mast Guy Rings
WiMo Portable Mast Guy Rings are sized for WiMo metric telescoping masts. They're made of fiberglass reinforced plastic, each with three guying thimbles for secure rope attachment without binding or cutting. These guying rings anchor themselves at the mast clamp while allowing the mast to rotate even when anchored with guy ropes. Order the size needed for your application.
( 1 )
$25.99
$19.49
Clearance
DX Engineering Active Receive Vertical Replacement Tubing
DX Engineering Active Receive Vertical Replacement Tubing, model DXE-ARAV-A, is provided for those who might need to replace damaged or lost aluminum tubing for their current model DXE-ARAV4 series Active Receive Vertical antenna. This is NOT the Retrofit Kit. For the conversion of older Active Receive Verticals, see the DXE-ARAV-R which includes a new mounting plate and tubing element. This DXE-ARAV-A kit contains the three 36 in. aluminum sections, 1/4, 3/8 and 1/2 inch, as well as a complete set of new stainless steel element hardware. The required Allen wrenches are also included. The assembled length of this replacement element is 8 feet 6 inches, the same as the original. Refer to the original manual for the DXE-ARAV4-1P, -2P, -4P and -8P for assembly details. The manual is linked at the documentation section at the parts detail web pages.
Not Yet Reviewed
$79.99
$55.99
Clearance
DX Engineering Bead Choke Standoff Kits
DX Engineering Bead Choke Standoff Kits bring a practical solution to a serious problem when ferrite chokes are placed directly onto the metal boom at the feedpoint of beam antennas. A number of Amateur Radio operators and antenna engineers have known for years about the superior choking function of many ferrite toroids beads placed directly on the coaxial cable, as compared to standard feedpoint baluns. A more recent revelation is that the proximity of ferrite beads on coax taped to the aluminum boom of the antenna drastically reduces their effectiveness. DX Engineering Bead Choke Standoff Kits are mounting systems, made of fiberglass or acetyl standoff rods (color varies), PVC carriers and stainless steel hardware, available in four versions. Two sizes of PVC cradle tubes handle two different types of RF bead chokes; 3/4 inch outside diameter (OD) ferrite beads on RG-400 size cable, and 1 inch OD ferrite beads on RG-213 size 0.405 in. coax cable. Each are offered with two different boom size clamps, 2 inch OD and 3 inch OD. Bead Choke Standoff Kits simply hold an RF bead choke and feedline 4 inches away from the metal beam antenna boom (or 4 inches away from the metal mast for a dipole). They maintain the optimal choking performance of ferrite beads on coax. Using DX Engineering Bead Choke Standoff Kits, ferrite bead chokes function at peak performance for these key results: • Prevent feedline radiation of RF • Preserve current balance for proper beam antenna pattern • Prevent feedline shield exterior collected noise and signals from entering the antenna and interior of the feedline, resulting in lower noise floor and enhanced reception The absolute superiority of RF chokes made of many beads on the feedline, over the traditional enclosure balun, is becoming better understood in Amateur Radio. They achieve the best possible RF isolation of the feedline from the antenna and provide completely balanced currents at the feedpoint. Plus, they provide quieter reception with reduction of common-mode noise. Keeping Bead RF Chokes away from metal preserves the optimal function of this method of antenna feedpoint current balance and isolation. This mechanical requirement is simple and practical with DX Engineering Bead Choke Standoff Kits.
( 3 )
$65.99
$52.79
Clearance
COMTEK Stack 3 Yagi Switch Control Consoles
COMTEK Stack 3 Yagi Switch Control Consoles are available as replacements for Stack 3 Yagi Systems. When connected to the Stack 3 Switch Relay Unit, these control consoles allow you to select one antenna, all antennas, or any combination of two antennas. Indicator lights for each antenna tell you at a quick glance which antennas are selected. Choose either 115 V AC or 12 V DC control console operation. Keep using your Yagis together! Order COMTEK Stack 3 Yagi Switch Control Consoles from DX Engineering!
Not Yet Reviewed
$124.99
—
$125.99
$56.25
—
$63.00
Clearance
Open Box
Diex Antennas Two-Band Trap Shortened Rigid Rotatable Dipoles
Diex Antennas Two-Band Trap Shortened Rigid Rotatable Dipoles offer high performance multi-band HF operations, and they are an excellent choice where there's not enough space for a full-size dipole or Yagi. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these unique multi-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. DIEX Antennas Two-Band Trap Shortened Rigid Rotatable Dipoles power handling is 1500W PEP SSB, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that a directional HF antenna should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 2 )
$295.99
$236.79
Clearance
COMTEK Stack 2 Yagi Switch Control Consoles
COMTEK Stack 2 Yagi Switch Control Consoles are designed for use with newer or older COMTEK Stack 2 systems. These are the control consoles, only. They include a 2.1mm power cord and operate on 12V DC. Station power, if used, must be 12V DC at 1A minimum (fused). A 3-conductor control line between the control console and relay unit is required. Whether you are replacing a damaged console or building a new system from parts, these COMTEK Stack 2 Yagi Switch Control Consoles from DX Engineering are what your stacking system needs!
Not Yet Reviewed
$124.99
$50.00
Clearance
Hi-Z® Antennas Array Phase Combiner Units
Hi-Z® Antennas Array Phase Combiners are the relay unit at the center of a Hi-Z array, also known as a "phase controller." The sophisticated RF phasing and switching electronic devices have connections for the receive short element active vertical feedlines, delay lines, and the main feedline that goes to the station. Control cable connections to the phase combiner powers the array and steers the array pattern, and the station end connects to the directional control console.
Not Yet Reviewed
$325.00
$227.50
Clearance
Hamplus Antenna Control Switching Devices
Hamplus Antenna Control Switching Devices include automatic band data controlled remote antenna switching systems including full web remote capability without a PC. Hamplus automates HF + 50 MHz switching for 8 to 16 antennas and from 2 to 8 radios, including devices to connect multiple directional controllers to as many as 8 different antenna rotators. Band-data and frequency reading, multi-function control consoles include support for all major brand transceivers with radio specific control cables. Hamplus also offers manual multi-port to multi-radio antenna switches and a four-stack antenna switching system. Years of Amateur Radio and professional experience shows in these components for emerging and elite DXers as well as established multi-radio contest stations. Hamplus products will improve the function and performance of your station. Click on each part number for specific descriptions, specifications, more information and links to compatible or required products.
( 11 )
$52.99
—
$2,056.99
$42.39
—
$1,337.04
Clearance
Open Box
Yaesu Rotator Units
Yaesu Rotator Units are available as replacements or as stand-alone azimuth positioners for use with a third party controller. They include only the top mast bracket and hardware. Lower mast brackets are sold separately.
( 19 )
$769.99
$692.99