Filters
Antenna Phasing and Noise Cancelling
Get the most out of your receiving antennas with antenna phasing and noise cancelling products from DX Engineering. By combining multiple vertical, log periodic, or...
Get the most out of your receiving antennas with antenna phasing and noise cancelling products from DX Engineering. By combining multiple vertical, log periodic, or Yagi antennas, you can create the optimum pattern with minimum interference from unwanted signals. Our phasing controllers give you the ability to independently adjust the phase and level to achieve maximum gain. Shop our selection of DX Engineering antenna phasing and noise cancelling components and enhance your new or existing receiving antenna setup today!
Get the most out of your receiving antennas with antenna phasing and noise cancelling products from DX Engineering. By combining multiple vertical, log periodic, or Yagi antennas, you can create the optimum pattern with minimum interference from unwanted signals. Our phasing controllers give you the ability to independently adjust the phase and level to achieve maximum gain. Shop our selection of DX Engineering antenna phasing and noise cancelling components and enhance your new or existing receiving antenna setup today!
DX Engineering NCC-2 Receive Antenna Phasing Systems
Imagine adjusting the controls to knock out strong interfering stations or noise—and then being able to copy and log that weak DX station. By successfully combining the right antennas with the advanced phasing capabilities of the NCC-2, this is the operating thrill that every radio enthusiast can enjoy, again and again! DX Engineering NCC-2 Receive Antenna Phasing Systems are variable phasing controllers that combine the 300 kHz- 30MHz received signals from one transmit antenna and one receive antenna, or from two dedicated receive antennas. Combining signals from two stationary antennas physically spaced 1/10 to 1/2 wavelength apart creates an array pattern with signal peaks and dips called nulls. Adjusting the NCC-2 Phase and Balance controls have the effect of electronically rotating or steering that pattern. Steering the null direction to significantly weaken a local or distant interfering signal or noise is known as "Noise Cancelling." This "Noise Cancelling Controller" (NCC-2) can dramatically enhance the reception of weak signals from non-null directions. This "reverse-beam" capability on radio frequencies AM Broadcast through HF can provide amazing benefits for many types of AM DX and SWL receiving and ham radio operating. Work new DX, hear the weak station in casual regional conversations, snag the rare multiplier in contests and hear beyond the noise and interference in dire circumstances. DX Engineering NCC-2 Phasing Systems now feature the built-in RTR Receive-Transmit Interface relay system that expands the exciting benefits of antenna phasing for interference reduction in two ways: * First, the NCC-2 can combine signals from the HF transmit antenna and a separate receive antenna to effectively notch-out strong stations or noise. Almost any Amateur can now enjoy the benefits of antenna phasing and noise-nulling, even those with space limitations for separating the receiving and transmitting antennas. * Second, the user of any standard HF transceiver that lacks a separate receive antenna input can have enhanced reception of noise and signal nulling with the DXE-NCC-2 and two antennas. Rear panel SO-239, F and BNC connectors make the NCC-2 extremely versatile and easy to connect to almost any receiver or HF transceiver up to 200 watts. Redesigned with plug-in modular circuit board sockets, the NCC-2 includes one switched and powered internal slot and two passive internal slots per channel to accommodate these new options: * DXE-RPA-2-PM Receive Preamplifier Plug-In Modules (powered): one per channel for low-signal passive antennas with poor ground conditions * DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module (passive): Front-end protection for the NCC-2 and the receiver * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-In Module (passive): to match 75 ohm RX ANT feedlines to NCC-2 50 ohm internal impedance * NCC-2 Receive Filter Sets (passive, non-switchable): High Pass, Band Pass and Low Pass Filters for 160, 80, 40 meters typically in stock, with other band filters available individually by special order. DX Engineering NCC-2 Receive Antenna Phasing Systems offer these new additional benefits: * Multi-Color Status Indicating LEDs for Power, RTR Mode and Preamp Power CH A and CH B * New Radio Key Line Input with RX Enable Output-RTR Failsafe to prevent RF damage to NCC-2 and RX equipment * New ACC Key Line Output RCA female 'ground on transmit' pass-through for Amplifier or Accessory * New screw-on 2.1mm DC connector to prevent accidental power cable pull-out * Operates on +13.8VDC @ 2A input to power the NCC-2 and internally jumper set Bias Tee on each RX ANT ports for coax fed Active Verticals and other accessories. Offering new and experienced radio enthusiasts the next level of reception enhancements, DX Engineering model NCC-2 Receive Antenna Phasing Systems in use around the world!
( 19 )
$955.99
WiMo QRM Eliminator
The WiMo QRM Eliminator is a simple signal phasing device that can effectively reduce or remove noise interference for dramatically improved reception from 3.5 to 60 MHz. The QRM Eliminator is based on a totally innovative concept and cannot be compared to the performance of noise blanker or DSP circuits. Removing the noise before it gets to the receiver is the superior method of interference reduction. With the WiMo QRM Eliminator you can get rid of local interference almost entirely, up to an S9 level, with the likely result of completely clear reception! You don't have to understand the cause or type of interference nor do you need to know the location of its source. It doesn't matter if the interference originates from your own station or from a welding unit hundreds of feet away. The QRM Eliminator simply connects to the antenna port of transceiver and to the antenna (or amplifier input), without any radio modifications required. An additional user supplied auxiliary receiving antenna is required, such as a properly positioned 8 ft. outdoor dipole antenna or a simple 20 ft. wire in the shack, for example. This "noise sense" antenna receives mostly unwanted signal, while the transmitting antenna receives the same interference in a different phase along with the desired signal. The QRM Eliminator allows the adjustment of the amplification and phase to cancel out the unwanted signal before it reaches the receiver front end! Noise or interference nulling can provide over 45 dB of unwanted signal suppression, in many cases resulting in clear reception of the desired signal. The QRM Eliminator is built into a shielded metal enclosure, functions over the frequency range of 3.5 through 60 MHz, and has a status LED to indicate when the unit is turned on for phasing. The unit has a built-in T/R relay with PTT control via a rear panel RCA phono connector for the transceiver amplifier keying line. The QRM Eliminator automatically switches the Main antenna connection to the transceiver during transmit. Also, simply turn the unit off to bypass the phasing unit for normal reception on the Main transmit antenna. Click "More Detail" below to see additional information about this exciting device. You may not believe the power of interference phase nulling until you have experienced it for yourself. Order the WiMo QRM Eliminator exclusively in North America from DX Engineering.
( 27 )
$229.99