HAM Radio Base Transceivers

Icom IC-7300MK2 HF/50MHz Base Transceivers

Icom IC-7300MK2 HF/50MHz Base Transceivers are an advanced evolution of the original IC-7300, designed for superior performance and equipped with modern connectivity. Connectivity upgrades include a first for Icom HF transceivers: the MK2 integrates an HDMI™ output for external display of spectrum scope, waterfall, and audio. Additionally, USB Type-C™ interfaces with dual virtual COM ports and audio I/O enable simultaneous use of digital modes and logging software, while LAN ports provide simplified RS-BA1 remote control without the need for a base station PC. The IC-7300MK2 features an improved Reciprocal Mixing Dynamic Range (RMDR) of approximately 105dB at 2kHz separation and transmit phase noise reduced to –139dBc/Hz at 1kHz offset, delivering cleaner signals and enhanced adjacent-signal handling. Power efficiency is optimized with standby current reduced from 0.9A to 0.7A, minimizing heat generation for stable long-duration operation. Additional enhancements include built-in CW decoding, RX antenna IN/OUT connectors for external filters or preamps. These refinements make the IC-7300MK2 a high-performance, feature-rich solution for serious HF operators seeking cutting-edge SDR technology with robust remote and display capabilities

4.84 out of 5 stars ( 31 )

$1,499.95

Manufacturer Rebate

ICOM IC-9700 VHF/UHF/1.2 GHz Transceiver

ICOM IC-9700 VHF/UHF/1.2 GHz All-Mode Direct Sampling Transceiver features advanced technology. Built with the VHF/UHF weak signal operator in mind, the IC-9700 has an RF direct sampling receiver for the 2m and 70cm bands, and a single down conversion IF from 311 – 371MHz for the 23cm band. This combination design provides a quiet receiver using Icom's DSP technology. This is an excellent all-mode transceiver with which to cover all operating facets of the 2 meter, 70 cm and 23 cm bands! Features for the ultra-advanced Icom IC-9700 include: * Direct-Sampling SDR design * RF Output of 100 Watts on 2m (144-148 MHz), 75 Watts on 70cm (430-450 MHz) and 10 Watts on 23 cm (1240-1300 MHz) * All modes including FM, SSB, AM, CW, RTTY, Digital, D-Star Digital Voice and Digital Data * Digital Data (DD) mode provides 128 kbps data communication * D-STAR Terminal and Access Point mode (RS-MS3A/W) * Dual D-STAR receive (decodes two voice streams simultaneously) * Main and Sub RX * Full Duplex operation/ Dual Watch (no V/V or U/U Capability) * Smooth satellite operations with normal/reverse tracking and 99 satellite channels * Supports 2 wave simultaneous reception (different bands/same or different mode) * High definition Real-Time 4.3 inch TFT display * Touchscreen interface (LCD touch-screen control) * Main or Sub-Band Scope (Center/Fix mode +/-500kHz Center Mode) * Audio Scope * CW full break-in * 0.5ppm frequency stability * Voice Recording/playback function (SD Memory Card) * Ethernet Port - Internal Server for Internet remote control with optional RS-BA1 software * USB audio and control connection * DR Memories: 2,500 * Antenna connectors: 2m SO-239, 70cm Type N, 1.2 GHz Type N More information at the More Details link below. Explore new horizons and space communications with the ICOM IC-9700 VHF/UHF/1.2 GHz Transceiver.

4.73 out of 5 stars ( 127 )

$2,099.95

FlexRadio Aurora 500W HF+6M SDR Transceivers

FlexRadio AURORA™ SERIES is an all-new family of HF + 6M transceivers featuring the world's first truly integrated 500 watt SDR transmitter. The Aurora Series defines a new category in amateur radio, eliminating the traditional boundaries between transceiver, amplifier, tuner, and power supply. Designed for the modern operator, the Aurora Series delivers exceptional RF performance in a radically compact form factor—leveraging cutting-edge high-efficiency technology that produces more power with less weight, lower heat, and dramatically reduced power input requirements. Aurora Series transceivers are network ready, designed for remote access with SmartSDR clients on any Windows, macOS, iPad®, iPhone®, or Maestro™ device, in your shack, easy chair, or from virtually anywhere in the world! All four Aurora versions offer full coverage reception of 30 kHz to 54 MHz in real time for complete visibility and control across the bands. The AU-510/510M has a single SCU (Spectral Capture Unit) that digitizes the RF spectrum for signal processing and display, supporting up to 2 slice receivers and 2 simultaneous panadapters. AURORA AU-510 & AU-510M Features: • AU-510 Headless Transceiver with Integrated Remote Operation with a Maestro™, iPad®, iPhone® or PC/Laptop • AU-510M Maestro Front Panel Transceiver with 8-Inch 1920 X 1200 IPS Display and HDMI® external monitor port • 500W PEP HF, 200W 6m operation with 80% nominal efficiency • Integrated AC/DC Power Supply, 80-264VAC, 47-63Hz, PF > 0.94 • All Modes/Amateur Bands 160m-6m • Two Independent Band/Mode Receivers • Full Duplex Cross-Band Operation • One Receive Only Port • One Transverter/Exciter Port • Direct Sampling SDR 122.88Msps, 16 bit • 115 dB 2kHz RMDR • >145 dB Dynamic Range • Built in 500W Antenna Tuner • 10 MHz Reference Input • Integrated GNSS receiver with antenna maintains radio frequency with no adjustments • Optional High-performance GPSDO provides 10MHz output for external equipment The AU-520/520M features two independent SCUs, each capable of digitizing wide portions of the 30 kHz to 54 MHz spectrum simultaneously. This dual-SCU configuration allows for up to 4 slice receivers and 4 independent panadapters, making them a powerful choice for contesting, diversity reception, multi-band monitoring, and advanced digital operation. AURORA AU-520 & AU-520M FEATURES: • AU-520 Headless Transceiver with Integrated Remote Operation with a Maestro™, iPad®, iPhone® or PC/Laptop • AU-520M Maestro Front Panel Transceiver with 8-Inch 1920 X 1200 IPS Display and HDMI® external monitor port • 500W PEP HF, 200W 6m operation with 80% nominal efficiency • Integrated AC/DC Power Supply, 80-264VAC, 47-63Hz, PF > 0.94 • All Modes/Amateur Bands 160m-6m • Integrated Remote Operation with a Maestro™, iPad®, iPhone® or PC/Laptop • Four Independent Band/Mode Receivers • Full Duplex Cross-Band Operation • True Diversity Reception • Two Receive Only Ports • Two Transverter/Exciter Ports • Integrated SO2R Solution (OTRSP) Support in one radio • Contest Band Filters: >50dB Rejection band-to-band • Direct Sampling SDR 245.76Msps, 16 bit • 115 dB 2kHz RMDR • >155 dB Dynamic Range • Built in 500W Antenna Tuner • 10 MHz Reference Input • Integrated GNSS receiver with antenna maintains radio frequency with no adjustments • Optional High-performance GPSDO provides 10MHz output for external equipment

3.67 out of 5 stars ( 3 )

$6,199.00

—

$9,599.00

FlexRadio 8600 HF/6-Meter Signature Series SDR Transceivers

FlexRadio 8600 HF/6-Meter Signature Series SDR Transceivers deliver top-tier performance using direct sampling SDR technology, making it an ideal choice for serious HF and 6-meter operators. Designed for remote operation, the FLEX-8600 functions exclusively as a server, accessible via PC, laptop, Maestro, Mac*, or iOS* clients—locally or remotely. This model supports Adaptive Predistortion and includes a built-in antenna tuner, 10 MHz reference input, and an integrated GPS receiver with antenna to maintain frequency stability without manual adjustment. An optional GPSDO module is available for ultra-high frequency precision and accuracy. (sold separately) The FLEX-8600 features direct sampling SDR at 245.76 Msps with 16-bit resolution, achieving 115 dB RMDR at 2 kHz and >155 dB dynamic range. It supports 100W PEP HF-6m operation across all modes and bands, with contest-grade band filters offering >50 dB rejection for superior signal isolation. Operators can utilize four independent 14 MHz spectrum/waterfall displays and four independent band/mode receivers, offering game-changing band awareness. The transceiver supports full duplex cross-band operation on two antennas, allowing simultaneous transmit and receive on different bands without external equipment. It also enables true diversity reception to improve weak signal detection in high interference environments. Additional connectivity includes two receive-only ports and two transverter/exciter ports, which can also serve as receive antenna inputs. The FLEX-8600 provides an economical SO2R solution with OTSPR support, enabling a complete legal-limit, all-mode SO2R station when paired with the Power Genius XL LDMOS solid-state amplifier—requiring only one radio, one amp, and three cables. (amp and cable sold separately) FlexRadio's SmartSDR™ software ensures compatibility across the entire FLEX-8000 series and supports continuous software enhancements. With SmartLink™ technology, users can access their radio from anywhere using any SmartSDR-compatible client with just a login and password—even from an iPhone.

Not Yet Reviewed

$4,899.00

Manufacturer Rebate

ICOM IC-7760 HF/50MHz All Mode Base Transceivers

ICOM IC-7760 HF/50MHz All Mode Base Transceivers feature an ALL NEW innovative shack style consisting of a remote control head and separate RF deck, connected with a commercially available control (LAN) cable. This concept increases the flexibility of your station installation, making more space available on the desktop by placing the RF deck in an area closer to the antenna feed point. In addition to the direct connect feature, control head to RF deck, allows you to utilize your home network to make any tabletop your shack, and a PC is not required!

4.2 out of 5 stars ( 10 )

$6,999.95

FlexRadio 8400M HF/6-Meter Signature Series SDR Transceivers

SDR technology, paired with a high-resolution display and ergonomic controls. The FLEX-8400M combines all the capabilities of the FLEX-8400 with a stunning 8-inch 1920×1200 IPS WUXGA touchscreen and intuitive controls, delivering high-performance SDR functionality in a traditional radio interface. Unmatched band awareness comes from the integrated display, while support for external monitors at 1900×1200 resolution enhances spectral visibility. Designed with input from top contest and DX operators, the symmetrical and independent dual VFO controls are strategically placed to maximize productivity across all operating styles. Fully self-contained, the transceiver requires no PC, network, or steep learning curve—just plug in and operate. When connected to a PC, laptop, or Mac client, users can access up to two 7 MHz spectrum/waterfall displays and independent receivers, transforming how bands are viewed. Both receivers can operate simultaneously on any band and mode, with instant QSY between VFOs. Digital mode operation is streamlined—no sound cards, cables, or external boxes needed. FlexRadio's industry-leading SmartSDR™ software ensures compatibility across the entire FLEX-8000 Signature Series, enabling continuous software enhancements. With SmartLink™ technology, remote access is simple—just log in from any SmartSDR-compatible client, including an iPhone.

4.8 out of 5 stars ( 5 )

$3,649.00

Manufacturer Rebate

Icom IC-7610-32 HF Plus 50 MHz All Mode Transceivers

Icom IC-7610-32 HF Plus 50 MHz All Mode Transceivers feature internal component updates to ensure the highest performance from these true dual-receive transceivers. RF Direct Sampling takes you to the next level with advanced dynamic range performance and true dual receivers in the Icom IC-7610-32 transceiver. Whether it is poor band conditions or battling to pick out a call in a large pile-up, faint signals have always been a challenge for DXers and Contesters around the world. The difference between putting the QSO in the log or having to try another time is the combination of your skill as an operator and the capability of your receiver. One key factor, measured as RMDR, Reciprocal Mixing Dynamic Range, is the receiver's ability to pick out a faint signal in the presence of stronger, adjacent signals. The IC-7610-32 introduces dual RF direct sampling receivers that achieve 110dB RMDR, rivaling the performance of top-of-the-line transceivers. This model transmits on the Amateur bands 160 through 6 meters with 100 watts output on all modes, except 25 watts on AM, with full dual receiver coverage from 30kHz to 60MHz.

4.75 out of 5 stars ( 4 )

$3,999.95

FlexRadio 8400 Signature Series HF/6-Meter SDR Transceivers

FlexRadio 8400 Signature Series SDR Transceivers offer the latest in high-performance, direct sampling software-defined radio (SDR) technology designed for the HF and 6-meter amateur bands. Designed for hams who operate exclusively via remote access, the FLEX-8400 is engineered as a server-based SDR transceiver. It supports SmartSDR clients on Windows, Mac, iOS, and Maestro, allowing seamless control from virtually anywhere. With dual independent receivers and full duplex cross-band capability, it's ideal for DXing, contesting, and digital modes—no external sound cards or interfaces required. Using a PC, laptop, or Mac client, the FLEX-8400 supports up to two 7 MHz spectrum/waterfall displays and independent receivers, providing enhanced band visibility. Both receivers can operate simultaneously on any band and mode, with instant QSY between VFOs. Digital mode operation is streamlined—no sound cards, cables, or external interfaces required. The radio delivers advanced band awareness, low phase noise, brick wall filters, and high-quality audio performance to support a wide range of operating styles.

4.5 out of 5 stars ( 4 )

$2,499.00

FlexRadio 8600M HF/6-Meter Signature Series SDR Transceivers

FlexRadio 8600M HF/6-Meter Signature Series SDR Transceivers deliver top-tier performance through direct sampling SDR technology. Paired with a high-resolution display and ergonomic controls, the FLEX-8600M is an ideal choice for serious HF and 6-meter operators. It combines all the capabilities of the FLEX-8600 with a vibrant 8-inch 1920×1200 IPS WUXGA touchscreen and intuitive physical controls, offering high-performance SDR functionality in a traditional radio interface. Integrated display support provides unmatched band awareness, while compatibility with external monitors at 1920×1200 resolution enhances spectral visibility for advanced operations. The 8600M supports Adaptive Predistortion and includes a built-in antenna tuner, 10 MHz reference input, and an integrated GPS receiver with antenna to maintain frequency stability without manual adjustment. An optional GPSDO module is available for ultra-high frequency precision and accuracy. (sold separately) The FLEX-8600M features direct sampling SDR at 245.76 Msps with 16-bit resolution, achieving 115 dB RMDR at 2 kHz and >155 dB dynamic range. It supports 100W PEP HF-6m operation across all modes and bands, with contest-grade band filters offering >50 dB rejection for superior signal isolation. Operators can utilize four independent 14 MHz spectrum/waterfall displays and four independent band/mode receivers, offering game-changing band awareness. The transceiver supports full duplex cross-band operation on two antennas, allowing simultaneous transmit and receive on different bands without external equipment. It also enables true diversity reception to improve weak signal detection in high interference environments. Additional connectivity includes two receive-only ports and two transverter/exciter ports, which can also serve as receive antenna inputs. The FLEX-8600M provides an economical SO2R solution with OTSPR support, enabling a complete legal-limit, all-mode SO2R station when paired with the Power Genius XL LDMOS solid-state amplifier—requiring only one radio, one amp, and three cables. (amp and cable sold separately) FlexRadio's SmartSDR™ software ensures compatibility across the entire FLEX-8000 series and supports continuous software enhancements. With SmartLink™ technology, users can access their radio from anywhere using any SmartSDR-compatible client with just a login and password—even from an iPhone.

5.0 out of 5 stars ( 1 )

$5,899.00

Yaesu FT-991A HF/VHF/UHF Multi-Mode Transceivers

Yaesu FT-991A HF/VHF/UHF Multi-Mode Transceivers are the latest generation in all mode, all band MF/HF/VHF/UHF transceiver with C4FM (System Fusion) Digital capability. FT-991A transceivers include multi-mode operation on CW, AM, FM, SSB, and Digital Modes (Packet, PSK31, RTTY and C4FM), with 100 Watts of HF/50 MHz capability (50 Watts VHF/UHF). These superior-performance transceivers include a high-resolution full-color 3.5 in. TFT touch panel for exceptional operability and visibility. This "A" version of the FT-991 also includes two new exciting and useful advanced features - a Real-Time Spectrum Scope and a Multi-Color Waterfall Display. The new dynamic real-time spectrum scope gives radio operators the ability to graphically view the location of signals on the band while they listen to the received audio, allowing them to quickly move to the desired signal. The strength of signals on the band can readily be seen on the Multi-Color Waterfall Display. Chronological order color differentiation allows operators to easily recognize weak signals at a glance; signals that might otherwise be missed on the spectrum scope. FT 991As feature a rugged state-of-the-art highly balanced receiver circuit configuration. The high-speed floating point DSP from Texas Instruments used in the receiver design guarantees excellent interference rejection with actual signals under real-world conditions, not only on HF but also in the VHF and UHF bands. The 1st IF frequency incorporates selectable robust 3 kHz and 15 kHz roofing filters that effectively attenuate interfering signals. The triple conversion circuit structure allows highly flexible gain distribution at each stage. These FT-991A transceivers could not provide functions easier than at your fingertips with their 3.5 in. full color TFT display for superior operability and visibility. These rigs can be connected to a computer using a USB cable for CAT control and firmware updates, or the use of an optional SCU-17 Interface Unit to support USB Audio In/Out, TX Control (PTT, Key, and Shift). The RF amplifier in FT-991A transceivers provides a clean and solid 100 Watts of power (50 Watts VHF/UHF) and is combined with a large heat-sink and forced air automatic cooling fan to increase operating time and prevent overheating. These radios are a compact, lightweight chassis suitable for portable, mobile and base installations. Measuring 8.8 W x 3 H x 9.9 in. deep at just 9.7 pounds, this robust full-featured mobile/portable radio is ready to go when and where you are! The integral internal high-speed Automatic Antenna Tuner included in the transceiver uses an LC switching network that has a large-capacity 100 channel memory. The tuning data is automatically memorized to reduce tuning time when changing frequency. A plus/minus 0.5ppm High Resolution DDS/PLL Local Oscillator included as part of the standard radio package. Yaesu FT-991A Transceiver Specifications: * Frequency Ranges: RX 30 kHz - 56 MHz, 118 MHz - 164 MHz, 420 MHz - 470 MHz (specified performance, amateur bands only) * TX 1.8 MHz - 54 MHz, 144 MHz - 148 MHz, 430 MHz - 450 MHz (amateur bands only) * Circuit Type: Triple-Conversion Superheterodyne: SSB/CW/AM * Double-Conversion Superheterodyne: FM/C4FM * Modulation Type: A1A(CW), A3E(AM), J3E(LSB, USB), F7W(C4FM), F3E(FM), F1D(PACKET), F2D(PACKET) * Power Output: SSB/CW/FM - AM Carrier * 160 - 6 Meters: 100 - 25 W * 2 Meters/70 Centimeters: 50 - 12.5 W * Weight: 9.5 lbs. * Yaesu Warranty: 3 Years Supplied Accessories * Hand Microphone (MH-31A8J) * DC Power Cord * Spare Fuse (25A) * Operating Manual * Warranty Card Please view the Yaesu information for this product by clicking on the "Documentation" tab. When you are looking for a great Amateur Radio transceiver, consider one of these fine Yaesu FT-991A HF/VHF/UHF Multi-Mode Transceivers from DX Engineering!

4.83 out of 5 stars ( 233 )

$1,449.95

FlexRadio 8400ATU Signature Series HF/6-Meter SDR Transceivers

FlexRadio 8400ATU Signature Series SDR Transceivers offer the latest in high-performance, direct sampling software-defined radio (SDR) technology designed for the HF and 6-meter amateur bands. Designed for hams who operate exclusively via remote access, the FLEX-8400 is engineered as a server-based SDR transceiver. It supports SmartSDR clients on Windows, Mac, iOS, and Maestro, allowing seamless control from virtually anywhere. With dual independent receivers and full duplex cross-band capability, it's ideal for DXing, contesting, and digital modes—no external sound cards or interfaces required. The integrated automatic antenna tuner (ATU) is designed to match antennas with up to 3:1 SWR on 80–10 meters and up to 2.5:1 SWR on 160 and 6 meters. Using a PC, laptop, or Mac client, the FLEX-8400 supports up to two 7 MHz spectrum/waterfall displays and independent receivers, providing enhanced band visibility. Both receivers can operate simultaneously on any band and mode, with instant QSY between VFOs. Digital mode operation is streamlined—no sound cards, cables, or external interfaces required. The radio delivers advanced band awareness, low phase noise, brick wall filters, and high-quality audio performance to support a wide range of operating styles.

5.0 out of 5 stars ( 2 )

$2,849.00

On Sale

ICOM IC-718 HF All Band Transceivers

ICOM IC-718 HF All Band Transceivers make communicating with the world easy! The superior performance of these HF base transceivers allows you to make contacts over long distances--even to the other side of the world! With excellent receiver sensitivity, a wide dynamic range, high signal-to-noise ratio, and full-duty operation, the ICOM IC-718s offer the latest RF and digital technology in a compact size. Clean, clear audio is easily heard from the front-facing speaker and the IC-718s feature a minimum of switches and controls to simplify operation. Plus, a soft-touch 10-key pad allows for the direct entry of an operating frequency. These are great HF starter transceivers but they will also thrill the accomplished ham, because the IC-718s are very simple to use. The IC-718 HF All Band transceivers will definitely be the most practical DSP rigs you will ever own! They provide many useful features that you want and need--and the price isn't bad, either! Some quick specs: * 160 through 10 meter operation (60 meter channels not available) * Continuously adjustable RF power output -- 100 watts maximum to 2 watts minimum (SSB and CW modes) -- 40 watts to 2 watts (AM mode) * 30 kHz through 30 MHz general coverage receiver * 1 Hz frequency resolution * 101 memory-scan channels Other great features include: * Includes DSP noise reduction and auto notch (UT-106 module) * RF gain control * RF attenuator and preamplifier * Adjustable level noise blanker * IF shift control * Receiver Incremental Tuning (RIT) * Band stacking register * Tuning rate auto step-up function * Digital S/RF meter * VOX operation * Adjustable microphone audio compressor * Electronic CW keyer Note: For additional information, please look at the files under the "Documentation" tab. Supplied accessories include: * Hand-held microphone * DC power cable and spare fuses These little transceivers are great for portable use or as Field Day equipment. They also make great back-up transceivers for well-equipped ham shacks. New Ham or not, one of these IC-718s is a nice addition to any station. Order ICOM IC-718 HF All Band Transceivers from DX Engineering and enjoy some easy QSOs.

4.89 out of 5 stars ( 47 )

$1,099.95

$899.95

FlexRadio 8400MATU HF/6-Meter Signature Series SDR Transceivers

FlexRadio 8400MATU HF/6-Meter Signature Series SDR Transceivers feature an integrated antenna tuner (ATU), and the latest direct sampling SDR technology, paired with a high-resolution display and ergonomic controls. The FLEX-8400M combines all the capabilities of the FLEX-8400 with a stunning 8-inch 1920×1200 IPS WUXGA touchscreen and intuitive controls, delivering high-performance SDR functionality in a traditional radio interface. Unmatched band awareness comes from the integrated display, while support for external monitors at 1900×1200 resolution enhances spectral visibility. The integrated automatic antenna tuner (ATU) is designed to match antennas with up to 3:1 SWR on 80–10 meters and up to 2.5:1 SWR on 160 and 6 meters. Designed with input from top contest and DX operators, the symmetrical and independent dual VFO controls are strategically placed to maximize productivity across all operating styles. Fully self-contained, the transceiver requires no PC, network, or steep learning curve—just plug in and operate. When connected to a PC, laptop, or Mac client, users can access up to two 7 MHz spectrum/waterfall displays and independent receivers, transforming how bands are viewed. Both receivers can operate simultaneously on any band and mode, with instant QSY between VFOs. Digital mode operation is streamlined—no sound cards, cables, or external boxes needed. FlexRadio's industry-leading SmartSDR™ software ensures compatibility across the entire FLEX-8000 Signature Series, enabling continuous software enhancements. With SmartLink™ technology, remote access is simple—just log in from any SmartSDR-compatible client, including an iPhone.

5.0 out of 5 stars ( 2 )

$3,999.00

Instant Rebate

Kenwood TS-990S HF/6 Meter Base Transceivers

The ultimate Contest/DX experience is here! Kenwood's flagship HF model is equipped with the latest technology and represents an entirely new standard in HF Amateur Radio communications equipment. Kenwood TS-990S HF/6 Meter Base Transceivers come equipped with dual receivers for simultaneous reception on different bands. They also feature narrow-band roofing filters on the main receiver in a full down-conversion configuration. TS-990S features include: * Down-conversion for all amateur bands on main RX * Newly developed mixer achieves 40dBm IP3 * Narrow-band High-IP roofing filters * Comes with 0.1 ppm TCXO * DSP for main receiver, sub-receiver and band scope * Advanced AGC control * Extensive interference and noise reduction functions * Built-in automatic ATU * Dual TFT displays * USB Firmware Updates * Data mode supported by external I/O switching * Transmit and receive DSP equalizers * Two USB Ports on front panel * Voice guidance/Recording function * Remote control from your PC General details: * TX Frequency range: All Amateur bands 1.8 to 54.0 MHz * General coverage RX: Continuous 30 kHz to 60 MHz * Modes: CW, SSB, FSK, PSK, AM, FM * Stability: Plus/minus 0.1 ppm 32 degrees F to 122 F * Antenna impedance: 50 ohms * ATU range: 16.7 to 150 ohms * Line voltage: AC 120 V (60 Hz) * Power consumption: TX: 720 VA, RX: 120 VA (no signal) * Temperature range: 32 degrees F to 122 F * Dimensions in inches: 18.11 W x 6.50 H x 15.75 D Transmitter Details: * Output power: CW/SSB/FSK/PSK/FM (AM); 200 W (50 W) * Modulation SSB: Balanced, AM: Low Power, FM: Reactance * Spurious emissions: HF (Harmonics) -60 dB or less, HF (others) -50 dB or less 50 MHz -66 dB or less * Carrier suppression: -60 dB or less * Sideband suppression: -60 dB or less * Microphone impedance 600 ohms * XIT variable range: Plus/minus 9.999 kHz * Maximum frequency deviation (FM) wide: Plus/minus 5 kHz, (NFM): 2.5 kHz * Transmit frequency response: Within -6 dB (300 to 2700 Hz) Receiver: * Circuit type: Double or Triple Superheterodyne (depending on band/mode) * Sensitivity (TYP): SSB, CW, FSK, PSK (S/N 10 dB); 0.2 uV (1.705 to 24.5 MHz), 0.13 uV (24.5 to 54 MHz) * Sensitivity AM (S/N 10 dB): 2 uV (1.705 to 24.5 MHz), 1.3 uV (24.5 to 54 MHz) * Sensitivity FM (12 dB SINAD): 0.22 uV (28 to 30 MHz), 0.22 uV (50 to 54 MHz) * Image Rejection HF/(50 MHz): 70 dB/(60 dB) or less * IF Rejection Ratio 70 dB or less * SSB Selectivity 200 to 2800 Hz: 2.4 kHz or more (-6 dB), 4.4 kHz or less (-60 dB) CW, FSK, PSK Selectivity (WIDTH: 500 Hz): 500 Hz or more (-6 dB), 1.2 kHz or less (-60 dB) * AM Selectivity: 100 to 3000 Hz: 6.0 kHz or more (-6 dB), 12 kHz or less (-50 dB) * FM Selectivity: 12 kHz or more (-6 dB), 25 kHz or less (-50 dB) * XIT variable range: Plus/minus 9.999 kHz * Notch filter attenuation: 60 dB or more (Auto), 70 dB or more (Manual) * Beat cancel attenuation: 40 dB or more Note: For additional information, please look at the files under the "Documentation" tab. Get more DX! Contesters and DX Chasers will appreciate every feature on these TS-990 radios. Your time in the shack isn't unlimited. Give yourself every opportunity to make each possible contact. Couple a 200 watt transmitter and one of the most capable receivers on the planet to YOUR antenna system. Order one of your own Kenwood TS-990S HF/6 Meter Base Transceivers from DX Engineering!

5.0 out of 5 stars ( 4 )

$9,699.95

ELAD FDM-DUO SDR Transceivers

ELAD FDM-DUO SDR Transceivers are versatile SDR QRP transceivers with a 5W output that can operate independently without a PC. This compact device incorporates the latest SDR technology, featuring a fast analog-digital converter that directly samples the received HF signals into digital form. A downstream DSP module handles filtering and processing, while an ARM processor manages the control unit signals.

3.67 out of 5 stars ( 3 )

$1,329.99

—

$1,372.99

Instant Rebate

Yaesu FT-710 AESS HF/50 MHz Base/Portable Transceivers w/SP-40 Speaker

The magnificent new Yaesu FT-710 AESS HF/50 MHz SDR Transceivers represent the latest in SDR transceiver technology from Yaesu. This transceiver covers the HF Amateur Radio bands, 160 through 6 meters in a compact design that is perfect for portable operations, but equally suitable as a base station in the shack. The FT-710 AESS model includes the Acoustic Enhancement Speaker System (AESS) and features a large 4.3 inch, high-resolution TFT color multi-function touchscreen display which yields intuitive management of system settings and functions. Large control dials and the ergonomically designed layout of the front panel make the FT-710 easy to navigate. The real-time spectrum scope display adopts the FTDX series SDR 3D scope 3DSS (3 Dimensional Spectrum Stream)[RE1] to visualize changes in signal strengths within the bands.

4.94 out of 5 stars ( 84 )

$1,099.95

Instant Rebate

Yaesu FTX-1 Series HF/50/144/430MHz SDR All Mode Base/Portable Transceivers

Yaesu FTX-1 Series HF/50/144/430MHz SDR All Mode Base/Portable Transceivers provide continuous wide-range RX coverage from 30kHz through 174MHz, and from 400 through 470MHz including SWL, FM broadcast, and Air-band. TX band coverage includes HF 160 – 10M, with the addition of 6M, 2M, and 70cm. The Yaesu FTX-1 Field is perfect for portable field operation. This model features up to 10W of power output when used with an external 13.8VDC power supply. By attaching the SBR-52LI Li-ion to the rear of the Field Head, the FTX-1 provides 6W (5W for QRP) stand-alone operation on HF through V/UHF bands in all modes – SSB, CW, AM, FM and C4FM digital. 9-hour stand-alone operating time with 6W on HF bands (SSB), and 8-hour operating time with 6W on V/UHF bands (FM) are available (6-6-48 duty cycle). The FTX-1 Field Head can charge the included Li-ion battery automatically when connected to an External 13.8VDC power supply or use an optional third-party USB Type-C PD (Power Delivery) cable to recharge the battery (45W or greater/ 15V 2A).

4.58 out of 5 stars ( 19 )

$999.95

—

$1,549.95

Manufacturer Rebate

ICOM IC-7300 HF Plus 50 MHz Transceivers

ICOM IC-7300 HF Plus 50 MHz Transceivers employ a new-technology real-time touch-screen spectrum scope that leads its class in resolution, sweep speed and dynamic range. While listening to received audio, you can check the real-time spectrum scope and quickly move to another signal. When you first touch the scope screen around the intended signal, the touched part is magnified. A second touch of the scope screen changes the operating frequency and allows you to accurately tune to the desired signal. The combination of the waterfall function and the real-time spectrum scope assists in maximum receive performance of IC-7300 radios and increases QSO opportunities without missing weak signals. The waterfall function shows a change of signal strength over a period of time and allows you to find weak signals that may not be apparent on the real-time spectrum scope. The audio scope function can be used to observe various AF characteristics such as microphone compressor level, filter width, notch filter width and keying waveform in the CW mode. Either transmit or receive audio may be displayed on the FFT scope, with the waterfall function and the oscilloscope. The large 4.3 in. color TFT touch LCD offers intuitive operation. Using the software keypad of the touch screen, you can easily set various functions and edit memory contents. IC-7300 transceivers employ an RF direct-sampling system. RF signals are directly converted to digital data and processed in the FPGA (Field-Programmable Gate Array), making it possible to simplify the circuit construction. This system is a leading-edge technology; creating a new era in amateur radio. The new "IP-plus" function improves 3rd order intercept point (IP3) performance. When a weak signal is received adjacent to strong interference, the AD converter is optimized against signal distortion. IC-7300 transceivers' RMDR is improved to about 97dB (typical value) and Phase Noise characteristics are improved about 15dB (at 1 kHz frequency separation) compared to the IC-7200. The superior Phase Noise characteristics reduce noise components in both receive and transmit signals. IC-7300's have 15 discrete RF band-pass filters. The RF signal is passed through only one of the band-pass filters, while any out of range signals are rejected. High Q factor coils are used to minimize the loss in the RF band-pass filters. The built-in antenna tuner memorizes its settings based on your transmit frequency, so that it can rapidly tune when you change operating bands. The Enforced Tuning function allows a wide range of temporary antennas to be tuned. NOTE: Do not use the Enforced Tuning function except in case of an emergency. Transmitter output power may be automatically reduced. IC-7300 transceivers can store various contents into an SD card, such as received and transmitted audio, voice memories, RTTY/CW memories, RTTY decode logs and captured screen images. Updated personal and firmware data can also be stored to the SD card for easy setting. To offer superior sound quality, a new speaker unit has been incorporated and is designed into the aluminum die-cast chassis; not just squeezed in as a necessity. Other IC-7300 features include: * HM-219 hand microphone supplied * Large, effective cooling fan system * Multi-function meter * 101 memory channels (99 regular, plus 2 scan edges) * Optional RS-BA1 IP remote control software (the spectrum scope with the waterfall can be observed) * CW functions: Full break-in, CW reverse, CW auto tuning Note: For additional information, look at the files under the "Documentation" tab. The innovative features included in ICOM's IC-7300 offer tremendous advantages and represent a paradigm shift for its modest price point. ICOM says of its 7300 that "The Real HF Fun Starts Here." Order one of their ICOM IC-7300 HF Plus 50 MHz Transceivers and discover the fun to be had with leading-edge technology transceivers from DX Engineering!

4.93 out of 5 stars ( 553 )

$1,039.95

Instant Rebate

Yaesu FTDX10 Compact HF/50 MHz 100W SDR Transceivers

The exciting Yaesu FTDX10 Compact HF/50 MHz 100 W SDR Transceiver utilizes the Yaesu Hybrid SDR configuration - Narrow Band SDR and Direct Sampling SDR - like the FTDX101 series. The Narrow band SDR receiver emphasizes excellent receiver performance, while the Direct Sampling SDR provides a Digital Processing Real-Time Spectrum Scope. This stylish and well equipped model sets a new performance standard for the "affordable class" transceiver. Great for base and portable operations, the Yaesu FTDX10 is ready to order from DX Engineering. Click "More Details" for Features and Specifications Main Features of the Yaesu FTDX10 Compact HF/50 MHz 100W SDR Transceiver: - Narrow Band SDR with 3 types of roofing filters and phenomenal multi-signal receiving characteristics, as in the FTDX-101 series. The Down Conversion type receiver configuration with the first IF at 9 MHz has been adopted for the FTdx10. Excellent narrow bandwidth crystal roofing filters have the desired sharp "cliff edge" shape factor. Thanks to the Narrow Band SDR's latest circuit configuration including 500 Hz, 3 kHz and 12 kHz roofing filters and low-noise oscillator, the RMDR (Reciprocal Mixing Dynamic Range) reaches 116 dB or more, the close-in BDR (Blocking Dynamic Range) reaches 141 dB or more and 3rd IMDR (third-order Intermodulation Dynamic Range) reaches 109 dB or more in the 14 MHz band at 2 kHz separation. - 250MHz HRDDS (High Resolution Direct Digital Synthesizer) affords quiet and clear reception The local circuit of the new FTdx10 uses 250MHz HRDDS method same as the FTdx-101 series. Thanks to its characteristics that improve the C/N (carrier to noise) ratio and the careful selection of components in the design, the phase noise characteristic of the local signal achieves an excellent value of -145 dB or less in 14 MHz at 2 kHz separation. - 3DSS (3-Dimensional Spectrum Stream) on the 5-inch Full-Color TFT Display with Touch-Panel functionality The 5-inch Full-Color panel shows the 3DSS display. By touching the frequency display, the numeric keypad is displayed and the active band and frequency adjustment can be set by direct input. Frequency setting and adjustment can also be performed by turning the MAIN dial or touching the scope display. Similar to the FTdx-101 series, the MULTI display, RX operation status display, Center, FIX and Cursor modes are available. - Front Panel Designed for Superior Operating Efficiency - MPVD (Multi-Purpose VFO Outer Dial), is a large multi-purpose ring around the outside of the VFO dial that enables control of Clarifier, C/S (custom selection function) and recall of memory channels. - Remote Operation with optional LAN unit (SCU-LAN10) is possible with the optional SCU-LAN10 and SCU-LAN10 Network Remote Control Software. In addition to controlling the transceiver basic operations, the versatile scope displays enable sophisticated operations such as monitoring the band conditions on a large display at a location away from the ham shack by connection to a home LAN network. Additional features of the compact Yaesu FTDX10 include: - 15 separate band pass filters - Effective QRM rejection with the IF DSP (IF SHIFT/WIDTH, IF NOTCH DNF, DNR, CONTOUR) - High-quality and super stable final amplifier utilizing the new push-pull MOSFET RD70HUP2 - Aluminum Heat Sink with 80 mm low-noise axial flow cooling fan - High Speed Automatic Antenna Tuner with a large capacity 100-channel memory - RF & AF Transmit Monitor - Microphone Amplifier with Three-stage parametric Equalizer (SSB/ AM mode) - QMB (Quick Memory Bank) - Band Stack Function - Optional speaker – SP-30 designed for the new FTDX10 - Optional 300 Hz Plug-In Roofing Filter– XF-130CN

4.9 out of 5 stars ( 167 )

$1,499.95

On Sale

ICOM IC-7100 HF/VHF/UHF Base/Mobile Transceivers

If you haven't yet heard of the ICOM IC-7100 HF/VHF/UHF Base/Mobile Transceivers, then we can tell you that ICOM is at it again! IC-7100 transceivers introduce another amateur radio first. The radio control head features a large, multi-function, "touch screen" Dot-Matrix LCD display! This is an important feature because the controller's display not only provides information, but is also your control portal to the IC-7100's feature settings and menus. Breaking the basic rule that a radio faceplate must be vertically flat, the IC-7100's control head is sloped for the optimal viewing angle for the LCD display! The large touch screen also provides ample spacing for big fingers! ICOM even allowed plenty of room to have a large internal speaker, along with a jack for a CW key, a headphones/speaker jack, a microphone jack, and a control cable connection. IC-7100 base/mobile transceivers provide D-STAR (Digital Smart Technology for Amateur Radio) and DV (Digital Voice) mode and low speed data communication on the 2 meter and 70 centimeter bands. The D-STAR DV mode has loads of advantages over the analog FM mode: Digitally modulated clear voice; 950 bps of simultaneous data transfer; D-STAR individual calling using YOUR call sign, and access to the worldwide D-STAR repeater network linked via the Internet, just to name a few. The latest 32-bit floating point DSP (Digital Signal Processing) supports many digital processing features, such as a digital IF filter, twin PBT (Pass-Band Tuning), and manual notch filters. Of course, those high-grade digital processing features work on all ham bands from HF through the 70cm band. When considering a new all-band all-mode D-STAR equipped rig, keep these ICOM IC-7100 HF/VHF/UHF Base/Mobile Transceivers from DX Engineering in mind! Just look at these features! * All-mode operation: USB, LSB, CW, RTTY, AM, FM, WFM (Rx only) * Digital voice (DV) and data on VHF/UHF D-STAR * All bands 160 meters through 70cm (except 1.25m) * Separate control head with separation cable * Includes tactile tuning dial and direct frequency entry * 2-100W 160 through 6m, 2-50W 2m, 1-35W 70cm * Built-in SD Card Slot for voice storage and data cloning * Dual DSP chips deliver versatile digital processing performance * Built-in RTTY demodulator and decoder * Multi-function meter * SWR graphic display * DSP controller/RF speech compressor * Total of 505 memory channels * Voice recording and playback functions * ± 0.5ppm superior frequency stability * Optional RS-BA1 IP remote control software * ICOM CI-V interface capability Note: For additional information, please look at the files under the "Documentation" tab. Supplied accessories include: * Hand microphone * DC power cable * Electronic keyer plug * Spare fuses * Key plug * Accessory cable * Control head separation cable

4.85 out of 5 stars ( 95 )

$1,199.95

$838.95

Instant Rebate

Yaesu FT-710-FIELD HF/50 MHz Base/Portable Transceivers

The new Yaesu FT-710-FIELD HF/50 MHz SDR Transceivers are now available in a convenient field package that includes a handy carrying belt , but without the SP-40 speaker. The SP-40 External Speaker is available as an optional accessory if you still want to enjoy the benefit of the Acoustic Enhanced Speaker System (AESS) out in the field. FT-710-FIELD represents the latest in SDR transceiver technology from Yaesu. This transceiver covers the HF Amateur Radio bands, 160 through 6 meters in a compact design that is perfect for portable operations, but equally suitable as a base station in the shack.

4.86 out of 5 stars ( 50 )

$999.95

Instant Rebate

Kenwood TS-890S HF/50MHz Transceiver

Kenwood TS-890S HF/50MHz Transceiver: The most rewarding results often take place when faced with the harshest and most challenging conditions. HF enthusiasts know this all too well because of their love of HF. KENWOOD has the answer. Achieve results through certainty, not circumstance—delivered with impeccable receiver and audio performance. Introducing Kenwood's most advanced DSP transceiver, the TS-890S. Key features of the Kenwood TS-890S HF + 6M Transceiver: * 160-6 meters 100W All Modes * Full Down-Conversion Superheterodyne * Extra-low phase noise Local Oscillator * Built-in Roofing Filters, 15 kHz, 6 kHz, 2.7 kHz, and 500 Hz (270 Hz optional) * 7 in. TFT color display * High-speed Independent Band Scope * Animated Meter display toggles between TS-930 and TS-940 meter styles at a touch! * External display connector (DVI-I) * ANT output for external receiver * RF Attenuator (OFF/6/12/18dB) * Advanced DSP Noise Reduction function * Heavy-duty design delivers transmitter performance and endurance operation * Built-in high-speed automatic antenna tuner for rapid band changes * Encode and decode built-in for CW / PSK / RTTY * 120 channel memory * 3 PF keys (preferred function) * Screen capture * Remote operation via direct LAN connection (see KNS in owner's manual) * Multiple USB connections * KEYPAD jack (add up to 8 external PF keys) Place your order here for the Kenwood TS-890S.

4.97 out of 5 stars ( 33 )

$4,399.95

Instant Rebate

Yaesu FTDX-101MP HF+50MHz 200W Transceivers

The Yaesu FTDX-101MP HF+50MHz 200W Transceiver brings new excitement and surprising advances in a particularly attractive package. Its unique hybrid narrow-band SDR configuration achieves unsurpassed critical dual receiver performance. The Direct Sampling SDR section provides astounding visual awareness of activity across the band as well as detail around the operating frequency on each receiver. The large, precision color touch-panel display also features gorgeous dual multi-function meters, dual frequency readouts and multi-functional touch controls, plus the exclusive 3DSS - Three Dimension Spectrum Stream waterfall and panadapter scope. The entire class-leading screen of the FTDX-101MP may be displayed on a user supplied external monitor! Ergonomically arranged transceiver controls are centered about a large, tactile and weighted VFO. The Main knob is enhanced with the MPVD; Multi-Purpose VFO Outer Dial which controls the sub receiver VFO, clarifier, VC-Tune RF Preselector, VFO fine tuning and a user defined Custom Selection function. A welcome feature, each function of the identical Main (A) and Sub (B) receivers have separate independent front panel controls; AF and RF gain, Shift, Width, Notch, Contour, Digital Noise Reduction and APF. Built for the serious contester, dual LED pushbuttons comprise the Active Band Indicator for each receiver, enabling effortless and rapid independent band changes. Adjustments of mode-specific settings and levels are displayed and accomplished quickly with the press-and-turn Multi-function selector. Every important control is strategically placed and readily available for maximum flexibility and ease of operation with this remarkable transceiver. Here are some of the impressive features and specs of the amazing Yaesu FTDX-101MP: - High-Class 160 to 6 Meters 200 Watt Transceiver for all modes; SSB, AM, FM, CW, RTTY and Digital. - FPS-101 Separate External Speaker and Power Supply combination is included - Superb and astonishing close-in dynamic range performance (120 dB RDR at 2 kHz spacing, 14 MHz, 500 Hz) - Hybrid SDR technology: Direct Sampling and NBW (narrow bandwidth) SDR - 9 MHz IF roofing filter with excellent Shape Factor** - 400 MHz HRDDS (High Resolution Direct Digital Synthesizer) - Ultra-low phase noise 1st Local Oscillator - Completely independent dual receivers with general coverage receive - High-Q VC-Tune Front-End RF Preselector for maximum attenuation of -70 dB (Built-in Main and Sub Receivers) - Yaesu renowned interference reduction system with 32 bit IF DSP and digital noise reduction (DNR) and DSP Auto Notch (AN) Click 'More Detail' below to see additional information about the FTDX-101MP HF/50MHz 200W Transceivers. The 100 watt version, Yaesu FTDX-101D is also displayed in the Base Transceivers area. Many are aware that the iconic model number "101" comes from the legendary and best-selling FT-101 series produced in the 1970s. "The Legend Continues" as this HF transceiver carries the tradition of high quality known of the original 101 series. It is certain to satisfy the demands of a wide variety of Amateur Radio enthusiasts. Today, you may order the Yaesu FTDX-101MP HF/50MHz 200 Watt Transceiver from DX Engineering. **NOTE: The Yaesu FTDX-101MP has the VC Tune Preselector installed in the MAIN and SUB receivers. Roofing filters installed in the MAIN and SUB receivers are the 12 kHz, 3 kHz and 600 Hz, plus a 300 Hz is installed in only the MAIN receiver. Three optional roofing filters are available, the 300 Hz for the SUB receiver and 1.2 kHz for the MAIN and SUB receivers. Installation and calibration is done by Yaesu only with a $30 per item labor charge when options are special ordered with the transceiver. The standard model FTDX-101MP ordered on the web, and shipped from stock, cannot be internally upgraded by the user. Call DX Engineering to order your standard or custom equipped Yaesu FTDX-101MP.

4.84 out of 5 stars ( 44 )

$5,098.95

Instant Rebate

Yaesu FTDX-101D HF/50MHz 100W Transceivers

The Yaesu FTDX-101D HF/50MHz 100W Transceiver brings new excitement and surprising advances in a particularly attractive package. Its unique hybrid narrow-band SDR configuration achieves unsurpassed critical dual receiver performance. The Direct Sampling SDR section provides astounding visual awareness of activity across the band as well as detail around the operating frequency on each receiver. The large, precision color touch-panel display also features gorgeous dual multi-function meters, dual frequency readouts and multi-functional touch controls, plus the exclusive 3DSS - Three Dimension Spectrum Stream waterfall and panadapter scope. The entire class-leading screen of the FTDX-101D may be displayed on a user supplied external monitor! Ergonomically arranged transceiver controls are centered about a large, tactile and weighted VFO. The Main knob is enhanced with the MPVD; Multi-Purpose VFO Outer Dial which controls the sub receiver VFO, clarifier, VC-Tune RF Preselector**, VFO fine tuning and a user defined Custom Selection function. A welcome feature, each function of the identical Main (A) and Sub (B) receivers have separate independent front panel controls; AF and RF gain, Shift, Width, Notch, Contour, Digital Noise Reduction and APF. Built for the serious contester, dual LED pushbuttons comprise the Active Band Indicator for each receiver, enabling effortless and rapid independent band changes. Adjustments of mode-specific settings and levels are displayed and accomplished quickly with the press-and-turn Multi-function selector. Every important control is strategically placed and readily available for maximum flexibility and ease of operation with this remarkable transceiver. Some of the impressive features and specs of the Yaesu FTDX-101D include: * High-Class 160 to 6 Meters 100 Watt Transceiver for all modes; SSB, AM, FM, CW, RTTY and Digital. * Superb and astonishing close-in dynamic range performance (120 dB RDR at 2 kHz spacing, 14 MHz, 500 Hz) * Hybrid SDR technology: Direct Sampling and NBW (narrow bandwidth) SDR * 9 MHz IF Roofing Filters with excellent Shape Factor * 400 MHz HRDDS (High Resolution Direct Digital Synthesizer) *Ultra-low phase noise 1st Local Oscillator * Completely independent dual receivers with general coverage receive *High-Q VC-Tune Front-End RF Preselector for maximum attenuation of -70 dB (Built-In Main RX, Option for Sub RX) * Yaesu renowned interference reduction system with 32 bit IF DSP and digital noise reduction (DNR) and DSP Auto Notch Many are aware that the iconic model number "101" comes from the legendary and best-selling FT-101 series produced in the 1970s. "The Legend Continues" as this HF transceiver carries the tradition of high quality known of the original 101 series. It is certain to satisfy the demands of a wide variety of Amateur Radio enthusiasts. Today, you may order the Yaesu FTDX-101D HF/50MHz 100W Transceiver from DX Engineering. Click 'More Detail' below to see additional information about the FTDX-101D HF/50MHz 100W Transceivers. The 200 watt version, Yaesu FTDX-101MP is displayed separately in the Base Transceivers area. **NOTE: The Yaesu FTDX-101D has the VC Tune Preselector installed in the MAIN receiver and 12 kHz, 3 kHz and 600 Hz roofing filters installed in the MAIN and SUB receivers. A second VC Tune Preselector is optional for the SUB receiver and four optional roofing filters, 300 Hz and 1.2 kHz for the MAIN and SUB, are available only by transceiver special order. Installation and calibration are done by Yaesu only with a $30 per item labor charge when options are special ordered with the transceiver. The standard model FTDX-101D shipped from stock cannot be internally upgraded by the user. Call DX Engineering to order your standard or custom built FTDX-101D.

4.96 out of 5 stars ( 53 )

$3,749.99