Coaxial Cable Assemblies

DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coax Cable Assemblies

Our patented* revolutionary new PL-259 connector and our premium flexible DXE-8X coaxial cable were designed to make the new DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8X cable assemblies available for HF applications. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are made from our new-process low-loss, gas injected foam dielectric cable. Featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket, good for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, this is the new type of foam that cannot gather moisture and has lower loss than old RG-8X foam cables. DX Engineering RG-8X PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These new, ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849

4.97 out of 5 stars ( 512 )

$36.99

—

$125.99

DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coax Assemblies

Our patented* revolutionary new PL-259 connector and our premium, low-loss 400MAX coaxial cable are designed to make the new DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best cable assemblies available for simplex HF, VHF and UHF applications. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX DX Series low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 DX Series Coaxial Cable Assemblies are terminated at each end with our new, custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our new 400MAX DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are now available, only from DX Engineering! *U.S. Patent D745849

4.93 out of 5 stars ( 320 )

$40.99

—

$334.99

DX Engineering LMR400UF Ultra-Flex Coaxial Cable Assemblies

DX Engineering LMR400UF UltraFlex Coaxial Cable Assemblies handle twice the power at half the loss with the same bending capabilities of smaller diameter coaxial cables. UltraFlex Cable Assemblies are perfect for interconnecting high and low power HF and VHF equipment. Times Microwave LMR® 400UF UltraFlex cable has a stranded bare copper center, foam polyethylene dielectric and a pliable rubber jacket (black thermoplastic elastomer) designed for bending. DX Engineering LMR400UF UltraFlex DX Series PL-259 Coaxial Cable Assemblies are terminated at each end with our custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity checked and evaluated with extremely high voltage, then heat-shrink weather-sealed for ultimate longevity. You will not find this level of cable assembly quality anywhere else! Terminated with DX Engineering Next Generation PL-259 connectors, these cable assemblies are intended for use to 170 MHz. An exceptionally flexible, low-loss coaxial jumper for high power Amateur or commercial HF or VHF use – order DX Engineering LMR400UF UltraFlex Coaxial Cable Assemblies.

5.0 out of 5 stars ( 25 )

$52.99

—

$223.99

Comet Window Feed-Thru Jumpers

Comet Window Feed-Thru Jumpers are flexible, 50 ohm, flat feedline assemblies with SO-239 UHF female connectors at each end. They are used for routing RF through a window frame without drilling holes for the coax cable or connectors. These window-gap jumpers are almost 16 in. long and are made from copper-clad steel and PET plastic to allow for a low power transfer of RF with a nominal loss of only 0.5 dB up to 500 MHz, and they are useable up to 1300 MHz! When drilling through the wall is forbidden, or if there is no way to make a sufficient hole for your coaxial cable, then a Comet Window Feed-Thru Jumper may be the problem solver that you need! Here are the specs that will help you decide if one of these handy flat cable assemblies is right for you: * Frequency Range: DC-1300 MHz * Connectors: SO-239 * Impedance: 50 Ohm * Length: 15.75 inches * Max Power: HF 100W PEP, VHF: 60W FM, UHF 40W FM, 900 MHz–1.3 * GHz: 10W FM * SWR: Less than 1.3:1 below 500 MHz, Less than 1.5:1 above 500 MHz * Loss: DC-500 MHz = 0.5 dB, 500-900 MHz = 1.3 dB, 900-1300 MHz = 1.8 dB Whether you use one of these feed thru devices for a temporary coaxial installation or as a permanent no-hole solution, Comet Window Feed-Thru Jumpers from DX Engineering can get you on the air!

4.91 out of 5 stars ( 33 )

$64.95

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are the most flexible and lowest loss high-quality orange coaxial cable assemblies on the market. DXE-8XV cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are terminated with high quality silver plated PTFE dielectric PL-259s, and select lengths with BNC connectors for POTA and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. Color delivered can vary. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8XV is the part number for this coaxial cable sold by the foot, and it is available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 16 )

$36.99

—

$119.99

DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Cable Assemblies

Our patented* revolutionary new PL-259 connector and our premium 213U coaxial cable were designed to make the new DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Assemblies the best 213/U cable assemblies available for virtually every HF antenna application. DX Engineering 213U is a high-grade standard coaxial cable type, which features a very rugged, highly UV-resistant, non-contaminating Type II-A PVC jacket. These cable assemblies are ideal for all outdoor feedline applications, commonly used for HF and direct-bury installations. With heavy 12.5 AWG stranded copper center conductor, RG-213U PL-259 cable assemblies are perfectly suited for long cable connections to antennas from HF equipment running at very low to high power levels. Our DXE-213U cable features a solid polyethylene dielectric that cannot absorb moisture and it withstands constant movement and flexing on tower mounted rotatable and directional beam antennas. DXE-213U is used at contest station K3LR for installation at the tower top as "rotator loop" coax for HF and VHF. It has excellent shielding with minimum 96 percent coverage copper braid. Regarded in the industry as the right choice for a high quality HF feedline, our 213U Coaxial Cable is custom made for DX Engineering to provide the performance and longevity you expect. DX Engineering RG-213U PL-259 DX Series Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 213U DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our Next Generation PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849

4.97 out of 5 stars ( 182 )

$39.99

—

$339.99

DX Engineering 400MAX Type N Low-Loss 50-ohm Coax Assemblies

DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies offer the lowest possible loss at VHF and UHF frequencies. Used by communications professionals through 2,400 MHz and above, N-Type connectors have low insertion loss and maintain 50 Ohm impedance, for installations where every tenth of a dB counts! DX Engineering 400MAX coax features a tough, waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for simplex outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. B) Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. Our 400MAX DN Series cable assembly N-Type connectors feature machine crimped shields and centers, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate in-service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies are now available, only from DX Engineering!

4.88 out of 5 stars ( 33 )

$41.99

—

$182.99

DX Engineering RG-8X BNC Low-Loss 50-ohm Coax Cable Assemblies

DX Engineering RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies are very flexible low-loss, foam-dielectric, braided shield cable intended for special connections to BNC equipment. Suitable for moderate-power, base, mobile or portable applications where short runs and flexibility are key factors. NOTE: THESE ARE NOT PL-259 CABLES. These assemblies have BNC MALE connectors installed at each end of the cable, for use on specialized equipment with BNC Female connectors. Slightly larger than RG-58 cable, DX Engineering DX Engineering RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies are made from our new-process low-loss, gas injected foam dielectric cable. Featuring stranded copper center, braided copper shield and a non-contaminating Type II PVC jacket, our 8X BNC cable assemblies are intended for low to moderate power, test and mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, this is the new type of foam that cannot gather moisture and has lower loss than old RG-8X foam cables. Our RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies come complete with high-quality nickel-body Delrin-dielectric BNC male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. Their gold-plated center conductors are hand soldered and inspected. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. When you are looking for pre-assembled BNC male cable assemblies and want a high-quality, reliable product, look no farther than our own DX Engineering RG-8X BNC Low-Loss 50-ohm Coaxial Cable Assemblies!

4.97 out of 5 stars ( 38 )

$35.99

—

$65.99

DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coax Cable Assemblies

Our patented* revolutionary new PL-259 connector and our high quality, low-loss RG-8U coaxial cable were designed to make the new, extra-flexible DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8/U cable assemblies available for all HF, VHF and UHF applications. DX Engineering 8U coax features a super-flexible jacket made with UV-resistant, Type I PVC jacket which is great for all indoor and above-ground outdoor applications. With a large 11 AWG stranded copper center conductor, our 8U DX Series low-loss assemblies are well suited for short interconnections as well as long cable runs in low or high power operations. Our 8U coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has excellent shielding with minimum 95 percent coverage copper braid. DX Engineering 8U is a new-age cable that far surpasses the capabilities of the moisture collecting foam RG-8/U of 35 years ago. Now regarded in the industry as a top quality low-loss feedline, our 8U Coaxial Cable is custom made for DX Engineering to provide the highest performance with extraordinary flexibility. DX Engineering RG-8U PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 8UDX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849

4.93 out of 5 stars ( 111 )

$38.99

—

$289.99

DX Engineering RG-400 High Isolation Coaxial Cable Assemblies

DX Engineering RG-400 High Isolation Coaxial Cable Assemblies bring to your RF systems the same quality and capabilities that are demanded of military and aerospace installations. Here are few reasons why we offer these advanced RG-400 cables for your critical applications: - Extremely high isolation from noise and signals from adjacent cables - Very high power handling - 2.75 kW at 30 MHz - Stranded silver plated copper center conductor for extreme efficiency - PTFE dielectric for exceptional dimensional stability, low loss and very high power handling - Silver plated copper braided double shields for very high isolation - Tough, waterproof fluorinated ethylene propylene (FEP) - MIL-C-17 jacket DX Engineering RG-400 cable assemblies are terminated with the classic silver plated Amphenol 831SP PL-259 and UG-175 reducers or BNC Male connectors. DXE-RG400 is specifically recommended for short length cable assembly use in VHF/UHF duplex repeater applications. RG-400 may be the same size as RG-58A/U, but it is an aerospace-level performance cable with dramatically improved ratings in all categories. NOTE: RG-400 is a 0.195 in. diameter cable. RG-400 is NOT related in any way to DXE-400MAX or LMR-400 cables which are 0.405 in. diameter. Order DX Engineering RG-400 High Isolation Coaxial Cable Assemblies here.

5.0 out of 5 stars ( 16 )

$86.99

—

$127.99

Diamond Antenna Through Window/Door Cable Sets

Diamond Antenna Through Window/Door Cable Sets are great for use when a hole cannot be drilled through the wall for a coaxial feedline. Made from a flat, flexible strip that acts like coaxial cable, these RF feedline assemblies have an SO-239 at each end, so connections to a radio indoors and an antenna outdoors is a snap! Now available from DX Engineering, here are the specs on Diamond Antenna Through Window/Door Cable Sets: Frequency range: DC to 1500MHz Max Power Ratings: * HF to 50MHz: 150 W (SSB), 50 W (FM/CW), * 144MHz: 40 W (FM) * 440MHz: 30 W (FM), * 1200 MHz: 10 W (FM) Length: 19.7 in. (between connectors) Weight: 102g; 6.0 oz. Connectors: UHF Female to UHF Female VSWR: * HF up to 500MHz: Less than 1.2 * 500 to 1000MHz : Less than 1.3 * Up to 1000MHz: Less than 2.0 * 1200MHz: Less than 1.7. Impedance: 50 ohms Insertion Loss: * 144MHz: Less than 0.3dB * 440MHz: Less than 0.6dB * 1200MHz: Less than 1.6dB Here's an easy solution to get your signal through the window! Order Diamond Antenna Through Window/Door Cable Sets from DX Engineering!

4.54 out of 5 stars ( 13 )

$56.99

DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies

What if two RF devices – the radio, switch, meter, lightning protector, choke, balun or the antenna – have opposite female connectors, one type-N and the other SO-239? This dilemma is solved with the uniquely helpful DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies, the perfect alternative to questionable straight adapters. Made for any job (HF, VHF and UHF) and especially for outdoors, one top-quality silver plated Type-N male connector and one patented* Next Generation PL-259 (UHF male) connector terminates our premium, low-loss 400MAX coaxial cable to create these very useful Adapter Cable Assemblies. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications, including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX NX Series low-loss assemblies are perfectly suited for short or long cable runs and low or high-power level operations. Our 400MAX coaxial cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95-percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. Note: DXE-400MAX is not recommended for use in repeater applications, VHF/UHF duplex, or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 NX Series Coaxial Adapter Cable Assemblies are terminated at one end with the N-Type male connector and the other end with our custom-designed DX Engineering PL-259 (UHF male) connector. Both silver plated connectors feature machine-crimped shields with 360 degrees of complete mechanical and electrical contact for maximum reliability. PL-259 center pins are hand-soldered, and Type-N center pins are machine-crimped by trained assembly techs to assure a proper connection. Next Generation PL-259 connectors feature: * Full diameter, full-length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double-knurled threaded shells for secure finger tightening These high-quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies are available in selected lengths and at any length in the Custom Cable Builder, only from DX Engineering! *U.S. Patent D745849

5.0 out of 5 stars ( 6 )

$55.99

—

$573.70

DX Engineering Vertical Antenna Feedpoint Cables

DX Engineering vertical antenna feedpoint cables are designed to convert the Hustler BTV base connections to a PL-259 type connector. Just add a bulkhead connector to make them to your feedline and you're done! They will also work great for the DX Engineering radial plate. The cables are manufactured from RG-8X cable, have a silver-plated, brass bodied, PTFE dielectric PL-259 connector, and special shrink tubing to help promote weather resistance. The other end of the cable uses a #10 outer ring terminal, a 1/4 in. center ring terminal, and has a 50 ohm rating.

4.8 out of 5 stars ( 5 )

$47.99

Consolidated Wire Coaxial Cable Assemblies

Consolidated Wire Coaxial Cable Assemblies are low loss coaxial cable assemblies engineered for specialized RF device interconnections up to 6 GHz. Crafted with precision, these lightweight cable assemblies feature a PTFE dielectric insulating material. The FEP (Fluorinated Ethylene Propylene) jacket on the RG316 series and PVC (Polyvinyl Chlorine) jacket on the RG174 cables offers outstanding UV and chemical resistance to ensure durability in challenging environments. The wide operational temperature range, flexibility and quality BNC or SMA connectors make these cable assemblies the perfect choice for your next project.

5.0 out of 5 stars ( 6 )

$9.99

—

$29.99

DX Engineering's RG-8X 50-ohm Coax Cable Assemblies

DX Engineering RG-8X 50-ohm Coaxial Cable Assemblies are made from our very flexible low-loss, gas-injected foam dielectric feedline. Featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket good for direct burial, our DXE-8XDX series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics, very good shielding, and lower loss. RG-8X 50-ohm Coaxial Cable Assemblies come complete with high quality silver plated PTFE dielectric PL-259s. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. Order some extras today, to have on hand for the next time you add, change, or rearrange your equipment. DX Engineering RG-8X 50-ohm Coaxial Cable Assemblies are perfect in every station!

Not Yet Reviewed

$33.99

Armoloq RF Cable Relocation Kits

Armoloq RF Cable Relocation Kits are the ideal complement to the Armoloq Tactical Protective Armor (TPA) Modular Radio Mounting Frames. They simplify the process of relocating the RF connection to a more accessible and convenient position when the radio is secured within the TPA frame.

Not Yet Reviewed

$99.99

Comet Adapter Cables

Get your HT or scanner connected quickly using one of these Comet adapter cables. They are manufactured from quality materials and feature pre-terminated connectors for maximum durability. Available in a variety of different combinations, these adapter cables will have you up and running in no time.

4.96 out of 5 stars ( 78 )

$16.95

—

$19.95

DX Engineering RG-6/U 75-ohm Quad-Shield Coax Cable Assemblies

Our new DX Engineering RG-6/U 75-ohm Quad-Shield Coaxial Cable Assemblies are constructed from our own premium DX Engineering brand RG-6/U 75 ohm cable and superior quality weather-sealed nickel-plated compression F connectors. Their best-in-class design reduces loss and provides greater protection against electromagnetic interference. Available in specific lengths between 3 ft. and 200 ft., these pre-assembled cables with F connectors are your most convenient ultra-high quality RG-6/U cable solution. These RG-6/U cable assemblies are ideal for many applications such as active or passive HF Amateur Radio receive antenna systems, magnetic loop antennas, Beverage antennas, over the air TV reception, FM broadcast reception, CATV systems, raw video distribution and satellite radio installations like Sirius/XM. In fact, their low-loss characteristics are excellent up to the microwave frequencies that Satellite Radio systems employ! Our RG-6/U cable assemblies have gas-injected polyethylene foam dielectric for flexibility and moisture resistance. Their 18 AWG center conductor is copper-clad steel and is durable in the extreme. They have two foil shields plus two high-density aluminum braids for ultimate four-layer RF shielding. Their UV protected black exterior jacket is tough PVC (polyvinyl chloride). DX Engineering RG-6/U cable impedance is 75 ohms with an 83 percent velocity factor and have a minimum bend radius of 2.50 in. This is absolutely the best RG-6/U cable available and it's RoHS compliant! Look at these attenuation figures per 100 ft.: 5 MHz: 0.6 dB 30 MHz: 1.1 dB 55 MHz: 1.6 dB Are you installing or upgrading any receiving antenna or video distribution system that uses RG-6/U cable? If so, then these exceptional DX Engineering RG-6/U 75-ohm Quad-Shield Coaxial Cable Assemblies will make your installation easier and your results so much better!

5.0 out of 5 stars ( 13 )

$28.99

—

$86.99

DX Engineering RG-174 50-ohm Hi-Viz Orange Mini Coaxial Assemblies

DX Engineering RG-174 50-ohm Hi-Viz Orange Mini Coaxial Cable Assemblies feature high quality BNC male connectors. An easy-to-see orange jacket on this extremely thin, 0.11 inch diameter, super flexible cable is a smart choice for SOTA, POTA and other quick-deploy portable antennas that are fed with a 25, 35 or 50 ft. length. These 1.5, 3 and 6 ft. coax assemblies in orange are easy to identify on the test bench and behind the radio for QRP and receive only connections. How is this a good choice? CLICK the cable to see the product page. The OVERVIEW has a Loss Chart with interesting info. The efficiency of this amazingly thin coaxial cable is unexpectedly good, adding slightly more attenuation for a given length as compared to larger, heavier coax on HF. For typical applications with portable antennas and equipment interconnections, the losses are inconsequential on the HF bands with the cable lengths offered. A typical portable antenna used with a 25 ft. cable has 0.73dB loss on 14 MHz (20M band) which represents only 15% loss. An extreme example is with a 50 foot DXE-174VDB050 cable used on a 10 meter (28 MHz) antenna has just over 2dB attenuation. Even this power loss of 38% results in an imperceptible difference at the receiving end of a radio contact. Losses are insignificant with DXE-174V cable assemblies on HF bands, especially with 1.5, 3 and 6 ft. length jumpers, or with 25 and 35 ft. cables. Use DX Engineering RG-174 50-ohm Hi-Viz Orange Mini Coaxial Assemblies for HF POTA and SOTA antennas that are easier to wrap up, carry, install and pack up. They're ready for your HF portable operations and much more! NOTE: These cable assemblies are NOT intended to be used for long lengths on VHF or UHF antennas, on frequencies above 50 MHz with significant loss.

Not Yet Reviewed

$16.75

—

$37.05

PackTenna Coaxial Cable Assemblies

PackTenna Coaxial Cable Assemblies are available in RG-316 and LMR195 cable types, these assemblies feature BNC male connectors in both straight and right-angle configurations for flexible cable routing. The 3-foot cable is ideal for short interconnects between radios, tuners, or amplifiers, while longer lengths are well-suited for longer HF/VHF/UHF cable runs.

Not Yet Reviewed

$19.00

—

$28.00

DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies

DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies are very flexible, solid dielectric, braided shield cable intended for RF connections to SO-239 and BNC equipment and antennas. These assemblies are suitable for moderate-power applications where flexibility is a key consideration. NOTE: These premade cables come with either high quality, silver plated 83-1SP PL-259 or silver plated BNC Male connectors installed at each end of the DXE-58AU cable, for use on any equipment with SO-239 or BNC Female connectors. Slightly smaller than RG-8X cable, DX Engineering RG-58A/U Coaxial Cable Assemblies are made from our new-process DXE-58AU solid dielectric cable. Featuring a stranded tinned copper center conductor, a braided tinned copper shield and a standard Type I PVC jacket, our 58AU cable assemblies are intended for low to moderate power, test and mobile applications where short runs and flexibility are required. DX Engineering RG-58AU offers easy handling characteristics and good shielding. Plus, this solid dielectric cannot gather moisture and has longer viability than old RG-58 foam cables. INFO: Type-I PVC is not intended for permanent installation in outdoor locations where sun exposure is expected. This cable can last well over 10 years if it is protected from UV sunlight. Our RG-58AU Coaxial Cable Assemblies come complete with high-quality silver-plated Delrin-dielectric PL-259 or BNC male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. Their center conductors are hand soldered and inspected. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. When you are looking for lightweight and flexible pre-assembled cable assemblies and want a high-quality, reliable product, look no further than our own DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies.

Not Yet Reviewed

$34.99

—

$55.99

DX Engineering RG-214 Double Shielded 50-ohm Coaxial Cable Assemblies

DX Engineering RG-214 Double Shielded 50-ohm Coaxial Cable Assemblies feature superior RF isolation and rugged flexibility for critical applications in the shack and on the tower. These high-quality assemblies, with PL-259s or Type N connectors, feature our specially manufactured MIL-SPEC DXE-214. This is a tough yet flexible coax with 12-gauge silver plated stranded copper center conductor, solid polyethylene dielectric and TWO layers of silver plated braided copper shields to provide exceptional RF isolation performance and superior power handling. DXE-214 coax assemblies are perfect for use where many cables are bundled together and higher RF isolation is desired. Use DXE-214 cables for antenna feedlines on towers, especially for rotator loops, as the solid polyethylene dielectric provides repeated flexing without concern of center conductor migration. Plus, these cable assemblies excel at maintaining RF isolation in the shack or in the equipment room of stations with many antenna feedlines. DXE-214 is specifically recommended for use in VHF/UHF duplex repeater applications. DX Engineering RG-214 Double Shielded Cable Assemblies are terminated with either Amphenol 83-1SP silver plated PL-259 connectors or our silver plated Type N connectors. Shields and center pins are hand soldered by trained assembly techs. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! Order DX Engineering RG-214 Double Shielded 50-ohm Coaxial Cable Assemblies - the ultimate flexible choice for RF isolation and power handling.

5.0 out of 5 stars ( 3 )

$79.99

—

$249.99

DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies

DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies are available in several useful lengths, terminated with DX Engineering Next Generation PL-259 connectors; ultra-high quality all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. DX Engineering Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that fully engage even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and adhesive heat-shrink weather-sealed for the ultimate in service longevity Times Microwave Coaxial Cables are recognized as superior RF cable products. Times Microwave Systems LMR® UltraFlex (UF) cables have a stranded bare copper center conductor, a gas foam polyethylene dielectric, and a rubber-like black thermoplastic elastomer jacket designed for repeated bending. LMR®'s RF shielding is typically 50 dB greater than off-brand single braided shield coax. LMR® UltraFlex copper braid and multi-ply bonded foil outer conductor shields provide greater than 90dB shielding. That is better than 180 dB isolation between two adjacent LMR® cables. DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies are an excellent choice for a variety of indoor, mobile, portable, and outdoor applications.

Not Yet Reviewed

$42.99

—

$196.99

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Adapter Assemblies

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Adapter Assemblies feature different silver plated connectors at each end – high quality BNC and PL-259s PTFE dielectric connectors – especially useful for POTA activations and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are the most flexible and lowest loss high-quality orange coaxial cable assemblies on the market. DXE-8XV cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. The actual jacket color delivered can vary. DXE-8XV is the part number for this coaxial cable sold by the foot and is also available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 1 )

$39.99

—

$124.99