Availability
HF Directional Antennas
EAntenna HEX6B Six Band Hexbeam Antenna
EAntenna HEX6B Six Band Hexbeam is a directional HF antenna for the six Amateur bands 20, 17, 15, 12, 10 and 6 meters. This design follows the ideas of G3TXQ Steve Hunt, the originator of the Broadband version of the Hex Beam antenna. However, this mechanical construction is a version refined by EAntenna with their long-standing antenna engineering experience. The result is an efficient, lightweight portable antenna for the high HF DX bands, which is ideal for use for DXpeditions and vacations. An installation at 20 ft. above the ground can work quite well, but a tower-mounted Hexbeam at a height of 35 to 60 ft. is known to perform as intended and produce excellent DX results. The HEX6B works as two element beam on each band. Ready-to-use wires and ropes are attached to the fiberglass struts and due to the mechanical tension of the struts, the beam is stretched to its fixed size all the time, so there is no sag on the wires. The radiator dipoles are connected to the vertical center support, with each band wire element attaching with screw clamps. The center support is designed as a coaxial transformer and balun, providing a particularly good match on each band, with one feedline for all six bands. The HEX6B forward gain is approximately 3dBD or better, the front/back ratio is between 13 and 22dB. SWR is 1.5:1 or better on all bands except 10m, where SWR is 2:1 or better. Each band can be used in full bandwidth without a tuner. The maximum allowed power is 5 kW. The fiberglass tubes are double coated against UV radiation. The setup of the HEX6B six band beam is simple and can be done by one person in about 30 minutes. All ropes and wires are ready, cut to length, so no tuning is required. Due to the low weight of only 18.7 lbs. (8.2 kg) this hex beam can be installed on a light aluminum push-up mast. Rotation is either done with a small rotator or by hand. The HEX6B mast clamp accommodates poles with a Diameter from 1.10 -2.05 in. (28-52mm).
( 6 )
$851.99
DX Engineering XB-5 Hexx Beam HF Antenna
The DX Engineering XB-5 Hexx Beam is a lightweight directional five-band HF antenna for the 20, 17, 15, 12 and 10 Meter bands that is ideal for permanent or temporary installations. What are the benefits of this oddly shaped HF beam antenna? There are many, such as its small turning radius and full legal-limit power handling on all bands. But the most important are that the XB-5 Hexx Beam receives signals very well and transmits RF very efficiently. Its special configuration of full-size wire elements reject noise so more signals are heard. Months of development have culminated in this advanced antenna design for easier assembly, improved SWR and better bandwidth while maintaining excellent front-to-back performance. The DX Engineering XB-5 is our best Hexx Beam to date. DXE-XB-5 is the complete HF antenna package of specialized DX Engineering XB-5 Hexx Beam components; some are new and pre-assembled. These essential components include the patented* Hexx Hub and the Stainless Steel and PTFE Rigid Flat Feeder which is fully balanced with the Maxi-Core® 20 1:1 Current Balun and Mount. Also included are the all-new Heavy-Duty "Ice" Spreader Support Ropes with thimbles and stainless steel carabiners, better fiberglass Center Post and Spreaders, the Heavy-Duty Mast Mount, newly configured Element Wire Kits with the unique DX Engineering Wire Guides and innovative Element Spacer Insulators. The DX Engineering XB-5 Hexx Beam design has a number of important advantages over other Hex Beams or a mini-Yagi: - New, easy and faster assembly - fewer parts to speed completion of the antenna project - Pre-made 4.4 mm heavy duty "ice" support ropes with thimbles and stainless steel carabiners - High CMI Balun (1:1 5kW) and Mounting Bracket included - New Heavy-duty Mast Plate with DXE Saddle Clamps - Strong fiberglass without slits - Pre-sized and pre-drilled element spacer insulators designed for simple antenna assembly and tuning adjustment - Improved SWR band coverage - Small turning radius - the XB-5 Hexx Beam has a turning radius of 11' - Gain - 5 dBi (3 dBd), depending on band - similar to 2 element Yagi, far exceeding the performance of multi-band mini-beams - Front-to-Back – greater than 20 dB, depending on band - Wind balanced - Hexx symmetry reduces torque on the rotator - Light weight – about 25 lbs. fully assembled - Wind load – only 5 square feet wind surface - Can be turned with a light duty rotator - Performs well at low heights - good results at 25 to 35 feet above ground - Handles full legal limit power – no power restriction as on competing antennas - Low Noise results - approaches performance of closed loop antennas - Full length HF antenna elements - no lossy coils or traps - Five-Band Stainless Steel/PTFE Rigid Feeder System – balanced for best pattern - Requires no matching network - direct single 50 ohm coax feed The DX Engineering XB-5 Hexx Beam is one of the best performance values on the market for a directional HF antenna. *(US Patent No. 8,669,911, US Patent No. D 624,060, British Patent No. GB248003 B)
( 3 )
$1,247.92
EAntenna HF Rotatable Antennas
EAntenna HF Rotatable Antennas include a comprehensive range of mono-band and multi-band Yagi beams and rotatable Delta Loops and Dipoles. Find the band coverage and performance antenna of your dreams right here. For example, the exciting EAntenna 59+ provides great performance on 20, 17, 15, 12 and 10 meters! Check out the specs on this great line of HF directional antennas. DX Engineering offers EAntenna because their attention to manufacturing detail is excellent! Their Yagi, log periodic, and rotatable dipole antennas are built with high-quality stainless steel hardware and aircraft-grade aluminum. As you look through these selections, be aware that advanced, cutting-edge computer modeling and optimization techniques were used to produce every one of the EAntenna premier HF beam antennas and state-of-the-art VHF and UHF Yagi antennas. Their mechanical designs are very robust in every way, as most are rated for at least 100 mph wind survival. To see additional information about each antenna, click on the "More Details" link on the antenna of interest. Then click the Specifications tab to see all of the physical and electrical characteristics of that antenna. EAntenna products are offered exclusively in North America by DX Engineering. Plus, we can ship these great antennas internationally! When you're making plans for a new antenna at your station, look no further for the outstanding solutions by EAntenna, "The Best Choice for Your Antenna System!" NOTE: Manuals are normally supplied bilingual. If your manual lacks an English section, contact DX Engineering for an English version.
( 47 )
$355.99
—
$2,215.99
OptiBeam HF Directional Antennas
OptiBeam antenna technology has achieved directional antennas with extraordinary electrical properties, including the highest efficiency, optimum band coverage, nearly constant gain and unchanging radiation pattern across the band, and low SWR. These antennas maintain consistent electrical characteristics under all weather-conditions and include a high power balun with UHF female connector for your 50 Ohm coaxial cable. OptiBeam Antennas are distinguished by their advanced mechanical qualities. Specially configured, stable and properly shaped element holders, robust square and round booms with effective and very solidly-built element transitions are OptiBeam exclusives. They provide advanced physical properties, including proper balance and the highest stability of the entire system. Elements are perfectly aligned and secured against torsion with minimal sag for a visually pleasing appearance. OptiBeam antennas are made for those who understand the true value of investing in proven electrical performance and unequalled mechanical quality for the ultimate in reliability. They are built to withstand the harshest conditions using the very best materials, including high quality aluminum alloys, UV stable synthetic parts and stainless steel hardware. OptiBeam antennas are designed to be easier to build than others, arriving in subassemblies with every part carefully sorted, clearly labeled, and extremely well packed for worry-free shipment and straightforward installation. In 2025, the OptiBeam brand of products was exclusively acquired by WiMo Antennen und Elektronik GmbH. The OptiBeam portfolio is now produced by WiMo and integrated into its product offering. With this acquisition, WiMo will integrate the technical expertise and know-how gained from OptiBeam's many years of experience in antenna technology and will provide new impetus with its extensive service and sales network. The primary goal is to successfully continue OptiBeam's antennas, ensure long-term customer service and spare parts availability, and leverage development potential. For enthusiastic operators of all pursuits, OptiBeam provides the advantage of pure performance. Proven in the field and confirmed by the most demanding hams around the world – choose OptiBeam for your station.
( 5 )
$1,338.99
—
$6,172.00
Diex Antennas Multi-Band Log Periodic Antenna
Diex Antennas Multi-Band Log Periodic Antennas deliver exceptional directionality and full coverage across the 20 through 10-meter amateur bands. Expertly engineered and crafted in Brazil using high-quality aluminum tubing and durable materials, these antennas are built to endure harsh environments while providing long-lasting, high-performance operation. With a power rating of up to 2000 Watts PEP or 700 Watts continuous duty, these antennas are ready for demanding applications. It offers 8.55dBi of gain, helping your signal reach farther—whether across the country or around the globe. Designed for efficiency, the Diex Log Periodic maintains a low SWR across its entire frequency range, minimizing the need for adjustments or an external antenna tuner.
Not Yet Reviewed
$1,699.99
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles offer high performance multi-band HF operations, and they are an excellent choice where there's not enough space for a full-size dipole or Yagi. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these unique multi-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. DIEX Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles power handling is 1500W PEP SSB, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that a directional HF antenna should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 2 )
$409.99
—
$765.99
WiMo - EAntennas 2850MOX Dual Band Moxon Antenna for 10 and 6 Meters
WiMo - EAntennas 2850MOX Dual Band Moxon Antenna for 10 and 6 Meters is perfect for Sporadic-E QSOs on these bands, as well as for local and regional weak-signal operations on SSB, CW, and Digital Modes. The 2850MOX is a horizontally polarized directional antenna that offers high gain for its very compact dimensions. This antenna features an additional third element for especially good gain on the 6 meter band. The 2850MOX Dual Band Moxon advantages: - Radiator configuration offers high gain: 8.3 dBi - 6m, 10.5 dBi - 10m - Relatively compact dimensions - Front-to-back ratio is very good; 12dB on 6m, 21dB on 10m - Flat SWR curve over a wide bandwidth The 2850MOX Dual Band Antenna covers 28-29.7 and 50-52 MHz, requires only one coax feed line, and the included 3kW balun has an SO-239 connector. It has a short boom of 180cm (5.9 ft.) and a low weight of only 6.2kg (13.67 lbs.). Ideal for the restricted property and for temporary or portable operations, this antenna can fit well on an existing mast where space is limited. Join the fun of weak-signal operations, locally, regionally or long range via Sporadic-E for DXing or contesting on the 10 and 6 meter bands. The 2850MOX offers high performance with very reasonable dimensions at a low cost.
( 8 )
$469.99
InnovAntennas DXC-140 40 Meter Rotatable Dipole
InnovAntennas DXC-140 40 Meter Rotatable Dipole covers the entire 40-meter band with particularly good efficiency, impressive SWR bandwidth and a very reasonable wingspan, just over 39 ft. (12m). There are several methods to shorten a mast-mounted rotatable dipole, including loading coils and capacity hats. The position of the coils is critical to efficiency--closer to center is mechanically easier, further out is electrically better. The designer has used both methods to build the Delta C-140 antenna robustly and efficiently, limiting the size to a turning radius under 20 ft. (6 m) that many radio amateurs can easily mount on their tower mast and rotate within their property limits. The advantage of this design is a very large usable bandwidth of the antenna--the DXC-140 can be used over the entire internationally approved range from 7.0 to 7.3 MHz without having to use a tuner (SWR 2:1 or better). In the DXing range from 7.0 to 7.2 MHz, the SWR is usually equal to or better than 1.6:1, making the efficiency of the antenna 89 percent! Due to the robust construction of the DXC-140, no guy wires are necessary. Some of the images of this model installed show examples with guy wires, as chosen by individual user dependent upon the location, due to the expectation of snow and ice, for example. However, the mechanical design and construction will handle heavy loads, with the element diameter of 2.17 in. (55mm) in the center with a wall thickness of 0.078 in. (2mm). The element diameter decreases towards the end of the element save weight, but the ends still have a diameter of 0.98 in. (25mm) to easily support the capacity hats. All in all, the DXC-140 antenna combines a carefully calculated design with a very robust construction from an experienced antenna designer. This is also supported by the materials used: UV-resistant insulators, seawater-proof stainless steel hardware, and aircraft-grade aluminum elements. The result is a rotatable dipole with high efficiency, with an overall length of only 39.4 ft. (12 m) and a weight of only 18.7 lbs. (8.5 kg). The InnovAntennas DXC-140 40 Meter Rotatable Dipole is creating enthusiasm for many radio amateurs around the world. Order the DXC-140 for your station from DX Engineering.
( 1 )
$1,128.99
Diex Antennas Single-Band Full Size Rigid Rotatable Dipoles
Diex Antennas Single-Band Full Size Rigid Rotatable Dipoles provide coverage of one specific HF band. Built as a full-size resonant dipole, Diex aluminum tubing antennas provide excellent performance and are handled with a lighter tower and smaller rotator, offering a very economical alternative to the expense of a Yagi. Crafted with precision in Brazil using quality materials, they are designed to withstand tough environments assuring long-lasting service. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these single-band HF antennas provide very good directionality depending upon installed height above ground. They feature the flexibility of physical adjustments to set the lowest SWR to a specific frequency. Diex Antennas Single-Band Full Size Rigid Rotatable Dipoles power handling is 1,500W+ PEP, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 6 )
$115.99
—
$209.99
Diex Antennas Two-Band Trap Shortened Rigid Rotatable Dipoles
Diex Antennas Two-Band Trap Shortened Rigid Rotatable Dipoles offer high performance multi-band HF operations, and they are an excellent choice where there's not enough space for a full-size dipole or Yagi. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these unique multi-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. DIEX Antennas Two-Band Trap Shortened Rigid Rotatable Dipoles power handling is 1500W PEP SSB, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that a directional HF antenna should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 2 )
$281.19
—
$295.99
Diex Antennas Two-Band Shortened Rigid Rotatable Dipoles
Diex Antennas Two-Band Shortened Rigid Rotatable Dipoles provide coil-shortened specialized coverage of two non-adjacent HF bands that can complement band coverage of existing antennas. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotatable mast, these unique two-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of coil-shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. Diex Two-Band Shortened Rigid Rotatable Dipoles power handling is 300W PEP SSB and 100W maximum for digital modes, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 7 )
$215.99
—
$309.99
Chelegance JHEX-6 HF 6-Band Hex Beam Antennas
Chelegance JHEX-6 HF 6-Band Hex Beam Antennas are powerful, full-size 6-band Hex Beam antennas built for hams who want serious performance—whether you're into contesting, chasing DX, or talking with fellow hams around the globe. Covering the 20, 17, 15, 12, 10, and 6-meter bands, and rated for 2000 watts PEP, the JHEX-6 is ideal for DXing and high-duty-cycle operation. The JHEX-6 is engineered for rapid deployment, featuring a modular, tool-free design that allows for quick assembly and effortless installation by a single operator—ideal for stationary installations, field operations, and solo deployments. With full-size elements on each band, it delivers exceptional gain and directivity, making it a top-tier choice for demanding operators. A 1:1 balun ensures optimal feedline performance, while its lightweight construction—weighing just 26.5 pounds—enhances portability and ease of setup. Built for long-term reliability, the JHEX-6 incorporates precision-molded cable lugs, a robust beam structure, and aluminum-reinforced plug-in joints with butterfly screw connections for fast, secure assembly. Its rugged 1.40-inch (35mm) 304 stainless steel base tube provides a dependable mast mounting solution, even in harsh environmental conditions.
Not Yet Reviewed
$1,199.98
Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles
Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles provide coil-shortened specialized coverage of a single HF band that can complement band coverage of existing antennas. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotatable mast, these unique single-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of coil-shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles power handling is 300W PEP SSB and 100W maximum for digital modes for the 20, 30 and 60M models, 1000W PEP for 80M and 1500W PEP for 40M, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 7 )
$215.99
—
$679.99
Diex Antennas DXM Series 2 Element 40 meter Directional Antennas
Diex Antennas DXM Series Single-Band Shortened 2 Element Directional Antennas provide coil-shortened specialized coverage of a single HF band that can complement band coverage of existing antennas. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotatable mast, these unique single-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of coil-shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. Diex Antennas Single-Band Shortened Rigid Rotatable Dipoles power handling is 300W PEP SSB and 100W maximum for digital modes for the 20, 30 and 60M models, 1000W PEP for 80M and 1500W PEP for 40M, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that HF antennas should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
Not Yet Reviewed
$1,129.99
InnovAntennas DXR Series Multi-Band HF Beams
InnovAntennas DXR Series Multi-Band HF Beams have short booms with full-size elements or capacity-loaded shortened elements, all with excellent performance, making them very popular internationally. The DXR Series interlaced-element antennas, optimized by G0KSC over a long period of time, achieve the best possible balance between compact size and performance. For the DXR Series Multi-band Yagis, equal attention was paid to a very solid construction and sufficiently small component and packaging size, to keep shipping costs within reasonable limits. Click on any model listed for specific details and specifications. InnovAntennas DXR Series Multi-Band HF Beams are available exclusively from DX Engineering in North America. Important features of InnovAntennas DXR Series Multi-Band HF Beams: * No traps, matching links, or hairpins * Only one feed line for all bands * Careful selection of materials without regard to cost * Very robust construction with still manageable package size The DXR Series beams use a 1.97 x 1.97 in. (50 x 50 mm) square boom with 0.078 in. (2 mm) wall thickness. A square boom has the advantage that the elements cannot twist in the plane. On the other hand, it is slightly heavier than a round boom of the same stiffness. The DXR Yagis do not require any bracing of the boom. The longest elements are 1.378 in. (35 mm) diameter in the middle and taper relatively quickly to achieve a good compromise between weight and strength. This construction also helps to avoid constant vibration even in light winds. With these multi-band Yagis, care has been taken to ensure that there are never more than the elements of three bands nested within each other. This is because each additional element for one band can cause interference on another band. This negative effect was avoided by careful manual optimization. The result is the best possible matching over a wider band range than other antenna designs. In most cases, no tuner is necessary; the SWR minimum can be precisely set by adjusting the element lengths. Due to the robust construction and the absence of moving or electrically active components such as coils, traps, hairpins, etc., an InnovAntennas DXR beam is maintenance-free for many years. The insulators are UV-resistant and designed for a wide temperature range. The mounting hardware uses sea-water resistant stainless steel and the aluminum is type T6 6066/6082, which is also used in aviation. It is nice not to have to climb the mast every year to maintain the antenna. The DXR Series Multiband beams are designed to require only one feed line. This makes installation on a mast with a rotor very easy. And the use of modern SDR transceivers, which allow the observation of several bands at the same time, becomes really useful. The one feed line is connected directly to the solid distribution rails of the fed elements. By avoiding baluns, matching elements, traps, or hairpins for tuning, transmit power is only limited by the coaxial cable and connectors. Note: Front-to-back ratio (F/B) and SWR bandwidth data for the DXR Series will be added as it becomes available. Many models of the DXR Series are available as a "super-compact" version, on which the longest elements have been shortened with capacity hats, thus reducing their turning radius considerably. The installation of these impressive antennas is possible even where space is limited.
( 4 )
$1,439.99
—
$2,097.99
Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles
Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles are compact all aluminum self-supported dipole antennas specifically designed for "Limited-Small space" applications. Designed for use with an antenna tuner, each element is fitted with an M5 stud and wing nut to enable easy feed wire connection. The central bracket has two U bolts to allow attachment to a 50mm (1-7/8 in.) OD mast. Radiating elements are manufactured from telescoping 25mm and 22mm diameter "drawn," not extruded, aluminum tubing. This makes them flexible and extremely resilient to high winds and bird landings. The width of the assembled antenna is only 6.8 meters (22.31 ft.). They are configured to operate in a frequency range of 3-54 MHz with the aid of a manual/auto tuner. Ultimate band coverage is subject to the functional range of your antenna tuner. If not using a remote mast-mounted tuner, then an RF choke or balun should be used at the antenna to limit RFI. Dipole elements are two-piece to reduce the shipping length to 202 centimeters (79.53 in.). These antennas are very easy to assemble and with a weight of only 3 kg (6.6 lbs.) they are extremely easy to erect. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. These antennas are ideal for pairing with an LDG-RT-RC-100 remote autotuner and a Channel Master CNM-9521A light Duty Rotator System. Order Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles and accessories from DX Engineering!
( 5 )
$429.99
Diex Antennas DXS Series Multiband Directional Antennas
Diex Antennas DXS Series Multi-band 3 Element Yagi Antennas delivers high-performance, Multi-band operation for the 40, 20, 15, 10 and 6-meter amateur bands. The DXS antenna series features three tunable aluminum elements, engineered for optimal directionality and gain. With a power handling capacity of up to 1,500 watts, these antennas are built to perform under demanding conditions. Crafted in Brazil using quality materials, the DXS Series is designed for long-lasting, trouble-free service. Easy to assemble and require only a modest mast or tower, these antennas offer an economical and effective solution for getting on the air.
( 1 )
$1,279.99
—
$1,745.99
Diex 3 Element Monoband Full Size Yagi Antennas
Diex 3 Element Monoband Full Size Dipole Antennas are full sized directional antennas covering the 20 through 6-meter amateur bands. Expertly engineered and crafted in Brazil from quality aluminum tubing and durable materials, these antennas are built to endure harsh environments while providing long-lasting, high-performance operation. With a power rating of up to 2000 Watts PEP, these antennas are ready for demanding applications. Offering at least 8 dBi of gain and greater than 500 kHz of bandwidth at less than 2:1 SWR, these monoband antennas will help your signal reach further – whether across the country or around the globe. Designed for efficiency, these 3 Element Monoband will get your signal further and let you chase far away DX.
( 3 )
$379.99
—
$995.99
DX Engineering Skyhawk Tri-Band Yagi Antennas
DX Engineering Skyhawk™ Tri-Band Yagi Antennas are the choice of experienced DXers, especially if your interest is HF contesting. DX Engineering Skyhawk™ antennas provide the highest payback in performance and operating pleasure compared to any other single component in your station. The only better antenna choice is to combine one of our DX Engineering Skylark™ Dual-Band Yagi Antennas with the Skyhawk™! These well-designed, single-tower systems offer outstanding performance without the headaches of maintaining more substantial antenna farms. DX Engineering Skyhawk™ antennas reflect the latest computer-optimized design for maximum gain and bandwidth. They are built from the finest materials utilizing heavy-duty aluminum and all stainless steel hardware. Skyhawk™ operates from a single feed line and has a 90 mph wind survival rating! Have you ever had to replace a rotor in February? Skyhawk™ antennas offer minimal wind-loading for their size and are torque-balanced to reduce wear and tear on your rotor. Assembly is easy, as tower top adjustments have been eliminated and the elements are truly locked in place. DX Engineering Skyhawk™ features include: * 90 MPH wind survival rating * EZ-mount system for attaching antenna to mast * All parts de-burred * Stainless steel pop-riveted element locking * No user adjustment - just assemble it and put it up Additional specifications include: 20 meters: * Three elements * Effective boom length: 23 ft. * VSWR: less than 1.4:1 between 14.0 and 14.35 MHz, measured at feed-point * Front to back: >20 dB across the entire band * F/B peaks at 14.150 MHz at 21 dB * Gain: better than 7 dBi across band * 7.4 dBi gain at 14.350 MHz * Front lobe beam width (-3dB points) 63 degrees 15 meters: * Three elements * Effective boom length: 15 ft., 6 in. * VSWR: less than 1.5:1 between 21.0 and 21.45 MHz, measured at feed-point * Front to back: >16 dB across the entire band * F/B peaks at 21.350 at 24.5 dB * Gain: better than 7 dBi across band * 7.6 dBi gain at 21.45 MHz * Front lobe beam width (-3dB points) 56 degrees 10 meters: * Four elements * Effective boom length: 16 ft., 9 in. * VSWR: less than 1.5:1 between 28.0 and 28.9 MHz, measured at feed-point * Front to back: >14 dB across the entire band * F/B peaks at 28.5 at 21 dB * Gain: better than 7.7 dBi across band * 9.2 dBi gain at 28.9 MHz * Front lobe beam width (-3dB points) 47 degrees Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. So, what are you waiting for? Get a DX Engineering Skyhawk™ Tri-Band Yagi atop your tower, hook up your coax, and start working some serious DX! You've always heard about DX Engineering quality. DX Engineering Skyhawk™ Tri-Band Yagi Antennas are available now. Order yours today and enjoy great DXing with quality and value!
( 3 )
$2,378.97
InnovAntennas DXC-240 2 Element Compact 40 Meter Yagi
InnovAntennas DXC-240 2-Element Compact 40 Meter Yagi features very good efficiency, a relatively small footprint and exceptional bandwidth. There are several methods to shorten a dipole or the elements of a beam, including loading coils and capacity hats. However, coils reduce efficiency if they are mounted too close to the middle of the Yagi and capacity hats can reduce the length by only a few percent. Through careful calculation and robust construction, InnovAntennas designer Justin Johnson, G0KSC, has managed to craft this two-element beam for 40 the meter band with a boom that is just under 23 ft. (7m) in length. The elements have a maximum length of 37.73 ft. (11.5m) and this beam achieves a 2:1 SWR bandwidth of 120 kHz without the use of an antenna tuner. The DXC-240 is a rugged, seriously heavy-duty 40 meter Yagi featuring a 2.362 in. (60mm) square boom with a wall thickness of 0.079 (2mm), making it very stable, even without truss ropes. The elements use 1.97 in. (50mm) diameter aluminum tubes in the middle, which quickly taper to 0.98 in (25mm) at the ends. The DXC-240 has a wind area of 13.5 sq. ft. (1.25 sq. m), weighs 110 lbs. (50 kg) and has a turning radius of 22.1 ft. (6.73 m). Solidly constructed, efficient loading coils are at the middle of each half element, exactly where they belong to minimize losses and maximize bandwidth! Additional efficient reduction of length is achieved with capacity hats at the ends of the elements. The result is a compact 2-Element Yagi for 40 m that can achieve gain of about 10.53 dBi at 65.6 ft. (20 m) above ground with a spec of 6.29 dBi free space gain and a typical front to back of 15 dB. Impedance matching with an adjustable hairpin that provides a 50 ohm feedpoint that does not negatively affect the usable bandwidth. Order the InnovAntennas DXC-240 2-Element Compact 40 Meter Yagi from DX Engineering. Enjoy an efficient and heavy-duty 40 meter 2-element beam that is so compact, it can be installed at many radio amateur's stations.
( 1 )
$2,160.00
InnovAntennas DXE12-6 Heavy Duty HF+6M Yagi
InnovAntennas "DXE Twelve-Six" is a heavy-duty 12 element multi-band HF plus Yagi that covers the 20, 17, 15, 12, 10 and 6 meter bands with a single coax connection to match modern HF+6m transceivers. Excellent performance on each band is achieved by direct feed and no traps, coils or hairpins for class-leading radiating efficiency. This ruggedly built beam antenna is ready for harsh weather environments with aerospace grade T6 6066/6082 aluminum tubing, UV and temperature protected insulators and all stainless steel hardware. The stout, modest length 17.5 ft. (5.33m) boom is made of 2 inch (50mm) square tubing and perfectly interleaved rigid fast-taper elements easily shed the wind. Choose this HF beam for long-term reliability and power handling that exceeds most coax specs. With low SWR across all six bands, 20 through 6 meters, InnovAntennas DXE 12-6 is a great value that packs a punch.
Not Yet Reviewed
$1,860.00
Momobeam Mono3-20 Monoband Yagi Antennas
Momobeam Mono3 20 Monoband Yagi Antennas are engineered using the latest generation design software to deliver exceptional performance across the entire 20 meter frequency range. With full size elements and precision optimized geometry, these antennas are ideal for operators who want maximum efficiency, gain, and on air reliability without compromise. Built on a robust square boom, the MONO3 20 antennas are designed for easy, accurate assembly. Each system includes an assembly tool, spare hardware (bolts and aluminum tubing), and fully labeled components. All hardware is packaged in clearly marked bags, and every aluminum tube is labeled to ensure a fast, frustration free installation experience. These antennas are suitable for both mast mounting and side mount tower configurations, offering excellent flexibility for station design. A medium duty rotor is required for proper operation. To further enhance performance and reduce feedline issues, every MONO3 20 antenna comes standard with a 3 kW RF choke balun—a premium component that many manufacturers offer only as an upgrade. Momobeam RF Chokes are constructed from high quality, low loss, double shielded coaxial cable with a Teflon dielectric, combined with carefully selected ferrite material sleeved over the cable to create a high impedance path for RF, providing excellent isolation between the antenna and the coaxial feedline.
( 1 )
$1,389.99
InnovAntennas 10M or 11M LFA-Q Loop-Fed Quad Beams
InnovAntennas 10M or 11M LFA-Q Loop-Fed Quad Beams from G0KSC represents significant development of LFA Yagis with a substantial difference: LFA-Q (Loop Fed Array Quad) Beams use top and bottom booms with through-boom LFA Yagi-style loops arranged vertically for every element. This very rugged design achieves better gain for a given length of boom and much lower noise for better signal quality compared to conventional Yagi antennas. InnovAntenna LFA-Q quad structure provides high directivity, eliminating unwanted spurious radiation. They achieve great side and rear rejection while retaining excellent gain, front-to-back and SWR bandwidth across the band. These are amazingly compact, high gain directional antennas, constructed to withstand serious weather conditions! Antennas of this series can be built and tuned to operate on a 500 kHz section of the 10 meter 28 MHz Amateur Band or on the 11 meter 27 MHz Citizens Band. The desired band is easily selected by changing the length of the outer element sections during construction – exact dimensions are provided in the instructions. The driven loop element feedpoint impedance is 50 ohms which allows a direct feed at high transmitting power. Vertical stacking of two or more antennas can significantly increase directivity, gain and signal quality; an interesting alternative when available space prevents the installation of long boom beam antennas. Just like other HF quads, LFA-Q vertical loop-fed quads are inherently quieter than a Yagi of the same size, making them a perfect choice for use in any location with high ambient noise level, such as a city or densely populated neighborhood. There is a 10M or 11M LFA-Q Loop-Fed Quad Beam version that matches your space, support, and wallet: - The 2-element economy version has loop spacing booms of only 2.3 ft. (70 cm); - The 3-element compact version booms are 10.5 ft. (3.2m) in length: - The 4-element performance model boom lengths are 26.9 ft. (8.2 m). Each LFA-Q is very stable mechanically, with mast clamps on each boom, top and bottom! Thanks to the use of high-quality materials, extensive modeling and testing, the durability and reliable performance of InnovAntennas 10M or 11M Loop-Fed Quad Beams is undeniable.
Not Yet Reviewed
$519.99
—
$1,419.99
InnovAntennas 13 Element HF Log Periodic Dipole Arrays
InnovAntennas 13 Element HF Log Periodic Dipole Arrays provide super wideband, high performance from 10 to 54 MHz. InnovAntennas LPDA's are designed using the very latest computer optimization techniques such as Dense Element Log Periodic Dipole Array (DELPA). This type of antenna was designed with specifications for a broadcasting center. Example photos display the DELPA-13 installed at the broadcast center. If you are looking for the best of the best from both a performance and mechanical construction perspective, then look no further than InnovAntennas LPDA! You have come to the right place! The DELPA-13 has 13 elements placed above the 37.73 ft. (11.5 m) by 3 in. (76mm) square boom, from which all elements are insulated. The feed point is 200 ohm and includes a 20 kW 4:1 balun. Feed line between the elements is silver plated hard-drawn copper wire spaced to produce a 300 ohm balanced-line feed. The DELPA-13 provides excellent, consistent results for the frequency range it covers with a relatively limited number of elements. Some of InnovAntennas HF Log Periodic Dipole Array mechanical design benefits include: * Marine grade stainless steel hardware (wherever possible) * Integrated feed line/boom for maximum efficiency, minimum wind-load * Silver plated balanced line feed * Mill finished for highest levels of accuracy and performance Performance specifications of InnovAntennas 13 Element HF Log Periodic Dipole Array DELPA-13: * Typical forward gain: 6dBi * Typical F/B: 15dB * Gain at 33 ft. (10 m) above ground: 10dBi * Power rating: 15 kw+ (further limited by feedline and connectors) * Feed impedance: 50 Ohm * Boom length: 37.73 ft. (11.5 m) * Weight: 165.35 lbs. (75 kg) * Turning radius: 20.67 ft. (6.3 m) * Wind loading: Upon application * Wind survival: 100 mph (160 kph)
Not Yet Reviewed
$4,100.00